Influence of titanium and lutetium on the persistent luminescence of ZrO2

Non-doped as well as titanium and lutetium doped zirconia (ZrO2) materials were synthesized via the sol-gel method and structurally characterized with X-ray powder diffraction. The addition of Ti in the zirconia lattice does not change the crystalline structure whilst the Lu doping introduces a small fraction of the tetragonal phase. The UV excitation results in a bright white-blue luminescence at ca. 500 nm for all the materials which emission could be assigned to the Ti3+ e(g) -> t(2g) transition. The persistent luminescence originates from the same Ti3+ center. The thermoluminescence data shows a well-defined though rather similar defect structures for all the zirconia materials. The kinetics of persistent luminescence was probed with the isothermal decay curve analyses which indicated significant retrapping. The short duration of persistent luminescence was attributed to the quasi-continuum distribution of the traps and to the possibility of shallow traps even below the room temperature. (C) 2012 Optical Society of America

Synthesis, characterization, optical absorption, luminescence and defect centres in Er3+ and Yb3+ co-doped MgAl2O4 phosphors

The Er3+-Yb3+ co-doped MgAl2O4 phosphor powders have been prepared by the combustion method. The phosphor powders are well characterized by X-ray diffraction (XRD) and energy dispersive (EDX) techniques. The absorption spectrum of Er3+/Er3+-Yb3+ doped/co-doped phosphor powder has been recorded in the UV-Vis-NIR region of the electro-magnetic spectrum. The evidence for indirect pumping under 980 nm excitation of Er3+ from Yb3+ was observed in the MgAl2O4 matrix material. Electron spin resonance (ESR) studies were carried out to identify the defect centres responsible for the thermally stimulated luminescence (TSL) process in MgAl2O4:Er3+ phosphor. Three defect centres were identified in irradiated phosphor by ESR measurements which were carried out at room temperature and these were assigned to an O- ion and F+ centres. O- ion (hole centre) appears to correlate with the low temperature TSL peak at 210 A degrees C and one of the F+ centres (electron centre) is related to the high temperature peak at 460 A degrees C.

Self assembled monolayers for engineering of structured inorganic materials in the micrometer and submicrometer range

Deutsch:In der vorliegenden Arbeit konnten neue Methoden zur Synthese anorganischer Materialien mit neuartiger Architektur im Mikrometer und Nanometer Maßstab beschrieben werden. Die zentrale Rolle der Formgebung basiert dabei auf der templatinduzierten Abscheidung der anorganischen Materialien auf selbstorganisierten Monoschichten. Als Substrate eignen sich goldbedampfte Glasträger und Goldkolloide, die eine Mittelstellung in der Welt der Atome bzw. Moleküle und der makroskopischen Welt der ausgedehnten Festkörper einnehmen. Auf diesen Substraten lassen sich Thiole zu einer monomolekularen Schicht adsorbieren und damit die Oberflächeneigenschaften des Substrates ändern. Ein besonderer Schwerpunkt bei dieser Arbeit stellt die Synthese speziell auf die Bedürfnisse der jeweiligen Anwendung ausgerichteten Thiole dar.Im ersten Teil der Arbeit wurden goldbedampfte Glasoberflächen als Template verwendet. Die Abscheidung von Calciumcarbonat wurde in Abhängigkeit der Schichtdicke der adsorbierten Monolage untersucht. Aragonit, eine der drei Hauptphasen des Calciumcarbonat Systems, wurde auf polyaromatischen Amid - Oberflächen mit Schichtdicken von 5 - 400 nm Dicke unter milden Bedingung abgeschieden. Die einstellbaren Parameter waren dabei die Kettenlänge des Polymers, der w-Substituent, die Bindung an die Goldoberfläche über Verwendung verschiedener Aminothiole und die Kristallisationstemperatur. Die Schichtdickeneinstellung der Polymerfilme erfolgte hierbei über einen automatisierten Synthesezyklus.Titanoxid Filme konnten auf Oberflächen strukturiert werden. Dabei kam ein speziell synthetisiertes Thiol zum Einsatz, das die Funktionalität einer Styroleinheit an der Oberflächen Grenze als auch eine Möglichkeit zur späteren Entfernung von der Oberfläche in sich vereinte. Die PDMS Stempeltechnik erzeugte dabei Mikrostrukturen auf der Goldoberfläche im Bereich von 5 bis 10 µm, die ihrerseits über die Polymerisation und Abscheidung des Polymers in den Titanoxid Film überführt werden konnten. Drei dimensionale Strukturen wurden über Goldkolloid Template erhalten. Tetraethylenglykol konnte mit einer Thiolgruppe im Austausch zu einer Hydroxylgruppe monofunktionalisiert werden. Das erhaltene Molekül wurde auf kolloidalem Gold selbstorganisiert; es entstand dabei ein wasserlösliches Goldkolloid. Die Darstellung erfolgte dabei in einer Einphasenreaktion. Die so erhaltenen Goldkolloide wurden als Krstallisationstemplate für die drei dimensionale Abscheidung von Calciumcarbonat verwendet. Es zeigte sich, dass Glykol die Kristallisation bzw. den Habitus des krsitalls bei niedrigem pH Wert modifiziert. Bei erhöhtem pH Wert (pH = 12) jedoch agieren die Glykol belegten Goldkolloide als Template und führen zu sphärisch Aggregaten. Werden Goldkolloide langkettigen Dithiolen ausgesetzt, so führt dies zu einer Aggregation und Ausfällung der Kolloide aufgrund der Vernetzung mehrer Goldkolloide mit den Thiolgruppen der Alkyldithiole. Zur Vermeidung konnte in dieser Arbeit ein halbseitig geschütztes Dithiol synthetisiert werden, mit dessen Hilfe die Aggregation unterbunden werden konnte. Das nachfolgende Entschützten der Thiolfunktion führte zu Goldkolloiden, deren Oberfläche Thiol funktionalisiert werden konnte. Die thiolaktiven Goldkolloide fungierten als template für die Abscheidung von Bleisulfid aus organisch/wässriger Lösung. Die Funktionsweise der Schutzgruppe und die Entschützung konnte mittels Plasmonenresonanz Spektroskopie verdeutlicht werden. Titanoxid / Gold / Polystyrol Komposite in Röhrenform konnten synthetisiert werden. Dazu wurde ein menschliches Haar als biologisches Templat für die Formgebung gewählt.. Durch Bedampfung des Haares mit Gold, Assemblierung eines Stryrolmonomers, welches zusätzlich eine Thiolfunktionalität trug, Polymerisation auf der Oberfläche, Abscheidung des Titanoxid Films und anschließendem Auflösen des biologischen Templates konnte eine Röhrenstruktur im Mikrometer Bereich dargestellt werden. Goldkolloide fungierten in dieser Arbeit nicht nur als Kristallisationstemplate und Formgeber, auch sie selbst wurden dahingehend modifiziert, dass sie drahtförmige Agglormerate im Nanometerbereich ausbilden. Dazu wurden Template aus Siliziumdioxid benutzt. Zum einen konnten Nanoröhren aus amorphen SiO2 in einer Sol Gel Methode dargestellt werden, zum anderen bediente sich diese Arbeit biologischer Siliziumoxid Hohlnadeln aus marinen Schwämmen isoliert. Goldkolloide wurden in die Hohlstrukturen eingebettet und die Struktur durch Ausbildung von Kolloid - Thiol Netzwerken mittels Dithiol Zugabe gefestigt. Die Gold-Nanodrähte im Bereich von 100 bis 500 nm wurden durch Auflösen des SiO2 - Templates freigelegt.

Untersuchungen zur Löslichkeit von Kobalt und Eisen in TiO 2-Bulk sowie in TiO 2-Nanoproben und deren Einfluss auf die magnetischen Eigenschaften

Co- und Fe-dotierte Rutil- und Anatas-Bulkproben wurden über einen Sol-Gel Prozess und anschließende thermische Behandlung dargestellt und auf ihre Zugehörigkeit zu der Gruppe der verdünnten magnetischen Oxide untersucht. Die Untersuchungen der dotierten Rutil-Proben mittels Röntgenbeugung, Elektronenmikroskopie und magnetischen Methoden zeigen, dass die Löslichkeit von Co und Fe in der TiO2-Modifikation Rutil sehr gering ist. Oberhalb von 1at% Co bzw. Fe wird neben Rutil die Bildung der Oxide CoTiO3 bzw. Fe2TiO5 beobachtet. Weitere thermische Behandlung im Argon-H2-Strom führte aufgrund der Bildung von metallischem Co bzw. Fe zu einem ferromagnetischen Verhalten. Die TiO2-Modifikation Anatas besitzt eine höhere Löslichkeit, so dass erst oberhalb von 4at% Co bzw. 10at% Fe die Phasen Co3O4 bzw. FeTiO3 neben Anatas auftreten. Entsprechende Proben zeigen ein paramagnetisches Verhalten. Oberhalb der Löslichkeitsgrenze führt die Reduktion im Argon-H2-Strom zu einem ferromagnetischen Verhalten, welches auf metallisches Co bzw. Fe zurückzuführen ist. Analog zu den Bulkproben wurden Co- und Fe-dotierte TiO2-Nanodrähte hergestellt. Das magnetische Verhalten der Fe-dotierten TiO2-Nanodrähte entspricht dem der Fe-dotierten Anatas-Bulkproben. Dagegen führt die Co-Dotierung nicht zu einem Einbau in die TiO2-Nanodrähte, sondern zur Bildung von CoOx-Nanopartikeln. Die entsprechenden Proben zeigen ein schwach ferromagnetisches Verhalten. Dies ist jedoch nicht auf eine ferromagnetische Dotierung der TiO2-Nanodrähte zurückzuführen, sondern auf nicht kompensierte Momente an den Oberflächen der als Verunreinigungen auftretenden CoOx-Nanopartikel. Zusammenfassend wird festgestellt, dass die Löslichkeit von Co und Fe in TiO2 für die Ausbildung eines ferromagnetischen Verhaltens zu gering ist. Der beobachtete Ferromagnetismus lässt sich eindeutig auf magnetische Verunreinigungen zurückführen. Somit können die dotierten TiO2 Proben nicht den verdünnten magnetischen Oxiden zugeordnet werden.

Sintesi e caratterizzazione di nanoparticelle di ossido di stagno dopate

In the last years, new materials have been developed in the broad area of nanoscience. Among them, an emergent class characterized by excellent electrical conductivity properties as well as high optical transmittance in the visible region are TCOs (Transparent Conducting Oxides). Due to their versatile properties, they have found many applications in a lot of optoelectronic devices, such as solar cells, liquid crystal displays, touch-panel displays, gas sensors, to cite a few examples. Different research groups have studied and characterized the TCOs. In this context, a new synthetic method has been developed to produce FTO nanocrystals (Fluorine-doped Tin Oxide NCs) in Prof. Pinna’s lab at the Humboldt University in Berlin. FTO belongs to the TCO category, and they have been studied as a promising alternative to ITO NCs (Indium Tin Oxide) which represent the standard TCO material in terms of properties and performances. In this work, FTO NCs have been synthesized using the “benzyl alcohol route” (a non-aqueous sol-gel method) via microwave, which permits to produce FTO particles with good properties as revealed by the characterizations performed, employing a cheap, fast and clean method.

Proliferation, differentiation and gene expression of osteoblasts in boron-containing associated with dexamethasone deliver from mesoporous bioactive glass scaffolds

Boron is one of the trace elements in the human body which plays an important role in bone growth. Porous mesopore bioactive glass (MBG) scaffolds are proposed as potential bone regeneration materials due to their excellent bioactivity and drug-delivery ability. The aims of the present study were to develop boron-containing MBG (B-MBG) scaffolds by sol-gel method and to evaluate the effect of boron on the physiochemistry of B-MBG scaffolds and the response of osteoblasts to these scaffolds. Furthermore, the effect of dexamethasone (DEX) delivery in B-MBG scaffold system was investigated on the proliferation, differentiation and bone-related gene expression of osteoblasts. The composition, microstructure and mesopore properties (specific surface area, nano-pore volume and nano-pore distribution) of B-MBG scaffolds have been characterized. The effect of boron contents and large-pore porosity on the loading and release of DEX in B-MBG scaffolds were also investigated. The results have shown that the incorporation of boron into MBG scaffolds slightly decreases the specific surface area and pore volume, but maintains well-ordered mesopore structure and high surface area and nano-pore volume compared to non-mesopore bioactive glass. Boron contents in MBG scaffolds did not influence the nano-pore size distribution or the loading and release of DEX. B-MBG scaffolds have the ability to maintain a sustained release of DEX in a long-term span. Incorporating boron into MBG glass scaffolds led to a controllable release of boron ions and significantly improved the proliferation and bone-related gene expression (Col I and Runx2) of osteoblasts. Furthermore, the sustained release of DEX from B-MBG scaffolds significantly enhanced alkaline phosphatase (ALP) activity and gene expressions (Col I, Runx2, ALP and BSP) of osteoblasts. These results suggest that boron plays an important role in enhancing osteoblast proliferation in B-MBG scaffold system and DEX-loaded B-MBG scaffolds show great potential as a release system to enhance osteogenic property for bone tissue engineering application.

Estudo da cinética da tirosinase imobilizada em nanopartícula de sílica com obtenção de revestimento de eumelanina

Melanina é um polímero constituído por uma grande heterogeneidade de monômeros tendo como característica comum a presença de grupos indóis. Por outro lado, a eumelanina produzida pela oxidação enzimática da tirosina é um polímero mais simples constituído principalmente de monômeros 5,6-dihidroxindol (DHI) e de indol-5,6-quinona (IQ). Tirosinase é a enzima chave na produção de melanina, sendo que a sua atividade cinética é medida em função da formação do intermediário dopacroma. Nanopartículas (NPs) de sílica são partículas nanométricas compostas de oxido de silício e são obtidas pelo processo sol-gel desenvolvido por Stöber de hidrólise e condensação de tetraetilortosilicato (TEOS), usando etanol como solvente em meio alcalino. As NPs foram funcionalizadas com 3-Aminopropiltrietoxissilano (ATPES) e depois com glutaraldeído. Este último permitiu a imobilização da tirosinase na superfície da sílica. Caracterizamos as NPs antes e após a reação da enzima, a atividade catalítica da enzima ligada à NP e o mecanismos de formação de melanina na superfície da sílica. As NPs foram caracterizadas por espectrofotometria de absorção e de reflectância, termogravimetria e microscopia eletrônica. A síntese da NP de sílica retornou partículas esféricas com 55nm de diâmetro e a funcionalização da partícula mostrou modificar eficientemente a sua superfície. A imobilização da tirosinase por ligação covalente foi de 99,5% contra 0,5% da adsorção física. A atividade da tirosinase foi caracterizada pela formação de dopacroma. O Km da enzima imobilizada não sofreu alteração em comparação com a tirosinase livre, mas a eficiência catalítica - que considera a eficiência recuperada - foi de apenas 1/3 para a enzima ligada covalentemente, significando que 2/3 das enzimas ligadas não estão ativas. Obtivemos NPs revestidas com melanina a partir de oxidação de tirosina solubilizada em duas preparações: NP com tirosinase ligada covalentemente na superfície e NP funcionalizada com glutaraldeido dispersa em solução de DHI e IQ. O revestimento de melanina foi na forma de um filme fino com espessura ~1,9nm, conferindo perfil de absorção luminosa equivalente ao da própria melanina. Mostramos que o mecanismo de polimerização passa pela oxidação da tirosina pela tirosinase, que gera intermediários oxidados (principalmente DHI e IQ) que vão para solução (mesmo quando a tirosinase está ligada covalentemente na sílica). Estes intermediários ligam-se ao glutaraldeido e a superfície da sílica passa a funcionar como ambiente de polimerização da melanina.

Otimização da inativação fotodinâmica de E. coli por fotossensibilizadores veiculados por nanopartículas de sílica

A nanotecnologia tem sido aplicada para o desenvolvimento de materiais para diversas aplicações inclusive na inativação de patógenos. As nanopartículas de sílica (npSi) destacam-se pela alta área superficial, facilidade na alteração da superfície para aumento da eficiência adsortiva, penetrabilidade e toxicidade para bactérias gram-negativas sendo biocompatíveis para células de mamíferos e mais foto-estáveis que a maioria dos compostos orgânicos. Devido as suas vantagens, as npSi podem ser usadas para veicular fotossensibilizadores (FSs) uma vez que permitem sua utilização em solução aquosa em que os FSs geralmente são insolúveis. Além disso, o uso de FSs em vez de antibióticos, permite a inativação microbiológica pela Terapia Fotodinâmica sem que as bactérias adquiram resistência por mecanismos genéticos. Esse processo ocorre pela interação entre um FS, luz e oxigênio molecular produzindo oxigênio singleto que é extremamente reativo danificando estruturas celulares. O objetivo desse estudo foi otimizar a fotoinativação dinâmica de E .coli utilizando Azul de Metileno (AM) e Azul de Toluidina O (ATO) veiculados por npSi. As npSi foram preparadas pela metodologia sol-gel, caracterizadas por microscopia eletrônica de varredura (MEV) e submetidas à adsorção de AM e ATO em sua superfície. A presença de AM e ATO na superfície das npSi foram analisadas por espectroscopia no infravermelho; espectroscopia de fluorescência por raio-X e análise termogravimétrica. O planejamento experimental, iniciado pelo fatorial 23 e modelado ao composto central em busca das condições ótimas foi adotado pela primeira vez nessa aplicabilidade, visando a fotoinativação de E. coli empregando AM e ATO em solução e em seguida com npSi. AM e ATO veiculados por npSi permitem a fotoinativação em concentrações mais baixas de FS (20 e 51% respectivamente), causando desestruturação da integridade bacteriana demonstrada por MEV. Os resultados sugerem que a veiculação de AM e ATO por npSi é extremamente efetiva para a fotoinativação dinâmica de E. coli e que o planejamento composto central pode levar à completa inativação das bactérias.

Mesoporous bioactive glasses. I. Synthesis and structural characterization

Highly ordered mesoporous bioactive glasses (MBGs) with different compositions have been synthesized by a combination of surfactant templating, sol-gel method and evaporation-induced self-assembly (EISA) processes. The texture properties and compositional homogeneity of MBGs have been characterized and compared with conventional bioactive glasses (BGs) synthesized in the absence of surfactants by evaporation method. The formation mechanism (pore - composition dependence) and compositional homogeneity in the case of MBG materials are different from those in conventional BGs. Unlike conventional sol-gel-derived BGs that shows a direct correlation between their composition and pore architecture, MBGs with different compositions may possess similar pore volume and uniformly distributed pore size when the same structure-directing agent is utilized. The framework of MBG is homogeneously distributed in composition at the nanoscale and the inorganic species generally exists in the form of amorphous phase. MBGs calcined at temperatures

Characterization of titanium phosphate as electrolytes in fuel cells

Titanium phosphate is currently a promising material for proton exchange membrane fuel cells applications (PEMFC) allowing for operation at high temperature conditions. In this work, titanium phosphate was synthesized from tetra iso-propoxide (TTIP) and orthophosphoric acid (H3PO4) in different ratios by a sol gel method. High BET surface areas of 271 m(2).g(-1) were obtained for equimolar Ti:P samples whilst reduced surface areas were observed by varying the molar ratio either way. Highest proton conductivity of 5.4 x 10(-2) S.cm(-1) was measured at 20 degrees C and 93% relative humidity (RH). However, no correlation was observed between surface area and proton conductivity. High proton conductivity was directly attributed to hydrogen bonding in P-OH groups and the water molecules retained in the sample structure. The proton conductivity increased with relative humidity, indicating that the Grotthuss mechanism governed proton transport. Further, sample Ti/P with 1:9 molar ratio showed proton conductivity in the order of 10(-1) S.cm(-1) (5% RH) and similar to 1.6x10(-2) S.cm(-1) (anhydrous condition) at 200 degrees C. These proton conductivities were mainly attributed to excess acid locked into the functionalized TiP structure, thus forming ionisable protons.

Organometallic precursors for pillared clay synthesis

The synthetic hectorite, laponite has been used within the paper industry to produce mildly conducting paper for use in electrographic printing. The aim of this research was to modify laponite in order to improve the electrical conductivity. In a continuation of a previous investigation involving organotin intercalation of laponite, the organotin precursor (p-CH3,OC6H4)4Sn was synthesised and characterised using Mass Spectroscopy, Infrared Spectroscopy and elemental analysis. Results of intercalation with this compound and a range of organobismuth and organoantimony compounds suggested that a halide content within the precursor was necessary for improvement in conductivity to be observed. Organometallic intercalation of a range of organotellurium compounds with laponite provided evidence that a hydrolysis reaction on the clay surface followed by the release of hydrochloric acid was an important first step if a reaction was to occur with the clay. Atomic Absorption Spectroscopy studies have shown that the acid protons underwent exchange with the interlayer sodium ions in the clay to varying degrees. Gas-liquid Chromatography and Infrared Spectroscopy revealed that the carbon-tellurium bond remained intact. Powder X-ray diffraction revealed that there had been no increase in the basal spacing. The a.c. conductivity of the modified clays in the form of pressed discs was studied over a frequency range of 12Hz - 100kHz using two electrode systems, silver paste and stainless steel. The a.c. conductivity consists of two components, ionic and reactive. The conductivity of laponite was increased by intercalation with organometallic compounds. The most impressive increase was gained using the organotellurium precursor (p-CH3OC6H4)2TeCl2. Conductivity investigations using the stainless steel electrode where measurements are made under pressure showed that in the case of laponite, where poor particle-particle contact exists at ambient pressure, there is a two order of magnitude increase in the measured a.c. conductivity. This significant increase was not seen in modified laponites where the particle-particle contact had already been improved upon. Investigations of the clay surface using Scanning Electron Microscopy suggested that the improvement in particle-particle contact is the largest factor in the determination of the conductivity. The other important factor is the nature and the concentration of the interlayer cations. A range of clays were synthesised in order to increase the concentration of sodium interlayer cations. A sol-gel method was employed to carry out these syntheses. A conductivity evaluation showed that increasing the concentration of the sodium cations within the clay led to an increase in the conductivity.

Identifying the active phase in Cs-promoted MgO nanocatalysts for triglyceride transesterification

Background: Biodiesel is a clean-burning, renewable and biodegradable diesel fuel substitute derived from animal fats and plant oils, which may play an important role in replacing diminishing fossil fuel reserves and combating climate change. Conventional biodiesel production uses soluble base catalysts, such as Na or K alkoxides, to convert oils into fuel, and as a result requires energy intensive aqueous quench cycles to isolate the biodiesel product. Results: Cs-doping nanoparticulate MgO, prepared via a novel, supercritical sol-gel method, yields a solid base catalyst with improved activity for the transesterification of pure triacylglycerides (TAGs) and olive oil. Conclusion: Here, X-ray absorption spectroscopy (XAS) is used to probe the local chemical environment of Cs atoms in order to identify the nature of the catalytically active species as CsMg(CO)(HO). © 2013 Society of Chemical Industry.

Structure-sensitive biodiesel synthesis over MgO nanocrystals

Size-controlled MgO nanocrystals were synthesised via a simple sol-gel method and their bulk and surface properties characterised by powder XRD, HRTEM and XPS. Small, cubic MgO single crystals, generated by low temperature processing, expose weakly basic (100) surfaces. High temperature annealing transforms these into large, stepped cuboidal nanoparticles of periclase MgO which terminate in more basic (110) and (111) surfaces. The size dependent evolution of surface electronic structure correlates directly with the associated catalytic activity of these MgO nanocrystals towards glyceryl tributyrate transesterification, revealing a pronounced structural preference for (110) and (111) facets. © 2009 The Royal Society of Chemistry.

Síntese e caracterização de nanopartículas magnéticas de Co e Ni com aplicação em magneto hipertermia

Nanoparticles are importante for the study of new phenomena and for the development of new applications. Metallic magnetic nanoparticles like Cobalt and Nickel are important for their applications in nanoscience and nanotechnology. In this work, we report on the synthesis and characterization of Ni and Co nanoparticles. The nanoparticles were prepared by the modi- ed sol-gel method and were formed in the pore-network of the biopolymer quitosan. The reduction occurred in absence of H2 ux. The metallic particles and their monoxides have a face-centered- cubic structure. The metallic particles sizes ranged from 59 to 77 nm and from 19 to 50 nm for Ni and Co, respectively. Their monoxides chemically passivated the metallic cores, and after several weeks we have not observed further increase in oxidation. The synthesis method was tuned to obtain mainly the ferromagnetic phase. The system behaves like a core/shell structure with a ferromagnetic core and an antiferromagnetic shell. Exchange bias e ect was observed at temperatures below the Néel temperature. Both systems were submitted to an alternated magnetic eld and the heat released by the particles increased the temperature to 140°C in an interval of 5 min. Similar studies in samples dispersed in water increased the temperatures to 40-59°C, these results suggest that these materials are candidates for magnetic hyperthermia.

Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.