Atenolol characterization in solid formulations available in Brazilian market

Atenolol is the most used drug in Brazil to hypertension treatment. Two crystal structures are known for this molecule: a racemic form (R,S)-atenolol and a pure form S-atenolol. The racemic form is found in commercial tablets. X-ray powder diffraction (XRD) is an adequate tool to study crystalline structures including drugs. Using the Rietveld Method with XRD data it is possible to quantify the crystalline structures existing in the raw material. Other methods like Le Bail and Pawley can be used to the profile fit and phases identification. For this work we analyzed three tablets of atenolol, two generics and the reference (materials were purchased from a drugstore at the city of Araraquara). These tablets were analyzed by Rietveld, Le Bail and Pawley methods. All tablets exhibited the racemic mixture API (R,S)-atenolol. Some crystalline excipients could be characterized: magnesium carbonate hydrate, lactose monohydrate and talc. The conclusion is that the three methods can be efficiently used to characterize the three atenolol tablets.

Chemical characterization and bioactivity of epoxy resin and Portland cement-based sealers with niobium and zirconium oxide radiopacifiers

The purpose of this study was to characterize and to evaluate the bioactivity potential of experimental root canal sealers (ES) based on Portland cement, epoxy resin with nano- and micro-particles of niobium or zirconium oxide used as radiopacifiers in comparison to AH Plus and MTA Fillapex. Methods Specimens of the sealers (10 mm in diameter × 1 mm thick) were prepared and the radiopacity was evaluated according to ISO 6876 (2012) specifications. Characterization of the sealers was performed under the scanning electron microscope (SEM) immediately after setting and after immersion for 28 days in Hank's balanced salt solution (HBSS). In addition X-ray energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) spectroscopy were also performed. The pH and calcium ion release were measured after 1, 7, 14, 21 and 28 days after completion of seating using a digital pH meter and an atomic absorption spectrophotometer, respectively. Results The experimental sealers exhibited an average radiopacity of 2.5 mm thickness of aluminum, which was similar to MTA Fillapex (P > 0.05) and inferior to AH Plus (P < 0.05). AH Plus did not show bioactivity. Although the experimental sealers did not exhibit the formation of hydration product, they encouraged the deposition of crystalline spherical structures of calcium deficient phosphate. The highest pH and calcium release values were observed with the experimental sealers (P < 0.01). ES-Nb-micro was the only sealer to present hexagonal shaped crystal deposition. Significance Novel root canal sealers based on a mixture of Portland cement, epoxy resin and radiopacifier exhibited a degree of bioactivity although no evidence of cement hydration was demonstrated on material characterization. The radiopacifier particle size had limited effect on the sealer microstructure and chemical properties.

Molecular characterization of intestinal protozoa in two poor communities in the State of São Paulo, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Advanced Molecular Surveillance of Hepatitis C Virus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Expression, purification and characterization of cold shock protein A of Corynebacterium pseudotuberculosis

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Polyacrylic acid polymers hydrogels intended to topical drug delivery: preparation and characterization

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Neural tool condition estimation in the grinding of advanced ceramics

Ceramic parts are increasingly replacing metal parts due to their excellent physical, chemical and mechanical properties, however they also make them difficult to manufacture by traditional machining methods. The developments carried out in this work are used to estimate tool wear during the grinding of advanced ceramics. The learning process was fed with data collected from a surface grinding machine with tangential diamond wheel and alumina ceramic test specimens, in three cutting configurations: with depths of cut of 120 mu m, 70 mu m and 20 mu m. The grinding wheel speed was 35m/s and the table speed 2.3m/s. Four neural models were evaluated, namely: Multilayer Perceptron, Radial Basis Function, Generalized Regression Neural Networks and the Adaptive Neuro-Fuzzy Inference System. The models'performance evaluation routines were executed automatically, testing all the possible combinations of inputs, number of neurons, number of layers, and spreading. The computational results reveal that the neural models were highly successful in estimating tool wear, since the errors were lower than 4%.

Colleters on the inflorescence axis of croton glandulosus (euphorbiaceae): structural and functional characterization

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Surface characterization of lithium disilicate ceramic after nonthermal plasma treatment

Statement of problem. Surface transformation with nonthermal plasma may be a suitable treatment for dental ceramics, because it does not affect the physical properties of the ceramic material.Purpose. The purpose of this study was to characterize the chemical composition of lithium disilicate ceramic and evaluate the surface of this material after nonthermal plasma treatment.Material and methods. A total of 21 specimens of lithium disilicate (10 mm in diameter and 3 mm thick) were fabricated and randomly divided into 3 groups (n=7) according to surface treatment. The control group was not subjected to any treatment except surface polishing with abrasive paper. In the hydrofluoric acid group, the specimens were subjected to hydrofluoric acid gel before silane application. Specimens in the nonthermal plasma group were subjected to the nonthermal plasma treatment. The contact angle was measured to calculate surface energy. In addition, superficial roughness was measured and was examined with scanning electron microscopy, and the chemical composition was characterized with energy-dispersive spectroscopy analysis. The results were analyzed with ANOVA and the Tukey honestly significant difference test (alpha=.05).Results. The water contact angle was decreased to 0 degrees after nonthermal plasma treatment. No significant difference in surface roughness was observed between the control and nonthermal plasma groups. Scanning electron microscopy and energy-dispersive spectroscopy images indicated higher amounts of oxygen (O) and silicon (Si) and a considerable reduction in carbon (C) in the specimens after nonthermal plasma treatment.Conclusions. Nonthermal plasma treatment can transform the characteristics of a ceramic surface without affecting its surface roughness. A reduction in C levels and an increase in 0 and Si levels were observed with the energy-dispersive spectroscopy analysis, indicating that the deposition of the thin silica film was efficient.

Characterization of grazing bifurcation in airfoils with control surface freeplay nonlinearity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural characterization of Li-MN doped powders prepared by Pechini's method

Pechini's method has been successfully used to prepare Li-doped MgNb2O6(MN) at short time and low temperature. It consists in the preparation of metal citrate solution, which is polymerized at 250°C to form a high viscous resin. This resin was burned in a box type furnace at 400°C/2h and ground in a mortar. Successive steps of calcination up to 900°C were used to form a crystalline precursor. SEM, DTA and XRD were used to characterize the powders. MN precursor powders containing from 0.1 to 5.0 mol% of LiNbO3 additive was prepared aiming better dielectric properties and microstructural characteristics of the PMN prepared from columbite route. SEM analysis showed that particles increased by sintering, forming large agglomerates. The surface area is also substantially reduced with the increase in additive amount above 1.0 mol%. In XRD pattern of the precursor material with 5.0 mol% of additive was observed the LiNbO3 phase of trigonal structure. XRD data were used for Rietveld refinement and a decrease in microstrain and pronounced increase in crystallite size with the increase of LiNbO3 were observed. It is in agreement with the particle morphologies observed by SEM analysis.

Comparison of imaging methods for diagnosis of renal tumors and their calcifications

Background: To establish the best methodology for diagnosis and management of patients with solid and complex renal masses by comparing the costs and benefits of different imaging methods and to improve differential diagnosis of these benign and malignant lesions, particularly by investigating tumour calcifications. Methods: We performed a prospective study on 31 patients with solid or complex masses by submitting them to Abdominal Ultrasonography (US), Doppler Ultrasonography of the renal mass (US Dop), Computed Tomography (CT), and Magnetic Resonance Imaging (MRI). Results: We found 28 patients with malignant and three with benign masses. Of the 28 malignant, 17 showed calcifications at CT; 16 central and one was of the pure peripheral curvilinear type (egg shell). Excretory Urography (IVP) had a significantly lower detection rate for central calcifications than both US and CT. Benign and malignant masses appeared as described in literature, with US, CT and MRI showing high sensitivity and specificity in renal tumor diagnosis. The exception was US Dop where we obtained lower sensitivity for the characterization of malignant tumor flow. Conclusions: In this series we were surprised to find that CT revealed central calcifications in 51.6% of patients, all with malignant lesions, while, literature reports a frequency of calcification in renal cell carcinoma between 8 and 22%, in studies using abdominal films and EU (IVP). This finding is of great importance when we consider that these calcifications occur particularly in malignant neoplasms. As a result of comparing these different imaging methods we have developed a better methodology for renal tumor investigation.

Malnutrition in patients with gastrointestinal cancer: effectiveness of different diagnostic methods

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Diagnóstico ambiental em área com vazamento de combustíveis por meio da integração de dados geofísicos e geoquímicos no município de São Manuel - SP

The contamination of the physical environment occurs as a result of the lack of planning and inadequate management of hazardous products. Due to the difficulty of the characterization and study of soil and groundwater, the contamination has been long neglected. The characterization of these areas by research techniques through direct methods such as physical and chemical analysis, are widely used in the diagnosis and monitoring. However, despite presenting quantitative results, this method is not representative in spatial terms. The purpose of this work is to bring geophysical complementation with the diagnosis, bringing the spatial element for the detection of the contamination plume. In the study area, there was a railway accident in 1999 in which three wagons fell and spilled 240,000 L of diesel onto the soil. The main objective is to assess the presence of contaminants in the residual phase and dissolved in the subsurface, using the technique of Electrical Tomography (ETR), understand the effects of natural attenuation process in the degradation of hydrocarbons and changes in electrical properties in soil and groundwater. The results allowed the definition of three distinct patterns of resistivity region with presence of dissolved phase, set in a historical chemical analyzes: low values (> 60Ω.m) associated with the presence of hydrocarbons in an advanced stage of degradation, intermediate values (260Ω.me 511Ω .m) indicative of coexistence of residual hydrocarbons and dissolved phase, and high values (> 1000Ω.m), which reveal the prevalence of residual phase with incipient degradation, possibly in high toxicity concentrations for effective action of biodegradation processes. The diagnostic of areas with potential accumulation of residual phase can subsidize the planning of remediation techniques and promote the complete decontamination of the area

Physico-chemical characterization and analytical development for sodium azumolene, a potential drug designed to fight malignant hyperthermia

Sodium azumolene is a drug designed to fight Malignant Hyperthermia (MH), which is characterized by genetic predisposition and triggered by the use of inhalational anesthetics. This drug is shown as a water-soluble analogue of dantrolene sodium, 30-folds more water soluble, which gives advantages for its emergency use. To our knowledge there is no analytical method for sodium zaumolene raw material or dosage form published so far. The objective of the present investigation was to develop and validate analytical methods to achieve sodium azumolene chemical identification and quantification. The sodium azumolene was characterized regarding its thermal behavior, by differential thermal analysis and thermogravimetric analysis; Visible, UV and infrared absorption. To accurately assess the sodium Azumolene content three different analytical methods (visible and UV spectrophotometry and high performance liquid chromatography) were developed and validated. All methods showed to be linear, accurate, precise and reliable. Azumolene has shown to be equipotent to dantrolene in the treatment and prevention of an MH crisis and the great advantage compared to dantrolene is better water solubility. This study has characterized the sodium azumolene and presents new analytical methods which have not been reported so far.