Precise determination of anomalous scattering factors of Ge by using X-ray resonant scattering

Variations of peak position of the rocking curve in the Bragg case are measured from a Ge thin crystal near the K-absorption edge. The variations are caused by a phase change of the real part of the atomic scattering factor. Based on the measurement, the values of the real part are determined with an accuracy of better than 1%. The values are the most reliable ones among those reported values so far as they are directly determined from the normal atomic scattering factors.

Variation in trawl geometry due to unequal warp length

Survey standardization procedures can reduce the variability in trawl catch efficiency thus producing more precise estimates of biomass. One such procedure, towing with equal amounts of trawl warp on both sides of the net, was experimentally investigated for its importance in determining optimal trawl geometry and for evaluating the effectiveness of the recent National Oceanic and Atmospheric Administration (NOAA) national protocol on accurate measurement of trawl warps. This recent standard for measuring warp length requires that the difference between warp lengths can be no more than 4% of the distance between the otter doors measured along the bridles and footrope. Trawl performance data from repetitive towing with warp differentials of 0, 3, 5, 7, 9, 11, and 20 m were analyzed for their effect on three determinants of flatfish catch efficiency: footrope distance off-bottom, bridle length in contact with the bottom, and area swept by the net. Our results indicated that the distortion of the trawl caused by asymmetry in trawl warp length could have a negative inf luence on flatfish catch efficiency. At a difference of 7 m in warp length, the NOAA 4% threshold value for the 83112 Eastern survey trawl used in our study, we found no effect on the acous-tic-based measures of door spread, wing spread, and headrope height off-bottom. However, the sensitivity of the trawl to 7 m of warp offset could be seen as footrope distances off-bottom increased slightly (particularly in the center region of the net where flatfish escapement is highest), and as the width of the bridle path responsible for flatfish herding, together with the effective net width, was reduced. For this survey trawl, a NOAA threshold value of 4% should be considered a maximum. A more conservative value (less than 4%) would likely reduce potential bias in estimates of relative abundance caused by large differences in warp length approaching 7 m.

Poder local, cidadania e participação popular no município de Maricá: uma análise crítica das regras do jogo

O tema que nos propomos a estudar é o Poder local, cidadania e participação popular no município de Maricá. A delimitação espaço temporal de nosso projeto situa-se na cidade de Maricá, localizada na Sub-região dos Lagos, no Estado do Rio de Janeiro, a partir do ano de 2009, tendo como pano de fundo as especificidades da formação social brasileira e as determinações estruturais resultantes da mundialização do capital. É importante ressaltar que o termo participação popular pertinente a este estudo refere-se à criação ou ampliação de canais institucionais para intervenção da população no controle social ou na construção do debate orçamentário nas cidades, que exigem estratégias políticas que são absolutamente fundamentais para a construção de uma nova sociedade pautada em princípios radicalmente democráticos.As contradições e as possibilidades da luta pelo direito à cidade, frente à ampliação mercantilização do espaço e a tradição clientelista na cidade de Maricá, foram os desafios que procuraremos responder nesta tese. Para tal, elencamos as seguintes hipóteses: 1) a disputa de projetos societários, a partir da luta de classes, pode ser identificada nas cidades através das propostas antagônicas de cidade-mercadoria e do direito à cidade, contradições estas que se reproduzem inclusive em governos municipais comprometidos com a ampliação dos canais de participação popular; 2) a gestão participativa municipal pode tanto contribuir para a subjetivação das classes subalternas no sentido das mesmas intervirem e até modificarem a esfera pública, quanto se tornar um espaço instrumental ao clientelismo e/ou associativismo local; 3) para evitar tal distorção é importante que agentes contestatórios da sociedade civil retomem o tensionamento de canais institucionais de participação popular nas cidades, enquanto estratégia de ampliação da esfera pública, visto que tais espaços têm sido ocupados por agentes muito mais colaborativos que conflituosos, despolitizando possibilidades, tais como: o orçamento participativo, audiências públicas e os Conselhos Municipais; 4) as cidades do CONLESTE, em especial o município de Maricá, tornaram-se foco do interesse da burguesia nacional e internacional, após as discussões em torno do COMPERJ e do Pré-sal, dificultando e/ou inviabilizado um direcionamento autônomo do poder local em torno das propostas engendradas pela participação popular na cidade, contexto que torna o urgente o tensionamento visando à possibilidade de garantia da função social da cidade, conforme preconiza a Carta Mundial de Direito à Cidade, em especial frente à especulação imobiliária.

Análise Comparativa de Conversores do Sistema Monofásico para o Sistema Trifásico com Número Reduzido de Componentes.

Este trabalho apresenta o estudo comparativo do desempenho de três topologias de conversores do sistema monofásico para o sistema trifásico com número reduzido de componentes, para o acionamento de um motor de indução do tipo rotor gaiola de esquilo. O funcionamento de cada topologia é descrito e simulado digitalmente. O desempenho desses conversores é avaliado em diferentes modos de operação, com sequência de fase positiva ou negativa, com ênfase na qualidade de energia em termos de redução da distorção harmônica total e da melhoria do fator de potência na fonte. Com vistas à redução de custos, foi desenvolvido um protótipo experimental baseado no uso de módulo integrado de chaves semicondutoras de potência e de um microcontrolador de baixo custo. Os resultados experimentais se equiparam aos resultados obtidos por simulação.

Dilatando o corpo da arte: provocações de Um Crime Delicado na literatura e no cinema

A dissertação estuda o romance Um Crime Delicado, de Sérgio SantAnna (1996), ao filme quase homônimo, de Beto Brant (2005), tendo como principal questão a imagem do corpo no contexto sócio-cultural urbano e a sua representação na arte contemporânea. O romance de SantAnna acolhe, na urdidura ficcional, subtemas da maior relevância, tais como o lugar da deficiência física no horizonte de uma cultura hedonista, violência sexual (contra a mulher) e os poderes da crítica de arte (da autojustificação ao desvirtuamento de seus fins). A adaptação fílmica, por sua vez, introduz mudanças na obra de partida que complementam e enriquecem o romance e suas questões. No exercício comparativo, a tradicional discussão sobre as relações interartísticas (calcadas em Lessing), o culto à beleza e respectiva hostilização da feiura, os limites da exacerbação sensorial a partir do uso artístico da nudez provocaram a incorporação de outras obras de arte e de artistas à discussão de conceitos imprescindíveis: o abjeto, o contraditório, a intermidialidade. No primeiro capítulo, circunscrevemos historicamente nosso tema, focalizando a representação do corpo como lugar de multiplicação e relativização de significações; a seguir, apresentamos o painel de contradições que a sociedade excitada do século XX (Christoph Türcke, 2010) projeta sobre a questão corporal; e, para finalizar, propusemos a dilatação teórica do adágio horaciano ut pictura poesis /a poesia é como a pintura ao cinema poético (com suporte teórico de Claus Clüver, 2011, e Wolfgang Moser, 2006). Concluímos sugerindo que as intermidializações propõem novas interpretações aos textos literários, mas podem ser bem mais contundentes como formas de potenciação estética e de crítica social.

Radio over fibre enabled sensing and communications system for in building

This paper describes work on radio over fiber distributed antenna systems for improving the quality of radio coverage for in-building applications. The DAS network has also been shown to provide improved detection for Gen 2 UHF RFID tags. Using pre-distortion to reduce the problem of the RFID second harmonic, a simple heterogeneous sensing and communications system is demonstrated. © 2011 NOrthumbria University.

Evolution of localized blobs of swirling or buoyant fluid with and without an ambient magnetic field.

We investigate the evolution of localized blobs of swirling or buoyant fluid in an infinite, inviscid, electrically conducting fluid. We consider the three cases of a strong imposed magnetic field, a weak imposed magnetic field, and no magnetic field. For a swirling blob in the absence of a magnetic field, we find, in line with others, that the blob bursts radially outward under the action of the centrifugal force, forming a thin annular vortex sheet. A simple model of this process predicts that the vortex sheet thins exponentially fast and that it moves radially outward with constant velocity. These predictions are verified by high-resolution numerical simulations. When an intense magnetic field is applied, this phenomenon is suppressed, with the energy and angular momentum of the blob now diffusing axially along the magnetic field lines, converting the blob into a columnar structure. For modest or weak magnetic fields, there are elements of both types of behavior, with the radial bursting dominating over axial diffusion for weak fields. However, even when the magnetic field is very weak, the flow structure is quite distinct to that of the nonmagnetic case. In particular, a small but finite magnetic field places a lower bound on the thickness of the annular vortex sheet and produces an annulus of counter-rotating fluid that surrounds the vortex core. The behavior of the buoyant blob is similar. In the absence of a magnetic field, it rapidly develops the mushroomlike shape of a thermal, with a thin vortex sheet at the top and sides of the mushroom. Again, a simple model of this process predicts that the vortex sheet at the top of the thermal thins exponentially fast and rises with constant velocity. These predictions are consistent with earlier numerical simulations. Curiously, however, it is shown that the net vertical momentum associated with the blob increases linearly in time, despite the fact that the vertical velocity at the front of the thermal is constant. As with the swirling blob, an imposed magnetic field inhibits the formation of a vortex sheet. A strong magnetic field completely suppresses the phenomenon, replacing it with an axial diffusion of momentum, while a weak magnetic field allows the sheet to form, but places a lower bound on its thickness. The magnetic field does not, however, change the net vertical momentum of the blob, which always increases linearly with time.

Sediment flux at selected coastal sites: proposed time series measurment by particle traps

Particle flux in the ocean reflects ongoing biological and geological processes operating under the influence of the local environment. Estimation of this particle flux through sediment trap deployment is constrained by sampler accuracy, particle preservation, and swimmer distortion. Interpretation of specific particle flux is further constrained by indeterminate particle dispersion and the absence of a clear understanding of the sedimentary consequences of ecosystem activity. Nevertheless, the continuous and integrative properties of the particle trap measure, along with the logistic advantage of a long-term moored sampler, provide a set of strategic advantages that appear analogous to those underlying conventional oceanographic survey programs. Emboldened by this perception, several stations along the coast of Southern California and Mexico have been targeted as coastal ocean flux sites (COFS).

DEVELOPMENT OF MULTI-ANCHOR EARTH RETENTION SYSTEMS.

This paper discusses two projects, the first relating to tests on 'reinforced earth' conducted on the 1. 5 m radius centrifuge at U. M. I. S. T. and the second concerning a short pilot study on the T. R. R. L concept of 'anchored earth' carried out on the 5 m radius Cambridge Geotechnical Centrifuge. The paper proposes a role for centrifugal model testing in design evaluation, whether by the designer himself, his centrification authority, a rival patent holder, or a research worker.

Interpretation of measured profile losses in unsteady wake-turbine blade interaction studies

The interaction of wakes shed by a moving bladerow with a downstream bladerow causes unsteady flow. The meaning of the freestream stagnation pressure and stagnation enthalpy in these circumstances has been examined using simple analyses, measurements and CFD. The unsteady flow in question arises from the behaviour of the wakes as so-called negative-jets. The interactions of the negative-jets with the downstream blades lead to fluctuations in static pressure which in turn generate fluctuations in the stagnation pressure and stagnation enthalpy. It is shown that the fluctuations of the stagnation quantities created by unsteady effects within the bladerow are far greater than those within the incoming wake. The time-mean exit profiles of the stagnation pressure and stagnation enthalpy are affected by these large fluctuations. This phenomenon of energy separation is much more significant than the distortion of the time-mean exit profiles that is caused directly by the cross-passage transport associated with the negative-jet, as described by Kerrebrock and Mikolajczak. Finally, it is shown that if only time-averaged values of loss are required across a bladerow, it is nevertheless sufficient to determine the time-mean exit stagnation pressure.

An investigation into the residual stresses in an aluminium 2024 test weld

This paper uses finite element (FE) analysis to examine the residual stresses generated during the TIG welding of aluminium aerospace alloys. It also looks at whether such an approach could be useful for evaluating the effectiveness of various residual stress control techniques. However, such simulations cannot be founded in a vacuum. They require accurate measurements to refine and validate them. The unique aspect of this work is that two powerful engineering techniques are combined: FE modelling and neutron diffraction. Weld trials were performed and the direct measurement of residual strain made using the ENGIN neutron diffraction strain scanning facility. The predicted results show an excellent agreement with experimental values. Finally this model is used to simulate a weld made using a "Low Stress No Distortion" (LSND) technique. Although the stress reduction predicted is only moderate, the study suggests the approach to be a quick and efficient means of optimising such techniques.

Axial compressor response to inlet flow distortions by a CFD analysis

The usual approach to compressor design considers uniform inlet flow characteristics. Especially in aircraft applications, the inlet flow is quite often non uniform, and this can result in severe performance degradation. The magnitude of this phenomenon is amplified in military engines due to the complexity of inlet duct configurations and the extreme flight conditions. CFD simulation is an innovative and powerful tool for studying inlet distortions and can bring this inside the very early phases of the design process. This project attempts to study the effects of inlet flow distortions in an axial flow compressor trying to minimize the use computer resources and computational time. The first stage of a low bypass ratio compressor has been analyzed and its clean and distorted performance compared outlining the principal changes due to uneven flow distribution: drop in mass flow, increase in pressure and temperature ratios, decrease in surge margin. Three different studies have then been conducted to better understand the effects of the level, the type and the frequency of the distortion.

The unsteady development of a turbulent wake through a downstream low-pressure turbine blade passage

This paper presents two-dimensional LDA measurements of the convection of a wake through a low-pressure (LP) turbine cascade. Previous studies have shown the wake convection to be kinematic but have not provided details of the turbulent field. The spatial resolution of these measurements has facilitated the calculation of the production of turbulent kinetic energy and this has revealed a mechanism for turbulence production as the wake converts through the bladerow. The measured ensemble-averaged velocity field confirmed the previously reported kinematics of wake convection while the measurements of the turbulence quantities showed the wake fluid to be characterised by elevated levels of turbulent kinetic energy (TKE) and to have an anisotropic structure. Based on the measured mean and turbulence quantities, the production of turbulent kinetic energy was calculated. This highlighted a TKE production mechanism that resulted in increased levels of turbulence over the rear suction surface where boundary layer transition occurs. The turbulence production mechanism within the bladerow was also observed to produce more nearly isotropic turbulence. Production occurs when the principal stresses within the wake are aligned with the mean strains. This coincides with the maximum distortion of the wake within the blade passage and provides a mechanism for the production of turbulence outside of the boundary layer.

Reynolds number influence on turbulent blocking effects of a rigid plane boundary (2nd report, direct numerical simulation using townsend's eddy forcing)

The Reynolds number influence on turbulent blocking effects by a rigid plane boundary is studied using direct numerical simulation (DNS). A new forcing method using 'simple model eddies' (Townsend 1976) for DNS of stationary homogeneous isotropic turbulence is proposed. A force field is obtained in real space by sprinkling many space-filling 'simple model eddies' whose centers are randomly but uniformly distributed in space and whose axes of rotation are random. The method is applied to a shear-free turbulent boundary layer over a rigid plane boundary and the blocking effects are investigated. The results show that stationary homogeneous isotropic turbulence is generated in real space using the present method. By using different model eddies with different sizes and rotation speeds, we could change the turbulence properties such as the integral and micro scales, the turbulent Reynolds number and the isotropy of turbulence. Turbulence intensities near the wall showed good agreements with the previous measurement and the linear analysis based on a rapid distortion theory (RDT). The splat effect (i.e., turbulence intensities of the components parallel to the boundary are amplified) occurs near the boundary and the viscous effect prohibits the splat effect at the quasi steady state at low Reynolds number.

Reynolds number influence on turbulent blocking effects of a rigid plane boundary (3rd report, direct numerical simulation on wall blocking effects for anisotropic turbulence)

The Reynolds number influence on turbulent blocking effects by a rigid plane boundary is studied using direct numerical simulation (DNS). A new forcing method proposed in the second report using Townsend's "simple model eddies" for DNS was extended to generate axisymmetric anisotropic turbulence. A force field is obtained in real space by sprinkling many space-filling "simple model eddies" whose centers are randomly but uniformly distributed in space. The axes of rotation are controlled in this study to generate axisymmetric anisotropic turbulence. The method is applied to a shear-free turbulent boundary layer over a rigid plane boundary and the blocking effects for anisotropic turbulence are investigated. The results show that stationary axisymmetric anisotropic turbulence is generated using the present method. Turbulence intensities near the wall showed good agreements with the rapid distortion theory (RDT) for small t (t ≪ TL), where TL. is the eddy turnover time. The splat effect (i. e. turbulence intensities of the components parallel to the surface are amplified) occurs near the boundary and the viscous effect attenuates the splat effect at the quasi steady state at low Reynolds number as for Isotropic turbulence. Prandtl's secondary flow of the second kind does not occur for low Reynolds number flows, which qualitatively agrees with previous observetion in a mixing-box.