943 resultados para Conformação - Chapas metálicas


Relevância:

10.00% 10.00%

Publicador:

Resumo:

This work examines the possible effects of successive repair procedures on the microstructure of welded steel SAE 4130 by TIG welding process. Discussions and results were made about the metallographic analysis , non-metallic inclusions and microhardness tests , which were conducted on samples taken from the cradle engine component after the end of its life , a model airplane T-27 Tucano , made by EMBRAER and belonging were performed FAB . The choice of such component is due to the fact that this is critical to flight safety since it provides support for the aircraft engine . Thus regions of the weld metal , base metal and heat affected , with samples of the original weld bead , free of weld bead and also with four rework procedures for TIG welding zone were analyzed . It was found that after the fourth rework there is an increase in the amount of martensite , which may weaken the material with respect to resistance to fatigue. It was also found that the regions of the heat affected zone and weld metal have higher microhardness values when compared to those found in the base metal due to favoring the formation of ferritic and tempered martensite microstructures . Moreover, a welding process promotes a region with less non-metallic inclusions than metal base , which also explains the difference in the results obtained

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The research aimed to produce sheets of particles with waste processing of Eucalyptus sp bonded with urea-formaldehyde and evaluate the effect of pressure variation in the quality of the boards produced. To do so, the Boards made were divided into two treatments depending on the pressing pressure of 30 to 40 kgf / cm². Once pressings, climatized, the particleboards have been sectioned in test samples, and underwent physical-mechanical tests for determining density, swelling and water absorption, modulus of rupture and elasticity in static bending and internal linking. The particleboards pressed at 40 kgf / cm ² showed the best results

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This work has in its outline the analysis of the mechanical properties of the composition of plastic residues, denominated “plastic wood”, aiming at establishing technical parameters for application of this material in substitution to the natural wood. Plastic-Wood is basically, a combination of several kind of plastic, previously selected, washed, dried and without metallic particles, which are agglomerated, extruded or introduced into a mold. The manufacturer can choose different formats and colors. During this monograph it can be observed the use of several kind of plastic, their mechanical properties and the plastic-wood production process. Also are presented features and applications of natural wood, in order to better compare their uses in several applications

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Are being released in the construction market in Brazil ventures called Super 6. These businesses sell the promise of delivery of the apartment in six months after the launch of the venture. To meet this deadline are being deployed the constructive method of concrete walls using aluminum shapes. This system basically consists of pouring slabs and walls once, i.e. building up the wall shapes and slab joints. On the walls are used cloth, with reinforcements in vain and corners of walls and on these screens are tied the electrical boxes and conduits. For each tower is used the so-called system of half way, i.e. the system so it is sufficient to mount the Middle deck. Using a concrete which can be deformed in the next day you can lift one deck every two days with ready electric and hydraulicsystem, without having to tow the wall doing only minor fixes in the imperfections after concrete. With this system won an incredible speed in the construction of the structure reducing in almost one-third the length of the work. This work aims to compare in terms of cost-benefit of masonry structural systems and this new concrete wall system called Super 6. For this comparison will be used as parameter values used for the achievement of the Enterprise Portal of Roses of constructor Tenda which is one of the first to use concrete wall system. This project basically consists of seven towers of six floors each and will be budgeted the cost of this project if it were held in structural masonry. From these data it will be possible to make a comparison about the actual beneficial to adopt this system

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Fracture surfaces express sequences of events of energy release with crack propagation in metal alloys, the evolution of topographic features can indicate the lines of load action, failures during the use or processing. The quantitative fractography is an important tool in the study of fracture surfaces, because it allows their interpretation and characterization. In order to evaluate the effectiveness of the characterization of fracture surfaces grounded on concepts such as selfsimilarity and self-affinity, it used the 15-5PH steel that was characterized by metallographic and tensile tests. The metallography allows the microstructural characterization of this steel and proved the presence of the martensite phase in the slats form and a fine-grained, both in the radial and in the axial direction of the dowel. The tensile test (ASTM E8) of this material allowed the determination of the mechanical properties, so based on the obtained results it was possible to affirm that the 15-5PH steel has high mechanical properties and a good stretch. Besides, the specimens also underwent testing of crack propagation, standardized by ASTM E647-00, thus it was obtained the fracture surfaces for characterization under monofractal and multifractal approaches. In front of all the exposed it was possible to conclude that in all measurements the correlation between the crack tip position and the fractal dimension was established in accordance with changes in the thickness and in the fracture micromechanisms presents. Furthermore, the multifractal approach was more sensitive to these variations allowing a more detailed characterization of the morphology

Relevância:

10.00% 10.00%

Publicador:

Resumo:

O Estado do Acre, território mais recentemente incorporado ao Brasil, até meados do século XIX apresentava em seu território apenas povos tribais ameríndios, que lá habitavam desde milênios. O histórico de povoamento mais recente do estado (a partir da segunda metade do século XIX) está atrelado com o mercado internacional da borracha, a região foi o destino de milhares de pessoas em busca de fazer a vida explorando as seringueiras. A partir de então uma série de disputas fundiárias ocorreram na região, o que foi um dos fatores que influenciaram na conformação da sociedade acreana. O movimento ambientalista surgiu no estado como resultado dessas disputas fundiárias na segunda metade do século XX. No final da década 90 o governo estadual, assimilando o discurso ambientalista, assume o governo com a Frente Popular do Acre, composta por uma série de partidos, com o autodenominado “Governo da Floresta” e usando o neologismo “florestania” como símbolo do projeto do governo. Apesar de utilizar amplamente em seu discurso temáticas ambientais e dos povos da floresta, acabou ao longo dos anos tendo atitudes com um cunho mais doutrinador do que emancipador. A discrepância entre a prática e o discurso do “Governo da Floresta” é então analisada a partir de conceitos como “Ecologia dos Saberes” e “Biopoder”, conceitos que auxiliam na identificação das atitudes de cunho doutrinador postas em prática pelo governo. Considerando como “ecologia dos saberes” aquela forma de conhecimento que tem a premissa um reconhecimento da pluralidade de conhecimentos heterogêneos que em interações sustentáveis e dinâmicas entre eles não comprometem suas autonomias e “biopoder” como aquela forma de poder que exerce a sua dominação sobre a própria vida da população, estabelecendo como é que esses devem viver

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Radiotherapy is a branch of medical physics related to the treatment of malignant neoplasm, being an important instrument in the fight against cancer, when combined with the effort of a multidisciplinary team, composed of, physicians, physicists, nurses and technicians. Every year more than 3.5 million new cases of cancer are recorded in the world, being the prostate cancer responsible for approximately 25% of this amount (INCA and IARC, 2008). In this type of cancer, radiotherapy is a method indicated for treatement. The technological advance in this area over years has allowed a greater accuracy in the tumor location, more conformation of the radiation beam around the tumor, reducing the dose in healthy tissues and a consequent dose increase on treatment (Bedford et al., 1999). A radiotherapy planning, in which the physicist develops an important role, is composed of several steps, including choosing the best configuration of treatment beams. This choice has a close relationship with success of therapy and is critical to achieve the best distribution of dose inside the tumor and expose the least as possible the healthy tissue to radiation. In this work, two options for setting up camps in the first phase in a treatment of prostate cancer were simulated in computer planning: 4 fields orthogonal or “Box” with gantry angles in 00, 1800, 2700 e 90° and 4 fields angled or “X” (1350, 450, 3150 e 2250). The percentage of the rectal volume exposed to 40, 50, 60, 72 and 76 Gy should be limited to 60, 50, 25, 15 and 5% respectively (Greco et al., 2003). The femoral toxicity have limited dose by 70% of the total dose prescribed in a prostate treatment (Bedford et al., 1999). The planning of 27 patients with prostate adenocarcinoma submitted to 3D conformal radiotherapy were accompanied. As a result, it was assessed that the best TCP (tumor control probability)... (Complete abstract click electronic access below)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

With the market more and more disputed and negotiations where the customer is the main factor who decides whether the companies have conditions or not to dispute the market, industries must search improvements in products and processes targeting lower costs and better quality. With that in mind, this work will study the actual situation of a line of Tension Leveler, after cold mill process, for aluminum coil, and search new technologies, precisely the Scrap Baller machine, which will raise the quality level and the line’s productivity. It will be analyzed the justifications (reasons) for these new technologies, the history, the involved concepts, the operation, functions, the material that will be tension leveled, the limitations and tech and economic viability in comparison with the actual system. Also it will be taken a brief about the aluminum coil production in Brazil, especially the ones which destiny is aluminum beverage can, and the recycling process, that is very well done in Brazil, worldwide leader in aluminum recycling

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Hybrid composites combining metal plates and laminates with continuous fiber reinforced polymer, called fiber-metal (CHMF), have been particularly attractive for aerospace applications, due mainly to their high mechanical strength and stiffness associated with low density. These laminates (CHMF) consist of a sandwich structure consisting of layers of polymer composites and metal plates, stacked alternately. This setting allows you to combine the best mechanical performance of polymer composites reinforced with long fibers, to the high toughness of metals. Environmental effects should always be considered in the design of structural components, because these materials in applications are submitted to the effects of moisture in the atmosphere, the large cyclical variations of temperature around 82 ° C to -56 ° C, and high effort mechanical. The specimens of fibermetal composite were prepared at EMBRAER with titanium plates and laminates of carbon fiber/epoxy resin. This study aims to evaluate the effect of different environmental conditions (water immersion, hygrothermal chamber and thermal shock) of laminate hybrid titanium/carbon fiber/epoxy resin. The effects of conditioning were evaluated by interlaminar shear tests - ILSS, tensile, and vibration free

Relevância:

10.00% 10.00%

Publicador:

Resumo:

As enzimas estão presentes em todas as células vivas, onde exercem a função de catalisadores das reações que compõem as vias catabólicas e anabólicas do metabolismo celular. Esses biocatalisadores são moléculas de proteínas e seu poder catalítico está associado à conformação nativa, que depende de condições específicas de pH, temperatura e força iônica do meio. Os micro-organismos são bastante atrativos para a indústria, pois possibilitam a produção de enzimas por processos fermentativos em larga escala com regularidade necessária e simplicidade na requisição nutricional. Assim, embora alguns biocatalisadores sejam extraídos de tecidos animais e vegetais, as enzimas industriais são, em sua maior parte, obtidas a partir de micro-organismos. Este trabalho teve como objetivo a produção das enzimas lipase e β-glucanase a partir dos fungos Aspergillus niger e Trichoderma reesei, respectivamente, em diferentes meios de cultura, para determinar as condições de maior produção da enzima em questão. As enzimas produzidas em agitador orbital foram obtidas a partir da filtração do produto da fermentação, precipitação com sulfato de amônio e liofilização. Após a produção e precipitação a atividade das enzimas e a concentração de proteínas foram quantificadas, os parâmetros cinéticos foram determinados frente a diferentes pHs, temperaturas e força iônica do meio. A lipase apresentou melhor atividade a 30°C e em pH 6,0. A presença dos íons Mg2+ e Zn2+ levaram a um aumento na atividade da enzima. A β-glucanase apresentou maiores atividades quando submetidas a 37°C e pH 5,0. Os íons Mg2+, Cu2+ e Ca2+ induziram melhor a atividade enzimática.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The plastic deformation is widely used in the metallurgical market due to its positive factors such as low prices and high speed production. Forming process products are obtained in high quality, both surface quality and mechanical properties. Friction is an importante factor in metal forming. Friction study in metal forming can be accomplished indirectly, such as the ring test of friction. Two samples of different materials being mild steel and copper alloy were used. The results showed the influence of friction in the flow behavior of the deformation of the second phase, as evidenced by standard metallography. It is observed that in the outer regions of the ring, plastic deformation occured in the radial direction. In the central region of the disc deformation occured in the direction of compression and the inner region of the ring flux lines showed a significant deformation in the radial direction towards the center of the ring

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The society continues demonstrating its need regarding the products and services, even though it becomes increasingly value the protection of the environment. In this context, environmental management is defined as a management method that emphasizes to continuously improve results and promote sustainable development. Moreover it has as a tool the laws which provide the benchmarks and mechanisms for companies to adapt their activities in such a way that does not alter the quality of the environment. In this sense, in order to propose improvements to a dairy aiming their environmental suitability, a present study was prepared by following the production activities of the enterprise, the raising of standards and applicable legal requirements and environmental assessment for the preparation of an array of aspects and impacts with the task of identifying the most significant according to MOREIRA (2006). The results indicated that some of the impacts of high relevance are related to the generation of wastewater and solid waste, which do not have treatment and / or proper disposal and indeed require intervention for their suitability. Through, these results were drawn up proposals for actions conformation. In addition, they were proposed meeting the requirement for health and safety at work, in accordance with the standard regulations. This study has the function, therefore, propose to the company in question, an environmental management plan that ensures the protection of the environment and health of employees and consequently the improvement of production processes and products

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Decision making is one of the most important factors for growth and future, both from a business, as in people's life and attitudes in the simplest of everyday day. This work aims to assist decision making in buying a laser cut machine, a manufacturer of auto parts and wheels, and later this technique can be considered to acquisition of other equipment. In this case was used the AHP to aid the decision by multiple criteria. First we analyzed the most important criteria of the current machine for the application of the method and were later made the application and sensitivity analysis

Relevância:

10.00% 10.00%

Publicador:

Resumo:

O presente trabalho consiste em demonstrar valores referentes ao conforto ambiental de dois modelos construtivos, sendo o primeiro um edifício já executado e o outro em fase de implantação, ambos no Campus Experimental de Itapeva, aplicando alguns conceitos em habitação mais sustentáveis de madeira na região de Itapeva, estado de São Paulo, Brasil. A edificação construída sedia duas salas de aula a partir da tipologia construtiva wood frame, constituída basicamente de paredes autoportantes compostas de ossatura de madeira tratada de pinus.sp, chapas estruturais em OSB, manta de isolamento térmico/acústico e fechamento interno e externo, respectivamente em gesso e sidding (lambris de madeira). A habitação em fase de início de implantação foi idealizada a partir da tipologia construtiva log-home, e atenderá a necessidade de espaço físico para abrigar o Centro Acadêmico e a empresa-júnior “PROMAD”, ambos do curso de Engenharia Industrial Madeireira do Campus Experimental da UNESP/Itapeva. Esta construção foi elaborada a partir de técnicas de baixo impacto ambiental, levando em consideração os resultados de análise térmica obtidos na edificação anterior. Em ambos modelos construtivos foram empregados recursos renováveis abundantes na região, como a madeira de reflorestamento de Pinus e de Eucalipto. Foi acrescentado ainda ao segundo modelo a utilização de resíduos industriais lignocelulósicos, como rolete de laminação e outros materiais locais disponíveis. A metodologia básica empregada para a obtenção de dados sobre o conforto térmico em relação as edificações foi, para o primeiro caso, a coleta de dados de temperatura e umidade utilizando um termo-higrômetro, a sistematização e análise de dados reais obtidos no interior da edificação. No segundo caso, o dimensionamento do conforto térmico... (Resumo completo, clicar acesso eletrônico abaixo)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)