A 5.6-mW Power Dissipation CMOS Frequency Synthesizer for L1/L2 Dual-Band GPS Application

This paper presents a wide tuning range CMOS frequency synthesizer for dual-band GPS receiver, which has been fabricated in a standard 0.18-um RF CMOS process. With a high Q on-chip inductor, the wide-band VCO shows a tuning range from 2 to 3.6GHz to cover 2.45GHz and 3.14GHz in case of process corner or temperature variation, with a current consumption varying accordingly from 0.8mA to 0.4mA, from a 1.8V supply voltage. The measurement results show that the whole frequency synthesizer costs a very low power consumption of 5.6mW working at L I band with in-band phase noise less than -82dBc/Hz and out-of-band phase noise about -112 dBc/Hz at 1MHz offset from a 3.142GHz carrier.

An Ultra Low Power Non-volatile Memory in Standard CMOS Process for Passive RFID Tags

An ultra low power non-volatile memory is designed in a standard CMOS process for passive RFID tags. The memory can operate in a new low power operating scheme under a wide supply voltage and clock frequency range. In the charge pump circuit the threshold voltage effect of the switch transistor is almost eliminated and the pumping efficiency of the circuit is improved. An ultra low power 192-bit memory with a register array is implemented in a 0.18 mu M standard CMOS process. The measured results indicate that, for the supply voltage of 1.2 volts and the clock frequency of 780KHz, the current consumption of the memory is 1.8 mu A (3.6 mu A) at the read (write) rate of 1.3Mb/s (0.8Kb/s).

LD side-pumped high beam quality passive Q-switched and mode-locked Nd:YAG laser based on SESAM

We report a LD side-pumped fundamental-mode (Mx(2) = 1.35 and My(2) = 1.27) passive Q-switched and mode-locked Nd:YAG laser based on a semiconductor saturable absorber mirror (SESAM). At a pump current of 12.5 A, the average output power of 5.68 W with 80 kHz repetition rate and 2 mu s pulse width of the Q-switched envelope was generated. The repetition rate of the mode-locked pulse within the Q-switched envelope of 88 MHz was achieved.

A low power high linearity baseband for a direct conversation CMMB tuner

An analog baseband circuit made in a 0.35-μm SiGe BiCMOS process is presented for China Multimedia Mobile Broadcasting (CMMB) direct conversion receivers. A high linearity 8th-order Chebyshev low pass filter (LPF) with accurate calibration system is used. Measurement results show that the filter provides 0.5-dB pass-band ripple, 4% bandwidth accuracy, and -35-dB attenuation at 6 MHz with a cutoff frequency of 4 MHz. The current steering type variable gain amplifier (VGA) achieves more than 40-dB gain range with excellent temperature compensation.This tuner baseband achieves an OIP3 of 25.5 dBm, dissipates 16.4 mA under a 2.8-V supply and occupies 1.1 mm~2 of die size.

A Low Power Dissipation Wide-Band CMOS Frequency Synthesizer for a Dual-Band GPS Receiver

This paper presents a wide tuning range CMOS frequency synthesizer for a dual-band GPS receiver,which has been fabricated in a standard 0.18μm RF CMOS process. With a high Q on-chip inductor, the wide-band VCO shows a tuning range from 2 to 3.6GHz to cover 2.45 and 3.14GHz in case of process corner or temperature variation,with a current consumption varying accordingly from 0.8 to 0.4mA,from a 1.8V supply voltage. Measurement results show that the whole frequency synthesizer consumes very low power of 5.6mW working at L1 band with in-band phase noise less than - 82dBc/Hz and out-of-band phase noise about - ll2dBc/Hz at 1MHz offset from a 3. 142GHz carrier. The performance of the frequency synthesizer meets the requirements of GPS applications very well.

High-Power Distributed Feedback Laser Diodes Emitting at 820nm

By etching a second-order grating directly into the Al-free optical waveguide region of a ridgewaveguide（RW） AlGaInAs/AlGaAs distributed feedback（DFB） laser diode,a front facet output power of 30mW is obtained at about 820nm with a single longitudinal mode. The Al-free grating surface permits the re-growth of a high-quality cladding layer that yields excellent device performance. The threshold current of these laser diodes is 57mA,and the slope efficiency is about 0.32mW/mA.

Power law behavior of the isotope yield distributions in the multifragmentation regime of heavy ion reactions

Isotope yield distributions in the multifragmentation regime were studied with high-quality isotope identification, focusing on the intermediate mass fragments (IMFs) produced in semiviolent collisions. The yields were analyzed within the framework of a modified Fisher model. Using the ratio of the mass-dependent symmetry energy coefficient relative to the temperature, a(sym)/T, extracted in previous work and that of the pairing term, a(p)/T, extracted from this work, and assuming that both reflect secondary decay processes, the experimentally observed isotope yields were corrected for these effects. For a given I = N - Z value, the corrected yields of isotopes relative to the yield of C-12 show a power law distribution Y (N, Z)/Y(C-12) similar to A(-tau) in the mass range 1 <= A <= 30, and the distributions are almost identical for the different reactions studied. The observed power law distributions change systematically when I of the isotopes changes and the extracted tau value decreases from 3.9 to 1.0 as I increases from -1 to 3. These observations are well reproduced by a simple deexcitation model, with which the power law distribution of the primary isotopes is determined to be tau(prim) = 2.4 +/- 0.2, suggesting that the disassembling system at the time of the fragment formation is indeed at, or very near, the critical point.

Process control in agile supply chain network.

The work comprises a new theoretical development applied to aid decision making in an increasingly important commercial sector. Agile supply, where small volumes of high margin, short life cycle innovative products are offered, is increasingly carried out through a complex global supply chain network. We outline an equilibrium solution in such a supply chain network, which works through limited cooperation and coordination along edges (links) in the network. The links constitute the stochastic modelling entities rather than the nodes of the network. We utilise newly developed phase plane analysis to identify, model and predict characteristic behaviour in supply chain networks. The phase plane charts profile the flow of inventory and identify out of control conditions. They maintain quality within the network, as well as intelligently track the way the network evolves in conditions of changing variability. The methodology is essentially distribution free, relying as it does on the study of forecasting errors, and can be used to examine contractual details as well as strategic and game theoretical concepts between decision-making components (agents) of a network. We illustrate with typical data drawn from supply chain agile fashion products.

The Quality of Democracy in Belarus and Ukraine

Korosteleva-Polglase, Elena, 'The Quality of Democracy in Belarus and Ukraine', The Journal of Communist Studies and Transition Politics, (2004) 20 (1), pp. 122-142(21) Special Issue: The Quality of Democracy in Post-Communist Europe RAE2008

Business service quality in an e-commerce environment

Yang, Y., Humphreys, P., & McIvor, R. (2006). Business service quality in an e-commerce environment. Supply Chain Management: An International Journal, 11 (3), 195-201. RAE2008

An energy efficient power controller switching methodology for an ambient healthcare network

A methodology for improved power controller switching in mobile Body Area Networks operating within the ambient healthcare environment is proposed. The work extends Anti-windup and Bumpless transfer results to provide a solution to the ambulatory networking problem that ensures sufficient biometric data can always be regenerated at the base station. The solution thereby guarantees satisfactory quality of service for healthcare providers. Compensation is provided for the nonlinear hardware constraints that are a typical feature of the type of network under consideration and graceful performance degradation in the face of hardware output power saturation is demonstrated, thus conserving network energy in an optimal fashion.

Grid integration of wave energy & generic modelling of ocean devices for power system studies

The work presented in this thesis covers four major topics of research related to the grid integration of wave energy. More specifically, the grid impact of a wave farm on the power quality of its local network is investigated. Two estimation methods were developed regarding the flicker level Pst generated by a wave farm in relation to its rated power as well as in relation to the impedance angle ψk of the node in the grid to which it is connected. The electrical design of a typical wave farm design is also studied in terms of minimum rating for three types of costly pieces of equipment, namely the VAr compensator, the submarine cables and the overhead line. The power losses dissipated within the farm's electrical network are also evaluated. The feasibility of transforming a test site into a commercial site of greater rated power is investigated from the perspective of power quality and of cables and overhead line thermal loading. Finally, the generic modelling of ocean devices, referring here to both wave and tidal current devices, is investigated.

The quality of diabetes care in the community: practice, policy and culture

Aim: Diabetes is an important barometer of health system performance. This chronic condition is a source of significant morbidity, premature mortality and a major contributor to health care costs. There is an increasing focus internationally, and more recently nationally, on system, practice and professional-level initiatives to promote the quality of care. The aim of this thesis was to investigate the ‘quality chasm’ around the organisation and delivery of diabetes care in general practice, to explore GPs’ attitudes to engaging in quality improvement activities and to examine efforts to improve the quality of diabetes care in Ireland from practice to policy. Methods: Quantitative and qualitative methods were used. As part of a mixed methods sequential design, a postal survey of 600 GPs was conducted to assess the organization of care. This was followed by an in-depth qualitative study using semi-structured interviews with a purposive sample of 31 GPs from urban and rural areas. The qualitative methodology was also used to examine GPs’ attitudes to engaging in quality improvement. Data were analysed using a Framework approach. A 2nd observation study was used to assess the quality of care in 63 practices with a special interest in diabetes. Data on 3010 adults with Type 2 diabetes from 3 primary care initiatives were analysed and the results were benchmarked against national guidelines and standards of care in the UK. The final study was an instrumental case study of policy formulation. Semi-structured interviews were conducted with 15 members of the Expert Advisory Group (EAG) for Diabetes. Thematic analysis was applied to the data using 3 theories of the policy process as analytical tools. Results: The survey response rate was 44% (n=262). Results suggested care delivery was largely unstructured; 45% of GPs had a diabetes register (n=157), 53% reported using guidelines (n=140), 30% had formal call recall system (n=78) and 24% had none of these organizational features (n=62). Only 10% of GPs had a formal shared protocol with the local hospital specialist diabetes team (n=26). The lack of coordination between settings was identified as a major barrier to providing optimal care leading to waiting times, overburdened hospitals and avoidable duplication. The lack of remuneration for chronic disease management had a ripple effect also creating costs for patients and apathy among GPs. There was also a sense of inertia around quality improvement activities particularly at a national level. This attitude was strongly influenced by previous experiences of change in the health system. In contrast GP’s spoke positively about change at a local level which was facilitated by a practice ethos, leadership and special interest in diabetes. The 2nd quantitative study found that practices with a special interest in diabetes achieved a standard of care comparable to the UK in terms of the recording of clinical processes of care and the achievement of clinical targets; 35% of patients reached the HbA1c target of <6.5% compared to 26% in England and Wales. With regard to diabetes policy formulation, the evolving process of action and inaction was best described by the Multiple Streams Theory. Within the EAG, the formulation of recommendations was facilitated by overarching agreement on the “obvious” priorities while the details of proposals were influenced by personal preferences and local capacity. In contrast the national decision-making process was protracted and ambiguous. The lack of impetus from senior management coupled with the lack of power conferred on the EAG impeded progress. Conclusions: The findings highlight the inconsistency of diabetes care in Ireland. The main barriers to optimal diabetes management center on the organization and coordination of care at the systems level with consequences for practice, providers and patients. Quality improvement initiatives need to stimulate a sense of ownership and interest among frontline service providers to address the local sense of inertia to national change. To date quality improvement in diabetes care has been largely dependent the “special interest” of professionals. The challenge for the Irish health system is to embed this activity as part of routine practice, professional responsibility and the underlying health care culture.

Exploring alternatives for milk quality improvement and more efficient dairy production in a smallholder farming context – case study: Mantaro Valley (Peru)

Consumer demand is revolutionizing the way products are being produced, distributed and marketed. In relation to the dairy sector in developing countries, aspects of milk quality are receiving more attention from both society and the government. However, milk quality management needs to be better addressed in dairy production systems to guarantee the access of stakeholders, mainly small-holders, into dairy markets. The present study is focused on an analysis of the interaction of the upstream part of the dairy supply chain (farmers and dairies) in the Mantaro Valley (Peruvian central Andes), in order to understand possible constraints both stakeholders face implementing milk quality controls and practices; and evaluate “ex-ante” how different strategies suggested to improve milk quality could affect farmers and processors’ profits. The analysis is based on three complementary field studies conducted between 2012 and 2013. Our work has shown that the presence of a dual supply chain combining both formal and informal markets has a direct impact on dairy production at the technical and organizational levels, affecting small formal dairy processors’ possibilities to implement contracts, including agreements on milk quality standards. The analysis of milk quality management from farms to dairy plants highlighted the poor hygiene in the study area, even when average values of milk composition were usually high. Some husbandry practices evaluated at farm level demonstrated cost effectiveness and a big impact on hygienic quality; however, regular application of these practices was limited, since small-scale farmers do not receive a bonus for producing hygienic milk. On the basis of these two results, we co-designed with formal small-scale dairy processors a simulation tool to show prospective scenarios, in which they could select their best product portfolio but also design milk payment systems to reward farmers’ with high milk quality performances. This type of approach allowed dairy processors to realize the importance of including milk quality management in their collection and manufacturing processes, especially in a context of high competition for milk supply. We concluded that the improvement of milk quality in a smallholder farming context requires a more coordinated effort among stakeholders. Successful implementation of strategies will depend on the willingness of small-scale dairy processors to reward farmers producing high milk quality; but also on the support from the State to provide incentives to the stakeholders in the formal sector.

Pittsburgh air quality study overview

Ambient sampling for the Pittsburgh Air Quality Study (PAQS) was conducted from July 2001 to September 2002. The study was designed (1) to characterize particulate matter (PM) by examination of size, surface area, and volume distribution, chemical composition as a function of size and on a single particle basis, morphology, and temporal and spatial variability in the Pittsburgh region; (2) to quantify the impact of the various sources (transportation, power plants, biogenic sources, etc.) on the aerosol concentrations in the area; and (3) to develop and evaluate the next generation of atmospheric aerosol monitoring and modeling techniques. The PAQS objectives, study design, site descriptions and routine and intensive measurements are presented. Special study days are highlighted, including those associated with elevated concentrations of daily average PM2.5 mass. Monthly average and diurnal patterns in aerosol number concentration, and aerosol nitrate, sulfate, elemental carbon, and organic carbon concentrations, light scattering as well as gas-phase ozone, nitrogen oxides, and carbon monoxide are discussed with emphasis on the processes affecting them. Preliminary findings reveal day-to-day variability in aerosol mass and composition, but consistencies in seasonal average diurnal profiles and concentrations. For example, the seasonal average variations in the diurnal PM2.5 mass were predominately driven by the sulfate component. © 2004 Elsevier Ltd. All rights reserved.