Real time fault injection using enhanced OCD -- a performance analysis

Fault injection is frequently used for the verification and validation of dependable systems. When targeting real time microprocessor based systems the process becomes significantly more complex. This paper proposes two complementary solutions to improve real time fault injection campaign execution, both in terms of performance and capabilities. The methodology is based on the use of the on-chip debug mechanisms present in modern electronic devices. The main objective is the injection of faults in microprocessor memory elements with minimum delay and intrusiveness. Different configurations were implemented and compared in terms of performance gain and logic overhead.

The effect of superplasticizers on the mechanical performance of concrete made with fine recycled concrete aggregates

It is considered that using crushed recycled concrete as aggregate for concrete production is a viable alternative to dumping and would help to conserve abiotic resources. This use has fundamentally been based on the coarse fraction because the fine fraction is likely to degrade the performance of the resulting concrete. This paper presents results from a research work undertaken at Institut Superior Tecnico (IST), Lisbon, Portugal, in which the effects of incorporating two types of superplasticizer on the mechanical performance of concrete containing fine recycled aggregate were evaluated. The purpose was to see if the addition of superplasticizer would offset the detrimental effects associated with the use of fine recycled concrete aggregate. The experimental programme is described and the results of tests for splitting tensile strength, modulus of elasticity and abrasion resistance are presented. The relative performance of concrete made with recycled aggregate was found to decrease. However, the same concrete with admixtures in general exhibited a better mechanical performance than the reference mixes without admixtures or with a less active superplasticizer. Therefore, it is argued that the mechanical performance of concrete made with fine recycled concrete aggregates can be as good as that of conventional concrete, if superplasticizers are used to reduce the water-cement ratio of the former concrete.

Anti-Corrosion performance of a new silane coating for corrosion protection of AZ31 Magnesium alloy in Hank’s solution

Mg alloys can be used as bioresorsable metallic implants. However, the high corrosion rate of magnesium alloys has limited their biomedical applications. Although Mg ions are essential to the human body, an excess may cause undesirable health effects. Therefore, surface treatments are required to enhance the corrosion resistance of magnesium parts, decreasing its rate to biocompatible levels and allowing its safe application as bioresorbable metallic implants. The application of biocompatible silane coatings is envisaged as a suitable strategy for retarding the corrosion process of magnesium alloys. In the current work, a new glycidoxypropyltrimethoxysilane (GPTMS) based coating was tested on AZ31 magnesium substrates subjected to different surface conditioning procedures before coating deposition. The surface conditioning included a short etching with hydrofluoric acid (HF) or a dc polarisation in alkaline electrolyte. The silane coated samples were immersed in Hank's solution and the protective performance of the coating was studied through electrochemical impedance spectroscopy (EIS). The EIS data was treated by new equivalent circuit models and the results revealed that the surface conditioning process plays a key role in the effectiveness of the silane coating. The HF treated samples led to the highest impedance values and delayed the coating degradation, compared to the mechanically polished samples or to those submitted to dc polarisation.

Characterization and performance analysis of a VDFLL GNSS receiver architecture

A non-coherent vector delay/frequency-locked loop architecture for GNSS receivers is proposed. Two dynamics models are considered: PV (position and velocity) and PVA (position, velocity, and acceleration). In contrast with other vector architectures, the proposed approach does not require the estimation of signals amplitudes. Only coarse estimates of the carrier-to-noise ratios are necessary.

Impact of different moodle course designs on students? Performance

This work describes the impact of different teachers’ approaches in using Moodle, for supporting their courses, at the Polytechnic of Porto - School of Engineering. The study covers five different courses, from different degrees and different years, and includes a number of Moodle resources especially supporting laboratory classes. These and other active resources are particularly analyzed in order to evaluate students’ adherence to them. One particular course includes a number of remote experiments, made available through VISIR (Virtual Instrument Systems in Reality) and directly accessible through links included in the Moodle course page. The collected data have been correlated with students’ classifications in the lab component and in the exam, each one weighting 50% of their final marks. This analysis benefited from the existence of different teachers’ approaches, which resulted in a diversity of Moodle-supported environments. Conclusions point to the existence of a positive correlation factor between the number of Moodle accesses and the final exam grade, although the quality of the resources made available by the teachers seems to be preponderant over its quantity. In addition, different students perspectives were found regarding active resources: while some seem to encourage students to participate (for instance online quiz or online reports), others, more demanding, are unable to stimulate the majority of them.

Student performance analysis under different moodle course designs

This work extends a recent comparative study covering four different courses lectured at the Polytechnic of Porto - School of Engineering, in respect to the usage of a particular Learning Management System, i.e. Moodle, and its impact on students' results. A fifth course, which includes a number of resources especially supporting laboratory classes, is now added to the analysis. This particular course includes a number of remote experiments, made available through VISIR (Virtual Instrument Systems in Reality) and directly accessible through links included in the Moodle course page. We have analyzed the students' behavior in following these links and in effectively running experiments in VISIR (and also using other lab related resources, in Moodle). This data have been correlated with students' classifications in the lab component and in the exam, each one weighting 50% of their final marks. We aimed to compare students' performance in a richly Moodle-supported environment (with lab component) and in a poorly Moodle-supported environment (with only theoretical component). This question followed from conclusions drawn in the above referred comparative study, where it was shown that even though a positive correlation factor existed between the number of Moodle accesses and the final exam grade obtained by each student, its explanation behind was not straightforward, as the quality of the resources was preponderant over its quantity.

Factores que influenciam a mortalidade de abetarda e sisão por colisão em linhas de muito alta tensão. Análises às escalas local e regional e implicações para o Ordenamento do Território

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Ordenamento do Território e Planeamento Ambiental

Determinação do teor de compostos aromáticos policíclicos de óleos minerais isolantes para transformadores

Mestrado em Engenharia Química - Ramo Optimização Energética na Indústria Química

Sistema didáctico de baixo custo com FPGA de alta densidade

O uso das Field-Programmable Gate Array tem crescido de forma exponencial. Com isto dito, é importante que os engenheiros electrotécnicos estejam familiarizados com este tipo de tecnologia. Foi com o intuído de passar estas valências para os alunos do ISEP, que surgiu a ideia de criar um sistema didáctico, que permitisse ao alunos aprender a trabalhar com estes dispositivos. O seguinte trabalho iniciou-se com base num estudo das características destes dispositivos e das suas potencialidades, seguido de uma avaliação do que o mercado tem para oferecer. Posteriormente, com base em toda a informação reunida, foi definida a arquitectura do sistema, que levou selecção de dispositivos a incluir no mesmo, e culminando na concepção do esquema eléctrico do sistema e da placa de circuito impresso correspondente ao protótipo do mesmo. As principais directivas para este projecto foram o uso de uma FPGA de alta densidade e a concepção da ferramenta com o custo de projecto o mais reduzido possível.

Suporte à computação paralela e distribuída em Java: distribuição e execução de trabalho

Nos últimos anos começaram a ser vulgares os computadores dotados de multiprocessadores e multi-cores. De modo a aproveitar eficientemente as novas características desse hardware começaram a surgir ferramentas para facilitar o desenvolvimento de software paralelo, através de linguagens e frameworks, adaptadas a diferentes linguagens. Com a grande difusão de redes de alta velocidade, tal como Gigabit Ethernet e a última geração de redes Wi-Fi, abre-se a oportunidade de, além de paralelizar o processamento entre processadores e cores, poder em simultâneo paralelizá-lo entre máquinas diferentes. Ao modelo que permite paralelizar processamento localmente e em simultâneo distribuí-lo para máquinas que também têm capacidade de o paralelizar, chamou-se “modelo paralelo distribuído”. Nesta dissertação foram analisadas técnicas e ferramentas utilizadas para fazer programação paralela e o trabalho que está feito dentro da área de programação paralela e distribuída. Tendo estes dois factores em consideração foi proposta uma framework que tenta aplicar a simplicidade da programação paralela ao conceito paralelo distribuído. A proposta baseia-se na disponibilização de uma framework em Java com uma interface de programação simples, de fácil aprendizagem e legibilidade que, de forma transparente, é capaz de paralelizar e distribuir o processamento. Apesar de simples, existiu um esforço para a tornar configurável de forma a adaptar-se ao máximo de situações possível. Nesta dissertação serão exploradas especialmente as questões relativas à execução e distribuição de trabalho, e a forma como o código é enviado de forma automática pela rede, para outros nós cooperantes, evitando assim a instalação manual das aplicações em todos os nós da rede. Para confirmar a validade deste conceito e das ideias defendidas nesta dissertação foi implementada esta framework à qual se chamou DPF4j (Distributed Parallel Framework for JAVA) e foram feitos testes e retiradas métricas para verificar a existência de ganhos de performance em relação às soluções já existentes.

Marx-Type solid-state bipolar modulator topologies: Performance comparison

The operation of generalized Marx-type solid-state bipolar modulators is discussed and compared with simplified Marx-derived circuits, to evaluate their capability to deal with various load conditions. A comparative analysis on the number of switches per cell, fiber optic trigger count, losses, and switch hold-off voltages has been made. A circuit topology is obtained as a compromise in terms of operating performance, trigger simplicity, and switching losses. A five-stage laboratory prototype of this circuit has been assembled using 1200 V insulated gate bipolar transistors (IGBTs) and diodes, operating with 1000 V dc input voltage and 1 kHz frequency, giving 5 kV bipolar pulses, with 2.5 mu s pulse width and 5 mu s relaxation time into resistive, capacitive, and inductive loads.

Melhoria de protocolos de encaminhamento em VANETs de alta densidade

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores

High-performance flexible hybrid field-effect transistors based on cellulose fiber paper

IEEE Electron Device Letters, VOL. 29, NO. 9,

Performance of fractional PID algorithms controlling nonlinear systems with saturation and backlash phenomena

The development of fractional-order controllers is currently one of the most promising fields of research. However, most of the work in this area addresses the case of linear systems. This paper reports on the analysis of fractional-order control of nonlinear systems. The performance of discrete fractional-order PID controllers in the presence of several nonlinearities is discussed. Some results are provided that indicate the superior robustness of such algorithms.

The impact of national cultures on international marketing strategy and subsidiary performance of portuguese SME’s

The dynamic of the international business and its multidimensional nature requires the understanding of the complexities of different contexts dictated by cultural differences between countries. The purpose of this paper is to study, in depth howsmall and medium-sized companies develop their international marketing mix strategy in their overseas subsidiaries. We use the theoretical construct of Hofstede (1980, 1991) in the dimensions of Power Distance (PD), Uncertainty Avoidance (UA), Individualism (IND), Masculinity (MASC) and Long-Term Orientation (LTO) to assess the cross cultural differences between countries and the business practices to analyze the adaptation or standardization of the international marketing mix strategy of foreign Portuguese subsidiaries. Ourstudy uses an exploratoryand qualitative methodology. We conducted semi-structured interviews in order to achieve a good understanding ofinternational marketing mix strategy of four companies from different sectors. Our results show that the national cultural differences have great influence in the marketing strategy of the subsidiary. The business practices adjustments in the subsidiary company that proved to be necessary conditions for their performance are conducted by the products augmented offerings concerning the characteristics of the product, design and brand name in order to meet the requirements and specificities of the host country of the subsidiary.