Accurate analytical approximation of asteroid deflection with constant tangential thrust

We present analytical formulas to estimate the variation of achieved deflection for an Earth-impacting asteroid following a continuous tangential low-thrust deflection strategy. Relatively simple analytical expressions are obtained with the aid of asymptotic theory and the use of Peláez orbital elements set, an approach that is particularly suitable to the asteroid deflection problem and is not limited to small eccentricities. The accuracy of the proposed formulas is evaluated numerically showing negligible error for both early and late deflection campaigns. The results will be of aid in planning future low-thrust asteroid deflection missions

Effect of impacting radius of curvature on firmness sensing of fruits in a sorting system.

Fruits of two varieties of both apples and pear were tested to measure their response to small energy impact applied by a impact tester with two spherical tips of different radious of curvature ( RA = 2.48 cm and RB = 0.98 cm) and equal mass were used. In the four varieties studied, the size of bruise was smaller with a spherical tip RA than with tip RB . The non-destructive impact test would cause less damage with a spherical impactor with a radious bigger than 0.98 cm.

Experimental study on bridge damage identification based on wavelet packet energy curvature difference method

Among those damage identification methods, the Wavelet Packet Energy Curvature Difference (WPECD) Method is an effective one. However, most of the existing methods rely on numerical simulation and are unverified via experiment, and very few of them have been applied to practice. In this paper, the validity of WPECD in structural damage identification is verified by a numerical example. A damage simulation experiment is taken on a real replaced girder at the Ziya River New Bridge in Cangzhou. Two damage cases are applied and the acceleration responses at the measuring points are obtained, based on which the damages are identified with the WPECD Method, and the influence of wavelet function and decomposition level is studied. The results show that the WPECD Method can identify structure damage efficiently and can be put into practice.

Jupiter power generation with electrodynamic tethers at constant orbital energy

An electrodynamic tether system for power generation at Jupiter is presented that allows extracting energy from Jupiter's corotating plasmasphere while leaving the system orbital energy unaltered to first order. The spacecraft is placed in a polar orbit with the tether spinning in the orbital plane so that the resulting Lorentz force, neglecting Jupiter's magnetic dipole tilt, is orthogonal to the instantaneous velocity vector and orbital radius, hence affecting orbital inclination rather than orbital energy. In addition, the electrodynamic tether subsystem, which consists of two radial tether arms deployed from the main central spacecraft, is designed in such a way as to extract maximum power while keeping the resulting Lorentz torque constantly null. The power-generation performance of the system and the effect on the orbit inclination is evaluated analytically for different orbital conditions and verified numerically. Finally, a thruster-based inclination-compensation maneuver at apoapsis is added, resulting in an efficient scheme to extract energy from the plasmasphere of the planet with minimum propellant consumption and no inclination change. A tradeoff analysis is conducted showing that, depending on tether size and orbit characteristics, the system performance can be considerably higher than conventional power-generation methods.

Einstein-like geometric structures on surfaces

An AH (affine hypersurface) structure is a pair comprising a projective equivalence class of torsion-free connections and a conformal structure satisfying a compatibility condition which is automatic in two dimensions. They generalize Weyl structures, and a pair of AH structures is induced on a co-oriented non-degenerate immersed hypersurface in flat affine space. The author has defined for AH structures Einstein equations, which specialize on the one hand to the usual Einstein Weyl equations and, on the other hand, to the equations for affine hyperspheres. Here these equations are solved for Riemannian signature AH structures on compact orientable surfaces, the deformation spaces of solutions are described, and some aspects of the geometry of these structures are related. Every such structure is either Einstein Weyl (in the sense defined for surfaces by Calderbank) or is determined by a pair comprising a conformal structure and a cubic holomorphic differential, and so by a convex flat real projective structure. In the latter case it can be identified with a solution of the Abelian vortex equations on an appropriate power of the canonical bundle. On the cone over a surface of genus at least two carrying an Einstein AH structure there are Monge-Amp`ere metrics of Lorentzian and Riemannian signature and a Riemannian Einstein K"ahler affine metric. A mean curvature zero spacelike immersed Lagrangian submanifold of a para-K"ahler four-manifold with constant para-holomorphic sectional curvature inherits an Einstein AH structure, and this is used to deduce some restrictions on such immersions.

On a parabolic-elliptic chemotactic system with non-constant chemotactic sensitivity

We study a parabolic–elliptic chemotactic system describing the evolution of a population’s density “u” and a chemoattractant’s concentration “v”. The system considers a non-constant chemotactic sensitivity given by “χ(N−u)”, for N≥0, and a source term of logistic type “λu(1−u)”. The existence of global bounded classical solutions is proved for any χ>0, N≥0 and λ≥0. By using a comparison argument we analyze the stability of the constant steady state u=1, v=1, for a range of parameters. – For N>1 and Nλ>2χ, any positive and bounded solution converges to the steady state. – For N≤1 the steady state is locally asymptotically stable and for χN<λ, the steady state is globally asymptotically stable.

Conductancia del mesófilo en especies forestales: implicaciones en la respuesta fotosintética a la disponibilidad de agua y luz

La fotosíntesis es el proceso biológico que permite la producción primaria y, por tanto, la vida en nuestro planeta. La tasa fotosintética viene determinada por la ‘maquinaria’ bioquímica y las resistencias difusivas al paso del CO2 desde la atmósfera hasta su fijación en el interior de los cloroplastos. Históricamente la mayor resistencia difusiva se ha atribuido al cierre estomático, sin embargo ahora sabemos, debido a las mejoras en las técnicas experimentales, que existe también una resistencia grande que se opone a la difusión del CO2 desde los espacios intercelulares a los lugares de carboxilación. Esta resistencia, llamada normalmente por su inversa: la conductancia del mesófilo (gm), puede ser igual o incluso superior a la resistencia debida por el cierre estomático. En la presente tesis doctoral he caracterizado la limitación que ejerce la resistencia del mesófilo a la fijación de CO2 en diversas especies forestales y en distintos momentos de su ciclo biológico. En la fase de regenerado, hemos estudiado tres situaciones ambientales relevantes en el mayor éxito de su supervivencia, que son: el déficit hídrico, su interacción con la irradiancia y el paso del crecimiento en la sombra a mayor irradiancia, como puede suceder tras la apertura de un hueco en el dosel forestal. En la fase de arbolado adulto se ha caracterizado el estado hídrico y el intercambio gaseoso en hojas desarrolladas a distinta irradiancia dentro del dosel vegetal durante tres años contrastados en pluviometría. Para cada tipo de estudio se han empleado las técnicas ecofisiológicas más pertinentes para evaluar el estado hídrico y el intercambio gaseoso. Por su complejidad y la falta de un método que permita su cuantificación directa, la gm ha sido evaluada por los métodos más usados, que son: la discriminación isotópica del carbono 13, el método de la J variable, el método de la J constante y el método de la curvatura. Los resultados más significativos permiten concluir que la limitación relativa a la fotosíntesis por la conductancia estomática, del mesófilo y bioquímica es dependiente de la localización de la hoja en el dosel forestal. Por primera vez se ha documentado que bajo estrés hídrico las hojas desarrolladas a la sombra estuvieron más limitadas por una reducción en la gm, mientras que las hojas desarrolladas a pleno sol estuvieron más limitadas por reducción mayor de la conductancia estomática (gsw). Encontramos buena conexión entre el aparato fotosintético foliar y el sistema hídrico debido al alto grado de correlación entre la conductancia hidráulica foliar aparente y la concentración de CO2 en los cloroplastos en distintas especies forestales. Además, hemos mostrado diferentes pautas de regulación del intercambio gaseoso según las particularidades ecológicas de las especies estudiadas. Tanto en brinzales crecidos de forma natural y en el arbolado adulto como en plántulas cultivadas en el invernadero la ontogenia afectó a las limitaciones de la fotosíntesis producidas por estrés hídrico, resultando que las limitaciones estomáticas fueron dominantes en hojas más jóvenes mientras que las no estomáticas en hojas más maduras. La puesta en luz supuso un gran descenso en la gm durante los días siguientes a la transferencia, siendo este efecto mayor según el grado de sombreo previo en el que se han desarrollado las hojas. La aclimatación de las hojas a la alta irradiancia estuvo ligada a las modificaciones anatómicas foliares y al estado de desarrollo de la hoja. El ratio entre la gm/gsw determinó la mayor eficiencia en el uso del agua y un menor estado oxidativo durante la fase de estrés hídrico y su posterior rehidratación, lo cual sugiere el uso de este ratio en los programas de mejora genética frente al estrés hídrico. Debido a que la mayoría de modelos de estimación de la producción primaria bruta (GPP) de un ecosistema no incluye la gm, los mismos están incurriendo en una sobreestimación del GPP particularmente bajo condiciones de estrés hídrico, porque más de la mitad de la reducción en fotosíntesis en hojas desarrolladas a la sombra se debe a la reducción en gm. Finalmente se presenta un análisis de la importancia en las estimas de la gm bajo estrés hídrico de la refijación del CO2 emitido en la mitocondria a consecuencia de la fotorrespiración y la respiración mitocondrial en luz. ABSTRACT Photosynthesis is the biological process that supports primary production and, therefore, life on our planet. Rates of photosynthesis are determined by biochemical “machinery” and the diffusive resistance to the transfer of CO2 from the atmosphere to the place of fixation within the chloroplasts. Historically the largest diffusive resistance was attributed to the stomata, although we now know via improvements in experimental techniques that there is also a large resistance from sub-stomatal cavities to sites of carboxylation. This resistance, commonly quantified as mesophyll conductance (gm), can be as large or even larger than that due to stomatal resistance. In the present PhD I have characterized the limitation exerted by the mesophyll resistance to CO2 fixation in different forest species at different stages of their life cycle. In seedlings, we studied three environmental conditions that affect plant fitness, namely, water deficit, the interaction of water deficit with irradiance, and the transfer of plants grown in the shade to higher irradiance as can occur when a gap opens in the forest canopy. At the stage of mature trees we characterized water status and gas exchange in leaves developed at different irradiance within the canopy over the course of three years that had contrasting rainfall. For each study we used the most relevant ecophysiological techniques to quantify water relations and gas exchange. Due to its complexity and the lack of a method that allows direct quantification, gm was estimated by the most commonly used methods which are: carbon isotope discrimination, the J-variable, constant J and the curvature method The most significant results suggest that the relative limitation of photosynthesis by stomata, mesophyll and biochemistry depending on the position of the leaf within the canopy. For the first time it was documented that under water stress shaded leaves were more limited by a reduction in gm, while the sun-adapted leaves were more limited by stomatal conductance (gsw). The connection between leaf photosynthetic apparatus and the hydraulic system was shown by the good correlations found between the apparent leaf hydraulic conductance and the CO2 concentration in the chloroplasts in shade- and sun-adapted leaves of several tree species. In addition, we have revealed different patterns of gas exchange regulation according to the functional ecology of the species studied. In field grown trees and greenhouse-grown seedlings ontogeny affected limitations of photosynthesis due to water stress with stomatal limitations dominating in young leaves and nonstomatal limitations in older leaves. The transfer to high light resulted in major decrease of gm during the days following the transfer and this effect was greater as higher was the shade which leaves were developed. Acclimation to high light was linked to the leaf anatomical changes and the state of leaf development. The ratio between the gm/gsw determined the greater efficiency in water use and reduced the oxidative stress during the water stress and subsequent rehydration, suggesting the use of this ratio in breeding programs aiming to increase avoidance of water stress. Because most models to estimate gross primary production (GPP) of an ecosystem do not include gm, they are incurring an overestimation of GPP particularly under conditions of water stress because more than half of An decrease in shade-developed leaves may be due to reduction in gm. Finally, we present an analysis of the importance of how estimates of gm under water stress are affected by the refixation of CO2 that is emitted from mitochondria via photorespiration and mitochondrial respiration in light.

Measurement of the intrinsic damping constant in individual nanodisks of Y3Fe5O12 and Y3Fe5O12|Pt

We report on an experimental study on the spin-waves relaxation rate in two series of nanodisks of diameter ϕ=300 , 500, and 700 nm, patterned out of two systems: a 20 nm thick yttrium iron garnet (YIG) film grown by pulsed laser deposition either bare or covered by 13 nm of Pt. Using a magnetic resonance force microscope, we measure precisely the ferromagnetic resonance linewidth of each individual YIG and YIG|Pt nanodisks. We find that the linewidth in the nanostructure is sensibly smaller than the one measured in the extended film. Analysis of the frequency dependence of the spectral linewidth indicates that the improvement is principally due to the suppression of the inhomogeneous part of the broadening due to geometrical confinement, suggesting that only the homogeneous broadening contributes to the linewidth of the nanostructure. For the bare YIG nano-disks, the broadening is associated to a damping constant α=4 × 10−4 . A threefold increase of the linewidth is observed for the series with Pt cap layer, attributed to the spin pumping effect. The measured enhancement allows to extract the spin mixing conductance found to be G↑↓=1.55 × 1014 Ω−1 m−2 for our YIG(20nm)|Pt interface, thus opening large opportunities for the design of YIG based nanostructures with optimized magnetic losses.

Methodology of quantifying curvature of Fresnel lenses and its effect on CPV module performance

Fresnel lenses used as primary optics in concentrating photovoltaic modules may show warping produced by lens manufacturing or module assembly (e.g., stress during molding or weight load) or due to stress during operation (e.g., mismatch of thermal expansion between different materials). To quantify this problem, a simple method called “checkerboard method” is presented. The proposed method identifies shape errors on the front surface of primary lenses by analyzing the Fresnel reflections. This paper also deals with the quantification of the effects these curvatures have on their optical performance and on the electrical performance of concentrating modules incorporating them. This method can be used to perform quality control of Fresnel lenses in scenarios of high volume production.

Evolución del conocimiento del hormigón estructural hasta 1973

Esta tesis analiza los criterios con que fueron proyectadas y construidas las estructuras de hormigón hasta 1973, fecha coincidente con la Instrucción EH-73, que en contenido, formato y planteamiento, consagró la utilización de los criterios modernamente utilizados hasta ahora. Es heredera, además, de las CEB 1970. Esos años marcan el cambio de planteamiento desde la Teoría Clásica hacia los Estados Límite. Los objetivos perseguidos son, sintéticamente: 1) Cubrir un vacío patente en el estudio de la evolución del conocimiento. Hay tratados sobre la historia del hormigón que cubren de manera muy completa el relato de personajes y realizaciones, pero no, al menos de manera suficiente, la evolución del conocimiento. 2) Servir de ayuda a los técnicos de hoy para entender configuraciones estructurales, geometrías, disposiciones de armado, formatos de seguridad, etc, utilizados en el pasado, lo que servirá para la redacción más fundada de dictámenes preliminares sobre estructuras existentes. 3) Ser referencia para la realización de estudios de valoración de la capacidad resistente de construcciones existentes, constituyendo la base de un documento pre-normativo orientado en esa dirección. En efecto, esta tesis pretende ser una ayuda para los ingenieros de hoy que se enfrentan a la necesidad de conservar y reparar estructuras de hormigón armado que forman parte del patrimonio heredado. La gran mayoría de las estructuras, fueron construidas hace más de 40 años, por lo que es preciso conocer los criterios que marcaron su diseño, su cálculo y su construcción. Pretende determinar cuáles eran los límites de agotamiento y por tanto de seguridad, de estructuras dimensionadas con criterios de antaño, analizadas por la metodología de cálculo actual. De este modo, se podrá determinar el resguardo existente “real” de las estructuras dimensionadas y calculadas con criterios “distintos” a los actuales. Conocer el comportamiento de las estructuras construidas con criterios de la Teoría Clásica, según los criterios actuales, permitirá al ingeniero de hoy tratar de la forma más adecuada el abanico de necesidades que se puedan presentar en una estructura existente. Este trabajo se centra en la evolución del conocimiento por lo que no se encuentran incluidos los procesos constructivos. En lo relativo a los criterios de proyecto, hasta mediados del siglo XX, éstos se veían muy influidos por los ensayos y trabajos de autor consiguientes, en los que se basaban los reglamentos de algunos países. Era el caso del reglamento prusiano de 1904, de la Orden Circular francesa de 1906, del Congreso de Lieja de 1930. A partir de la segunda mitad del siglo XX, destacan las aportaciones de ingenieros españoles como es el caso de Alfredo Páez Balaca, Eduardo Torroja y Pedro Jiménez Montoya, entre otros, que permitieron el avance de los criterios de cálculo y de seguridad de las estructuras de hormigón, hasta los que se conocen hoy. El criterio rector del proyecto de las estructuras de hormigón se fundó, como es sabido, en los postulados de la Teoría Clásica, en particular en el “momento crítico”, aquel para el que hormigón y acero alcanzan sus tensiones admisibles y, por tanto, asegura el máximo aprovechamiento de los materiales y sin pretenderlo conscientemente, la máxima ductilidad. Si el momento solicitante es mayor que el crítico, se dispone de armadura en compresión. Tras el estudio de muchas de las estructuras existentes de la época por el autor de esta tesis, incluyendo entre ellas las Colecciones Oficiales de Puentes de Juan Manuel de Zafra, Eugenio Ribera y Carlos Fernández Casado, se concluye que la definición geométrica de las mismas no se corresponde exactamente con la resultante del momento crítico, dado que como ahora resultaba necesario armonizar los criterios de armado a nivel sección con la organización de la ferralla a lo largo de los diferentes elementos estructurales. Los parámetros de cálculo, resistencias de los materiales y formatos de seguridad, fueron evolucionando con los años. Se fueron conociendo mejor las prestaciones de los materiales, se fue enriqueciendo la experiencia de los propios procesos constructivos y, en menor medida, de las acciones solicitantes y, consiguientemente, acotándose las incertidumbres asociadas lo cual permitió ir ajustando los coeficientes de seguridad a emplear en el cálculo. Por ejemplo, para el hormigón se empleaba un coeficiente de seguridad igual a 4 a finales del siglo XIX, que evolucionó a 3,57 tras la publicación de la Orden Circular francesa de 1906, y a 3, tras la Instrucción española de 1939. En el caso del acero, al ser un material bastante más conocido por cuanto se había utilizado muchísimo previamente, el coeficiente de seguridad permaneció casi constante a lo largo de los años, con un valor igual a 2. Otra de las causas de la evolución de los parámetros de cálculo fue el mejor conocimiento del comportamiento de las estructuras merced a la vasta tarea de planificación y ejecución de ensayos, con los estudios teóricos consiguientes, realizados por numerosos autores, principalmente austríacos y alemanes, pero también norteamericanos y franceses. En cuanto a los criterios de cálculo, puede sorprender al técnico de hoy el conocimiento que tenían del comportamiento del hormigón desde los primeros años del empleo del mismo. Sabían del comportamiento no lineal del hormigón, pero limitaban su trabajo a un rango de tensióndeformación lineal porque eso aseguraba una previsión del comportamiento estructural conforme a las hipótesis de la Elasticidad Lineal y de la Resistencia de Materiales, muy bien conocidas a principios del s. XX (no así sucedía con la teoría de la Plasticidad, aún sin formular, aunque estaba implícita en los planteamientos algunos ingenieros especializados en estructuras de fábrica (piedra o ladrillo) y metálicas. Además, eso permitía independizar un tanto el proyecto de los valores de las resistencias reales de los materiales, lo que liberaba de la necesidad de llevar a cabo ensayos que, en la práctica, apenas se podían hacer debido a la escasez de los laboratorios. Tampoco disponían de programas informáticos ni de ninguna de las facilidades de las que hoy se tienen, que les permitiera hacer trabajar al hormigón en un rango no lineal. Así, sabia y prudentemente, limitaban las tensiones y deformaciones del material a un rango conocido. El modus operandi seguido para la elaboración de esta tesis, ha sido el siguiente: -Estudio documental: se han estudiado documentos de autor, recomendaciones y normativa generada en este ámbito, tanto en España como con carácter internacional, de manera sistemática con arreglo al índice del documento. En este proceso, se han detectado lagunas del conocimiento (y su afección a la seguridad estructural, en su caso) y se han identificado las diferencias con los procedimientos de hoy. También ha sido necesario adaptar la notación y terminología de la época a los criterios actuales, lo que ha supuesto una dificultad añadida. -Desarrollo del documento: A partir del estudio previo se han ido desarrollando los siguientes documentos, que conforman el contenido de la tesis: o Personajes e instituciones relevantes por sus aportaciones al conocimiento de las estructuras de hormigón (investigación, normativa, docencia). o Caracterización de las propiedades mecánicas de los materiales (hormigón y armaduras), en relación a sus resistencias, diagramas tensión-deformación, módulos de deformación, diagramas momento-curvatura, etc. Se incluye aquí la caracterización clásica de los hormigones, la geometría y naturaleza de las armaduras, etc. o Formatos de seguridad: Se trata de un complejo capítulo del que se pretende extraer la información suficiente que permita a los técnicos de hoy entender los criterios utilizados entonces y compararlos con los actuales. o Estudio de secciones y piezas sometidas a tensiones normales y tangenciales: Se trata de presentar la evolución en el tratamiento de la flexión simple y compuesta, del cortante, del rasante, torsión, etc. Se tratan también en esta parte del estudio aspectos que, no siendo de preocupación directa de los técnicos de antaño (fisuración y deformaciones), tienen hoy mayor importancia frente a cambios de usos y condiciones de durabilidad. o Detalles de armado: Incluye el tratamiento de la adherencia, el anclaje, el solapo de barras, el corte de barras, las disposiciones de armado en función de la geometría de las piezas y sus solicitaciones, etc. Es un capítulo de importancia obvia para los técnicos de hoy. Se incluye un anejo con las referencias más significativas a los estudios experimentales en que se basaron las propuestas que han marcado hito en la evolución del conocimiento. Finalmente, junto a las conclusiones más importantes, se enuncian las propuestas de estudios futuros. This thesis analyzes the criteria with which structures of reinforced concrete have been designed and constructed prior to 1973. Initially, the year 1970 was chosen as starting point, coinciding with the CEB recommendations, but with the development of the thesis it was decided that 1973 was the better option, coinciding with the Spanish regulations of 1973, whose content, format and description introduced the current criteria. The studied period includes the Classic Theory. The intended goals of this thesis are: 1) To cover a clear gap in the study of evolution of knowledge about reinforced concrete. The concept and accomplishments achieved by reinforced concrete itself has been treated in a very complete way by the main researchers in this area, but not the evolution of knowledge in this subject area. 2) To help the engineers understand structural configurations, geometries, dispositions of steel, safety formats etc, that will serve as preliminary judgments by experts on existing structures. To be a reference to the existing studies about the valuation of resistant capacity of existing constructions, constituting a basic study of a pre-regulation document. This thesis intends to be a help for the current generation of engineers who need to preserve and repair reinforced concrete structures that have existed for a significant number of years. Most of these structures in question were constructed more than 40 years ago, and it is necessary to know the criteria that influenced their design, the calculation and the construction. This thesis intends to determine the safety limits of the old structures and analyze them in the context of the current regulations and their methodology. Thus, it will then be possible to determine the safety of these structures, after being measured and calculated with the current criteria. This will allow the engineers to optimize the treatment of such a structure. This work considers the evolution of the knowledge, so constructive methods are not included. Related to the design criteria, there existed until middle of the 20th century a large number of diverse European tests and regulations, such as the Prussian norm of 1904, the Circular French Order of 1906, the Congress of Liège of 1930, as well as individual engineers’ own notes and criteria which incorporated the results of their own tests. From the second half of the 20th century, the contributions of Spanish engineers as Alfredo Páez Balaca, Eduardo Torroja and Pedro Jiménez Montoya, among others, were significant and this allowed the advancement of the criteria of the calculation of safety standards of concrete structures, many of which still exist to the present day. The design and calculation of reinforced concrete structures by the Classic Theory, was based on the ‘Critical Bending Moment’, when concrete and steel achieve their admissible tensions, that allows the best employment of materials and the best ductility. If the bending moment is major than the critical bending moment, will be necessary to introduce compression steel. After the study of the designs of many existing structures of that time by the author of this thesis, including the Historical Collections of Juan Manuel de Zafra, Eugenio Ribera and Carlos Fernandez Casado, the conclusion is that the geometric definition of the structures does not correspond exactly with the critical bending moment inherent in the structures. The parameters of these calculations changed throughout the years. The principal reason that can be outlined is that the materials were improving gradually and the number of calculated uncertainties were decreasing, thus allowing the reduction of the safety coefficients to use in the calculation. For example, concrete used a coefficient of 4 towards the end of the 19th century, which evolved to 3,57 after the publication of the Circular French Order of 1906, and then to 3 after the Spanish Instruction of 1939. In the case of the steel, a much more consistent material, the safety coefficient remained almost constant throughout the years, with a value of 2. Other reasons related to the evolution of the calculation parameters were that the tests and research undertaken by an ever-increasing number of engineers then allowed a more complete knowledge of the behavior of reinforced concrete. What is surprising is the extent of knowledge that existed about the behavior of the concrete from the outset. Engineers from the early years knew that the behavior of the concrete was non-linear, but they limited the work to a linear tension-deformation range. This was due to the difficulties of work in a non-linear range, because they did not have laboratories to test concrete, or facilities such as computers with appropriate software, something unthinkable today. These were the main reasons engineers of previous generations limited the tensions and deformations of a particular material to a known range. The modus operandi followed for the development of this thesis is the following one: -Document study: engineers’ documents, recommendations and regulations generated in this area, both from Spain or overseas, have been studied in a systematic way in accordance with the index of the document. In this process, a lack of knowledge has been detected concerning structural safety, and differences to current procedures have been identified and noted. Also, it has been necessary to adapt the notation and terminology of the Classic Theory to the current criteria, which has imposed an additional difficulty. -Development of the thesis: starting from the basic study, the next chapters of this thesis have been developed and expounded upon: o People and relevant institutions for their contribution to the knowledge about reinforced concrete structures (investigation, regulation, teaching). Determination of the mechanical properties of the materials (concrete and steel), in relation to their resistances, tension-deformation diagrams, modules of deformation, moment-curvature diagrams, etc. Included are the classic characterizations of concrete, the geometry and nature of the steel, etc. Safety formats: this is a very difficult chapter from which it is intended to provide enough information that will then allow the present day engineer to understand the criteria used in the Classic Theory and then to compare them with the current theories. Study of sections and pieces subjected to normal and tangential tensions: it intends to demonstrate the evolution in the treatment of the simple and complex flexion, shear, etc. Other aspects examined include aspects that were not very important in the Classic Theory but currently are, such as deformation and fissures. o Details of reinforcement: it includes the treatment of the adherence, the anchorage, the lapel of bars, the cut of bars, the dispositions of reinforcement depending on the geometry of the pieces and the solicitations, etc. It is a chapter of obvious importance for current engineers. The document will include an annex with the most references to the most significant experimental studies on which were based the proposals that have become a milestone in the evolution of knowledge in this area. Finally, there will be included conclusions and suggestions of future studies. A deep study of the documentation and researchers of that time has been done, juxtaposing their criteria and results with those considered relevant today, and giving a comparison between the resultant safety standards according to the Classic Theory criteria and currently used criteria. This thesis fundamentally intends to be a guide for engineers who have to treat or repair a structure constructed according to the Classic Theory criteria.

Phalangeal curvature and positional behavior in extinct sloth lemurs (Primates, Palaeopropithecidae)

Recent paleontological discoveries in Madagascar document the existence of a diverse clade of palaeopropithecids or “sloth lemurs”: Mesopropithecus (three species), Babakotia (one species), Palaeopropithecus (three species), and Archaeoindris (one species). This mini-radiation of now extinct (“subfossil”) lemurs is most closely related to the living indrids (Indri, Propithecus, and Avahi). Whereas the extant indrids are known for their leaping acrobatics, the palaeopropithecids (except perhaps for the poorly known giant Archaeoindris) exhibit numerous skeletal design features for antipronograde or suspensory positional behaviors (e.g., high intermembral indices and mobile joints). Here we analyze the curvature of the proximal phalanges of the hands and feet. Computed as the included angle (θ), phalangeal curvature develops in response to mechanical use and is known to be correlated in primates with hand and foot function in different habitats; terrestrial species have straighter phalanges than their arboreal counterparts, and highly suspensory forms such as the orangutan possess the most curved phalanges. Sloth lemurs as a group are characterized by very curved proximal phalanges, exceeding those seen in spider monkeys and siamangs, and approaching that of orangutans. Indrids have curvatures roughly half that of sloth lemurs, and the more terrestrial, subfossil Archaeolemur possesses the least curved phalanges of all the indroids. Taken together with many other derived aspects of their postcranial anatomy, phalangeal curvature indicates that the sloth lemurs are one of the most suspensory clades of mammals ever to evolve.

NMR scalar couplings across Watson–Crick base pair hydrogen bonds in DNA observed by transverse relaxation-optimized spectroscopy

This paper describes the NMR observation of 15N—15N and 1H—15N scalar couplings across the hydrogen bonds in Watson–Crick base pairs in a DNA duplex, hJNN and hJHN. These couplings represent new parameters of interest for both structural studies of DNA and theoretical investigations into the nature of the hydrogen bonds. Two dimensional [15N,1H]-transverse relaxation-optimized spectroscopy (TROSY) with a 15N-labeled 14-mer DNA duplex was used to measure hJNN, which is in the range 6–7 Hz, and the two-dimensional hJNN-correlation-[15N,1H]-TROSY experiment was used to correlate the chemical shifts of pairs of hydrogen bond-related 15N spins and to observe, for the first time, hJHN scalar couplings, with values in the range 2–3.6 Hz. TROSY-based studies of scalar couplings across hydrogen bonds should be applicable for large molecular sizes, including protein-bound nucleic acids.

A influência do pensamento liberal de Benjamin Constant na formação do Estado Imperial Brasileiro / Cleber Francisco Alves. --

Inclui notas explicativas, bibliográficas e bibliografia.

The origins of stability of spontaneous vesicles

Equilibrium unilamellar vesicles are stabilized by one of two distinct mechanisms depending on the value of the bending constant. Helfrich undulations ensure that the interbilayer potential is always repulsive when the bending constant, K, is of order kBT. When K ≫ kBT, unilamellar vesicles are stabilized by the spontaneous curvature that picks out a particular vesicle radius; other radii are disfavored energetically. We present measurements of the bilayer elastic constant and the spontaneous curvature, Ro, for three different systems of equilibrium vesicles by an analysis of the vesicle size distribution determined by cryo-transmission electron microscopy and small-angle neutron scattering. For cetyltrimethylammonium bromide (CTAB)/sodium octyl sulfonate catanionic vesicles, K = .7 kBT, suggesting that the unilamellar vesicles are stabilized by Helfrich-undulation repulsions. However, for CTAB and sodium perfluorooctanoate (FC7) vesicles, K = 6 kBT, suggesting stabilization by the energetic costs of deviations from the spontaneous curvature. Adding electrolyte to the sodium perfluorooctanoate/CTAB vesicles leads to vesicles with two bilayers; the attractive interactions between the bilayers can overcome the cost of small deviations from the spontaneous curvature to form two-layer vesicles, but larger deviations to form three and more layer vesicles are prohibited. Vesicles with a discrete numbers of bilayers at equilibrium are possible only for bilayers with a large bending modulus coupled with a spontaneous curvature.