Heat capacities of ionic liquids as a function of temperature at 0.1 MPa. measurement and prediction

Heat capacities of nine ionic liquids were measured from (293 to 358) K by using a heat flux differential scanning calorimeter. The impact of impurities (water and chloride content) in the ionic liquid was analyzed to estimate the overall uncertainty. The Joback method for predicting ideal gas heat capacities has been extended to ionic liquids by the generation of contribution parameters for three new groups. The principle of corresponding states has been employed to enable the subsequent calculation of liquid heat capacities for ionic liquids, based on critical properties predicted using the modified Lydersen-Joback-Reid method, as a function of the temperature from (256 to 470) K. A relative absolute deviation of 2.9% was observed when testing the model against 961 data points from 53 different ionic liquids reported previously and measured within this study.

Effect of acetonitrile on the solubility of carbon dioxide in 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) amide

The effect of the addition of acetonitrile on the solubility of carbon dioxide in an ionic liquid, the 1-ethyl-3- methylimidazolium bis(trifluoromethanesulfonyl)amide, [C(2)mim][NTf2], was studied experimentally at pressures close to atmospheric and as a function of temperature between 290 and 335 K. It was observed that the solubility of carbon dioxide decreases linearly with the mole fraction of acetonitrile from a value of 2.6 x 10(-2) in the pure ionic liquid at 303 K to a mole fraction of 1.3 x 10(-2) in the mixture [C(2)mim][NTf2] + CH3CN with x(CH3CN) = 0.77 at the same temperature. The gas solubility decreases with temperature, and the thermodynamic properties of solvation could be calculated. The vapor pressures of the [ C2mim][ NTf2] + CH3CN mixtures were measured in the same temperature range, and strong negative deviations from Raoult's law were obtained: up to 36% for a mixture with x(CH3CN) = 0.46 at 334 K. Negative excess molar volumes of approximately -1 cm(3) mol(-1) at equimolar composition could also be calculated from density measurements of the pure components and of the mixtures. These observations are confirmed by neutron diffraction studies and are compatible with the existence of strong ion-dipole interactions in the mixed liquid solvent.

Formation of Novel Di-Nuclear Lanthanide Luminescent Sm(III), Eu(III) and Tb(III) Triple Stranded Helicates from a C2 Symmetrically 2,6-Dicarboxylic Amide based 1,3-Xylene Ligand in CH3CN

The synthesis of the C2-symmetrical ligand 1 consisting of two naphthalene units connected to two pyridine-2,6-dicarboxamide moieties linked by a xylene spacer and the formation of LnIII-based (Ln1/4 Sm, Eu, Tb, and Lu) dimetallic helicates [Ln2 · 13] in MeCN by means of a metal-directed synthesis is described. By analyzing the metal-induced changes in the absorption and the fluorescence of 1, the formation of the helicates, and the presence of a second species [Ln2 · 12] was confirmed by nonlinear- regression analysis. While significant changes were observed in the photophysical properties of 1, the most dramatic changes were observed in the metal-centred lanthanide emissions, upon excitation of the naphthalene antennae. From the changes in the lanthanide emission, we were able to demonstrate that these helicates were formed in high yields (ca. 90% after the addition of 0.6 equiv. of LnIII), with high binding constants, which matched well with that determined from the changes in the absorption spectra. The formation of the LuIII helicate, [ Lu2 · 13 ] , was also investigated for comparison purposes, as we were unable to obtain accurate binding constants from the changes in the fluorescence emission upon formation of [Sm2 · 13], [Eu2 · 13], and [Tb2 · 13].

Mono- and dimethyl-1,2,4-triazolate as ligands for the mercuric ion in the cationic three-dimensional coordination polymer of [Hg-2(Mmt)(Dmt)(2)](NO3)(H2O))

Colourless crystals of [Hg-2(Mmt)(Dmt)(2)](NO3)(H2O) were obtained from a reaction of mercuric nitrate with nionomethyl- and dimethyl-1,2.4-triazolate (Mmt(-) and Dmt(-), respectively). In the crystal structure (monoclinic, C2/c (no. 15), a = 2579.4(4) b = 1231.1(2), c = 1634.8(2) pm, beta = 128.32(1)degrees V = 4073.3(11).10(6).pm(3): Z = 8, R-1 [I-0 > 2 sigma(I-0)]: 0.0355), half of the mercuric ions are essentially two-coordinate (Hg-N: 210-215 pm), the other half are tetrahedrally surrounded by N-donor atoms (Hg-N: 221, 225 pm) of the Mmt(-) and Dmt(-) anions. These three-N ligands construct a three-dimensional framework.

Species distribution and coordination of uranyl chloro complexes in acetonitrile

The complex formation of the uranyl ion, UO22+, with chloride ions in acetonitrile has been investigated by factor analysis of UV-vis absorption and U L-3 edge EXAFS (extended X-ray absorption fine structure) spectra. As a function of increasing [Cl-]/[UO22+] ratio, the five monomeric species [UO2(H2O)(5)](2+), [UO2Cl(H2O)(2)(MeCN)(2)](+), [UO2Cl2(H2O)(MeCN)(2)], [UO2Cl3(MeCN)(2)](-), and [UO2Cl4](2-) have been observed. The distances determined in the first coordination sphere are: U-O-ax = 1.77 angstrom, U-O-H2O = 2.43 angstrom, U-N-MeCN = 2.53 angstrom, and U-Cl = 2.68 angstrom. A crystalline material has been obtained from the intermediate solution with the [Cl-]/[UO22+] ratio of similar to 2, where [UO2Cl2(H2O)(MeCN)(2)] is the dominating species. The crystal structure analysis of this material revealed a tetrameric complex, [(UO2)(4)(mu(2)-Cl)(4)(mu(3)-O)(2)(H2O)(2)(CH3CN)(4)]center dot(CH3CN). The crystal data are: monoclinic, space group P2(1)/n, a 10.6388(5) angstrom, b = 14.8441(5) angstrom, c = 10.8521(5) angstrom, beta = 109.164(5)degrees, and Z = 2. The U(VI) coordination of the solution species [UO2Cl2(H2O)(MeCN)(2)] changes during the crystallization by replacing one MeCN molecule with a bridging mu(3)-O atom in the tetramer.

YF[MoO4] and YCl[MoO4]: Two halide derivatives of yttrium ortho-oxomolybdate: Syntheses, structures, and luminescence properties

The halide derivatives of yttrium ortho-oxomolybdate YX[MoO4] (X = F, Cl) both crystallize in the monoclinic system with four formula units per unit cell. YF[MoO4] exhibits a primitive cell setting (space group P2(1)/c, a = 519.62(2) pm, b = 1225.14(7) pm, c = 663.30(3) pm, beta = 112.851(4)degrees), whereas the lattice of YCl[MoO4] shows face-centering (space group C2/m; a = 1019.02(5) pm, b = 720.67(4) pm, c = 681.50(3) pm, beta = 107.130(4)degrees). The two compounds each contain crystallographically unique Y3+ cations, which are found to have a coordination environment of six oxide and two halide anions. In the case of YF[MoO4], the coordination environment is seen as square antiprisms, and for YCl[MoO4], trigon-dodecahedra. are found. The discrete tetrahedral [MoO4](2-) units of the fluoride derivative are exclusively bound by six terminal Y3+ cations, while those of the chloride compound show a 5-fold coordination around the tetrahedra with one edge-bridging and four terminal Y3+ cations. The halide anions in each compound exhibit a coordination number of two, building up isolated planar rhombus-shaped units according to [Y2F2](4+) in YF[MoO4] and [Y2Cl2](4+) in YCl[MoO4], respectively. Both compounds were synthesized at high temperatures using Y2O3, MoO3, and the corresponding yttrium trihalide in a molar ratio of 1:3:1. Single crystals of both are insensitive to moist air and are found to be coarse shaped and colorless with optical band gaps situated in the near UV around 3.78 eV for the fluoride and 3.82 eV for the chloride derivative. Furthermore, YF[MoO4] seems to be a suitable material for doping to obtain luminescent materials because the Eu3+-doped compound shows an intense red luminescence, which has been spectroscopically investigated.

A new approach for the detection of ethylene using silica-supported palladium complexes

The coordination of olefins to square-planar Pd(II) and Pt(II) complexes containing 2,9-dimethylphenanthroline (L1) often involves a change of color associated with a change of geometry at the metal center. In order to obtain suitable colorimetric detectors for ethylene gas, a series of new Pd(II) and Pt(II) compounds with a range of 2,9-disubstituted phenanthroline ligands [2,9-di-n-butyl-1,10-phenanthroline (L-2), 2,9-di-s-butyl-1,10-phenanthroline (L3), 2,9-diphenyl-1,10-phenanthroline (L4), and 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (bathocuproine, L5)] have been prepared and their reactivity toward ethylene investigated both in solution and after depositing the detector compounds on a variety of solid supports. The Pd(II) complex [PdCl2(L2)] supported on silica undergoes a clear color change upon exposure to ethylene, while remaining stable toward air and water, and forms the basis for new simple colorimetric detectors with potential applications in ethylene pipe-leak detection and the monitoring of fruit ripening. Encouragingly, the detector is able to discriminate between fruit at different stages of ripening. The response of the detector to other volatiles was also examined, and specific color changes were also observed upon exposure to aromatic acetylenes. The crystal structures of four new derivatives, including the ethylene-Pt(II) complex [PtCl2(C2H4)(L2)], are also described.

The comparison of fac and mer ruthenium(II) trischelate complexes in anion binding

The synthesis of three new homoleptic trischelate ruthenium( II) complexes bearing new 2,2'-bipyridine ligands, 5,5'-dibenzylamido-2,2'-bipyridine (L1) and 5-benzylamido-2,2'- bipyridine (L2) has been achieved. In the case of [Ru(L2)(3)](2+), the mer and fac isomers have been separated. H-1 NMR spectroscopic anion binding studies indicate that the two C-3-symmetric pockets provided by [ Ru(L1)(3)](2+) is conducive to receive a range of anions, although this is not readily reflected in the photophysical behaviour. The fac-isomer of [Ru(L2)(3)](2+) does appear to have an enhancement in the binding interactions over the mer form with dihydrogenphosphate salts, although the difference is much less marked with the spherical chloride ions. From X-ray crystallographic evidence, the ability to hold water in the "anion" binding cleft can inhibit the strength of the interactions with anions, giving rise to the observed selectivity for directional oxoanions such as dihydrogen phosphate.

Liquid-liquid miscibility and volumetric properties of aqueous solutions of ionic liquids as a function of temperature

The volumetric properties of seven {water + ionic liquid} binary mixtures have been studied as a function of temperature from (293 to 343) K. The phase behaviour of the systems was first investigated using a nephelometric method and excess molar volumes were calculated from densities measured using an Anton Paar densimeter and fitted using a Redlich-Kister type equation. Two ionic liquids fully miscible with water (1-butyl-3-methylimidazolium tetrafluoroborate ([CCIm][BF]) and 1-ethyl-3-methylimidazolium ethylsulfate ([CCIm][EtSO])) and five ionic liquids only partially miscible with water (1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([CCIm][NTf]), 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([CCIm][NTf]), 1-butyl-3-methylimidazolium hexafluorophosphate ([CCIm][PF]), 1-butyl-3-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([CCPyrro][NTf]), and butyltrimethylammonium bis(trifluoromethylsulfonyl)imide ([N][NTf])) were chosen. Small excess volumes (less than 0.5 cm · mol at 298 K) are obtained compared with the molar volumes of the pure components (less than 0.3% of the molar volume of the pure ionic liquid). For all the considered systems, except for {[CCIm][EtSO] + water}, positive excess molar volumes were calculated. Finally, an increase of the non-ideality character is observed for all the systems as temperature increases. © 2009 Elsevier Ltd. All rights reserved.

Evaluation of Gas Solubility Prediction in Ionic Liquids using COSMOthermX

As the range of available ionic liquids increases, methods by which important engineering parameters such as gas solubilities can be estimated from simple structural information become ever more desirable. COSMO-based thermodynamic models, such as that used by COSMOthermX, allow the determination of such data for pure and mixed component systems. Herein, we evaluate the predictive capability of COSMOthermX through a comparison with literature data obtained from the IUPAC database which contains data for 15 gases in 27 ionic liquids, To determine any effect inherent to ionic liquids, gas solubility predictions were first performed for selected molecular solvents at constant temperature and pressure. Further estimations of gas solubility at temperatures ranging from (278 to 368) K at 0.1 MPa in water were performed for 14 gases. The Study has demonstrated that COSMOthermX is capable of predicting, qualitatively, gas solubilities in ionic liquids and, hence, reducing the amount of unnecessary experimental measurements prior to specific applications using ionic liquids.

Characterization of silica-supported dodecatungstic heteropolyacids as a function of their dehydroxylation temperature

Dodecatungsto-silicic H4SiW12O40 and -phosphoric acids H3PW12O40 were deposited on silica by a classical impregnation technique. The resulting materials were studied by in situ Raman and infrared spectroscopy, XPS and by solid-state H-1 MAS NMR as a function of their dehydroxylation temperature. The data show that in the case of H3PW12O40 three silanol groups are protonated while in the case of H4SiW12O40 at least one acidic proton remains. Upon heating this proton reacts leading to a disordered structure and a broadening of the W-O Raman bands.

Coordination environment of [UO2Br4](2-) in ionic liquids and crystal structure of [Bmim](2)[UO2Br4]

The complex formed by the reaction of the uranyl ion, UO22+, with bromide ions in the ionic liquids 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Bmiml[Tf2N]) and methyl-tributylammonium bis(trifluoromethylsulfonyl)imide ([MeBu3N][Tf2N]) has been investigated by UV-Vis and U L-III-edge EXAFS spectroscopy and compared to the crystal structure of [Bmim](2)[UO2Br4]. The solid state reveals a classical tetragonal bipyramid geometry for [UO2Br4](2-) with hydrogen bonds between the Bmim(+) and the coordinated bromides. The UV-Vis spectroscopy reveals the quantitative formation of [UO2Br4](2-) when a stoichiometric amount of bromide ions is added to UO2(CF3SO3)(2) in both Tf2N-based ionic liquids. The absorption spectrum also suggests a D-4h symmetry for [UO2Br4](2-) in ionic liquids, as previously observed for the [UO2Cl4](2-) congener. EXAFS analysis supports this conclusion and demonstrates that the [UO2Br4](2-) coordination polyhedron is maintained in the ionic liquids without any coordinating solvent or water molecules. The mean U-O and U-Br distances in the solutions, determined by EXAFS, are, respectively, 1.766(2) and 2.821(2)angstrom in [Bmim][Tf2N], and, respectively, 1.768(2) and 2.827(2) angstrom, in [MeBu3N][Tf2N]. Similar results are obtained in both ionic liquids indicating no significant influence of the ionic liquid cation either on the complexation reaction or on the structure of the uranyl species. (C) 2009 Elsevier Ltd. All rights reserved.

Chromium, iron, ruthenium and gold complexes of 3,3-(biphenyl-2,2 '-diyl)-1-diphenylphosphino-1-phenylallene: A versatile ligand

Successive treatment of 9-(phenylethynyl)fluoren-9-ol (1a), with HBr, butyllithium and chlorodiphenylphosphine furnishes 3,3-(biphenyl-2,2'-diyl)-1-diphenylphosphino-1-phenylallene (5). Moreover, reaction of 1a directly with chlorodiphenylphosphine yields the corresponding allenylphosphine oxide (6). The allenylphosphine (5), and Fe-2(CO)(9) initially form the phosphine-Fe(CO)(4) complex, 11, which is very thermally sensitive and readily loses a carbonyl ligand. In the resulting phosphine-Fe(CO)(3) system, 12, the additional site at iron is coordinated by the allene double bond adjacent to phosphorus; the Fe(CO) 3 tripod in 12 exhibits restricted rotation on the NMR time-scale even at room temperature. The corresponding chromium complex, (5)-Cr(CO)5 (9), has also been prepared. The gold complexes (5)AuCl (13), and [(5)-Au(THT)](+) X-, where (THT) is tetrahydrothiophene, and X = PF6 (14a), or ClO4 (14b), are analogous to the known triphenylphosphine-gold complexes. In contrast, in the (arene)(allenylphosphine) RuCl2 system the allene double bond adjacent to phosphorus displaces a chloride, and the resulting cationic species undergoes nucleophilic attack by water yielding ultimately a five-membered Ru-P-C=C-O ruthenacycle (17). Thus, the allenylphosphine (5), reacts initially as a conventional mono-phosphine but, when the metal centre has a readily displaceable ligand such as a carbonyl or halide, the allene double bond adjacent to the phosphorus can also function as a donor. X- ray crystal structures are reported for 5, 6, 11, 12, 13, 14a, 14b and 17.