Operational Cost Reduction in WDM Networks using Lighttours

Wavelength division multiplexing (WDM) networks have been adopted as a near-future solution for the broadband Internet. In previous work we proposed a new architecture, named enhanced grooming (G+), that extends the capabilities of traditional optical routes (lightpaths). In this paper, we compare the operational expenditures incurred by routing a set of demands using lightpaths with that of lighttours. The comparison is done by solving an integer linear programming (ILP) problem based on a path formulation. Results show that, under the assumption of single-hop routing, almost 15% of the operational cost can be reduced with our architecture. In multi-hop routing the operation cost is reduced in 7.1% and at the same time the ratio of operational cost to number of optical-electro-optical conversions is reduced for our architecture. This means that ISPs could provide the same satisfaction in terms of delay to the end-user with a lower investment in the network architecture

Effects of the epitaxial layer thickness on the noise properties of Schottky barrier diodes

An analytical theory to describe the combined effects of the epitaxial layer thickness and the ohmic contact on the noise properties of Schottky barrier diodes is presented. The theory, which provides information on both the local and the global noise properties, takes into account the finite size of the epitaxial layer and the effects of the back ohmic contact, and applies to the whole range of applied bias. It is shown that by scaling down the epitaxial layer thickness, the current regime in which the noise temperature displays a shot-noise-like behavior increases at the cost of reducing the current range in which the thermal-noise-like behavior dominates. This improvement in noise temperature is limited by the effects of the ohmic contact, which appear for large currents. The theory is formulated on general trends, allowing its application to the noise analysis of other semiconductor devices operating under strongly inhomogeneous distributions of the electric field and charge concentrations.

Effects of the epitaxial layer thickness on the noise properties of Schottky barrier diodes

An analytical theory to describe the combined effects of the epitaxial layer thickness and the ohmic contact on the noise properties of Schottky barrier diodes is presented. The theory, which provides information on both the local and the global noise properties, takes into account the finite size of the epitaxial layer and the effects of the back ohmic contact, and applies to the whole range of applied bias. It is shown that by scaling down the epitaxial layer thickness, the current regime in which the noise temperature displays a shot-noise-like behavior increases at the cost of reducing the current range in which the thermal-noise-like behavior dominates. This improvement in noise temperature is limited by the effects of the ohmic contact, which appear for large currents. The theory is formulated on general trends, allowing its application to the noise analysis of other semiconductor devices operating under strongly inhomogeneous distributions of the electric field and charge concentrations.

An analytic approach to distribution logistics strategic management

Logistics management is increasingly being recognised by many companies to be of critical concern. The logistics function includes directly or indirectly many of the new areas for achieving or maintaining competitive advantage that companies have been forced to develop due to increasing competitive pressures. The key to achieving a competitive advantage is to manage the logistics function strategically which involves determining the most cost effective method of providing the necessary customer service levels from the many combinations of operating procedures in the areas of transportation, warehousing, order processing and information systems, production, and inventory management. In this thesis, a comprehensive distribution logistics strategic management process is formed by integrating the periodic strategic planning process with a continuous strategic issues management process. Strategic planning is used for defining the basic objectives for a company and assuring co operation and synergy between the different functions of a company while strategic issues management is used on a continuous basis in order to deal with environmental and internal turbulence. The strategic planning subprocess consists of the following main phases: (1) situational analyses, (2) defining the vision and strategic goals for the logistics function, (3) determining objectives and strategies, (4) drawing up tactical action plans, and (5) evaluating the implementation of the plans and making the needed adjustments. The aim of the strategic issues management subprocess is to continuously scan the environment and the organisation for early identification of the issues having a significant impact on the logistics function using the following steps: (1) the identification of trends, (2) assessing the impact and urgency of the identified trends, (3) assigning priorities to the issues, and (4) planning responses to the, issues. The Analytic Hierarchy Process (AHP) is a systematic procedure for structuring any problem. AHP is based on the following three principles: decomposition, comparative judgements, and synthesis of priorities. AHP starts by decomposing a complex, multicriteria problem into a hierarchy where each level consists of a few manageable elements which are then decomposed into another set of elements. The second step is to use a measurement methodology to establish priorities among the elements within each level of the hierarchy. The third step in using AHP is to synthesise the priorities of the elements to establish the overall priorities for the decision alternatives. In this thesis, decision support systems are developed for different areas of distribution logistics strategic management by applying the Analytic Hierarchy Process. The areas covered are: (1) logistics strategic issues management, (2) planning of logistic structure, (3) warehouse site selection, (4) inventory forecasting, (5) defining logistic action and development plans, (6) choosing a distribution logistics strategy, (7) analysing and selecting transport service providers, (8) defining the logistic vision and strategic goals, (9) benchmarking logistic performance, and (10) logistic service management. The thesis demonstrates the potential of AHP as a systematic and analytic approach to distribution logistics strategic management.

Cost estimation framework for modular product

Cost estimation is an important, but challenging process when designing a new product or a feature of it, verifying the product prices given by suppliers or planning a cost saving actions of existing products. It is even more challenging when the product is highly modular, not a bulk product. In general, cost estimation techniques can be divided into two main groups - qualitative and quantitative techniques - which can further be classified into more detailed methods. Generally, qualitative techniques are preferable when comparing alternatives and quantitative techniques when cost relationships can be found. The main objective of this thesis was to develop a method on how to estimate costs of internally manufactured and commercial elevator landing doors. Because of the challenging product structure, the proposed cost estimation framework is developed under three different levels based on past cost information available. The framework consists of features from both qualitative and quantitative cost estimation techniques. The starting point for the whole cost estimation process is an unambiguous, hierarchical product structure so that the product can be classified into controllable parts and is then easier to handle. Those controllable parts can then be compared to existing past cost knowledge of similar parts and create as accurate cost estimates as possible by that way.

Analyzing the cost-efficiency and performance of a payroll department by benchmarking

Tämän diplomityön tavoitteena oli analysoida Stora Enson palkkakeskuksen ja sen henkilöstöhallinnon järjestelmän, SAP HR:n, kustannustehokkuutta ja suorituskykyä. Tutkimuksessa käytettiin apuna benchmarkingia. Viisi suurta suomalaisyritystä osallistui benchmarkingiin. Benchmarkingin pääkohteena oli yritysten välinen kustannusvertailu. Kyselyssä perehdyttiin myös yritysten järjestelmien suorituskykyyn. Tuloksien perusteella Stora Enson palkkakeskus tarjoaa kustannustehokkaan ja kilpailukykyisen ratkaisun, joka menestyy hyvin vertailussa muihin suomalaisiin yrityksiin.

Balancing effluent quality, economic cost and greenhouse gas emissions during the evaluation of (plant-wide) control/operational strategies in WWTPs

The objective of this paper was to show the potential additional insight that result from adding greenhouse gas (GHG) emissions to plant performance evaluation criteria, such as effluent quality (EQI) and operational cost (OCI) indices, when evaluating (plant-wide) control/operational strategies in wastewater treatment plants (WWTPs). The proposed GHG evaluation is based on a set of comprehensive dynamic models that estimate the most significant potential on-site and off-site sources of CO2, CH4 and N2O. The study calculates and discusses the changes in EQI, OCI and the emission of GHGs as a consequence of varying the following four process variables: (i) the set point of aeration control in the activated sludge section; (ii) the removal efficiency of total suspended solids (TSS) in the primary clarifier; (iii) the temperature in the anaerobic digester; and (iv) the control of the flow of anaerobic digester supernatants coming from sludge treatment. Based upon the assumptions built into the model structures, simulation results highlight the potential undesirable effects of increased GHG production when carrying out local energy optimization of the aeration system in the activated sludge section and energy recovery from the AD. Although off-site CO2 emissions may decrease, the effect is counterbalanced by increased N2O emissions, especially since N2O has a 300-fold stronger greenhouse effect than CO2. The reported results emphasize the importance and usefulness of using multiple evaluation criteria to compare and evaluate (plant-wide) control strategies in a WWTP for more informed operational decision making

A low-cost ultrasonic spray dryer to produce spherical microparticles from polymeric matrices

The spray-drying technique has been widely used for drying heat-sensitive foods, pharmaceuticals, and other substances, because it leads to rapid solvent evaporation from droplets. This method involves the transformation of a feed from a fluid state into a dried particulate, by spraying the feed into a hot medium. Despite being most often considered a dehydration process, spray drying can also be used as an encapsulation method. Therefore, this work proposes the use of a simple and low-cost ultrasonic spray dryer system to produce spherical microparticles. This equipment was successfully applied to the preparation of dextrin microspheres on a laboratory scale and for academic purposes.

Estudi de software lliure en diferents entorns

El software lliure està tenint últimament un pes cada cop més important en les empreses, però encara és el gran desconegut per a molta gent. Des de la seva creació als anys 80 fins ara, hi ha hagut un creixement exponencial de software lliure de gran qualitat, oferint eines per a tot tipus de necessitats, eines ofimàtiques, gestors de correu, sistemes de fitxer, sistemes operatius…. Tot aquest moviment no ha passat desapercebut per a molts usuaris i empreses, que s’han aprofitat d’ell per cobrir les seves necessitats. Pel que fa a les empreses, cada cop n’hi ha més que en petita o gran mesura, utilitzen el software lliure, ja sigui per el seu menor cost d’adquisició, o bé per la seva gran fiabilitat o per que és fàcilment adaptable o per no establir cap lligam tecnològic, en definitiva per tenir més llibertat. En el moment de la creació d’una nova empresa, on es parteix de zero en tota la tecnologia informàtica, és el moment menys costòs d’implementar l’arquitectura informàtica amb software lliure, és quan l’impacte que té sobre l’empresa, usuaris i clients és menor. En les empreses que ja tenen un sistema informàtic, caldrà establir un pla de migració, ja sigui total o parcial. La finalitat d’aquest projecte no és la de dir quin software és millor que l’altre o de dir quin s’ha d’instal•lar, sinó el de donar a conèixer el món del software lliure, mostrar part d’aquest software, fer alguna comparativa de software lliure amb software propietari, donant idees i un conjunt de solucions per a empreses, per què una empresa pugui agafar idees d’implementació d’algunes de les solucions informàtiques exposades o seguir algun dels consells proposats. Actualment ja hi ha moltes empreses que utilitzen software lliure. Algunes només n’utilitzen una petita part en les seves instal•lacions, ja que el fet de que una empresa funcioni al 100% amb software lliure, tot i que n’hi comença ha haver, de moment ho considero una mica arriscat, però que en poc temps, aquest fet serà cada cop més habitual.

Sellutehtaan sekundäärilämmön käytön tehostaminen

Energia on olennainen osa nykyaikaisen sellutehtaan prosesseja, joissa kuluu suuria määriä lämpöä ja sähköä. Pyrittäessä entistä kustannustehokkaampaan liiketoimintaan nousee energiatehokkuus usein mielenkiinnon kohteeksi. Pitkälle viety sähkön ja lämmön yhteistuotanto yhdistettynä korkeaan biopolttoaineiden osuuteen energian tuotannossa luovat pohjan tälle pyrkimykselle. Sekundäärilämpöä syntyy prosessien sivutuotteena ja sen mahdollisimman suuri hyödyntäminen on yksi keino päästä kohti parempaa energiatehokkuutta. Joissain tapauksissa sillä voidaan korvata jopa primäärienergian käyttöä ja mahdollisesti pienentää ostopolttoaineiden tarvetta. Diplomityössä tutkitaan sellutehtaan sekundäärilämpöjärjestelmän toimintaa, ohjausta ja energiankulutusta. Sekundäärilämpöjärjestelmästä muodostetaan taseet talvitilanteessa ja samalla etsitään mahdollisia uusia talteenotettavia sekundäärilämpövirtoja tai vastaavasti käyttökohteita. Lisäksi päivitetään sekundäärilämpöjärjestelmän raportoinnin ja ohjauksen työkaluja nykytilannetta vastaavaksi. Työn aikana kiinnitetään myös huomiota järjestelmän toimintaan muutostilanteissa, joissa kaikkia vesijakeita ei välttämättä ole saatavilla prosessin tarvitsemia määriä.

Strategic Development of Electricity Distribution Networks – Concept and Methods

Strategic development of distribution networks plays a key role in the asset management in electricity distribution companies. Owing to the capital-intensive nature of the field and longspan operations of companies, the significance of a strategy is emphasised. A well-devised strategy combines awareness of challenges posed by the operating environment and the future targets of the distribution company. Economic regulation, ageing infrastructure, scarcity of resources and tightening supply requirements with challenges created by the climate change put a pressure on the strategy work. On the other hand, technology development related to network automation and underground cabling assists in answering these challenges. This dissertation aims at developing process knowledge and establishing a methodological framework by which key issues related to network development can be addressed. Moreover, the work develops tools by which the effects of changes in the operating environment on the distribution business can be analysed in the strategy work. To this end, the work discusses certain characteristics of the distribution business and describes the strategy process at a principle level. Further, the work defines the subtasks in the strategy process and presents the key elements in the strategy work and long-term network planning. The work delineates the factors having either a direct or indirect effect on strategic planning and development needs in the networks; in particular, outage costs constitute an important part of the economic regulation of the distribution business, reliability being thus a key driver in network planning. The dissertation describes the methodology and tools applied to cost and reliability analyses in the strategy work. The work focuses on determination of the techno-economic feasibility of different network development technologies; these feasibility surveys are linked to the economic regulation model of the distribution business, in particular from the viewpoint of reliability of electricity supply and allowed return. The work introduces the asset management system developed for research purposes and to support the strategy work, the calculation elements of the system and initial data used in the network analysis. The key elements of this asset management system are utilised in the dissertation. Finally, the study addresses the stages of strategic decision-making and compilation of investment strategies. Further, the work illustrates implementation of strategic planning in an actual distribution company environment.

Kinetic modeling of the biosorption of Cd2+ ions from aqueous solutions onto Eichhornia crassipes roots using potentiometry: low-cost alternative to conventional methods

This work presents the use of potentiometric measurements for kinetic studies of biosorption of Cd2+ ions from aqueous solutions on Eichhornia crassipes roots. The open circuit potential of the Cd/Cd2+ electrode of the first kind was measured during the bioadsorption process. The amount of Cd2+ ions accumulated was determined in real time. The data were fit to different models, with the pseudo-second-order model proving to be the best in describing the data. The advantages and limitations of the methodology proposed relative to the traditional method are discussed.