A comparative performance study of four-pole induction motors and synchronous reluctance motors in variable speed drives

Design aspects of the Transversally Laminated Anisotropic (TLA) Synchronous Reluctance Motor (SynRM) are studied and the machine performance analysis compared to the Induction Motor (IM) is done. The SynRM rotor structure is designed and manufactured for a30 kW, four-pole, three-phase squirrel cage induction motor stator. Both the IMand SynRM were supplied by a sensorless Direct Torque Controlled (DTC) variablespeed drive. Attention is also paid to the estimation of the power range where the SynRM may compete successfully with a same size induction motor. A technicalloss reduction comparison between the IM and SynRM in variable speed drives is done. The Finite Element Method (FEM) is used to analyse the number, location and width of flux barriers used in a multiple segment rotor. It is sought for a high saliency ratio and a high torque of the motor. It is given a comparison between different FEM calculations to analyse SynRM performance. The possibility to take into account the effect of iron losses with FEM is studied. Comparison between the calculated and measured values shows that the design methods are reliable. A new application of the IEEE 112 measurement method is developed and used especially for determination of stray load losses in laboratory measurements. The study shows that, with some special measures, the efficiency of the TLA SynRM is equivalent to that of a high efficiency IM. The power factor of the SynRM at rated load is smaller than that of the IM. However, at lower partial load this difference decreases and this, probably, brings that the SynRM gets a better power factor in comparison with the IM. The big rotor inductance ratio of the SynRM allows a good estimating of the rotor position. This appears to be very advantageous for the designing of the rotor position sensor-less motor drive. In using the FEM designed multi-layer transversally laminated rotor with damper windings it is possible to design a directly network driven motor without degrading the motorefficiency or power factor compared to the performance of the IM.

Ash Particle Erosion on Steam Boiler Convective Section

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.

Genetic variation for carbon isotope composition in Juglans regia L.: relationships with growth, phenology and climate of origin

Among the traits of breeding interest for the common walnut tree Juglans regia L., characteristics such as timing of budbreak and leaf fall, water-use efficiency and growth performance are regarded as being of utmost relevance in Mediterranean conditions. The authors evaluated intraspecific variation in $\delta$13C (carbon isotope composition, surrogate of intrinsic water-use efficiency, WUE$_{\rm i}$) for 22 J. regia families grown in a progeny test under supplementary irrigation, and investigated whether such variation correlated with climatic indicators of native habitats. The genetic relationships between $\delta$13C, growth and phenology were also assessed during two consecutive years. Overall, the most water-use-efficient families (i.e. with higher $\delta$13C), which originated mainly from drought-prone provenance regions which have a high vapour pressure deficit and low rainfall, exhibited less height growth and smaller DBH. Using a stepwise regression procedure, $\delta$13C was included as the main explanatory variable of genotypic variation in growth traits, together with growing season duration (for DBH in both years) and flushing (for height in 2007). It was concluded that WUE$_{\rm i}$ is largely unconnected to phenology effects in the explanation of growth performance for J. regia, therefore suggesting the opportunity of simultaneously selecting for low WUE$_{\rm i}$ and extended growing period to maximise productivity in non-water-limited environments.

La fonction publique en Suisse : analyse géopolitique d'un fédéralisme à géométrie variable

Bien que présenté comme un modèle de stabilité, le fédéralisme est constamment remis en question. Le but de l'article est de présenter quelques-unes de ses caractéristiques lues à travers les effectifs de la fonction publique en Suisse. Pour ce faire, nous distinguerons quatre types d'employeurs : Confédération, cantons, communes et corporations de droit public, lesquels représentent 10,5 % du total des actifs en Suisse. Nous analyserons la densité administrative, la variation des emplois et le degré de décentralisation selon la culture, le territoire et la religion. Il ressort que la fonction publique intermédiaire, c'est-à-dire les cantons, joue le premier rôle avec ses 140'000 emplois en équivalents plein temps (EPT) sur un total de 328'000, en hausse de 10,3 % par rapport à 2001. Les communes comptent 38 % des agents publics (+3,6 % par rapport à 2001), loin devant la Confédération, 11 % du total (en perte de vitesse : -1,2 %) et les corporations de droit public, 9 % du total (+14,5 %). Le taux d'administration est plus élevé dans la partie francophone que dans la partie germanophone, ainsi que dans les centres économiques et les zones frontières. Les écarts entre les cantons peuvent varier du simple au triple. En fait, deux modèles politico-administratifs transparaissent : le premier « cantonaliste » et davantage étatiste dans la partie latine, l'autre « communaliste » et décentralisé, dominant dans la partie germanophone. Le quotient de décentralisation administrative montre de grandes différences entre l'est et l'ouest, qui s'estompent toutefois avec la modernisation des institutions et le repositionnement de la Suisse face à l'Europe.

Effects of gluten and transglutaminase on microstructure, sensory characteristics and instrumental texture of oat bread

Selostus: Taikinaan lisättyjen gluteenin ja transglutaminaasin vaikutus kauraleivän rakenteeseen

Lack of support for the association between facial shape and aggression: a reappraisal based on a worldwide population genetics perspective

Antisocial and criminal behaviors are multifactorial traits whose interpretation relies on multiple disciplines. Since these interpretations may have social, moral and legal implications, a constant review of the evidence is necessary before any scientific claim is considered as truth. A recent study proposed that men with wider faces relative to facial height (fWHR) are more likely to develop unethical behaviour mediated by a psychological sense of power. This research was based on reports suggesting that sexual dimorphism and selection would be responsible for a correlation between fWHR and aggression. Here we show that 4,960 individuals from 94 modern human populations belonging to a vast array of genetic and cultural contexts do not display significant amounts of fWHR sexual dimorphism. Further analyses using populations with associated ethnographical records as well as samples of male prisoners of the Mexico City Federal Penitentiary condemned by crimes of variable level of inter-personal aggression (homicide, robbery, and minor faults) did not show significant evidence, suggesting that populations/individuals with higher levels of bellicosity, aggressive behaviour, or power-mediated behaviour display greater fWHR. Finally, a regression analysis of fWHR on individual"s fitness showed no significant correlation between this facial trait and reproductive success. Overall, our results suggest that facial attributes are poor predictors of aggressive behaviour, or at least, that sexual selection was weak enough to leave a signal on patterns of between- and within-sex and population facial variation.

Relating microstructure, sensory and instrumental texture of processed oat

Selostus: Prosessoidun kauran mikroskooppinen ja aistittava rakenne

Local Salmonella immunostimulation recruits vaccine-specific CD8 T cells and increases regression of bladder tumor.

NlmCategory="UNASSIGNED">The efficacy of antitumoral responses can be increased using combinatorial vaccine strategies. We recently showed that vaccination could be optimized by local administration of diverse molecular or bacterial agents to target and augment antitumoral CD8 T cells in the genital mucosa (GM) and increase regression of cervical cancer in an animal model. Non muscle-invasive bladder cancer is another disease that is easily amenable to local therapies. In contrast to data obtained in the GM, in this study we show that intravesical (IVES) instillation of synthetic toll-like receptor (TLR) agonists only modestly induced recruitment of CD8 T cells to the bladder. However, IVES administration of Ty21a, a live bacterial vaccine against typhoid fever, was much more effective and increased the number of total and vaccine-specific CD8 T cells in the bladder approximately 10 fold. Comparison of chemokines induced in the bladder by either CpG (a TLR-9 agonist) or Ty21a highlighted the preferential increase in complement component 5a, CXCL5, CXCL2, CCL8, and CCL5 by Ty21a, suggesting their involvement in the attraction of T cells to the bladder. IVES treatment with Ty21a after vaccination also significantly increased tumor regression compared to vaccination alone, resulting in 90% survival in an orthotopic murine model of bladder cancer expressing a prototype tumor antigen. Our data demonstrate that combining vaccination with local immunostimulation may be an effective treatment strategy for different types of cancer and also highlight the great potential of the Ty21a vaccine, which is routinely used worldwide, in such combinatorial therapies.

La perspectiva narrativa en Nubosidad variable de Carmen Martín Gaite

La publicación en 1992 de Nubosidad variable supuso la reanudación de la actividad novelesca de Carmen Martín Gaite, después de catorce arios dedicados al ensayo y a la historia. En esta obra, el «credo» literario de la novelista no ha variado sustancialmente en relación a otras como Ritmo lento, Retahilas o El cuarto de atrás, pero se ha visto enriquecido con una técnica que acota y fija de forma maestra todo el mundo de significaciones que se proyecta, y que podemos conceptualizar como el flirteo de la autora con la introspección, el recuerdo, y los antojos frente al tiempo pasado de una memoria vulnerable y resbaladiza. La perspectiva narrativa se revela, en este sentido, como el apoyo básico del andamiaje material de la obra.

Bystander responses to a violent incident in an immersive virtual environment

Under what conditions will a bystander intervene to try to stop a violent attack by one person on another? It is generally believed that the greater the size of the crowd of bystanders, the less the chance that any of them will intervene. A complementary model is that social identity is critical as an explanatory variable. For example, when the bystander shares common social identity with the victim the probability of intervention is enhanced, other things being equal. However, it is generally not possible to study such hypotheses experimentally for practical and ethical reasons. Here we show that an experiment that depicts a violent incident at life-size in immersive virtual reality lends support to the social identity explanation. 40 male supporters of Arsenal Football Club in England were recruited for a two-factor between-groups experiment: the victim was either an Arsenal supporter or not (in-group/out-group), and looked towards the participant for help or not during the confrontation. The response variables were the numbers of verbal and physical interventions by the participant during the violent argument. The number of physical interventions had a significantly greater mean in the ingroup condition compared to the out-group. The more that participants perceived that the Victim was looking to them for help the greater the number of interventions in the in-group but not in the out-group. These results are supported by standard statistical analysis of variance, with more detailed findings obtained by a symbolic regression procedure based on genetic programming. Verbal interventions made during their experience, and analysis of post-experiment interview data suggest that in-group members were more prone to confrontational intervention compared to the out-group who were more prone to make statements to try to diffuse the situation.

Systematic analysis of factors associated with progression and regression of ulcerative colitis in 918 patients.

BACKGROUND: Studies that systematically assess change in ulcerative colitis (UC) extent over time in adult patients are scarce. AIM: To assess changes in disease extent over time and to evaluate clinical parameters associated with this change. METHODS: Data from the Swiss IBD cohort study were analysed. We used logistic regression modelling to identify factors associated with a change in disease extent. RESULTS: A total of 918 UC patients (45.3% females) were included. At diagnosis, UC patients presented with the following disease extent: proctitis [199 patients (21.7%)], left-sided colitis [338 patients (36.8%)] and extensive colitis/pancolitis [381 (41.5%)]. During a median disease duration of 9 [4-16] years, progression and regression was documented in 145 patients (15.8%) and 149 patients (16.2%) respectively. In addition, 624 patients (68.0%) had a stable disease extent. The following factors were identified to be associated with disease progression: treatment with systemic glucocorticoids [odds ratio (OR) 1.704, P = 0.025] and calcineurin inhibitors (OR: 2.716, P = 0.005). No specific factors were found to be associated with disease regression. CONCLUSIONS: Over a median disease duration of 9 [4-16] years, about two-thirds of UC patients maintained the initial disease extent; the remaining one-third had experienced either progression or regression of the disease extent.

Taloudellinen lisäarvo ja suhdanne-vaihtelut

Tutkimusongelmana oli ratkaista onko taloudellisella lisäarvolla ja suhdannevaihteluilla yhteyttä ja selittääkö suhdannevaihtelut taloudellisen lisäarvon vaihteluja. Empiirisenä aineistona oli 79 suomalaista pörssiyritystä, (kuljetus- ja huolinta, metalli- ja metsäteollisuus sekä auto- ja vähittäiskauppa). Tutkimusperiodina olivat vuodet 1986-2000. Tilastollisena tutkimusmenetelmänä oli regressioanalyysi, jossa selitettävänä muuttujana oli taloudellinen lisäarvo ja selittävänä muuttujana oli bruttokansantuoteprosentti. Analyysit tehtiin toimialamediaanina. Regressiomallin tulosten mukaan suhdannevaihtelut selittävät hyvin kuljetus- ja huolinta-alan yritysten taloudellisen lisäarvon vaihteluita. Metalliteollisuuden- ja autokaupan yritysten taloudelliset lisäarvot korreloivat jonkin verran suhdannevaihteluiden kanssa. Vähittäiskauppa ja metsäteollisuus eivät korreloineet suhdannevaihteluiden kanssa ollenkaan.