Controlled rippling of graphene via irradiation and applied strain modify its mechanical properties: a nanoindentation simulation study

Ripples, present in free standing graphene, have an important influence in the mechanical behavior of this two-dimensional material. In this work we show through nanoindentation simulations, how out-of-plane displacements can be modified by strain resulting in softening of the membrane under compression and stiffening under tension. Irradiation also induces changes in the mechanical properties of graphene. Interestingly, compressed samples, irradiated at low doses are stiffened by the irradiation while samples under tensile strain do not show significant changes in their mechanical properties. These simulations indicate that vacancies, produced by the energetic ions, cannot be the ones directly responsible for this behavior. However, changes in roughness induced by the momentum transferred from the energetic ions to the membrane, can explain these differences. These results provide an alternative explanation to recent experimental observations of stiffening of graphene under low dose irradiation, as well as paths to tailor the mechanical properties of this material via applied strain and irradiation.

Admittance Control for Robotic Loading: Design and Experiments with a 1-Tonne Loader and a 14-Tonne LHD

This paper describes the design, tuning, and extensive field testing of an admittance-based Autonomous Loading Controller (ALC) for robotic excavation. Several iterations of the ALC were tuned and tested in fragmented rock piles—similar to those found in operating mines—by using both a robotic 1-tonne capacity Kubota R520S diesel-hydraulic surface loader and a 14-tonne capacity Atlas Copco ST14 underground load-haul-dump (LHD) machine. On the R520S loader, the ALC increased payload by 18 % with greater consistency, although with more energy expended and longer dig times when compared with digging at maximum actuator velocity. On the ST14 LHD, the ALC took 61 % less time to load 39 % more payload when compared to a single manual operator. The manual operator made 28 dig attempts by using three different digging strategies, and had one failed dig. The tuned ALC made 26 dig attempts at 10 and 11 MN target force levels. All 10 11 MN digs succeeded while 6 of the 16 10 MN digs failed. The results presented in this paper suggest that the admittance-based ALC is more productive and consistent than manual operators, but that care should be taken when detecting entry into the muck pile

Development of a Mechanism and Process to Continuously Produce Spherical, Torrefied Biomass

Thesis (Master, Mechanical and Materials Engineering) -- Queen's University, 2016-06-17 02:15:25.215

Shoulder pain in overhead athletes : a systematic review of orthopaedic causes

Trabalho Final do Curso de Mestrado Integrado em Medicina, Faculdade de Medicina, Universidade de Lisboa, 2014

Total V9 rDNA information organized at the metabarcode level (Database W4)

The present data set provides a tab separated text file compressed in a zip archive. The file includes metadata for each TaraOceans V9 rDNA metabarcode including the following fields: md5sum = unique identifier; lineage = taxonomic path associated to the metabarcode; pid = % identity to the closest reference barcode from V9_PR2; sequence = nucleotide sequence of the metabarcode; refs = identity of the best hit reference sequence(s); TARA_xxx = number of occurrences of this barcode in each of the 334 samples; totab = total abundance of the barcode ; cid = identifier of the OTU to which the barcode belongs; and taxogroup = high-taxonomic level assignation of this barcode. The file also includes three categories of functional annotations: (1) Chloroplast: yes, presence of permanent chloroplast; no, absence of permanent chloroplast ; NA, undetermined. (2) Symbiont (small partner): parasite, the species is a parasite; commensal, the species is a commensal; mutualist, the species is a mutualist symbiont, most often a microalgal taxon involved in photosymbiosis; no the species is not involved in a symbiosis as small partner; NA, undetermined. (3) Symbiont (host): photo, the host species relies on a mutualistic microalgal photosymbiont to survive (obligatory photosymbiosis); photo_falc, same as photo, but facultative relationship; photo_klep, the host species maintains chloroplasts from microalgal prey(s) to survive; photo_klep_falc, same as photo_klep, but facultative; Nfix, the host species must interact with a mutualistic symbiont providing N2 fixation to survive; Nfix_falc, same as Nfix, but facultative; no, the species is not involved in any mutualistic symbioses; NA, undetermined. For example, the collodarian/Brandtodinium symbiosis is annotated: Chloroplast, "no"; Symbiont (small), "no"; Symbiont (host), "photo", for the collodarian host; and: Chloroplast, "yes"; Symbiont (small), "mutualist"; Symbiont (host), "no", for the dinoflagellate microalgal endosymbiont.chloroplast = "yes", "no" or "NA"; symbiont.small = "parasite", "commensal", "mutualist", "no" or "NA"; symbiont.host = "photo", "photo_falc", "photo_klep", "Nfix", no or NA; benef = "Nfix", "no" or "NA"; trophism = Metazoa , heterotroph , NA , photosymbiosis , phototroph according to the previous fields.

(Table 2) Physical properties at DSDP Holes 44-391 and 76-534

Laboratory measurements on sediment samples and density well logs run at DSDP Site 534 in the Blake-Bahama Basin were used to establish an in situ velocity and density structure. Synthetic seismograms were generated for comparison to reprocessed seismic reflection data in the vicinity of the Site. Uncertainties in the relative positions of the hole and seismic reflection data, velocity corrections, and the composition of the unrecovered section were evaluated. In light of the errors and compressed section, no unique correlation of the seismic reflection data to the drill hole is completely defensible either in this chapter or elsewhere. The preferred correlation resulting from this exercise is as follows, with the Site 534 report correlation shown in parentheses where different. Horizon beta', 887 m; Horizon beta, 950 m (975 m); Horizon C , 1202 m (1250 m); Horizon C, 1268 m (1340 m); Horizon D', 1342 m (1432 m); Horizon D, 1550 m (1552 m). The major differences in these correlations arise from the use of slightly different velocities and hole location relative to the seismic profiles. The Site 534 report results rely on hole placement on a basement flank, whereas in this chapter we locate it within a basement depression still within the uncertainty of the navigation. The Site 534 report also uses drilling rates, CDP velocity analyses, sonobuoy data, and previous similar drilling correlation methods used at Site 391, along with other geologic considerations in arriving at differing results. Although the correlation method used in this investigation is more objective and the hole location uncertainties better defined, in order to have confidence in any results we will require drilling in areas where reflections are either more widely spaced or where we have better vertical velocity control in the hole.

Isotopic geochemistry of lavas at DSDP Holes 81-553 and 81-555

It is demonstrated by K-Ar analyses that the age of reversely magnetized basalts, which immediately predate magnetic Anomaly 24B, is 53.5 ± 1.9 m.y. Samples from deep levels appear to be grossly contaminated by an extraneous argon component with a uniform argon-40/argon-36 ratio 440. This component is thought to have been derived from fluids circulating in the lava pile during burial. The age result corroborates the assignment previously made to Anomaly 24B by Hailwood et al. (1979) and Lowrie and Alvarez (1981). It additionally suggests that lava extrusion formed part of a much larger magmatic event, which affected wide areas of the North Atlantic margins around the Paleocene/Eocene boundary, and can therefore probably be considered a good estimate of the age of this boundary. Initial 143Nd/144Nd ratios lie in the very restricted range 0.512920 ± 19 to 0.513026 ± 24 and initial 8 7Sr/86Sr ratios from ca. 0.703 to ca. 0.705. Acid leaching reduces the latter range to 0.70264 ± 4 to 0.70384 ± 4, suggesting that the higher 87Sr/86Sr ratios resulted from interaction with seawater. The array of data for treated samples is closely conformable on a 143Nd/144Nd-87Sr/86Sr diagram with the main oceanic mantle array and with previously published fields for Atlantic Ocean basalts. No evidence for any continental crustal contamination has been found. This suggests, but does not prove, that continental crust played no part in the genesis of these rocks.

Database of GPS data collected by surveys on seismic and volcanic areas of Sicily (Italy) from 1994 to 2013

This is a 20-year long database of GPS data collected by geodetic surveys carried out over the seismically and volcanically active eastern Sicily, for a total of more than 6300 measurements. Data have been convertedi nto the international ASCII compressed RINEX standard in order to be imported and processed by any GPS analysis software. Database is provided with an explorer software for navigating into the dataset by spatial (GIS) and temporal queries.

Chemical composition of rhyolites of ODP Site 103-639

Holes 639E and 639F were drilled along the western slope of a tilted fault block in an attempt to recover complete syn- and pre-rift stratigraphic sections and continental basement. Both holes ended in an apparent talus pile or conglomerate that includes cobbles of altered rhyolitic rock. Three small pieces of rhyolite (comprising about 20 cm of sample) were recovered from the bottoms of Holes 639E and 639F in the core catchers of the deepest cores. This note presents geochemical data from these rhyolitic rocks. Also recovered were quartz sandstones, graywackes, metasandstones, and quartz breccias. This assemblage of continentally derived 'basement' material was overlain by mudstones, limestones, and crystalline dolomites (see 'Site 639' chapter; Shipboard Scientific Party, 1987, doi:10.2973/odp.proc.ir.103.110.1987).

(Fig. 9) Pollen analysis of sediment core GIK16017-2

The improved understanding of the pollen signal in the marine sediments offshore of northwest Africa is applied to deep-sea core M 16017-2 at 21°N. Downcore fluctuations in the percentage, concentration and influx diagrams record latitudinal shifts of the main northwest African vegetation zones and characteristics of the trade winds and the African Easterly Jet. Time control is provided by 14C ages and 180 records. During the period 19,000-14,000 yr B.P. a compressed savanna belt extended between about 12 ° and 14-15°N. The Sahara had maximally expanded northward and southward under hyperarid climatic conditions. The belt with trade winds and dominant African Easterly Jet transport had not shifted latitudinally. The trade winds were strong as compared to the modern situation but around 13,000 yr B.P. the trade winds weakened. After 14,000 yr B.P. the climate became less arid south of the Sahara and a first spike of fluvial runoff is registered around 13,000 yr B.P. Fluvial runoff increased strongly around 11,000 yr B.P. and maximum runoff is recorded from about 9000-7800 yr B.P. Around 12,500 yr B.P. the savanna belt started to shift northward and became richer in woody species: it shifted about 6° of latitude, reached its northernmost position during the period of 9200-7800 yr B.P. and extended between about 16° and 24°N at that time. Tropical forest had reached its maximum expansion and the Guinea zone reached as far north as about 15°N, reflecting very humid climatic conditions south of the Sahara. North of the Sahara the climate also became more humid and Mediterranean vegetation developed rapidly. The Sahara had maximally contracted and the trade winds were weak and comparable with the present day intensity. After about 7800 yr B.P. the southern fringe of the Sahara and accordingly the savanna belt, shifted rapidly southward again.

(Table 1) Results from XRD analysis as well as sediment type and selected results from ring shear experiments

The location of the seaward tip of a subduction thrust controls material transfer at convergent plate margins, and hence global mass balances. At approximately half of those margins, the material of the subducting plate is completely underthrust so that no accretion or even subduction erosion takes place. Along the remaining margins, material is scraped off the subducting plate and added to the upper plate by frontal accretion. We here examine the physical properties of subducting sediments off Costa Rica and Nankai, type examples for an erosional and an accretionary margin, to investigate which parameters control the level where the frontal thrust cuts into the incoming sediment pile. A series of rotary-shear experiments to measure the frictional strength of the various lithologies entering the two subduction zones were carried out. Results include the following findings: (1) At Costa Rica, clay-rich strata at the top of the incoming succession have the lowest strength (µres = 0.19) while underlying calcareous ooze, chalk and diatomite are strong (up to µres = 0.43; µpeak = 0.56). Hence the entire sediment package is underthrust. (2) Off Japan, clay-rich deposits within the lower Shikoku Basin inventory are weakest (µres = 0.13-0.19) and favour the frontal proto-thrust to migrate into one particular horizon between sandy, competent turbidites below and ash-bearing mud above. (3) Taking in situ data and earlier geotechnical testing into account, it is suggested that mineralogical composition rather than pore-pressure defines the position of the frontal thrust, which locates in the weakest, clay mineral-rich (up to 85 wt.%) materials. (4) Smectite, the dominant clay mineral phase at either margin, shows rate strengthening and stable sliding in the frontal 50 km of the subduction thrust (0.0001-0.1 mm/s, 0.5-25 MPa effective normal stress). (5) Progressive illitization of smectite cannot explain seismogenesis, because illite-rich samples also show velocity strengthening at the conditions tested.

Early Cretaceous planktonic foraminifera from the Tethys

Early Cretaceous planktonic foraminiferal assemblages include rare planispiral and pseudoplanispiral morphotypes with elongate chambers that BouDagher-Fadel et al. assigned to Schackoina or accommodated in the new genus Claviblowiella. New findings of well-preserved planktonic foraminiferal faunas from the Lesches en Diois (SE France) section, the Cismon core (NE Italy), the Calabianca (NW Sicily) section and the Upper Aptian of Deep Sea Drilling Project (DSDP) Site 545 drilled off Morocco, have allowed a better understanding of the morphological features of these rare, unevenly distributed taxa. Our data demonstrate that each small planispiral species with globular chambers has a corresponding "clavate" morphotype which (as the "normal" forms) exhibits a smooth, finely perforate wall. Consequently, the latter have been assigned here to the genus Globigerinelloides and treated as subspecies of the "non-clavate" taxa. The (clavate) subspecies belonging to the genus Globigerinelloides here retained are G. duboisi sigali Longoria, G. maridalensis elongatus subsp. nov., G. blowi lobatus subsp. nov. and G. paragottisi clavatus subsp. nov., while Globigerinelloides minai Obregòn de la Parra is not retained. In addition, a new genus, Pseudoschackoina, type species Planomalina saundersi Bolli (senior synonym of Hastigerinoides cepedai Obregòn de la Parra, has been formalised for individuals possessing elongate, pointed, laterally compressed chambers, bearing tubulospines arranged on a pseudoplanispiral (dysaxial) coiling mode. Stratigraphically, in the sections studied the first taxon to appear is Pseudoschackoina saundersi, in the uppermost part of the Selli Level (=OAE1a), immediately followed, just above the OAE1a, by all the "clavate" globigerinelloidids. Regarding the last occurrences, Pseudoschackoina saundersi and G. maridalensis elongatus disappear in the lower part of the Globigerinelloides algerianus Zone, Globigerinelloides paragottisi clavatus at the top of the same zone, while Globigerinelloides blowi lobatus and G. duboisi sigali range up to the lower part of the Ticinella bejaouaensis Zone.

Concentrations and isotopic compositions of low molecular weight hydrocarbons in hydrothermal fluids from ODP Field, Middle Valley, northern Juan de Fuca Ridge

The presence of sedimentary organic matter blanketing midocean ridge crests has a potentially strong impact on metal transport in hydrothermal vent fluids. To constrain the role of organic matter in metal mobility during hydrothermal sediment alteration, we reacted organic-rich diatomaceous ooze from Guaymas Basin, Gulf of California, and organic-poor hemipelagic mud from Middle Valley, northern Juan de Fuca Ridge, with seawater and a Na-Ca-K-Cl fluid of seawater chlorinity, at 275° to 400°C, 350 to 500 bars, and initial fluid: sediment mass ratios ranging from 1.6 to 9.8. Reaction of these fluids with both sediment types released CO2 and high concentrations of ore-forming metals (Fe, Mn, Zn, Pb) to solution. Relatively low concentrations of Cu were observed in solution and likely reflect the reducing conditions that resulted from the presence of sedimentary organic matter. Both the concentrations of CO2 and dissolved metals were lower in fluids reacted with Middle Valley sediment compared with aqueous concentrations in fluids reacted with Guaymas Basin sediment. During alteration of both sediment types, metal concentrations varied strongly as a function of temperature, increasing by up to an order of magnitude over the 75°C range of each experiment. Major element fluid chemistry and observed alteration assemblages suggest that during hydrothermal alteration of organic-lean sediment from Middle Valley a feldspar-quartz-illite mineral assemblage buffered in situ pH. In contrast, data from the experimental alteration of organic-rich Guaymas Basin sediment suggest that a calcite-plagioclase-quartz assemblage regulated in situ pH. Fluid speciation calculations suggest that in situ pH during Guaymas Basin sediment alteration was lower than during alteration of Middle Valley sediment and accounts for the substantially greater metal mobility at a given temperature and pressure during the former experiment. Comparison of our results with the results of basalt alteration experiments indicate that except for Cu, hydrothermal sediment alteration results in equal or greater concentrations of ore-forming metals at a given temperature and pressure. Accordingly, the presence of ore-forming metals in fluids currently venting from sediment-covered hydrothermal systems at concentrations substantially lower than in fluids from bare-rock systems may reflect chemical reequilibration during subsurface cooling within the sediment pile.

Final report of a 1991 Plymouth Acclaim rear impact CNG fuel tank integrity.

National Highway Traffic Safety Administration, Washington, D.C.