Mach-Zehnder interferometers with asymmetric modulation arms in applications of high speed silicon-on-insulator based optical switches

Modulation arms with different widths are introduced to Mach-Zehnder interferometers (MZIs) to obtain improved performance. Theoretical analysis and numerical simulation have shown that when the widths of the two arms are properly designed to achieve an inherent m pi/2 (m is an odd integer) optical phase difference between the arms, the asymmetric MZI presents higher modulation speed. Furthermore, the carrier-absorption induced divergence of insertion losses in silicon-on-insulator (SOI) based MZI optical switches can be obviously improved.

Structural and optical properties of strain-compensated GaAsSb/GaAs quantum wells with high Sb composition

The structural and optical properties of GaAsSb/GaAs quantum wells (QWs) and strain-compensated GaAsP/GaAs/GaAsSb/GaAs/GaAsP QWs grown on a GaAs substrate by molecular beam epitaxy are investigated using high-resolution x-ray diffraction and photoluminescence (PL) measurements. We demonstrated that the insertion of tensile GaAsP layers into the active region of GaAsSb/GaAs QWs effectively improves the structural and optical quality. Even the Sb composition is as high as 0.39. The PL spectra at 11 K and room temperature indicate that the PL peak of strain-compensated QWs has a narrower linewidth and higher intensity in comparison to the sample without strain compensation. The results of PL peak blueshift with increasing excitation show the strain-compensated GaAsSb/GaAs interface characteristic of type-I band alignment. (C) 2003 American Institute of Physics.

Correlation of calibration equations for test fixtures

This paper begins from the thru-short-open (TSO) and thru-line-match (TLM) methods to investigate the correlation of the calibration equations of these two methods, The relations among the measurements with the corresponding standards are obtained. It is found that the line standard with zero length can be used instead of ideal open and short, in case that two test fixtures are symmetrical. For asymmetrical fixtures, the measurements with the standards line, open and short are related at certain frequencies, and the matched load can be replaced by the line standards. The relations established are used to test short and match standards and analyze the freqPuency limits of the TSO method, Good agreement between theory and experiment is obtained, It is found that the TSO method becomes very poor when the insertion phase of the thru standard is near n pi/4, and this method has a lower frequency limit. The TLM method is found unsuitable for calibrating asymmetrical fixtures.

AlGaN layers grown on AlGaN buffer layer and GaN buffer layer using strain-relief interlayers - art. no. 68410S

We investigated AlGaN layers grown by metalorganic chemical vapor deposition (MOCVD) on high temperature (HT-)GaN and AlGaN buffer layers. On GaN buffer layer, there are a lot of surface cracking because of tensile strain in subsequent AlGaN epilayers. On HT-AlGaN buffer layer, not only cracks but also high densities rounded pits present, which is related to the high density of coalescence boundaries in HT-AlGaN growth process.The insertion of interlayer (IL) between AlGaN and the GaN pseudosubstrate can not only avoid cracking by modifying the strain status of the epilayer structure, but also improved Al incorporation efficiency and lead to phase-separation. And we also found the growth temperature of IL is a critical parameter for crystalline quality of subsequent AlGaN epilayer. Low temperature (LT-) A1N IL lead to a inferior quality in subsequent AlGaN epilayers.

SOI optical switch matrix integrated with spot size converter (SSC) and total internal reflection (TIR) mirrors

SOI (Silicon on Insulator) based photonic devices has attracted more and more attention in the recent years. Integration of SOI optical switch matrix with isolating grooves, total internal reflection (TIR) mirrors and spot size converter (SSC) was studied. A folding re-arrangeable non-blocking 4x4 optical switch matrix and a blocking 16x16 matrix with TIR mirrors and SSC were fabricated on SOI wafer. The performaces, including extinction ratio and the crosstalk, are better than before. The insertion loss and the polarization dependent loss (PDL) at 1.55 mu m increase slightly with longer device length, more bend and intersecting waveguides. The insertion losses decrease 2 similar to 3 dB when anti-reflection films are added in the ends of the devices. The rise and fall times of the devices are 2.1 mu s and 2.3 mu s, respectively.

SOI-based thermo-optic waveguide switch matrix with spot size converters

A SOI-based thermo-optic waveguide switch matrix worked at 1.55 mu m, integrated with spot size converters is designed and fabricated for the first time. The insertion loss and polarization dependent loss are less than 13dB and 2dB, respectively. The extinction ratio is larger than 19dB. The response time is less than 5 mu s and the power consumption of the switch cell is about 200mW.

Recent progresses of SOI-based photonic devices - art. no. 60201R

SOI (Silicon on Insulator) based photonic devices, including stimulated emission from Si diode, RCE (Resonant Cavity Enhanced) photodiode with quantum structure, MOS (Metal Oxide Semiconductor) optical modulator with high frequency, SOI optical matrix switch and wavelength tunable filter are reviewed in the paper. The emphasis will be played on our recent results of SOI-based thermo-optic waveguide matrix switch with low insertion loss and fast response. A folding re-arrangeable non-blocking 4x4 matrix switch with total internal reflection (TIR) mirrors and a first blocking 16 x 16 matrix were fabricated on SOI wafer. The extinction ratio and the crosstalk are better. The insertion loss and the polarization dependent loss (PDL) at 1.55 mu m increase slightly with longer device length and more bend and intersecting waveguides. The insertion losses are expected to decrease 2-3 dB when anti-reflection films are added in the ends of the devices. The rise and fall times of the devices are 2.1 mu s and 2.3 mu s, respectively.

一种Web应用服务器集群管理系统的设计与实现

随着计算机的普及和网络技术的发展，Internet上的Web用户爆炸性增长。作为Web应用主要支撑平台的Web应用服务器经常面临过载的问题。Web应用服务器集群技术是解决这一问题的有效手段。然而，集群规模变大导致的集群拓扑结构复杂、计算环境的高度异构以及应用对性能等非功能需求的多样化使得Web应用服务器集群的安装、配置和维护等管理过程难度大大增加。Web应用服务器集群迫切需要改变目前静态、被动的管理方式，而通过自管理方式来降低其管理成本、适应计算环境变化以及应用的个性化非功能需求。 Web应用服务器集群管理主要包括拓扑结构、资源以及负载等方面的管理。本文设计了一个Web应用服务器集群管理系统。针对集群拓扑结构管理，设计了基于广播的集群节点自配置设施，并通过基于Cookie Insertion的请求会话粘滞设计实现了多个负载均衡器的协同工作；针对集群资源管理，设计了基于Java规则引擎的动态资源管理框架，并在此基础上实现了集群规模的动态调整；针对集群负载管理，设计了基于反馈-控制机制的动态负载均衡算法，可根据节点负载动态调整权值，使集群能够适应负载变化。 基于上述设计，本论文在Web应用服务器系统OnceAS中实现了该集群管理系统，包括支持多种通信模式的集群通信组件，拓扑结构管理器，资源管理器，负载均衡器，以及节点管理器，同时提供了相应的管理工具。系统测试结果表明，该系统支持集群拓扑结构、资源和负载的管理，能够更好地适应负载变化，提高Web应用服务器的整体性能表现。

GAAS/GAALAS GRADED INDEX SEPARATE CONFINEMENT SINGLE QUANTUM-WELL SINGLE-MODE WAVE-GUIDE ELECTROABSORPTION LIGHT-MODULATOR

A GaAs/GaAlAs graded-index separate confinement single quantum well heterostructure single-mode ridge waveguide electroabsorption modulator was fabricated and investigated. For the modulator with a quantum well width of 100 angstrom and device length of 700-mu-m, an on/off ratio of 29.7 dB and estimated absorption insertion loss of 3 dB were obtained for TE polarised light with wavelength 8650 angstrom, and for TM polarisation the on/off ratio was 28.5 dB. With a switching voltage of 1 V, an on/off ratio of 15 dB was achieved. Photocurrent spectra exhibited a red shift of 600 angstrom of the absorption edge when the voltage applied to the PIN diode was varied from 0.5 to -7 V. The corresponding shift of the room temperature exciton peak energy was 96 meV.

Optimization of Global Signal Networks for Island-Style FPGAs

We present a staggered buffer connection method that provides flexibility for buffer insertion while designing global signal networks using the tile-based FPGA design methodology. An exhaustive algorithm is used to analyze the trade-off between area and speed of the global signal networks for this staggered buffer insertion scheme, and the criterion for determining the design parameters is presented. The comparative analytic result shows that the methods in this paper are proven to be more efficient for FPGAs with a large array size.

An Improvement on 2× 2 Silicon-on-Insulator Mach-Zehnder Thermo-Optical Switch

An improved 2 ×2 silicon-on-insulator Mach-Zehnder thermo-optical switch is designed and fabricated, which is based on strongly guided multimode interference couplers and single- mode phase-shifting arms. The multimode interference couplers and input/output waveguides are deeply etched to improve coupler performances and coupler-waveguide coupling efficiencies. However, shallow etching is used in the phase-shifting arms to guarantee single-mode property. The strongly guided coupler presents an attractive uniformity about 0. 03 dB and a low propagation loss of -0.6 dB. The 2× 2 switch shows an insertion loss as low as -6.8 dB, where the fiber-waveguide coupling loss of -4.3 dB is included, and the response-time is measured as short as 6.8 μs, which are much better than our previous results.

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (＜-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.

Scan test in 18x8 bits Booth Coding-Wallace Tree multiplier

Scan test can be inserted around hard IP cores that have not been designed with DFT approaches. An 18x18 bits Booth Coding-Wallace Tree multiplier has been designed with full custom approach with 0.61 m CMOS technology. When we reuse the multiplier in another chip, scan chain has been inserted around it to increase the fault coverage. After scan insertion, the multiplier needs 4.7% more areas and 24.4% more delay time, while the fault coverage reaches to 95%.

粗枝云杉( Picea asperata Mast.)天然群体的遗传变异

西南地区在我国的经济发展和生态环境建设中占重要地位，但也是我国生态环境最脆弱的地区之一，生态系统退化，生态功能减弱，严重制约着西南林业的可持续经营与发展。本项目采用DNA 分子标记SSR 研究不同生境条件下粗枝云杉群体的遗传变异及其时空分布格局，考察遗传变异与复杂的山地生态环境间的潜在联系，系统地揭示粗枝云杉天然群体与环境系统相互作用的生态适应与分子进化机制。粗枝云杉适应性强，生长迅速，在植树造林和工业用材方面占有重要地位，研究成果可为中国西南部亚高山天然林的可持续经营及退化生态系统的恢复与重建提供理论依据和科学指导。主要研究结果如下： 1. SSR 位点变异丰富，等位基因频率的分布格局多样。7 个SSR 标记全是多态位点，每位点的等位基因数变化范围为13~24，平均为19.9 个。SSR 位点的等位基因片段长度范围变化较大。73.1%的等位基因变异遵循逐步突变模型(SSM)而发生1 个重复基元的变化，22.3%和4.6%的变异分别按两阶段突变模型(TMP)发生1 个重复基元以上的变化和在SSR 位点侧翼区发生1 个碱基变化的插入-删除事件。 2. 粗枝云杉拥有中等偏高水平的遗传多样性和相对大的群体间遗传分化。通过分析代表10 个群体的250 个个体在7 个SSR位点的变化，调查了源自中国西南山区的粗枝云杉的微卫星变异。相当高的遗传多样性和强烈的群体分化发生在粗枝云杉中， 其群体平均Nei's 期望杂合度为0.707 ， 群体间遗传距离为0.121~0.224(FST)和0.100~0.537(RST)。然而，群体间遗传距离与地理距离之间无相关性，从而排除了简单的距离分离模式并暗示迁移不是影响粗枝云杉遗传变异格局的主要因素。事实上，使用私有等位基因估算的基因流数量非常低，仅等于0.753。等位基因置换检验(Allele permutation tests)揭示逐步突变及遗传漂变都对群体间分化有贡献。另外，在多数位点检测到显著的群体间遗传差异，这个结果说明自然选择，假设通过环境压力，是引起粗枝云杉微地理分化的主要因素之一。根据SSR基因型，250 个粗枝云杉个体的70%被正确地归类入其各自的来源群体，结果表明微卫星(SSR)对区分来自中国不同生态地理位点的粗枝云杉基因型是有效的。 3. 在SSR、RAPD 和AFLP 位点，显著的群体间遗传结构被发现的，但三种标记间遗传分化程度和群体遗传关系有差异。利用来自10 个群体的247 个个体，我们报告了关于样本粗枝云杉群体间遗传关系的总体看法。根据各自对评价遗传关系的信息能力和适用性，SSR、RAPD 和AFLP 标记被选用，三种技术非常有效地区别这些基因型。使用的SSR、RAPD 和AFLP 标记分别估计平均Dice 相似性系数。Mantel 检验产生显著但相对低的共表型适合度(RAPD = 0.63£AFLP = 0.60和SSR = 0.75)。比较三种标记系统，RAPD 和AFLP 共表型指数相对高地相关(r =0.59)，而RAPD 和SSR 及SSR 和AFLP 之间的相关系数分别是0.53 和0.35。所有系统树，包括不同标记资料结合获得的系统树，反映了多数群体依据它们的地理条件而成某种特定关系。结果暗示单个或结合标记系统能用来深入洞察粗枝云杉遗传研究，并且不同标记系统合并资料能提供更可靠的信息。 Southwestern region plays an important role in economic developmentand ecological construction in China. Yet, it is also one of the weak regionsof ecological environment in China with degraded ecosystem and imperfectfunction, which restricts the sustaining management and development ofsouthwestern forestry. The genetic variation and spatial distribution patternof P. asperata populations originating from different habitats wereinvestigated using SSR molecular markers in this study. The correlationsbetween genetic variation and ecological and environmental conditionswere detected, and the interaction between P. asperata populations andenvironmental system and the mechanism of ecological adaption -molecular evolution were revealed. Given the significant ecological andeconomic roles of the fast-growing and wide-adaptive species in reforestation and production of pulp wood and timber, the study couldprovide a strong theoretical evidence and scientific direction for thesustaining management of subalpine natural forest, and the afforestationand rehabilitation of degraded ecosystem. The results are as follows: 1. The genetic variation at SSR loci was abundant and the distributionof allelic frequencies was uneven. All seven loci were polymorphic, and thenumber of alleles per locus varied from 13 to 24 with a mean valueequaling 19.9. The allele sizes at SSR loci were found to vary widely.73.1% of allelic variation followed stepwise mutation model (SSM) whichresults increase or decrease by one repeat type, and 22.3% and 4.6% wereresulted from two-phase mutation model (TMP) with allele size varying bymore than one repeat type and from insertion-deletion events in theflanking regions at SSR loci with a single basepair changing, respectively. 2. P. asperata possessed a moderate to high level of genetic diversityand considerable genetic differentiation. Microsatellite variation of P.asperata. originating from the mountains of southwestern China wasinvestigated by analyzing variation at seven SSR loci in 250 individualsrepresenting ten populations. A fair degree of genetic diversity and strongpopulation subdivision occurred with the mean gene diversity (H) of 0.707,and genetic distances among populations varying between 0.121 and 0.224(FST) and between 0.100 and 0.537 (RST). However, inter-populationgenetic distances showed no correlation with geographic distances between the population sites. This ruled out a simple isolation by distance modeland suggested that migration does not have a great impact. In fact, theamount of gene flow, detected using private alleles, was very low, equalingonly 0.753. Allele permutation tests revealed that stepwise-like mutations,coupled with genetic drift, could contribute to population differentiation.Moreover, significant genetic differences between populations weredetected at most loci. The results indicate that natural selection, presumablythrough environmental stress, may be one of the main factors causingmicro-geographical differentiation in the genetic structure of P. asperata.Based on SSR genotypes, 70% of the 250 individuals were correctlyclassified into their sites of origin. This suggests that microsatellites (SSRs) are effective in distinguishing genotypes of P. asperata originating fromdiverse eco-geographical sites in China. 3. Using a set of 247 individuals from ten P. asperata populations wereport an overview on the genetic relationship among the sampled P.asperata populations. RAPD, AFLP and SSR were used in terms of theirinformativeness and applicability for evaluate relationship and all threetechniques discriminated the genotypes very effectively. Mean Dicesimilarities coefficient were estimated using RAPD, AFLP and SSR,respectively. The Mantel test resulted in a significant but relatively low fit(RAPD = 0.63, AFLP = 0.60 and SSR = 0.75) of cophenetic values.Comparing the three marker systems to each other, RAPD and AFLP cophenetic indices were highly correlated (r = 0.59), while correlationcoefficient between RAPD and SSR was r = 0.53 and between SSR andAFLP was r = 0.35. For all markers a relatively high similarity indendrogram topologies was obtained although some differences wereobserved. All the dendrograms, including that obtained by the combineduse of all the marker data, reflect some relationships for most of thepopulations according to their geographic conditions. The results indicatethat single or combined marker system could be used to insight into geneticstudy in P. asperata and the combined data of different marker systems canprovide more reliable information.