Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Avaliação do efeito do extrato hidroalcoólico das folhas de Anacardium occidentale L. em ratos submetidos à colite ulcerativa

Ulcerative colitis is a chronic disease characterized by inflammation in the intestinal mucosa, in most cases affects the colon and rectum. The therapeutic drugs are used as aminosalicylates and glucocorticosteroids, but due to the low response and the various side effects caused by them, reveals the need to search for new sources of useful compounds in the treatment of this disease.The species Anacardium occidentale popularly known as cashew, has been used for centuries in folk medicine in the healing aid of skin and mucosa lesions.Recent studies show its expressive antiulcerogenic effect, what we instigated to assess the effect of the extract of A. occidentaleleaves in rats with acute ulcerative colitis, therefore, 42 rats were used male Wistar, divided into 06 groups, and Negative Control (C) Positive Control (C +), treated with Sulfasalazine (Sz500) and treated with Extract A. occidentale at doses of 50 (Ao50), 100 (Ao100) and 200 mg / kg (Ao200).All groups were submitted to experimental colitis Ulcerative except C-, moreover, C- and C + received saline via gavage for 7 consecutive days while the other groups received their respective treatments.Euthanasia of animals took place on the 8th day in which it was collected intestinal colon sample for later analysis macroscopic, histopathological, morphometric and biochemistry, as well as complementary collection of blood and liver tissue. The extract is rich in saponins and phenolic compounds such as flavonoids (quercetin and kaempferol) and tannins.When the Sz500 groups and 100 showed significant protection to damage to lipids and proteins, among the groups subjected to experimental ulcerative colitis, the animals Ao100 group obtained the lowest score in all parameters analyzed.Treatment with 100 mg / kg of A. occidentale extract seems to have a combination of antiinflammatory, antioxidant, bactericidal and anabolic promoted by the bioactive compounds present in the extract.However, it is necessary to investigate harder treating dose of 100mg / kg to higher doses compared to elucidate more properly the best therapeutic dosage ulcerative colitis.

Obtenção e caracterização de um compósito polimérico de matriz poliéster e reforço/carga de tecido plano de algodão

He was obtained and studied the feasibility of using TPA (Tissue Cotton Plan) screen type, for bagging, with a weight of 207.9 g / m2 in a composite of orthophthalic crystal polyester resin matrix. The process for obtaining the composite was tested against the maximum number of layers that could be used without compromising the processability and manufacturing of CPs in compression mold. Five configurations / formulations were selected and tested at 1, 4, 8, 10 and 12 layers of cotton tissue - TPA. TPA was not subjected to chemical treatment, only by passing a mechanical washing process. The composite in its various configurations / formulations was characterized to determine its physical properties. The properties of the composite were higher viability resistance to bending, approaching the matrix and impact resistance, superiority in relation to the polyester resin. Another property that has shown good result compared to other composite has water absorption. Analyzing all the properties set the settings / formulations with higher viability were TA8 and TA10, by combining good processability and higher mechanical strength, with lower loss compared to polyester resin matrix. The composite showed lower mechanical behavior of the resin matrix for all the formulations studied except the impact resistance. The SEM showed a good adhesion between the layers of TPA and polyester resin matrix, without the presence of micro voids in the matrix confirming the efficient manufacturing process of the samples for characterization. The composite proposed proved to be viable for the fabrication of structures with low requests from mechanical stresses, and as demonstrated for the manufacture of solar and wind prototypes, and packaging, shelving, decorative items, crafts and shelves, with good visual appearance.

Obtenção e caracterização de um compósito polimérico de matriz poliéster e reforço/carga de tecido plano de algodão

He was obtained and studied the feasibility of using TPA (Tissue Cotton Plan) screen type, for bagging, with a weight of 207.9 g / m2 in a composite of orthophthalic crystal polyester resin matrix. The process for obtaining the composite was tested against the maximum number of layers that could be used without compromising the processability and manufacturing of CPs in compression mold. Five configurations / formulations were selected and tested at 1, 4, 8, 10 and 12 layers of cotton tissue - TPA. TPA was not subjected to chemical treatment, only by passing a mechanical washing process. The composite in its various configurations / formulations was characterized to determine its physical properties. The properties of the composite were higher viability resistance to bending, approaching the matrix and impact resistance, superiority in relation to the polyester resin. Another property that has shown good result compared to other composite has water absorption. Analyzing all the properties set the settings / formulations with higher viability were TA8 and TA10, by combining good processability and higher mechanical strength, with lower loss compared to polyester resin matrix. The composite showed lower mechanical behavior of the resin matrix for all the formulations studied except the impact resistance. The SEM showed a good adhesion between the layers of TPA and polyester resin matrix, without the presence of micro voids in the matrix confirming the efficient manufacturing process of the samples for characterization. The composite proposed proved to be viable for the fabrication of structures with low requests from mechanical stresses, and as demonstrated for the manufacture of solar and wind prototypes, and packaging, shelving, decorative items, crafts and shelves, with good visual appearance.

Estudo da obtenção de cerâmica composta de alumina e beta alumina sódica utilizando-se resíduo cerâmico de velas de ignição e pó químico de extintores de incêndio

Ceramic materials the alumina base are large industrial applications. They are required for these products, specific characteristics obtained by following strict criteria during the manufacturing process. However, after life, not always these products are reused by a suitable waste management process. In ceramist context, advance research aimed at the reuse of waste aimed at obtaining ceramics and composite materials, with marked reduction of conventional raw materials. Aiming to generate scientific, technological and environmental contribution, this work studied to obtain a composite of alumina ceramic (Al2O3) and sodium beta alumina (NaAl11O17 ), and as starting materials the residue of the ceramic insulator of spark plugs, as a source alumina (Al2O3) powder and unusable sodium bicarbonate (NaHCO3) of fire extinguishers, as a source of sodium oxide (Na2O). The final ceramic product was obtained from a conventional mixture of sodium aluminum oxide in appropriate molar proportions. Sample spark plugs were obtained, discarded by lifetime, specific to a manufacturer, which, after passing through mechanical stress (grinding, magnetic purification, washing, drying and grinding the high energy), which resulted in residue powder with ceramic content of 84.34 % alumina (Al2O3), found by FRX chemical analysis, the phases present and identified by DRX. The dry chemical fire extinguisher, baking soda-based (NaHCO3) with expired, was obtained through direct collection of the waste generated during maintenance. Subjected to heat treatment at 120 °C , the NaHCO3 powder was decomposed in sodium oxide ( Na2O), which, subjected to chemical analysis (FRX) and mineralogical (DRX) revealed a content of 86.62 % sodium oxide (Na2O) . In the following steps the experimental procedure, chemical formulations were made on a molar basis of the starting material (1:9, 1:10 and 1:11 de Na2O/ Al2O3) inclusion of additives, milling parameters, sieve analysis, dilatometry, conformation of specimens, sintering in firing steps at 800 °C , 1000 °C and 1.200 °C with varying stays 30 , 60 and 120 minutes in each of the levels. The characterization of the final product was made by the following physical tests: water absorption, porosity, linear shrinkage, mineralogical analysis by DRX and microstructural analysis by MEV. A higher formation of sodium beta alumina (NaAl11O17), in sintered specimens in levels of 1.200 °C and 120 minutes, despite the prevailing coexistence of alpha phase alumina (Al2O3). From the results obtained opens up prospects for the reuse of waste studied in this work, the potter context and in other technological areas.

Estudo da obtenção de cerâmica composta de alumina e beta alumina sódica utilizando-se resíduo cerâmico de velas de ignição e pó químico de extintores de incêndio

Ceramic materials the alumina base are large industrial applications. They are required for these products, specific characteristics obtained by following strict criteria during the manufacturing process. However, after life, not always these products are reused by a suitable waste management process. In ceramist context, advance research aimed at the reuse of waste aimed at obtaining ceramics and composite materials, with marked reduction of conventional raw materials. Aiming to generate scientific, technological and environmental contribution, this work studied to obtain a composite of alumina ceramic (Al2O3) and sodium beta alumina (NaAl11O17 ), and as starting materials the residue of the ceramic insulator of spark plugs, as a source alumina (Al2O3) powder and unusable sodium bicarbonate (NaHCO3) of fire extinguishers, as a source of sodium oxide (Na2O). The final ceramic product was obtained from a conventional mixture of sodium aluminum oxide in appropriate molar proportions. Sample spark plugs were obtained, discarded by lifetime, specific to a manufacturer, which, after passing through mechanical stress (grinding, magnetic purification, washing, drying and grinding the high energy), which resulted in residue powder with ceramic content of 84.34 % alumina (Al2O3), found by FRX chemical analysis, the phases present and identified by DRX. The dry chemical fire extinguisher, baking soda-based (NaHCO3) with expired, was obtained through direct collection of the waste generated during maintenance. Subjected to heat treatment at 120 °C , the NaHCO3 powder was decomposed in sodium oxide ( Na2O), which, subjected to chemical analysis (FRX) and mineralogical (DRX) revealed a content of 86.62 % sodium oxide (Na2O) . In the following steps the experimental procedure, chemical formulations were made on a molar basis of the starting material (1:9, 1:10 and 1:11 de Na2O/ Al2O3) inclusion of additives, milling parameters, sieve analysis, dilatometry, conformation of specimens, sintering in firing steps at 800 °C , 1000 °C and 1.200 °C with varying stays 30 , 60 and 120 minutes in each of the levels. The characterization of the final product was made by the following physical tests: water absorption, porosity, linear shrinkage, mineralogical analysis by DRX and microstructural analysis by MEV. A higher formation of sodium beta alumina (NaAl11O17), in sintered specimens in levels of 1.200 °C and 120 minutes, despite the prevailing coexistence of alpha phase alumina (Al2O3). From the results obtained opens up prospects for the reuse of waste studied in this work, the potter context and in other technological areas.

Qualidade dos cuidados em colonoscopia: ansiedade, dor, conforto e satisfação dos utentes

A colonoscopia é o exame preferencial na deteção de patologias do cólon e do reto. Contudo, no nosso país a adesão dos utentes é baixa e isso pode estar relacionado com diversos fatores onde se incluem a ansiedade, a dor e o conforto, importantes focos de atenção dos enfermeiros. Importa que os cuidados de saúde prestados neste âmbito sejam de qualidade, sendo fulcral a avaliação da mesma através da satisfação do utente. Pretendeu-se com este estudo determinar os níveis de ansiedade, dor, conforto e satisfação das pessoas submetidas a colonoscopia, descrever as relações entre as variáveis e compará-las face à utilização de sedação. Pretendeu-se ainda identificar os fatores clínicos e sociodemográficos que interferem nos níveis de ansiedade, dor e conforto. Desenvolveu-se um estudo quantitativo, descritivo e correlacional, através da aplicação de questionários a 60 utentes submetidos a colonoscopia numa instituição de saúde na região de Leiria. Os resultados revelaram a presença de um nível moderado de ansiedade associado à colonoscopia, independentemente de esta ser realizada com sedação. A realização da colonoscopia sem sedação é desencadeadora da dor, que se revelou como um fator inversamente relacionado com a satisfação. Concluímos assim que a colonoscopia é um exame causador de ansiedade, dor e desconforto, onde os enfermeiros podem intervir de forma a aumentar a satisfação com os cuidados.

Temor, silencio y deliberación: la inhibición de la opinión en Tucídides

Tucídides es una de nuestras mejores fuentes de información para conocer la práctica argumentativa de la deliberación democrática. En este trabajo se analiza uno de los vicios que, según el historiador, haría su aparición en la escena política ateniense a la muerte de Pericles: la instrumentalización del miedo para obtener la victoria momentánea en la asamblea. El temor prudente, que fuera una arma periclea para conducir la deliberación racional en aras del bien común, habría desaparecido siendo sustituido por el amedrentamiento del rival, la calumnia, el obstruccionismo y la parálisis de la confrontación dialéctica. Instauradas en la ciudad la desconfianza y la sospecha de ocultación, los golpistas del 411 hallaron el terreno abonado para callar las voces contrarias y, gracias al silencio, instaurar el terror.

The Challenges Faced in Developing Novel Drug Radiation Combinations in Non-small Cell Lung Cancer

Lung cancer is the most common cancer diagnosed in the UK. Outcomes for patients with this disease remain poor and new strategies to treat this disease require investigation. One potential option is to combine novel agents with radiotherapy in clinical studies. Here we discuss some of the important issues to consider when combining novel agents with radiotherapy, together with potential solutions as discussed at a recent Clinical Translational Radiotherapy Group (CTRad) workshop.

Radiotherapy and Immunotherapy Combinations in Non-small Cell Lung Cancer: A Promising Future?

The goal of re-programming the host immune system to target malignancy with durable anti-tumour clinical responses has been speculated for decades. In the last decade such speculation has been transformed into reality with unprecedented and durable responses to immune checkpoint inhibitors seen in solid tumours. This mini-review considers the mechanism of action of immune modulating agents and the potential for combination with radiotherapy in the treatment of non-small cell lung cancer.

Effets préventifs et thérapeutiques des polyphénols dans un modèle in vitro et in vivo de maladie inflammatoire de l’intestin : caractérisation des polyphénols de la pelure de pomme et de la canneberge par spectrométrie de masse

La muqueuse intestinale est exposée à des agents oxydants provenant de l’ingestion d’aliments modifiés, de cellules immuno-inflammatoires et de la flore intestinale. Une diète élevée en fruits et légumes peut diminuer le stress oxydant (SOx) ainsi que l’inflammation via plusieurs mécanismes. Ces effets bénéfiques peuvent être attribuables à leur contenu élevé en polyphénols. La première étude de mon doctorat consistait à tester l’hypothèse que les polyphénols extraits de pelures de pomme (DAPP) pouvaient diminuer le stress oxydant et l'inflammation impliqués dans les maladies inflammatoires de l'intestin (MII). Nous avons caractérisé les polyphénols des DAPP par spectrométrie de masse (LC-MS) et examiné leur potentiel antioxydant et anti-inflammatoire au niveau des cellules intestinales. L’identification des structures chimiques des polyphénols a été effectuée par LC-MS. Le SOx a été induit par l’ajout du complexe fer/ascorbate (Fe/Asc, 200 µM/2 mM) et l’inflammation par la lipopolysaccharide (LPS, 200µg/mL) à des cellules intestinales Caco-2/15 pré-incubées avec les DAPP (250 µg/mL). L’effet du SOx est déterminé par le dosage du malondialdéhyde (MDA), de la composition des acides gras polyinsaturés et de l’activité des enzymes antioxydantes endogènes (SOD et GPx). L’impact des DAPP sur l’inflammation a été testé par l’analyse de l’expression des marqueurs inflammatoires: cyclooxygénase-2 (COX-2), le facteur de nécrose tumorale alpha (TNF-a et l’interleukine-6 (IL-6) et les facteurs de transcription NF-KB, Nrf-2 et PGC1α par immunobuvardage. Nos données ont montré que les flavonols et les flavan-3-ols constituent les composés polyphénoliques majoritaires des DAPP. L’ajout de Fer2+/Asc a provoqué une augmentation de la peroxidation lipidique comparativement aux cellules contrôles, un appauvrissement des acides gras polyinsaturés n-3 et n-6, et une modulation des enzymes antioxydantes, se traduisant par une augmentation de l’activité de la SOD et une diminution de la GPx. En contrepartie, les DAPP ont exhibé leur potentiel à corriger la plupart des perturbations, y compris l’expression protéique anormalement élevée du COX-2 et la production de la prostaglandine E2 (PGE2), ainsi que l’inflammation telle que réflétée par les facteurs NF-κB, TNF-α et IL-6. Par ailleurs, les mécanismes sous-jacents à ces changements bénéfiques des DAPP ont fait intervenir les facteurs de transcription antioxydants (Nrf-2, PGC1α). Vraisemblablement, cette première étude a permis de démontrer la capacité des DAPP à amoindrir le SOx et à réduire l’inflammation, deux processus étroitement impliqués dans les MII. Dans la deuxième étape de mon doctorat, nous avons voulu comparer les résultats de DAPP à ceux des polyphénols dérivant de la canneberge qui est considérée par la communauté scientifique comme le fruit ayant le plus fort potentiel antioxydant. À cette fin, nous avons caractérisé l’effet des composés polyphénoliques de la canneberge (CPC) sur le SOx, la défense antioxydante et l’inflammation au niveau intestinal tout en définissant leur métabolisme intraluminal. Les différents CPC ont été séparés selon leur poids moléculaire par chromatographie et leurs structures chimiques ont été identifiées par LC-MS. Suite à une pré-incubation des cellules Caco-2/15 avec les extraits CPC (250 µg/mL), le Fe/Asc et la LPS ont été administrés comme inducteurs du SOx et de l’inflammation, respectivement. La caractérisation globale des CPC a révélé que les acides phénoliques composaient majoritairement l’extrait de canneberge de petit poids moléculaire (LC) alors que les flavonoïdes et les procyanidines dimériques/trimériques représentaient l’extrait de poids moléculaire moyen (MC) tout en laissant les procyanidines oligo et polymériques à l’extrait de haut poids moléculaire (HC). Les CPC ont permis de restaurer la plupart des perturbations engendrées dans les Caco-2/15 par le Fe/Asc et le LPS. Les CPC exhibaient le potentiel d’abaisser les niveaux de MDA, de corriger la composition des acides gras polyinsaturés n-3 et n-6, d’augmenter l’activité des enzymes antioxydantes (SOD, GPx et CAT) et d’élever l’expression de Nrf2 et PGC1α. En outre, les CPC pouvaient aussi réduire les niveaux élevés des protéines inflammatoires COX-2, TNF-α et IL-6 ainsi que la production des PGE2 par un mécanisme impliquant le NF-κB. Au niveau mitochondrial, les procyanidines oligomériques ont réussi à corriger les dysfonctions reliées à la production d’énergie (ATP), l’apoptose (Bcl-2, Cyt C et AIF) et le statut des facteurs de transcription mitochondriaux (mtTFA, mtTFB1, mtTFB2). Dans le but de bien comprendre les mécanismes d’action des CPC, nous avons défini par LC-MS les composés polyphénoliques qui ont été transportés ou absorbés par l’entérocyte. Nos analyses soulignent le transport (i) des acides cinnamiques et benzoïques (LC); (ii) la quercétine glycosylée et conjuguée et les procyanidines dimériques de type A (MC); et (iii) l’épicatéchine et les procyanidines oligomériques (HC). Les processus de métabolisation (méthylation, glucuronidation et sulfatation) au niveau de l’entérocyte ont probablement permis le transport de ces CPC surtout sous leur forme conjuguée. Les procyanidines oligomériques ayant un degré de polymérisation supérieur à 2 (HC) ont semblé adhérer aux cellules Caco-2/15. L’épicatéchine suivi par les procyanidines dimériques de type A ont été trouvés majoritaires au niveau des mitochondries. Même si nous ignorons encore l’action biologique de chaque composé polyphénolique, nous pouvons suggérer que leurs effets combinatoires exercent des fonctions antioxydantes, anti-inflammatoires et mitochondriales dans le modèle intestinal Caco-2/15. Dans une troisième étape, nous avons procédé à l’évaluation des aspects préventifs et thérapeutique des DAPP tout en sondant les mécanismes sous-jacents dans une étude préclinique. À cette fin, nous avons exploité le modèle de souris avec colite expérimentale provoquée par le Dextran Sulfate de Sodium (DSS). L’induction de l’inflammation intestinale chez la souris C57BL6 a été effectuée par l’administration orale de DSS à 2.5% pendant 10 jours. Des doses physiologiques et supra-physiologiques de DAPP (200 et 400 mg/kg/j, respectivement) ont été administrées par gavage pendant 10 jours pré- et post-DSS. L’inflammation par le DSS a provoqué une perte de poids, un raccourcissement du côlon, le décollement dystrophique de l’épithélium, l’exulcération et les infiltrations de cellules mono et polynucléaires au niveau du côlon. De plus, le DSS a induit une augmentation de la peroxidation lipidique, une régulation à la baisse des enzymes antioxydantes, une expression protéique à la hausse de la myéloperoxidase (MPO), du COX-2 et de la production des PGE2. Par ailleurs, les DAPP ont permis de corriger ou du moins d’alléger la plupart de ces anomalies en situation préventive ou thérapeutique, en plus d’abaisser l’expression protéique de NF-κB et des cytokines inflammatoires (TNF-a et l’IL-6) tout en stimulant les facteurs de transcription antioxydants (Nrf-2, PGC1α). Conséquemment, les polyphénols des DAPP ont exhibé leur puissant pouvoir antioxydant et anti-inflammatoire au niveau intestinal dans un modèle in vivo. Leurs actions sont associées à la régulation des voies de signalisation cellulaire et des changements dans la composition du microbiote. Ces trois projets de recherche permettent d’envisager l’évaluation des effets préventifs et thérapeutiques des DAPP cliniquement chez les patients avec des désordres inflammatoires de l’intestin.

Colite de derivação fecal

A colite de derivação fecal (CD) é um processo inflamatório que ocorre no segmento colorretal desfuncionalizado, após uma cirurgia de desvio do trânsito intestinal. As principais características dessa entidade clínica são: apresenta-se na desfuncionalização do cólon ou reto; não há doença inflamatória intestinal preexistente; nunca acomete o sítio proximal à colostomia e ocorre resolução do processo após a restauração do trânsito intestinal. Diversas são as hipóteses postuladas para explicar o seu aparecimento; todavia, a deficiência nutricional do epitélio colônico, pela ausência dos ácidos graxos de cadeia curta (AGCC), no segmento desfuncionalizado, é a mais aceita na atualidade. Os autores fazem uma revisão da literatura enfocando os aspectos clínicos, histopatológicos e terapêuticos desta doença

Repercussões histopatológicas da colostomia no coto colônico distal desfuncionalizado: estudo experimental em ratos

O objetivo deste trabalho foi evidenciar as repercussões histopatológicas da colostomia no segmento desfuncionalizado e, dessa forma, criar um modelo experimental da colite de derivação fecal (CO). Foram utilizados 65 ratos, adultos, da raça Wistar, com peso variando de 220 a 300 g. Os animais foram divididos em 13 grupos, contendo cinco ratos. Do grupo 1 ao grupo 12, os animais foram submetidos a laparotomia mediana, sendo realizada uma colostomia terminal tipo boca única, e observados, por períodos variados de tempo, com o máximo de cem dias. Os animais, após serem mortos, foram necropsiados e retirado o segmento co1ônico desfuncionalizado para a avaliação histopatológica. Essa avaliação consistia de uma análise quantitativa, através da medida da espessura da mucosa colônica, e de uma análise qualitativa, mediante avaliação subjetiva: da presença de infiltrado inflamatório agudo ou crônico na lâmina própria; das alterações na arquitetura das criptas colônicas; da presença de hiperplasia folicular linfóide e de linfócitos na luz dos vasos da submucosa; e da presença de eosinófilos na luz intestinal. No grupo 12, após o 100° dia de pós-operatório (OPO), foi realizada a reconstrução do trânsito intestinal, e, após trinta dias, o cólon descendente foi retirado para a análise histopatológica. O método de Tukey e o teste "t" de Student foram utilizados como parte da análise dos resultados. Verificou-se uma redução estatisticamente significante da espessura da mucosa colônica a partir do 4000PO. Concluiu-se que a colostomia desfuncionalizante realizada em ratos reproduziu alterações histopatológicas compatíveis com a colite de derivação, e que estas mostraram-se reversíveis após a reconstrução do trânsito intestinal