Kartonkipakkauskoneen dynaaminen kireydenhallinta

Työssä tutkitaan PI-säätimen käyttöä dynaamisessa kireydensäädössä ilman varsinaista kireyden takaisinkytkentää. Kireyttä säädetään epäsuorasti käyttämällä takaisinkytkentätietona kahden telan välistä paikkaeroa. Kireyssäädin toteutetaan nopeussäätimen rinnalle. Rinnakkaisrakenteella pyritään kireyden muutoksiin nopeasti reagoivaan säätöratkaisuun. Rakenne toteutetaan osaksi taajuusmuuttajan säätöketjua. Työssä esitetään telasysteemin simulointimalli, jonka toimivuus varmistetaan käytännön mittauksin. Lisäksi työssä arvioidaan kireyssäädön toimintaa dynaamisessa kireydensäädössä simulointien ja testilaitteistolla suoritettavien mittausten perusteella.

Mikkelin Pursialan pohjavesialueen haitta-aineet

Mikkelin talousvedestä kahden kolmasosan tullessa Pursialan pohjavesialueelta on alueen suojeleminen tärkeää. Pohjaveden laatua uhkaavat etenkin alueella sattuneet pohjavedenpilaantumistapaukset. Merkittävimmät pohjaveden pilaantumistapaukset ovat VAPO Oy:n sahan aiheuttama pohjaveden pilaantuminen kloorifenoleilla (CP) ja VR:n ratapölkkykyllästämön aiheuttama pohjaveden pilaantuminen kreosoottiöljyllä sekä Rinnekadun Nesteen aiheuttama pohjaveden pilaantuminen MTBE:llä. Alueella on tehty tutkimuksia ja kunnostuksia pilaantumiin liittyen, mutta näiden tuloksia ei ole aikaisemmin koottu yhteen. Tämän työn tavoitteena oli koota tulokset samaan aineistoon. Työssä keskityttiin kloorifenolien leviämisen tarkasteluun sen Pursialan pohjavedenottamolle muodostaman suurimman uhan vuoksi. Kallioperätietojen, maanpintatietojen ja näytetietojen pohjalta laadittiin myös pienoismalli CP-pilaantuman leviämisen kokonaiskuvan hahmottamiseksi. Työn tavoitteena oli lisäksi tehdä riskitarkastelua CP-pilaantumaan liittyen ja etsiä keinoja hallita havaittuja riskejä. Riskinhallintaan liittyen työssä tutkittiin kloorifenoleilla pilaantuneen alueen maaperä- ja kalliotietoja sekä pohjaveden laatutietoja. Pursialan pohjavedessä on runsaasti rautaa ja mangaania sekä aggressiivista hiilihappoa. Pohjaveden pH on alueella noin 6,5, lämpötila noin 7,5 ºC ja happipitoisuus noin 0,7 mg/l. Pursialan kaupunginalueen kallioperässä on havaittavissa VAPO Oy:n sahalta vedenottamolle etenevä kalliopainanne, jota pitkin CP etenee. Alueen kallioperä on kiillegneissiä, jossa on pohjois–etelä-suuntaista rakoilua. Maaperätuloksien perusteella on havaittavissa vettä hyvin johtavien maakerrosten jatkuminen koko vedenottamon ja sahan välisen matkan, mikä tarkoittaa, että CP-pitoisella pohjavedellä voi olla aiemmin oletettua nopeampikin yhteys sahalta vedenottamolle. Suurin CP-pitoisuus noin 100 000 µg/l on mitattu KY-5-altaan kohdalle asennetun M14-pohjavesiputken pohjasta. Talousvesiasetuksen raja-arvo CP:lle on 10 µg/l. Sahan ja vedenottamon puolivälissä on havaittu yli 10 000 µg/l meneviä CP-pitoisuuksia. Suurin vedenottamon kaivoista (kaivo 10) mitattu pitoisuus on 149 µg/l. Jakotukilta raakavedestä otetuissa näytteissä tai talousvedessä ei ole kuitenkaan havaittu talousvesiasetuksen ylittäviä CP-pitoisuuksia. Pienoismallin perusteella CP sijaitsee sahan alueella lähellä kallionpintaa ja hajaantuu koko pohjavesipatjaan vedenottamolle päin mentäessä. CP-mittaustuloksissa on havaittavissa pulssimaisuutta. Tämä johtuu todennäköisesti Saimaan pinnan vaihtelun seurauksena muuttuvasta rantaimeytyneen pohjaveden määrästä. Saimaan pinnan nousu näyttäisi tuloksien perusteella nostavan CP-pitoisuuksia saha-alueella ja laskevan lähellä vedenottamoa. Pohjaveden pintatietojen perusteella tehdyn tarkastelun mukaan pohjavesi voi kulkeutua sahalta vedenottamolle parhaimmillaan noin vuodessa. Työssä arvioitiin KY-5–liuoksen vuosittaiseksi käyttömääräksi noin 648–970 m3. Allassakkaa arvioitiin syntyneen yhteensä noin 10–31 m3. Pohjaveteen arvioitiin joutuneen toiminnan aikana yhteensä noin 3 000–4 000 kg CP:tä. Kloorifenolit esiintyvät pohjavedessä lähes täysin kloorifenolaatteina. Kloorifenolien hajoaminen ja muuntuminen pohjavedessä on epätodennäköistä. Käsitteellisen mallin mukaan kloorifenolipilaantuman suurimmat riskit aiheutuvat kloorifenolien mahdollisuudesta pilata Pursialan vedenottamon talousvesi. Tällä hetkellä riskejä hallitaan kloorifenolien leviämisen tarkkailulla, sahan ja vedenottamon puolivälissä sijaitsevalla koepumppauksella sekä varautumalla aktiivihiilijauheen syöttöön talousvesiprosessiin. Koepumppauksen avulla on saatu ylös tällä hetkellä noin 69 kg kloorifenoleita. Tutkimuksen perusteella suositeltavimmat riskinhallintatoimet tulevaisuudessa ovat sahalla sijaitseva kunnostuspumppaus, sahan ja vedenottamon väliin sijoittuva suojapumppaus- ja vesiverhoyhdistelmä sekä sahan rannan kautta tapahtuvan rantaimeytymisen estäminen.

Airway surgery for obstructive sleep apnea and partial upper airway obstruction during sleep

This study analyzed the feasibility and efficacy of surgical therapies in patients with sleep-disordered breathing ranging from partial upper airway obstruction during sleep to severe obstructive sleep apnea syndrome. The surgical procedures evaluated were tracheostomy, laser-assisted uvulopalatoplasty (LUPP) and uvulopalatopharyngoplasty (UPPP) with laser or ultrasound scalpel. Obstructive sleep apnea and partial upper airway obstruction during sleep were measured with the static charge-sensitive bed (SCSB) and pulse oximeter. The patients with severe obstructive sleep apnea syndrome were treated with tracheostomy. Palatal surgery was performed only if the upper airway narrowing occurred exclusively at the soft palate level in patients with partial upper airway obstruction during sleep. The ultrasound scalpel technique was compared to laser-assisted UPPP. The efficacy of LUPP to reduce partial upper airway obstruction during sleep was assessed and histology of uvulopalatal specimen was compared to body fat distributional parameters and sleep study findings. Tracheostomy was effective therapy in severe obstructive sleep apnea. Partial upper airway obstruction and arterial oxyhemoglobin desaturation index during sleep decreased significantly after LUPP. The minimal retropalatal airway dimension increased and soft palate collapsibility decreased at the level where the velopharyngeal obstruction had occurred before the surgery. Ultrasound scalpel did not offer any significant benefits over the laser-assisted technique, except fewer postoperative haemorrhage events. The loose connective tissue as a manifestation of edema was the only histological finding showing correlation with partial upper airway obstruction parameters of SCSB. Tracheostomy remains a life-saving therapy and also long-term option when adherence to CPAP fails in patients with obstructive sleep apnea syndrome. LUPP effectively reduces partial upper airway obstruction during sleep provided that obstruction at the other levels than the soft palate and uvula were preoperatively excluded. Technically the ultrasound scalpel or laser surgeries are equal. In patients with partial upper airway obstruction the loose connective tissue is more important than fat accumulation in the soft palate. This supports the hypothesis that edema is a primary trigger for aggravation of upper airway narrowing during sleep at the soft palate level and evolution towards partial or complete upper airway obstruction during sleep.

Algorithmic Solutions for Combinatorial Problems in Resource Management of Manufacturing Environments

This thesis studies the use of heuristic algorithms in a number of combinatorial problems that occur in various resource constrained environments. Such problems occur, for example, in manufacturing, where a restricted number of resources (tools, machines, feeder slots) are needed to perform some operations. Many of these problems turn out to be computationally intractable, and heuristic algorithms are used to provide efficient, yet sub-optimal solutions. The main goal of the present study is to build upon existing methods to create new heuristics that provide improved solutions for some of these problems. All of these problems occur in practice, and one of the motivations of our study was the request for improvements from industrial sources. We approach three different resource constrained problems. The first is the tool switching and loading problem, and occurs especially in the assembly of printed circuit boards. This problem has to be solved when an efficient, yet small primary storage is used to access resources (tools) from a less efficient (but unlimited) secondary storage area. We study various forms of the problem and provide improved heuristics for its solution. Second, the nozzle assignment problem is concerned with selecting a suitable set of vacuum nozzles for the arms of a robotic assembly machine. It turns out that this is a specialized formulation of the MINMAX resource allocation formulation of the apportionment problem and it can be solved efficiently and optimally. We construct an exact algorithm specialized for the nozzle selection and provide a proof of its optimality. Third, the problem of feeder assignment and component tape construction occurs when electronic components are inserted and certain component types cause tape movement delays that can significantly impact the efficiency of printed circuit board assembly. Here, careful selection of component slots in the feeder improves the tape movement speed. We provide a formal proof that this problem is of the same complexity as the turnpike problem (a well studied geometric optimization problem), and provide a heuristic algorithm for this problem.

Teollisuusprosessien signaalien automaattinen analysointi

Diplomityössä kehitettiin menetelmiä teollisuusprosessien signaalien automaattiseen havainnointiin ja luotiin työkalu tulosten esittämiseen. Työn tarkoituksena on nopeuttaa ja helpottaa prosessin ongelmien ratkaisua luokittelemalla signaalit matemaattisten menetelmien avulla. Koska prosessin mittaussignaalit ovat pääasiassa stokastisia, eli niitä ei voida etukäteen ennustaa, käsitellään signaaleita tilastomatemaattisin keinoin. Työstä rajattiin mittaushistorian käyttö, joten värähtelyiden tunnistus toteutettiin taajuusanalyysin avulla. Korrelaation avulla löydetään samankaltaiset signaalit. Testeissä todettiin, että työssä kehitetyt havainnoinnit toimivat eri näytteenottotaajuuksilla ja työkalun suoritusnopeus todettiin hyväksi. Lopuksi esiteltiin todellinen teollisuusprosessin ongelma ja siihen mahdollisia ratkaisuja.

Dieselmoottorin analogisen kierrosnopeusmittauksen digitalisointi

Työssä suunnitellaan kierrosnopeusmittauksen toteutus vanhaan Ford -teollisuusdieseliin käyttäen moottorin alkuperäistä kierrosnopeusanturia. Anturi kunnostetaan vaihtamalla vanha, palanut käämi uuteen digitaaliseen järjestelmään soveltuvaan käämiin. Sen toimin-ta halutulla kierrosnopeusalueella varmistetaan mittauksin ja tämän perusteella suunnitel-laan kytkentä sen liittämiseksi kierrosnopeuden laskevaan mikrokontrolleriin. Kytkennän toimivuutta testataan simuloimalla ennen prototyypin rakentamista. Erilaisia vaihtoehtoja analogisen näytön toteuttamiseksi tutkitaan ja niistä valitaan yksi ve-nekäyttöön soveltuva, joka toteutetaan järjestelmän näyttöratkaisuksi. Järjestelmälle suunnitellaan piirilevy, jolle prototyyppi kasataan. Mikrokontrollerille koodataan C -ohjelmointikielellä ohjelma, joka laskee dieselmoottorin kierrosnopeuden anturipulssien perusteella ja ohjaa näyttöä.

Evaluation of energy efficiency and best available techniques in pumping processes

The potential for enhancing the energy efficiency of industrial pumping processes is estimated to be in some cases up to 50 %. One way to define further this potential is to implement techniques in accordance to definition of best available techniques in pumping applications. These techniques are divided into three main categories: Design, control method & maintenance and distribution system. In the theory part of this thesis first the definition of best available techniques (BAT) and its applicability on pumping processes is issued. Next, the theory around pumping with different pump types is handled, the main stress being in centrifugal pumps. Other components needed in a pumping process are dealt by presenting different control methods, use of an electric motor, variable speed drive and the distribution system. Last part of the theory is about industrial pumping processes from water distribution, sewage water and power plant applications, some of which are used further on in the empirical part as example cases. For the empirical part of this study four case studies on typical pumping processes from older Master’s these were selected. Firstly the original results were analyzed by studying the distribution of energy consumption between different system components and using the definition of BAT in pumping, possible ways to improve energy efficiency were evaluated. The goal in this study was that by the achieved results it would be possible to identify the characteristic energy consumption of these and similar pumping processes. Through this data it would then be easier to focus energy efficiency actions where they might be the most applicable, both technically and economically.

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.

Hammashihnajohdeakseleiden liikkeiden synkronointi

Nykyisessä valmistusteollisuudessa erilaisten robottien ja automatisoitujen tuotantovaiheiden rooli on erittäin merkittävä. Tarkasti suunnitellut liikkeet ja toimintavaiheet voidaan nykyisillä järjestelmillä ajoittaa tarkasti toisiinsa nähden, jolloin erilaisten virhetilanteidenkin sattuessa järjestelmä pystyy toimimaan tilanteen edellyttämällä tavalla. Automatisoinnin etuna on myös tuotannon muokkaaminen erilaisten tuotteiden valmistamiseen pienillä muutoksilla, jolloin tuotantokustannukset pysyvät matalina myös pienten valmistuserien tapauksissa. Usean akselin laitteissa eli niin sanotuissa moniakselikäytöissä laitteen toimintatarkkuus riippuu jokaisen liikeakselin tarkkuudesta. Liikkeenohjauksessa on perinteisesti ollut käytössä myötäkytketty paikkakaskadi, jonka virityksessä otetaan huomioon akselilla olevat erilaiset dynaamiset tilat ja käytettävät referenssit. Monissa nykyisissä hajautetuissa järjestelmissä eli moniakselikäytöissä, joissa jokaiselle akselille on oma ohjauslaite, ei yksittäisen akselin paikkavirhettä huomioida muiden akseleiden ohjauksessa. Työssä tutkitaan erilaisia moniakselijärjestelmien ohjausmenetelmiä ja myötäkytketyn paikkakaskadin toimintaa moniakselikäytössä pyritään parantamaan tuomalla paikkasäätimen rinnalle toinen säädin, jonka tulona on akseleiden välinen paikkaero.

Evolution of Bordetella pertussis post vaccination

Evolution of Bordetella pertussis post vaccination Whooping cough or pertussis is caused by the gram-negative bacterium Bordetella pertussis. It is a highly contiguous disease in the human respiratory tract. Characteristic of pertussis is a paroxysmal cough with whooping sound during gasps of breath after coughing episodes. It is potentially fatal to unvaccinated infants. The best approach to fight pertussis is to vaccinate. Vaccinations against pertussis have been available from the 1940s. Traditionally vaccines were whole-cell pertussis (wP) preparations as part of the combined diphtheria-tetanus-pertussis (DTP) vaccines. More recently acellular pertussis (aP) vaccines have replaced the wP vaccines in many countries. The aP vaccines are less reactogenic and can also be administered to school children and adults. There are several publications reporting variation in the i>B. pertussis virulence factors that are also aP vaccine antigens. This has occurred in the genes coding for pertussis toxin and pertactin about 15 to 30 years after the introduction of pertussis vaccines to immunisation programs. Resurgence of pertussis has also been reported in many countries with high vaccination coverage. In this study the evolution of B. pertussis was investigated in Finland, the United Kingdom, Poland, Serbia, China, Senegal and Kenya. These represent countries with a long history of high vaccination coverage with stable vaccines or changes in the vaccine formulation; countries which established high vaccination coverage late; and countries where vaccinations against pertussis were started late. With bacterial cytotoxicity and cytokine measurements, comparative genomic hybridisation, pulsed-field gel electrophoresis (PFGE), genotyping and serotyping it was found that changes in the vaccine composition can postpone the emergence of antigenic variants. It seems that the change in PFGE profiles and the loss of genetic material in the genome of B. pertussis are similar in most countries and the vaccine-induced immunity is selecting non-vaccine type strains. However, the differences in the formulation of the vaccines, the vaccination programs and in the coverage of pertussis vaccination have affected the speed and timing of these changes.

Field Weakening, Parameters and Operation Range of the Permanent Magnet Traction Motors

The main focus of this thesis is to define the field weakening point of permanent magnet synchronous machine with embedded magnets in traction applications. Along with the thesis a modelling program is made to help the designer to define the field weakening point in practical applications. The thesis utilizes the equations based on the current angle. These equations can be derived from the vector diagram of permanent magnet synchronous machine. The design parameters of the machine are: The maximum rotational speed, saliency ratio, maximum induced voltage and characteristic current. The main result of the thesis is finding out the rated rotational speed, from which the field weakening starts. The action of the machine is estimated at a wide speed range and the changes of machine parameters are examined.

Energy Efficiency of Pumping Medium Consistency Pulp with Centrifugal Pump

Approximately a quarter of electrical power consumption in pulp and paper industry is used in different pumping systems. Therefore, improving pumping system efficiency is a considerable way to reduce energy consumption in different processes. Pumping of wood pulp in different consistencies is common in pulp and paper industry. Earlier, centrifugal pumps were used to pump pulp only at low consistencies, but development of MC technology has made it possible to pump medium consistency pulp. Pulp is a non-Newtonian fluid, which flow characteristics are significantly different than what of water. In this thesis is examined the energy efficiency of pumping medium consistency pulp with centrifugal pump. The factors effecting the pumping of MC pulp are presented and through case study is examined the energy efficiency of pumping in practice. With data obtained from the case study are evaluated the effects of pump rotational speed and pulp consistency on energy efficiency. Additionally, losses caused by control valve and validity of affinity laws in pulp pumping are evaluated. The results of this study can be used for demonstrating the energy consumption of MC pumping processes and finding ways to improve energy efficiency in these processes.

Epälineaaristen regressiomenetelmien vertaaminen robottikäden otemallinnuksessa

Tässä työssä verrattiin monikerrosperseptronin, radiaalikantafunktioverkon, tukivektoriregression ja relevanssivektoriregression soveltuvuutta robottikäden otemallinnukseen. Menetelmille ohjelmoitiin koeympäristö Matlabiin, jossa mallit koestettiin kolmiulotteisella kappaledatalla. Koejärjestely sisälsi kaksi vaihetta. Kokeiden ensimmäisessä vaiheessa menetelmille haettiin sopivat parametrit ja toisessa vaiheessa menetelmät koestettiin. Kokeilla kerättiin dataa menetelmien keskinäiseen vertailuun. Vertailussa huomioitiin laskentanopeus, koulutusaika ja tarkkuus. Tukivektoriregressio löydettiin potentiaaliseksi vaihtoehdoksi mallintamiseen. Tukivektoriregression koetuloksia analysoitiin muita menetelmiä enemmän hyvien koetulosten takia.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Information exchange and disruption risk in multimodal maritime supply chains

Supply chains are becoming increasingly dependent on information ex-change in today’s world, and any disruption can cause severe repercus-sions to the flow of materials in the chain. The speed, accuracy and amount of information are key factors. The aim in this thesis is to address a gap in the research by focusing on information exchange and the risks related to it in a multimodal wood supply chain operating between the Baltic States and Finland. The study involved interviewing people engaged in logistics management in the supply chain in question. The main risk the interviewees identified arose from the sea logistics system, which held a lot of different kinds of information. The threat of breakdown in the Internet connection was also found to hinder the operations significantly. A vulnerability analysis was carried out in order to identify the main actors and channels of infor-mation flow in the supply chain. The analysis revealed that the most important and therefore most vulnerable information-exchange channels were those linking the terminal superintendent, the operative managers and the mill managers. The study gives a holistic picture of the investigated supply chain. Information-exchange-related risks varied greatly. One of the most frequently mentioned was the risk of information inaccuracy, which was usually due to the fact that those in charge of the various functions did not fully understand the consequences for the entire chain.