Swine effluent treatment using anaerobic digestion at different loading rates

The industrial swine production is characterized by generation of significant effluent amounts that require treatment. The most adopted practices by Brazilian swine farmers have been wastewater storage in lagoons and its subsequent use as a biofertilizer. Nutrient accumulation in soil and water creates the need for an effective management of these residues. The anaerobic digestion process is an important alternative and low-cost treatment for organic matter reduction. However, its efficiency is limited by the digester capacity of solid degradation, especially at low hydraulic retention times. Thus, the present study aimed to verify the behavior of an upflow anaerobic digester by increasing the organic loading rate. This was accomplished in three stages using, as a parameter, volatile solids at 0.5; 1.0 and 1.5 kgVS m-3 d-1, respectively. This digester model proved to be quite robust and effective in swine manure treatment, achieving high efficiency of volatile solid removal at all stages of the study (stage 1: 61.38%; stage 2: 55.18%; and stage 3: 43.18%). Biogas production was directly related to the increasing organic load, reaching 0.14, 0.85, and 0.86 Nm³ kgVS-1add., respectively, with no significant difference (p<0.05) of biogas methane concentration among the studied stages (73.7, 75.0, and 77.9%).

Shewhart's control charts and process capability ratio applied to a sewage treatment station

The current study used statistical methods of quality control to evaluate the performance of a sewage treatment station. The concerned station is located in Cascavel city, Paraná State. The evaluated parameters were hydrogenionic potential, settleable solids, total suspended solids, chemical oxygen demand and biochemical oxygen demand in five days. Statistical analysis was performed through Shewhart control charts and process capability ratio. According to Shewhart charts, only the BOD(5.20) variable was under statistical control. Through capability ratios, we observed that except for pH the sewage treatment station is not capable to produce effluents under characteristics that fulfill specifications or standard launching required by environmental legislation.

Cassava starch extraction effluent treatment in a one phase tubular horizontal pilot reactor with support medium

The cassava starch industries generate a large volume of wastewater effluent that, stabilized in ponds, wastes its biogas energy and pollutes the atmosphere. To contribute with the reversion of this reality, this manipueira treatment research was developed in one phase anaerobic horizontal pilot reactor with support medium in bamboo pieces. The reactor was excavated into the ground and sealed with geomembrane in HDPE, having a volume equal to 33.6 m³ and continuous feeding by gravity. The stability indicators were pH, volatile acidity/total alkalinity ratio and biogas production. The statistical analyses were performed by a completely randomized design, with answers submitted to multivariate analysis. The organical loads in COD were 0.556; 0.670; 0.678 and 0.770 g L-1 and in volatile solids (VS) of 0.659; 0.608; 0.570 and 0.761 g L-1 for the hydraulic retention times (HRT) of 13.0; 11.5; 10.0 and 7.0 days, respectively. The reductions in COD were 88; 80; 88 and 67% and for VS of 76; 77; 65 and 61%. The biogas productions relatively to the consumed COD were 0.368; 0.795; 0.891 and 0.907 Lg-1, for the consumed VS of 0.524; 0.930; 1.757 and 0.952 Lg-1 and volumetric of 0.131; 0.330; 0.430 and 0.374 L L-1 d-1. The reactor remained stable and the bamboo pieces, in visual examination at the end of the experiment, showed to be in good physical conditions.

Soil physical attributes in chemigated banana plantation with wastewater

ABSTRACT The feasibility of using sewage wastewater as a water and nutrient source for plants is an alternative to harness agricultural natural resource, observing its influence on the organic matter dynamics and soil energy. Our objective here was to evaluate the effects of applying different doses of effluent from a sewage treatment plant, in Janaúba – MG, Brazil, over the physical attributes of a soil grown with “Prata Anã” banana. From soil sample collection at depths of 0-20, 20-40, and 40-60 cm, we determined the following soil properties: soil density, total porosity, macroporosity, microporosity, organic matter, clay dispersed in water and stability of soil aggregate. The experimental design was in randomized blocks with four repetitions. Wastewater raising doses promoted increase in suspended solids, contributing to macroporosity reduction at 20-40 and 40-60 cm depths; as well as a reduction in organic matter within 0-20 cm layer. Clay dispersal was observed in the depths of 0-20 cm, being derived from an increase in sodium content. Concurrently, there was a reduction of soil aggregate stability.

Electrocoagulation in the treatment of industrial waters and wastewaters

Chemical coagulation is commonly used in raw water and wastewater treatment plants for the destabilisation of pollutants so that they can be removed in the subsequent separation processes. The most commonly used coagulation chemicals are aluminium and iron metal salts. Electrocoagulation technology has also been proposed for the treatment of raw waters and wastewaters. With this technology, metal cations are produced on the electrodes via electrolysis and these cations form various hydroxides in the water depending on the water pH. In addition to this main reaction, several side reactions, such as hydrogen bubble formation and the reduction of metals on cathodes, also take place in the cell. In this research, the applications of electrocoagulation were investigated in raw water treatment and wastewater applications. The surface water used in this research contained high concentrations of natural organic matter (NOM). The effect of the main parameters – current density, initial pH, electric charge per volume, temperature and electrolysis cell construction – on NOM removal were investigated. In the wastewater treatment studies, the removal of malodorous sulphides and toxic compounds from the wastewaters and debarking effluents were studied. Also, the main parameters of the treatment, such as initial pH and current density, were investigated. Aluminium electrodes were selected for the raw water treatment, whereas wastewaters and debarking effluent were treated with iron electrodes. According to results of this study, aluminium is more suitable electrode material for electrocoagulation applications because it produces Al(III) species. Metal ions and hydroxides produced by iron electrodes are less effective in the destabilisation of pollutants because iron electrodes produce more soluble and less charged Fe(II) species. However, Fe(II) can be effective in some special applications, such as sulphide removal. The resulting metal concentration is the main parameter affecting destabilisation of pollutants. Current density, treatment time, temperature and electrolysis cell construction affect the dissolution of electrodes and hence also the removal of pollutants. However, it seems that these parameters have minimal significance in the destabilization of the pollutants besides this effect (in the studied range of parameters). Initial pH and final pH have an effect on the dissolution of electrodes, but they also define what aluminium or iron species are formed in the solution and have an effect on the ζ-potential of all charged species in the solution. According to the results of this study, destabilisation mechanisms of pollutants by electrocoagulation and chemical coagulation are similar. Optimum DOC removal and low residual aluminium can be obtained simultaneously with electrocoagulation, which may be a significant benefit of electrocoagulation in surface water treatment compared to chemical coagulation. Surface water treatment with electrocoagulation can produce high quality water, which could be used as potable water or fresh water for industrial applications. In wastewater treatment applications, electrocoagulation can be used to precipitate malodorous sulphides to prevent their release into air. Technology seems to be able to remove some toxic pollutants from wastewater and could be used as pretreatment prior to treatment at a biological wastewater treatment plant. However, a thorough economic and ecological comparison of chemical coagulation and electrocoagulation is recommended, because these methods seem to be similar in pollutant destabilisation mechanisms, metal consumption and removal efficiency in most applications.

Haematological and biochemical characteristics of the splenic effluent blood in schistosomal patients undergoing splenectomy

OBJECTIVE: To assess hematological and biochemical features of splenic effluent blood and their influence on the rise of hematological values after splenectomy.METHODS: we studied 20 patients undergoing surgical treatment for schistosomatic portal hypertension. We collected blood samples for CBC, coagulation, bilirubin and albumin in the splenic vein (perioperative) and peripheral blood (immediately pre and postoperative periods).RESULTS: the splenic blood showed higher values of red blood cells, hemoglobin, hematocrit, platelet count, total leukocytes, neutrophils, lymphocytes, monocytes, eosinophils and basophils, as well as reduction of laboratory coagulation parameters in relation to peripheral blood collected preoperatively. In the postoperative peripheral blood there was an increase in the overall leukocytes and in their neutrophil component, and decreased levels of basophils, eosinophils and lymphocytes. The other postoperative variables of complete blood count and coagulation tests were not different compared with the splenic blood. The albumin values were lower postoperatively when compared to preoperative and splenic blood. There were higher values of direct bilirubin in the postoperative period when compared with the preoperative and splenic blood. Postoperative indirect bilirubin was lower compared to its value in the splenic blood.CONCLUSION: hematological and biochemical values of splenic effluent blood are higher than those found in peripheral blood in the presence of schistosomal splenomegaly. However, the splenic blood effluent is not sufficient to raise the blood levels found after splenectomy.

Evolution in the profile of thyroid cancer cases treated in an oncology reference service: what changed in the last 20 years

Objective: To evaluate the characteristics of thyroid carcinoma cases treated at a reference hospital for cancer between 2008 and 2010.Methods: we studied 807 cases and analyzed the following clinicopathologic variables: symptoms, risk factors, diagnostic tests, staging, histological type, treatment performed and complications.Results: Females were more affected, with 660 cases (82%). The average age at diagnosis was 44.5 years. Prior exposure to ionizing radiation was reported by 22 (3%) patients, a family history of thyroid cancer by 89 (11%), and 289 (36%) individuals reported other types of cancer in the family. The fine needle aspiration biopsy was the main parameter for surgical indication and was suggestive of carcinoma in 463 patients (57%). Papillary carcinoma was the most common histological type, with 780 cases (96.6%). There were 728 (90%) total thyroidectomies, 43 (5.3%) reoperations or partial thyroidectomies followed by totalization, 23 (2.8%) extended thyroidectomies and only 13 (1.6%) partial thyroidectomies (lobectomy with isthmectomy). Neck dissection associated with thyroidectomy was done in 158 patients (19.5%). We observed a predominance of tumors classified as T1 in 602 (74.6%) patients. Transient hypocalcemia was the most frequent complication.Conclusion: The results show that the worldwide increase in the incidence of thyroid cancer has changed the profile of patients seen at a referral service. In addition, there were changes in the type of surgical treatment used, with increased use of total thyroidectomy in relation to partial and subtotal ones, and decreased use of elective neck dissections.

Comparative study between patients with acute appendicitis treated in primary care units and in emergency hospitals

Objective: To retrospectively analyze the relationship of time of care, combined with possible post-appendectomy complications, with the promptness of transfer of patients seen in Emergency Care Units (UPA) to the emergency hospital.Methods: We analyzed patients with preoperative diagnosis of acute appendicitis undergoing appendectomy from January to July 2012. Patients were divided into two groups according to the site of the first care. Group A included patients who received initial care directly in the emergency department of the Lourenço Jorge County Hospital (HMLJ) and group B consisted of patients seen in the UPA and forwarded to HMLJ to undergo surgical treatment.Results: the average time between initial treatment and surgery in group A was 29 hours (SD = 21.95) and 54 hours in group B (SD = 54.5). Considering the onset of symptoms, the patients in group A were operated on average 67 hours after (SD = 42.55), while group B, 90 hours (SD = 59.58). After the operation, patients in group A were hospitalized, on average, for 94 hours (SD = 73.53) and group B, 129 hours (SD = 193.42).Conclusion: there was no significant difference in the time elapsed between the onset of symptoms, initial treatment and early surgical treatment, or time elapsed between surgery and discharge.

Complex pulmonary aspergilloma treated by cavernostomy

Objective: To evaluate the effectiveness of cavernostomy in patients with complex fungal balls.Methods: We analyzed the medical records of patients undergoing cavernostomy between January 2005 and May 2013, evaluating: age, gender, preoperative signs and symptoms, predisposing disease, preoperative tests, location of the aspergilloma, etiologic agent, cavernostomy indication, postoperative outcome.Results: Ten patients were male. The mean age was 42.9 years (34-56). The most frequent symptom was repeated pulmonary bleeding. Cavernostomy was proposed for patients at high risk for lung resection. It was performed in 17 patients and all of them had pulmonary tuberculosis sequelae, with cavitations. The indication in all cases was hemoptysis and elimination of phlegm. The cavernostomies were performed in a single surgical procedure. In all 17 patients the cavity was left open after the withdrawal of the mycetoma. In all patients hemoptysis ceased immediately. Operative mortality was 9.5% (1).Conclusion: cavernostomy is an effective treatment alternative in patients at high risk. It may be useful in some patients with complex aspergilloma, irrespective of lung function or bilateral disease. It is technically easy, has low-risk, saves parenchyma, and may be performed in a single operative time.

Iliac artery myointimal hyperplasia in rabbits submitted to angioplasty and treated with Moringa oleifera

Objective: to assess post-angioplasty myointimal hyperplasia in iliac artery of rabbits treated with extract of Moringa oleifera leaves. Methods : we conducted a randomized trial in laboratory animals for five weeks of follow-up, developed in the Vivarium of Pharmaceutical Technology Laboratory of the Universidade Federal da Paraíba. We used rabbits from the New Zealand breed, subjected to a hypercholesterolemic diet and angioplasty of the external iliac artery, randomized into two groups: M200 Group (n=10) - rabbits treated with 200mg/kg/day of Moringa oleifera leaves extract orally; SF group (n=10) - rabbits treated with 0.9% saline orally. After five weeks, the animals were euthanized and the iliac arteries prepared for histology. Histological sections were analyzed by digital morphometry. Statistical analysis was performed using the Student's t test. The significance level was 0.05. Results : there was no significant difference in myointimal hyperplasia between M200 and SF groups when comparing the iliac arteries submitted to angioplasty. Conclusion : there was no difference of myointimal hyperplasia between groups treated with saline and Moringa oleifera after angioplasty.

Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Tertiary Treatment and Re-use of Kraft Pulp Mill Effluent

The efficient use of materials and natural recourses, for ecological and economic reasons, has become more and more important in all industries. In the forest industries this means higher levels of closure in the material circulations of the mills. One possibility to reduce wastewater discharge is to re-use part of the 2nd clarifier effluent as process water. The main target of this thesis was to evaluate the technical suitability of several mechanical and chemical tertiary treatment methods for water re-use. Some of the tested methods seemed to have high potential for the removal of some specific constituents from the wastewater. Tertiary treatment is needed because higher levels of closure may cause problems with increasing amounts of non-process elements in different points of kraft pulp process. The aspect of sustainable development was taken into account by evaluating positive and negative environmental effects of the treatment processes. Environmental benefits can be gained by using some of the tertiary treatment methods tested. These methods should still be researched more for system optimization.

Histologic and inflammatory lamellar changes in horses with oligofructose-induced laminitis treated with a CXCR1/2 antagonist

Abstract: With the hypothesis that blocking chemokine signaling can ameliorate acute laminitis, the aim was to evaluate the therapeutic effect of intravenous DF1681B, a selective antagonist for CXCR1 and CXCR2 (chemokine receptors), in an oligofructose equine laminitis model. To twelve mixed breed clinically healthy hoses with no previous history of hoof-related lameness was administered oligofructose (10g/kg given by nasogastric tube) and divided into two groups: treated (intravenous DF1681B at 30mg/kg 6, 12, 18, and 24h after oligofructose) and non-treated groups. Laminar biopsies were performed before and 12, 36, and 72h after administering oligofructose. Samples were stained with periodic acid-Schiff (PAS) and scored from 0 to 6 according to epidermal cell and basal membrane changes. The IL-1β, IL-6, and CXCL1 RNA expressions were determined by RT-PCR. Parametric and non-parametric tests were used to compare times within each group (P<0.05). The PAS grades and IL-1β and IL-6 RNA expression increased in the non-treated group, but remained constant in the treated horses. In conclusion, DF1681B therapy reduced laminar inflammation and epidermal deterioration in treated horses. CXCR1/2 blockage should be considered therapeutically for equine acute laminitis.

Assimilate partitioning and phytotoxicity in soybean plants treated with herbicides

To investigate the effects of trifluralin, chlorimuron and clomazone on morphology and assimilate partitioning during soybean development, plants were grown in a greenhouse and sampled at 14-day intervals. Clomazone reduced stem and leaf dry matter accumulation at 14 days after emergence (DAE), while trifluralin and chlorimuron reduced plant part dry matter accumulation up to 28 DAE. The number of leaves, plant height, mass and number of pods and seeds, and the shoot/root ratio were not influenced by the herbicides. Roots, stems and leaves were the preferred sinks up to the R2 growth stage, while pods and developing seeds became the preferred sinks later. This order was not altered by the herbicides.

Industrial-Scale hydrothermal carbonization of waste sludge materials for fuel production

Hydrothermal carbonization (HTC) is a thermochemical process used in the production of charred matter similar in composition to coal. It involves the use of wet, carbohydrate feedstock, a relatively low temperature environment (180 °C-350 °C) and high autogenous pressure (up to 2,4 MPa) in a closed system. Various applications of the solid char product exist, opening the way for a range of biomass feedstock materials to be exploited that have so far proven to be troublesome due to high water content or other factors. Sludge materials are investigated as candidates for industrial-scale HTC treatment in fuel production. In general, HTC treatment of pulp and paper industry sludge (PPS) and anaerobically digested municipal sewage sludge (ADS) using existing technology is competitive with traditional treatment options, which range in price from EUR 30-80 per ton of wet sludge. PPS and ADS can be treated by HTC for less than EUR 13 and 33, respectively. Opportunities and challenges related to HTC exist, as this relatively new technology moves from laboratory and pilot-scale production to an industrial scale. Feedstock materials, end-products, process conditions and local markets ultimately determine the feasibility of a given HTC operation. However, there is potential for sludge materials to be converted to sustainable bio-coal fuel in a Finnish context.