Tendencias actuales y perspectivas de las comunicaciones ópticas

A short review to the main problems today in optical Communications is given. Several topics, namely, coherent optical systems, high-speed transmission systems, optical switching, fluoride glasses and wavelength division multiplexing are studied. Their status and future is reported. Some considerations coming out from the next ECOC'88, give way to the author impresions about the present and future of Optical Communications.

Advances on MBE selective area growth of III-nitride nanostructures: from nanoLEDs to pseudo substrates

The aim of this work is to provide an overview on the recent advances in the selective area growth (SAG) of (In)GaN nanostructures by plasma assisted molecular beam epitaxy, focusing on their potential as building blocks for next generation LEDs. The first three sections deal with the basic growth mechanisms of GaN SAG and the emission control in the entire ultraviolet to infrared range, including approaches for white light emission, using InGaN disks and thick segments on axial nanocolumns. SAG of axial nanostructures is eveloped on both GaN/sapphire templates and GaN-buffered Si(111). As an alternative to axial nanocolumns, section 4 reports on the growth and characterization of InGaN/GaN core-shell structures on an ordered array of top-down patterned GaN microrods. Finally, section 5 reports on the SAG of GaN, with and without InGaN insertion, on semi-polar (11-22) and non-polar (11-20) templates. Upon SAG the high defect density present in the templates is strongly reduced as indicated by a dramatic improvement of the optical properties. In the case of SAG on nonpolar (11-22) templates, the formation of nanostructures with a low aspect ratio took place allowing for the fabrication of high-quality, non-polar GaN pseudo-templates by coalescence of these nanostructures.

Numerical Simulation of the Aerodynamic Behavior of High Velocity Trains under Synthetic Crosswinds of Different Shear and Turbulence Characteristics

A numerical simulation of the aerodynamic behavior of high-speed trains under synthetic crosswinds at a 90º yaw angle is presented. The train geometry is the aerodynamic train model (ATM). Flow description based on numerical simulations is obtained using large eddy simulation (LES) and the commercial code ANSYSFluent V14.5. A crosswind whose averaged velocity and turbulence characteristics change with distance to the ground is imposed. Turbulent fluctuations that vary temporally and spatially are simulated with TurbSim code. The crosswind boundary condition is calculated for the distance the train runs during a simulation period. The inlet streamwise velocity boundary condition is generated using Taylor?s frozen turbulence hypothesis. The model gives a time history of the force and moments acting on the train; this includes averaged values, standard deviations and extreme values. Of particular interest are the spectra of the forces and moments, and the admittance spectra. For comparison, results obtained with LES and a uniform wind velocity fluctuating in time, and results obtained with Reynolds averaged Navier Stokes equations (RANS), and the averaged wind conditions, are also presented.

Regulación del movimiento y anticipación en el resto del primer servicio en tenis

Aunque se han logrado importantes avances en estudios de laboratorio con diseños experimentales poco representativos (e.g., Farrow y Reid, 2012; Nieminen, Piirainen, Salmi, y Linnamo, 2013), a día de hoy, todavía se desconoce a cabalidad cómo los jugadores de tenis de diferente nivel de pericia calibran o ajustan sus movimientos a las demandas espacio-temporales presentes en la tarea de resto de un primer servicio. ! Escasos trabajos se han llevado a cabo in situ y a la mayoría se les puede cuestionar algún aspecto de la metodología empleada. Así pues, en varios estudios la frecuencia de grabación ha sido limitada (e.g., a 50 Hz en Jackson y Gudgeon, 2004; Triolet, Benguigui, Le Runigo y Williams, 2013), o la velocidad del saque ha sido visiblemente inferior a la habitual (cf. Carboch, Süss y Kocib, 2014; Williams, Singer y Weigelt, 1998). También, en algunos estudios los participantes experimentados no han sido jugadores de nivel internacional (e.g., Avilés, Ruiz, Sanz y Navia, 2014), y el tamaño muestral ha sido muy pequeño (e.g., Gillet, Leroy, Thouvarecq, Mégrot y Stein, 2010). ! Además, en los diferentes trabajos se han utilizado una diversidad de métodos e instrumentos de medida y los criterios de codificación del inicio de los movimientos y de las respuestas han diferido; como consecuencia el lapso visomotor de respuesta (LVMr) ha sido muy dispar variando considerablemente de 198 a 410 ms. Considerando los inconvenientes señalados anteriormente, el presente estudio tuvo como objetivo determinar un modelo técnico de regulación temporal de los movimientos y de la respuesta del restador, tomando en cuenta el flujo continuo de información proporcionado por el sacador. Para ello, se realizó un análisis cronométrico de los restos de doce jugadores de diferente nivel deportivo (seis internacionales y seis nacionales) que respondieron de forma natural enviando sus devoluciones hacia las dianas. Se grabaron las acciones de los restadores y sacadores con una cámara Casio Exilim Pro Ex-F1 de alta velocidad (300 Hz) y luego se realizó un análisis imagen por imagen cada 3.33 ms. Una vez obtenidos los datos de los vídeos se realizaron análisis con las pruebas de ANOVA de un factor, ANCOVA con la velocidad del saque como covariable, U de Mann-Whitney y Chi-cuadrado de Pearson. En cuanto a la regulación del movimiento hasta el momento del despegue, los jugadores internacionales iniciaron sus acciones antes que los jugadores nacionales lo que podría indicar una mejor preparación al ejecutar los movimientos como reflejo del nivel de pericia. Los jugadores internacionales iniciaron la elevación del pie posterior a -293 ms y los jugadores nacionales a -202 ms. Todas estas acciones se fueron enlazando unas con otras y fue en el momento del impacto del sacador donde los restadores demostraron una remarcable coordinación perceptivo-motriz. Por consiguiente, los jugadores internacionales despegaron e iniciaron el vuelo a tan solo -6.5 ms del impacto y los jugadores nacionales lo hicieron más tarde a +19.5 ms. A lo largo de la secuencia temporal, todo parece indicar que las informaciones que utilizan los restadores interactúan entre sí; información más temprana y menos fiable para anticipar o moverse antes e información más tardía y más fiable para regular la temporalización de las acciones. Los restadores de nivel internacional y nacional anticiparon a nivel espacial en un bajo porcentaje (7.7% vs. 13.6%) y en tiempos similares (-127 vs. -118 ms) sugiriendo que la utilización de variables ópticas tempranas y menos fiables solo se produce en contadas ocasiones. Por otra parte, estos datos se relacionan con una gran precisión en la respuesta ya que tanto los jugadores internacionales como los nacionales demostraron un alto porcentaje de acierto al responder (95.4% vs. 96.7%). Se había señalado que los jugadores internacionales y nacionales se diferenciarían en el tiempo de caída (i.e., aterrizaje) del primer pie del salto preparatorio, sin embargo ese efecto no fue encontrado (128 vs. 135 ms). Tampoco se hallaron diferencias en el porcentaje de caída con el pie contrario a la dirección de la pelota (58% vs. 62%). Donde sí ambos grupos se diferenciaron fue en el tiempo de caída del segundo pie (147 vs. 168 ms). Esta diferencia de 21 ms fue crucial y fue una prueba de la mayor rapidez de los jugadores internacionales; sugiriendo que ésta acción se podría relacionar con el momento del inicio de la respuesta. Aunque los jugadores internacionales hayan demostrado ser más rápidos en relación con sus capacidades funcionales, ambos grupos no se diferenciaron en todas las variables relacionadas con el LVMr. Ellos no utilizaron esos valiosos milisegundos ganados en el instante de la caída del segundo pie para responder más pronto, ya que el LVMr del miembro superior fue el mismo para ambos grupos (179 vs. 174 ms). Es como si hubiesen tenido todo el tiempo del mundo para seguir ajustando sus acciones hasta el propio golpeo. Además, estos tiempos largos sugieren que en la gran mayoría de los restos la información clave que determinó la respuesta fue detectada (extraída) en momentos cercanos al golpeo del sacador y en la primera parte del vuelo de la pelota. Asimismo, se constató que en general el LVMr se ve influenciado por el tipo de información utilizada. De esta manera, cuando se tomaron en cuenta los ensayos en los que hubo anticipación espacial reflejados en el LVMr del cuerpo entero los tiempos disminuyeron (152 vs. 136 ms). Por otra parte, existieron ocasiones (13%) en los que tanto los jugadores internacionales como los nacionales respondieron tarde recibiendo saques directos (208 vs. 195 ms). Es muy posible que en estos casos los jugadores hayan tenido problemas para detectar la información respondiendo fuera de los márgenes temporales de acción lo que mermó su rendimiento. Lo mismo pudo haber ocurrido cuando ambos grupos de jugadores corrigieron el movimiento del miembro superior tras el impacto (17% vs. 10%) lo que aumentó el tiempo en responder al redirigir la respuesta hacia el lado correcto (208 vs. 205 ms). Además, los jugadores internacionales obtuvieron tiempos de movimiento menores que el de los jugadores nacionales (509 vs. 531 ms) lo que se reflejó en un tiempo total de actuación menor (683 vs. 703 ms). Por último, en cuanto al rendimiento del resto, los jugadores internacionales obtuvieron valores superiores a los jugadores nacionales (1.3 vs. 0.9). ABSTRACT Although there have been significant advances in laboratory studies with unrepresentative experimental designs (e.g., Farrow y Reid, 2012; Nieminen, Piirainen, Salmi, y Linnamo, 2013), today it is still unknown to full extent how tennis players of different levels of expertise calibrate or adjust their movements to the spatial-temporal demands present in the return of a first serve. Few studies have been carried out in situ and some aspects of the methodology most of them used can be questioned. Thus, in several studies the recording frequency has been limited (e.g., a 50 Hz en Jackson y Gudgeon, 2004; Triolet, Benguigui, Le Runigo y Williams, 2013), or serve speed was visibly lower than the usual one (cf. Carboch, Süss y Kocib, 2014; Williams, Singer y Weigelt, 1998). Also, in some studies, experienced participants have not played at international level (e.g., Avilés, Ruiz, Sanz y Navia, 2014), and the sample size has been very small (e.g., Gillet, Leroy, Thouvarecq, Mégrot y Stein, 2010). Furthermore, different works have used a variety of methods and measurement instruments and coding criteria of the onset of movements and responses have differed; due to this, visuomotor response delay (LVMr) has been very uneven, varying considerably from 198-410 ms. Considering the drawbacks mentioned above, this study aimed to determine a technical model of temporal regulation of movements and returner’s response, taking into account the continuous flow of information provided by the server. For this, a chronometric analysis of the returns of twelve players (six international and six national) of different sports level, that naturally responded by hitting their returns towards the targets, was performed. Actions of servers and returners were recorded with a Casio Exilim Pro Ex-F1 high speed camera (300 Hz) and then every 3.33 ms analysis was made frame by frame. Once the data of the videos were obtained, analyses were performed using one factor ANOVA test, ANCOVA with the speed of the serve as a covariate, U of Mann- Whitney and Pearson’s Chi-square test. As for the regulation of movement until the moment of serve, international players began their actions before national players, which could indicate that they were better prepared to execute movements reflecting the level of their expertise. International players began raising the rear foot at -293 ms and national players at -202 ms. All these actions were being linked to each other and it was at the moment of impact of the server when the receivers demonstrated a remarkable perceptual-motor coordination. Therefore, international players took off and started their flight just -6.5 ms before the serve and national players did the same somewhat later: +19.5 ms after the serve. Along the timeline, everything seems to indicate that the information used by returners interact with each other; early information which is less reliable to anticipate or move before, and later information more reliable appears to regulate the timing of actions. Returners of international and national levels anticipated at spatial level in a low percentage (7.7% vs. 13.6%) and in similar times (-127 vs. -118 ms) suggesting that the use of early and less reliable optical variables is only produced on rare occasions. Moreover, these data relate to a precise response as both international and national players showed a high percentage of success in responding (95.4% vs. 96.7%). It had been noted that international and national players would differ in the time the fall (i.e., landing) of the first foot of the split-step, however, this effect was not found (128 vs. 135 ms). No differences in the percentage of fall with the opposite foot to the direction of the ball (58% vs. 62%) were found. Where the two groups differed was in the time of the fall of the second foot (147 vs. 168 ms). This difference of 21 ms was crucial and it was a proof of mayor speed of international players; suggesting that this action could be related to the onset time of response. Although international players have proven to be faster in relation to their functional capabilities, both groups did not differ in all variables related to LVMr. They did not use those precious milliseconds earned at the time of the fall of the second foot to respond as soon, since the LVMr of the upper limb was the same for both groups (179 vs. 174 ms). It is as if they had all the time in the world to continue to adjust their actions until the return itself. Furthermore, these long times suggest that in the vast majority of the returns, key information that determined the response was detected (pick-up) in moments close to the hit of the server and in the first part of the ball flight. It was also found that in general the LVMr is influenced by the type of information used. Thus, when taking into account the trials during which there was spatial anticipation, reflected in LVMr of the whole body, the times decreased (152 vs. 136 ms). On the other hand, there were occasions (13%) where both international and national players responded late, thus receiving aces (208 vs. 195 ms). It is quite possible that in these cases the players have had trouble to pick-up information, responding out of temporary margins of action, which affected their performance. The same could have occurred when both groups of players corrected upper limb movement after impact (17% vs. 10%), which increased the time to respond and to redirect the return towards the right side (208 vs. 205 ms). Moreover, international players scored lower movement times than the national players (509 vs. 531 ms), which was reflected in a shorter total response time (683 vs. 703 ms). Finally, as far as the performance of return is concerned, international players scored above the national players values (1.3 vs. 0.9).

Planificación de una red 4G

La intensa evolución tecnológica que está experimentando nuestra sociedad en las últimas décadas hace que se estén desarrollando continuamente nuevas tecnologías que proporcionan mejoras tanto en la calidad como en la seguridad del servicio, este es el caso del 4G. A día de hoy, en España, la cuarta generación de comunicaciones móviles se ve encabezada por LTE, mientras que LTE-Advanced sólo se está implantando en las principales ciudades de nuestro país durante los últimos meses. Por este motivo, se ha creído interesante realizar una planificación sobre una zona que, hasta el momento, no está cubierta por cobertura LTE-Advanced. Además hay que tener en cuenta la naturaleza del terreno en el que trabajaremos, ya que se aleja del suelo urbano que encontramos en las principales ciudades con LTE-Advanced, como Madrid, Barcelona o Valencia. El estudio de esta zona semirural es de gran interés ya que uno de los objetivos de la cuarta generación es hacer llegar conexión a internet de calidad a lugares en los que no puede llegar la fibra óptica, como por ejemplo estas zonas semirurales. Para añadir aún más interés en el estudio, se ha decidido utilizar la banda de 800 MHz para el despliegue de la red. Esta banda que anteriormente era utilizada para la transmisión TDT, recientemente ha quedado liberada, en el conocido como Dividendo Digital para su uso en comunicaciones móviles. La tecnología LTE-Advanced se está empezando a desplegar en esta banda aunque realmente hasta Noviembre del año 2015 no tendremos un uso real de la misma, por lo que en estos momentos las redes 4G están utilizando la banda de 2.6 GHz. La utilización de la banda de 800 MHz conllevará mejoras tanto al usuario como a las operadoras, las cuales iremos viendo a lo largo del desarrollo del proyecto. La planificación pasará por distintas fases de optimización y expansión en las que se analizaran tanto la parte radioeléctrica como su capacidad. Se analizaran señales del tipo RSRP, RSSI o RSRQ y para el análisis de capacidad se definirá un conjunto de usuarios, distribuidos adecuadamente por toda la zona, que permitirá estudiar en detalle la capacidad de nuestra red. Para finalizar, se realizarán varias pruebas que demostrarán lo importante que es la tecnología MIMO tanto en LTE como en LTE-Advanced. ABSTRACT. Nowadays, our society is experiencing an intense pace of technological evolution which causes the constant development of new technologies. In the network planning area, these new technologies are focused on improving both quality and safety of service, with the recent deployment of 4G technologies in our networks. This project focuses on Spain, where the fourth generation of mobile communications is led by LTE, because LTE-Advanced has only been deployed in the largest cities, so far. The goal of this project is to plan, deploy and simulate LTE-Advanced network, of an area that hasn´t yet been covered. Furthermore, it will be taken into account the nature of the terrain where the network will be developed, as it moves away from urban areas in the major cities with LTE-Advanced, including Madrid, Barcelona and Valencia. The study of these semi-rural areas is extremely important because one of the main objectives of the fourth generation technologies is to get high-speed internet access to places that can be reached through other technologies, such as optical fiber. In order to adjust to the actual needs, the project was developed for the 800 MHz band. Those frequencies used to be assigned for digital terrestrial TV, but they have recently been released through the Digital Dividend in 2015 to use with mobile communications. That is the reason why, the LTE-Advanced technology in Spain is starting to be deployed in those frequencies. Despite the freeing of the 800 MHz band, it is not allowed to use it until November 2015, so 4G networks are currently using the 2.6 GHz band. The use of the 800 MHz band will led to advantages and improvements to users and operators, which will be detailed over the project. Each step of the planning of the 4G network is detailed. It is analyzed the optimization and expansion of the network, based on the radio and capacity premises. RSRP, RSSI or RSRQ signals were analyzed and an analysis of the network capacity was carried out. Finally, several tests are developed to show the importance of MIMO in LTE and LTE-Advanced.

Contribution to the analysis and design of reflectarray antennas for reconfigurable beam applications at frequencies above 100 GHz using liquid crystal technology

El trabajo contenido en esta tesis doctoral está encuadrado en el desarrollo de antenas reconfigurables electrónicamente capaces de proporcionar prestaciones competitivas a las aplicaciones cada vez más comunes que operan a frecuencias superiores a 60 GHz. En concreto, esta tesis se centra en el estudio, diseño, e implementación de las antenas reflectarray, a las que se introduce la tecnología de cristal líquido como elemento característico con el que se consigue reconfigurabilidad de haz de forma electrónica. Desde un punto de vista muy general, se puede describir un cristal líquido como un material cuya permitividad eléctrica es variable y controlada por una excitación externa, que generalmente suele corresponderse con un campo eléctrico quasi-estático (AC). Las antenas reflectarray de cristal líquido se han escogido como objeto de estudio por varias razones. La primera de ellas tiene que ver con las ventajas que los reflectarrays, y en especial aquellos realizados en configuración planar, proporcionan con respecto a otras antenas de alta ganancia como los reflectores o los “phased-arrays”. En los reflectarrays, la alimentación a través de una fuente primaria común (característica de reflectores) y el elevado número de grados de libertad de las celdas que los componen (característica de arrays) hacen que estas antenas puedan proporcionar prestaciones eléctricas iguales o mejores que las anteriores, a un coste más reducido y con estructuras de antena más compactas. La segunda razón radica en la flexibilidad que ofrece el cristal líquido a ser confinado y polarizado en recintos de geometría variada, como consecuencia de su fluidez (propiedad de los líquidos). Por ello, la tecnología de cristal líquido permite que el propio elemento reconfigurable en las celdas de reflectarray se adapte a la configuración planar de manera que en sí mismo, el cristal líquido sea una o varias de las capas características de esta configuración. Esto simplifica de forma drástica la estructura y la fabricación de este tipo de antenas, incluso si se comparan con reflectarrays reconfigurables basados en otras tecnologías como diodos, MEMS, etc. Por tanto, su coste y desarrollo es muy reducido, lo que hace que se puedan fabricar reflectarrays reconfigurables eléctricamente grandes, a bajo coste, y en producción elevada. Un ejemplo claro de una estructura similar, y que ha tenido éxito comercial, son las pantallas de cristal líquido. La tercera razón reside en el hecho de que el cristal líquido es, hasta la fecha, de las pocas tecnologías capaces de ofrecer reconfigurabilidad del haz a frecuencias superiores a 60 GHz. De hecho, el cristal líquido permite reconfigurabilidad en un amplio margen de frecuencias, que va desde DC a frecuencias del espectro visible, incluyendo las microondas y los THz. Otras tecnologías, como los materiales ferroeléctricos, el grafeno o la tecnología CMOS “on chip” permiten también conmutar el haz en estas frecuencias. Sin embargo, la tecnología CMOS tiene un elevado coste y actualmente está limitada a frecuencias inferiores a 150 GHz, y aunque los materiales ferroeléctricos o el grafeno puedan conmutar a frecuencias más altas y en un rango más amplio, tienen serias dificultades que los hacen aún inmaduros. En el caso de los materiales ferroeléctricos, los elevados voltajes para conmutar el material los hacen poco atractivos, mientras que en el caso del grafeno, su modelado aún está en discusión, y todavía no se han arrojado resultados experimentales que validen su idoneidad. Estas tres razones hacen que los reflectarrays basados en cristal líquido sean atractivos para multitud de aplicaciones de haz reconfigurable a frecuencias superiores a 60 GHz. Aplicaciones como radar de escaneo de imágenes de alta resolución, espectroscopia molecular, radiómetros para observación atmosférica, o comunicaciones inalámbricas de alta frecuencia (WiGig) son algunas de ellas. La tesis está estructurada en tres partes. En la primera de ellas se describen las características más comunes de los cristales líquidos, centrándonos en detalle en aquellas propiedades ofrecidas por este material en fase nemática. En concreto, se estudiará la anisotropía dieléctrica (Ae) de los cristales líquidos uniaxiales, que son los que se emplean en esta tesis, definida como la diferencia entre la permitividad paralela (£//) y la perpendicular (e±): Ae = e,, - e±. También se estudiará la variación de este parámetro (Ae) con la frecuencia, y el modelado electromagnético macroscópico más general que, extraído a partir de aquella, permite describir el cristal líquido para cada tensión de polarización en celdas de geometría planar. Este modelo es de suma importancia para garantizar precisión en el desfasaje proporcionado por las diferentes celdas reconfigurables para reflectarrays que se describirán en la siguiente parte de la tesis. La segunda parte de la tesis se centra en el diseño de celdas reflectarray resonantes basadas en cristal líquido. La razón por la que se escogen estos tipos de celdas reside en el hecho de que son las únicas capaces de proporcionar rangos de fase elevados ante la reducida anisotropía dieléctrica que ofrecen los cristales líquidos. El objetivo de esta parte trata, por tanto, de obtener estructuras de celdas reflectarray que sean capaces de proporcionar buenas prestaciones eléctricas a nivel de antena, mejorando sustancialmente las prestaciones de las celdas reportadas en el estado del arte, así como de desarrollar una herramienta de diseño general para aquellas. Para ello, se estudian las prestaciones eléctricas de diferentes tipos de elementos resonantes de cristal líquido que van, desde el más sencillo, que ha limitado el estado de la técnica hasta el desarrollo de esta tesis y que está formado por un sólo resonador, a elementos que constan de varios resonadores (multi-resonantes) y que pueden ser monocapa o multicapa. En un primer paso, el procedimiento de diseño de estas estructuras hace uso de un modelo convencional de cristal líquido que ha venido siendo usado en el estado del arte para este tipo de celdas, y que considera el cristal líquido como un material homogéneo e isótropo cuya permitividad varía entre (e/7) y (e±). Sin embargo, en esta parte de la tesis se demuestra que dicho modelado no es suficiente para describir de forma genérica el comportamiento del cristal líquido en las celdas tipo reflectarray. En la tesis se proponen procedimientos más exactos para el análisis y diseño basados en un modelo más general que define el cristal líquido como un material anisótropo e inhomogeneo en tres dimensiones, y se ha implementado una técnica que permite optimizar celdas multi-resonantes de forma eficiente para conseguir elevadas prestaciones en cuanto a ancho de banda, rango de fase, pérdidas, o sensibilidad al ángulo de incidencia. Los errores cometidos en el uso del modelado convencional a nivel de celda (amplitud y fase) se han analizado para varias geometrías, usando medidas de varios prototipos de antena que usan un cristal líquido real a frecuencias superiores a 100 GHz. Las medidas se han realizado en entorno periódico mediante un banco cuasi-óptico, que ha sido diseñado especialmente para este fin. Uno de estos prototipos se ha optimizado a 100 GHz para conseguir un ancho de banda relativamente elevado (10%), pérdidas reducidas, un rango de fase mayor de 360º, baja sensibilidad al ángulo de incidencia, y baja influencia de la inhomogeneidad transversal del cristal líquido en la celda. Estas prestaciones a nivel de celda superan de forma clara aquellas conseguidas por otros elementos que se han reportado en la literatura, de manera que dicho prototipo se ha usado en la última parte de la tesis para realizar diversas antenas de barrido. Finalmente, en esta parte se presenta una estrategia de caracterización de la anisotropía macroscópica a partir de medidas de los elementos de reflectarray diseñados en banco cuasi-óptico, obteniendo resultados tanto en las frecuencias de interés en RF como en AC, y comparándolas con aquellas obtenidas mediante otros métodos. La tercera parte de la tesis consiste en el estudio, diseño, fabricación y medida de antenas reconfigurables basadas en cristal líquido en configuraciones complejas. En reflectarrays pasivos, el procedimiento de diseño de la antena se limita únicamente al ajuste en cada celda de la antena de las dimensiones de las metalizaciones que se emplean para el control de fase, mediante procesos de optimización bien conocidos. Sin embargo, en el caso de reflectarrays reconfigurables basados en cristal líquido, resulta necesario un paso adicional, que consiste en calcular de forma adecuada las tensiones de control en cada celda del reflectarray para configurar la fase requerida en cada una de ellas, así como diseñar la estructura y los circuitos de control que permitan direccionar a cada elemento su tensión correspondiente. La síntesis de tensiones es por tanto igual o más importante que el diseño de la geometría de las celdas, puesto que éstas son las que están directamente relacionadas con la fase. En el estado del arte, existen varias estrategias de síntesis de tensiones que se basan en la caracterización experimental de la curva de fase respecto al voltaje. Sin embargo, esta caracterización sólo puede hacerse a un solo ángulo de incidencia y para unas determinadas dimensiones de celda, lo que produce que las tensiones sintetizadas sean diferentes de las adecuadas, y en definitiva que se alcancen errores de fase mayores de 70º. De esta forma, hasta la fecha, las prestaciones a nivel de antena que se han conseguido son reducidas en cuanto a ancho de banda, rango de escaneo o nivel de lóbulos secundarios. En esta última parte de la tesis, se introduce una nueva estrategia de síntesis de tensiones que es capaz de predecir mediante simulaciones, y con alta precisión, las tensiones que deben introducirse en cada celda teniendo en cuenta su ángulo de incidencia, sus dimensiones, la frecuencia, así como la señal de polarización definida por su frecuencia y forma de onda AC. Esta estrategia se basa en modelar cada uno de los estados de permitividad del cristal líquido como un sustrato anisótropo con inhomogeneidad longitudinal (1D), o en ciertos casos, como un tensor equivalente homogéneo. La precisión de ambos modelos electromagnéticos también se discute. Con el objetivo de obtener una herramienta eficiente de cálculo de tensiones, también se ha escrito e implementado una herramienta de análisis basada en el Método de los Momentos en el Dominio Espectral (SD-MoM) para sustratos estratificados anisótropos, que se usa en cada iteración del procedimiento de síntesis para analizar cada una de las celdas de la antena. La síntesis de tensiones se ha diseñado además para reducir al máximo el efecto del rizado de amplitud en el diagrama de radiación, que es característico en los reflectarrays que están formados por celdas con pérdidas elevadas, lo que en sí, supone un avance adicional para la obtención de mejores prestaciones de antena. Para el cálculo de los diagramas de radiación empleados en el procedimiento de síntesis, se asume un análisis elemento a elemento considerando periodicidad local, y se propone el uso de un método capaz de modelar el campo incidente de forma que se elimine la limitación de la periodicidad local en la excitación. Una vez definida la estrategia adecuada de cálculo de las tensiones a aplicar al cristal líquido en cada celda, la estructura de direccionamiento de las mismas en la antena, y diseñados los circuitos de control, se diseñan, fabrican y miden dos prototipos diferentes de antena de barrido electrónico a 100 GHz usando las celdas anteriormente presentadas. El primero de estos prototipos es un reflectarray en configuración “single offset” con capacidad de escaneo en un plano (elevación o azimut). Aunque previamente se realizan diseños de antenas de barrido en 2D a varias frecuencias en el rango de milimétricas y sub-milimétricas, y se proponen ciertas estrategias de direccionamiento que permiten conseguir este objetivo, se desarrolla el prototipo con direccionamiento en una dimensión con el fin de reducir el número de controles y posibles errores de fabricación, y así también validar la herramienta de diseño. Para un tamaño medio de apertura (con un numero de filas y columnas entre 30 y 50 elementos, lo que significa un reflectarray con un número de elementos superior a 900), la configuración “single offset” proporciona rangos de escaneo elevados, y ganancias que pueden oscilar entre los 20 y 30 dBi. En concreto, el prototipo medido proporciona un haz de barrido en un rango angular de 55º, en el que el nivel de lóbulos secundarios (SLL) permanece mejor de -13 dB en un ancho de banda de un 8%. La ganancia máxima es de 19.4 dBi. Estas prestaciones superan de forma clara aquellas conseguidas por otros autores. El segundo prototipo se corresponde con una antena de doble reflector que usa el reflectarray de cristal líquido como sub-reflector para escanear el haz en un plano (elevación o azimut). El objetivo básico de esta geometría es obtener mayores ganancias que en el reflectarray “single offset” con una estructura más compacta, aunque a expensas de reducir el rango de barrido. En concreto, se obtiene una ganancia máxima de 35 dBi, y un rango de barrido de 12º. Los procedimientos de síntesis de tensiones y de diseño de las estructuras de las celdas forman, en su conjunto, una herramienta completa de diseño precisa y eficiente de antenas reflectarray reconfigurables basados en cristales líquidos. Dicha herramienta se ha validado mediante el diseño, la fabricación y la medida de los prototipos anteriormente citados a 100 GHz, que consiguen algo nunca alcanzado anteriormente en la investigación de este tipo de antenas: unas prestaciones competitivas y una predicción excelente de los resultados. El procedimiento es general, y por tanto se puede usar a cualquier frecuencia en la que el cristal líquido ofrezca anisotropía dieléctrica, incluidos los THz. Los prototipos desarrollados en esta tesis doctoral suponen también unas de las primeras antenas de barrido real a frecuencias superiores a 100 GHz. En concreto, la antena de doble reflector para escaneo de haz es la primera antena reconfigurable electrónicamente a frecuencias superiores a 60 GHz que superan los 25 dBi de ganancia, siendo a su vez la primera antena de doble reflector que contiene un reflectarray reconfigurable como sub-reflector. Finalmente, se proponen ciertas mejoras que aún deben se deben realizar para hacer que estas antenas puedan ser un producto completamente desarrollado y competitivo en el mercado. ABSTRACT The work presented in this thesis is focused on the development of electronically reconfigurable antennas that are able to provide competitive electrical performance to the increasingly common applications operating at frequencies above 60 GHz. Specifically, this thesis presents the study, design, and implementation of reflectarray antennas, which incorporate liquid crystal (LC) materials to scan or reconfigure the beam electronically. From a general point of view, a liquid crystal can be defined as a material whose dielectric permittivity is variable and can be controlled with an external excitation, which usually corresponds with a quasi-static electric field (AC). By changing the dielectric permittivity at each cell that makes up the reflectarray, the phase shift on the aperture is controlled, so that a prescribed radiation pattern can be configured. Liquid Crystal-based reflectarrays have been chosen for several reasons. The first has to do with the advantages provided by the reflectarray antenna with respect to other high gain antennas, such as reflectors or phased arrays. The RF feeding in reflectarrays is achieved by using a common primary source (as in reflectors). This arrangement and the large number of degrees of freedom provided by the cells that make up the reflectarray (as in arrays), allow these antennas to provide a similar or even better electrical performance than other low profile antennas (reflectors and arrays), but assuming a more reduced cost and compactness. The second reason is the flexibility of the liquid crystal to be confined in an arbitrary geometry due to its fluidity (property of liquids). Therefore, the liquid crystal is able to adapt to a planar geometry so that it is one or more of the typical layers of this configuration. This simplifies drastically both the structure and manufacture of this type of antenna, even when compared with reconfigurable reflectarrays based on other technologies, such as diodes MEMS, etc. Therefore, the cost of developing this type of antenna is very small, which means that electrically large reconfigurable reflectarrays could be manufactured assuming low cost and greater productions. A paradigmatic example of a similar structure is the liquid crystal panel, which has already been commercialized successfully. The third reason lies in the fact that, at present, the liquid crystal is one of the few technologies capable of providing switching capabilities at frequencies above 60 GHz. In fact, the liquid crystal allows its permittivity to be switched in a wide range of frequencies, which are from DC to the visible spectrum, including microwaves and THz. Other technologies, such as ferroelectric materials, graphene or CMOS "on chip" technology also allow the beam to be switched at these frequencies. However, CMOS technology is expensive and is currently limited to frequencies below 150 GHz, and although ferroelectric materials or graphene can switch at higher frequencies and in a wider range, they have serious difficulties that make them immature. Ferroelectric materials involve the use of very high voltages to switch the material, making them unattractive, whereas the electromagnetic modelling of the graphene is still under discussion, so that the experimental results of devices based on this latter technology have not been reported yet. These three reasons make LC-based reflectarrays attractive for many applications that involve the use of electronically reconfigurable beams at frequencies beyond 60 GHz. Applications such as high resolution imaging radars, molecular spectroscopy, radiometers for atmospheric observation, or high frequency wireless communications (WiGig) are just some of them. This thesis is divided into three parts. In the first part, the most common properties of the liquid crystal materials are described, especially those exhibited in the nematic phase. The study is focused on the dielectric anisotropy (Ac) of uniaxial liquid crystals, which is defined as the difference between the parallel (e/7) and perpendicular (e±) permittivities: Ae = e,, - e±. This parameter allows the permittivity of a LC confined in an arbitrary volume at a certain biasing voltage to be described by solving a variational problem that involves both the electrostatic and elastic energies. Thus, the frequency dependence of (Ae) is also described and characterised. Note that an appropriate LC modelling is quite important to ensure enough accuracy in the phase shift provided by each cell that makes up the reflectarray, and therefore to achieve a good electrical performance at the antenna level. The second part of the thesis is focused on the design of resonant reflectarray cells based on liquid crystal. The reason why resonant cells have been chosen lies in the fact that they are able to provide enough phase range using the values of the dielectric anisotropy of the liquid crystals, which are typically small. Thus, the aim of this part is to investigate several reflectarray cell architectures capable of providing good electrical performance at the antenna level, which significantly improve the electrical performance of the cells reported in the literature. Similarly, another of the objectives is to develop a general tool to design these cells. To fulfill these objectives, the electrical yields of different types of resonant reflectarray elements are investigated, beginning from the simplest, which is made up of a single resonator and limits the state of the art. To overcome the electrical limitations of the single resonant cell, several elements consisting of multiple resonators are considered, which can be single-layer or multilayer. In a first step, the design procedure of these structures makes use of a conventional electromagnetic model which has been used in the literature, which considers that the liquid crystal behaves as homogeneous and isotropic materials whose permittivity varies between (e/7) y (e±). However, in this part of the thesis it is shown that the conventional modelling is not enough to describe the physical behaviour of the liquid crystal in reflectarray cells accurately. Therefore, a more accurate analysis and design procedure based on a more general model is proposed and developed, which defines the liquid crystal as an anisotropic three-dimensional inhomogeneous material. The design procedure is able to optimize multi-resonant cells efficiently to achieve good electrical performance in terms of bandwidth, phase range, losses, or sensitivity to the angle of incidence. The errors made when the conventional modelling (amplitude and phase) is considered have been also analysed for various cell geometries, by using measured results from several antenna prototypes made up of real liquid crystals at frequencies above 100 GHz. The measurements have been performed in a periodic environment using a quasi-optical bench, which has been designed especially for this purpose. One of these prototypes has been optimized to achieve a relatively large bandwidth (10%) at 100 GHz, low losses, a phase range of more than 360º, a low sensitivity to angle of incidence, and a low influence of the transversal inhomogeneity of the liquid crystal in the cell. The electrical yields of this prototype at the cell level improve those achieved by other elements reported in the literature, so that this prototype has been used in the last part of the thesis to perform several complete antennas for beam scanning applications. Finally, in this second part of the thesis, a novel strategy to characterise the macroscopic anisotropy using reflectarray cells is presented. The results in both RF and AC frequencies are compared with those obtained by other methods. The third part of the thesis consists on the study, design, manufacture and testing of LCbased reflectarray antennas in complex configurations. Note that the design procedure of a passive reflectarray antenna just consists on finding out the dimensions of the metallisations of each cell (which are used for phase control), using well-known optimization processes. However, in the case of reconfigurable reflectarrays based on liquid crystals, an additional step must be taken into account, which consists of accurately calculating the control voltages to be applied to each cell to configure the required phase-shift distribution on the surface of the antenna. Similarly, the structure to address the voltages at each cell and the control circuitry must be also considered. Therefore, the voltage synthesis is even more important than the design of the cell geometries (dimensions), since the voltages are directly related to the phase-shift. Several voltage synthesis procedures have been proposed in the state of the art, which are based on the experimental characterization of the phase/voltage curve. However, this characterization can be only carried out at a single angle of incidence and at certain cell dimensions, so that the synthesized voltages are different from those needed, thus giving rise to phase errors of more than 70°. Thus, the electrical yields of the LCreflectarrays reported in the literature are limited in terms of bandwidth, scanning range or side lobes level. In this last part of the thesis, a new voltage synthesis procedure has been defined and developed, which allows the required voltage to be calculated at each cell using simulations that take into account the particular dimensions of the cells, their angles of incidence, the frequency, and the AC biasing signal (frequency and waveform). The strategy is based on the modelling of each one of the permittivity states of the liquid crystal as an anisotropic substrate with longitudinal inhomogeneity (1D), or in certain cases, as an equivalent homogeneous tensor. The accuracy of both electromagnetic models is also discussed. The phase errors made by using the proposed voltage synthesis are better than 7º. In order to obtain an efficient tool to analyse and design the reflectarray, an electromagnetic analysis tool based on the Method of Moments in the spectral domain (SD-MoM) has also written and developed for anisotropic stratified media, which is used at each iteration of the voltage synthesis procedure. The voltage synthesis is also designed to minimize the effect of amplitude ripple on the radiation pattern, which is typical of reflectarrays made up of cells exhibiting high losses and represents a further advance in achieving a better antenna performance. To calculate the radiation patterns used in the synthesis procedure, an element-by-element analysis is assumed, which considers the local periodicity approach. Under this consideration, the use of a novel method is proposed, which avoids the limitation that the local periodicity imposes on the excitation. Once the appropriate strategy to calculate the voltages to be applied at each cell is developed, and once it is designed and manufactured both the structure to address the voltages to the antenna and the control circuits, two complete LC-based reflectarray antennas that operate at 100 GHz have been designed, manufactured and tested using the previously presented cells. The first prototype consists of a single offset reflectarray with beam scanning capabilities on one plane (elevation and azimuth). Although several LC-reflectarray antennas that provide 2-D scanning capabilities are also designed, and certain strategies to achieve the 2-D addressing of the voltage are proposed, the manufactured prototype addresses the voltages in one dimension in order to reduce the number of controls and manufacturing errors, and thereby validating the design tool. For an average aperture size (with a number of rows and columns of between 30 and 50 elements, which means a reflectarray with more than 900 cells), the single offset configuration provides an antenna gain of between 20 and 30 dBi and a large scanning range. The prototype tested at 100 GHz exhibits an electronically scanned beam in an angular range of 55º and 8% of bandwidth, in which the side lobe level (SLL) remains better than -13 dB. The maximum gain is 19.4 dBi. The electrical performance of the antenna is clearly an improvement on those achieved by other authors in the state of the art. The second prototype corresponds to a dual reflector antenna with a liquid crystal-based reflectarray used as a sub-reflector for beam scanning in one plane (azimuth or elevation). The main objective is to obtain a higher gain than that provided by the single offset configuration, but using a more compact architecture. In this case, a maximum gain of 35 dBi is achieved, although at the expense of reducing the scanning range to 12°, which is inherent in this type of structure. As a general statement, the voltage synthesis and the design procedure of the cells, jointly make up a complete, accurate and efficient design tool of reconfigurable reflectarray antennas based on liquid crystals. The tool has been validated by testing the previously mentioned prototypes at 100 GHz, which achieve something never reached before for this type of antenna: a competitive electrical performance, and an excellent prediction of the results. The design procedure is general and therefore can be used at any frequency for which the liquid crystal exhibits dielectric anisotropy. The two prototypes designed, manufactured and tested in this thesis are also some of the first antennas that currently operate at frequencies above 100 GHz. In fact, the dual reflector antenna is the first electronically scanned dual reflector antenna at frequencies above 60 GHz (the operation frequency is 100 GHz) with a gain greater than 25 dBi, being in turn the first dual-reflector antenna with a real reconfigurable sub-reflectarray. Finally, some improvements that should be still investigated to make these antennas commercially competitive are proposed.

Optical and ultraviolet observations of a strong flare in the young, single K2 dwarf LQ Hya

We present high-resolution optical echelle spectra and IUE observations during a strong flare on 1993 December 22 in the very active, young, rapidly rotating, single K2 dwarf LQ Hya. The initial impulsive phase of the flare, which started sometime between 2:42 ut and 4:07 ut, was characterized by strong optical continuum enhancement and blueshifted emission lines with broad wings. The optical chromospheric lines reached their maximum intensity at ≈ 5:31 ut, by which time the blueshift vanished and the optical continuum enhancement had sharply decreased. Thereafter, the line emission slowly decreased and the lines redshift in a gradual phase that lasted at least two more hours. The Mg II lines behaved similarly. Quiescent C IV flux levels were not recovered until 21 h later, though a data gap and a possible second flare make the interpretation uncertain. In addition to the typically flare-enhanced emission lines (e.g., H α and H β), we observe He I D_3 going into emission, plus excess emission (after subtraction of the quiescent spectrum) in other He I and several strong neutral metal lines (e.g., Mg I b). Flare enhancement of the far-ultraviolet continuum generally agrees with an Si I recombination model. We estimate the total flare energy, and discuss the broad components, asymmetries and Doppler shifts seen in some of the emission lines.

Image processing for safety assessment in Civil Engineering

Behaviour analysis of construction safety systems is of fundamental importance to avoid accidental injuries. Traditionally, measurements of dynamic actions in Civil Engineering have been done through accelerometers, but high-speed cameras and image processing techniques can play an important role in this area. Here, we propose using morphological image filtering and Hough transform on high-speed video sequence as tools for dynamic measurements on that field. The presented method is applied to obtain the trajectory and acceleration of a cylindrical ballast falling from a building and trapped by a thread net. Results show that safety recommendations given in construction codes can be potentially dangerous for workers.

A high-resolution binocular video-oculography system: assessment of pupillary light reflex and detection of an early incomplete blink and an upward eye movement

Background: The pupillary light reflex characterizes the direct and consensual response of the eye to the perceived brightness of a stimulus. It has been used as indicator of both neurological and optic nerve pathologies. As with other eye reflexes, this reflex constitutes an almost instantaneous movement and is linked to activation of the same midbrain area. The latency of the pupillary light reflex is around 200 ms, although the literature also indicates that the fastest eye reflexes last 20 ms. Therefore, a system with sufficiently high spatial and temporal resolutions is required for accurate assessment. In this study, we analyzed the pupillary light reflex to determine whether any small discrepancy exists between the direct and consensual responses, and to ascertain whether any other eye reflex occurs before the pupillary light reflex. Methods: We constructed a binocular video-oculography system two high-speed cameras that simultaneously focused on both eyes. This was then employed to assess the direct and consensual responses of each eye using our own algorithm based on Circular Hough Transform to detect and track the pupil. Time parameters describing the pupillary light reflex were obtained from the radius time-variation. Eight healthy subjects (4 women, 4 men, aged 24–45) participated in this experiment. Results: Our system, which has a resolution of 15 microns and 4 ms, obtained time parameters describing the pupillary light reflex that were similar to those reported in previous studies, with no significant differences between direct and consensual reflexes. Moreover, it revealed an incomplete reflex blink and an upward eye movement at around 100 ms that may correspond to Bell’s phenomenon. Conclusions: Direct and consensual pupillary responses do not any significant temporal differences. The system and method described here could prove useful for further assessment of pupillary and blink reflexes. The resolution obtained revealed the existence reported here of an early incomplete blink and an upward eye movement.

Method for targetless tracking subpixel in-plane movements

We present a targetless motion tracking method for detecting planar movements with subpixel accuracy. This method is based on the computation and tracking of the intersection of two nonparallel straight-line segments in the image of a moving object in a scene. The method is simple and easy to implement because no complex structures have to be detected. It has been tested and validated using a lab experiment consisting of a vibrating object that was recorded with a high-speed camera working at 1000 fps. We managed to track displacements with an accuracy of hundredths of pixel or even of thousandths of pixel in the case of tracking harmonic vibrations. The method is widely applicable because it can be used for distance measuring amplitude and frequency of vibrations with a vision system.

Ultrathin high-index metasurfaces for shaping focused beams

The volume size of a converging wave, which plays a relevant role in image resolution, is governed by the wavelength of the radiation and the numerical aperture (NA) of the wavefront. We designed an ultrathin (λ/8 width) curved metasurface that is able to transform a focused field into a high-NA optical architecture, thus boosting the transverse and (mainly) on-axis resolution. The elements of the metasurface are metal-insulator subwavelength gratings exhibiting extreme anisotropy with ultrahigh index of refraction for TM polarization. Our results can be applied to nanolithography and optical microscopy.

Manufacture of high pressure die-cast radio frequency filter bodies

The manufacture of a radio frequency filter box using high pressure die casting (HPDC) is compared to the traditional high speed machining route. This paper describes an industrial exercise that concluded HPDC to be an economical and appropriate method to produce larger volumes of thin-walled telecommunications components. Modifications to the component design were made to make the component suitable for the HPDC process. Development of the die design through simulation modelling is described. The wrought alloy was replaced by near-eutectic Al-Si die casting alloy that was found to give better temperature stability performance. Apart from the economic benefits, HPDC was found to give lower filter efficiency losses through better surface finish. The effects of HPDC process variables, such as intensification pressure and injection piston velocity, on component quality, particularly porosity levels, were investigated. The pressure was analysed in terms of HPDC machine set pressure and the pressure measured in the die cavity by pressure sensors. Porosity was found to decrease with increased pressure and slightly increase with higher casting velocities.

Distance measurement using the change in junction voltage across a laser diode due to the self-mixing effect

Conventional detection scheme for self-mixing sensors uses an integrated photodiode within the laser package to monitor the self mixing signal. This arrangement can be simplified by directly obtaining the self-mixing signals across the laser diode itself and omitting the photodiode. This work reports on a Vertical-Cavity Surface-Emitting Laser (VCSEL) based selfmixing sensor using the laser junction voltage to obtain the selfmixing signal. We show that the same information can be obtained with only minor changes to the extraction circuitry leading to potential cost saving with reductions in component costs and complexity and significant increase in bandwidth favoring high speed modulation. Experiments using both photo current and voltage detection were carried out and the results obtained show good agreement with the theory.

Test strategies on functionally partitioned module-based programmable architecture for base-band processing

A specialised reconfigurable architecture for telecommunication base-band processing is augmented with testing resources. The routing network is linked via virtual wire hardware modules to reduce the area occupied by connecting buses. The number of switches within the routing matrices is also minimised, which increases throughput without sacrificing flexibility. The testing algorithm was developed to systematically search for faults in the processing modules and the flexible high-speed routing network within the architecture. The testing algorithm starts by scanning the externally addressable memory space and testing the master controller. The controller then tests every switch in the route-through switch matrix by making loops from the shared memory to each of the switches. The local switch matrix is also tested in the same way. Next the local memory is scanned. Finally, pre-defined test vectors are loaded into local memory to check the processing modules. This algorithm scans all possible paths within the interconnection network exhaustively and reports all faults. Strategies can be inserted to bypass minor faults

Character recognition systems using Fourier transformation in incoherent light

Many attempts have been made to overcome problems involved in character recognition which have resulted in the manufacture of character reading machines. An investigation into a new approach to character recognition is described. Features for recognition are Fourier coefficients. These are generated optically by convolving characters with periodic gratings. The development of hardware to enable automatic measurement of contrast and position of periodic shadows produced by the convolution is described. Fourier coefficients of character sets were measured, many of which are tabulated. Their analysis revealed that a few low frequency sampling points could be selected to recognise sets of numerals. Limited treatment is given to show the effect of type face variations on the values of coefficients which culminated in the location of six sampling frequencies used as features to recognise numerals in two type fonts. Finally, the construction of two character recognition machines is compared and contrasted. The first is a pilot plant based on a test bed optical Fourier analyser, while the second is a more streamlined machine d(3signed for high speed reading. Reasons to indicate that the latter machine would be the most suitable to adapt for industrial and commercial applications are discussed.