Analysis, improvement, and development of new firmware for the smart citizen kit ambient board

The objective of this project was to develop firmware for both the Arduino-compatible boards of the Smart Citizen initiative, and for the RTX4100 low-power WiFi.

Predicting overall service quality: a structural equation modelling approach

In this article, the results of a modified SERVQUAL questionnaire (Parasuraman et al., 1991) are reported. The modifications consisted in substituting questionnaire items particularly suited to a specific service (banking) and context (county of Girona, Spain) for the original rather general and abstract items. These modifications led to more interpretable factors which accounted for a higher percentage of item variance. The data were submitted to various structural equation models which made it possible to conclude that the questionnaire contains items with a high measurement quality with respect to five identified dimensions of service quality which differ from those specified by Parasuraman et al. And are specific to the banking service. The two dimensions relating to the behaviour of employees have the greatest predictive power on overall quality and satisfaction ratings, which enables managers to use a low-cost reduced version of the questionnaire to monitor quality on a regular basis. It was also found that satisfaction and overall quality were perfectly correlated thus showing that customers do not perceive these concepts as being distinct

Creating dynamic continuous improvement system for Larox Corporation

Today´s organizations must have the ability to react to rapid changes in the market. These rapid changes cause pressure to continuously find new efficient ways to organize work practices. Increased competition requires businesses to become more effective and to pay attention to quality of management and to make people to understand their work's impact on the final result. The fundamentals in continmuois improvement are systematic and agile tackling of indentified individual process constraints and the fact tha nothin finally improves without changes. Successful continuous improvement requires management commitment, education, implementation, measurement, recognition and regeneration. These ingredients form the foundation, both for breakthrough projects and small step ongoing improvement activities. One part of the organization's management system are the quality tools, which provide systematic methodologies for identifying problems, defining their root causes, finding solutions, gathering and sorting of data, supporting decision making and implementing the changes, and many other management tasks. Organizational change management includes processes and tools for managing the people in an organizational level change. These tools include a structured approach, which can be used for effective transition of organizations through change. When combined with the understanding of change management of individuals, these tools provide a framework for managing people in change,

Validation of an instrument to evaluate quality of life in the aging population: WHOQOL-AGE.

BACKGROUND: There is a need for short, specific instruments that assess quality of life (QOL) adequately in the older adult population. The aims of the present study were to obtain evidence on the validity of the inferences that could be drawn from an instrument to measure QOL in the aging population (people 50+ years old), and to test its psychometric properties. METHODS: The instrument, WHOQOL-AGE, comprised 13 positive items, assessed on a five-point rating scale, and was administered to nationally representative samples (n = 9987) from Finland, Poland, and Spain. Cronbach's alpha was employed to assess internal consistency reliability, whereas the validity of the questionnaire was assessed by means of factor analysis, graded response model, Pearson's correlation coefficient and unpaired t-test. Normative values were calculated across countries and for different age groups. RESULTS: The satisfactory goodness-of-fit indices confirmed that the factorial structure of WHOQOL-AGE comprises two first-order factors. Cronbach's alpha was 0.88 for factor 1, and 0.84 for factor 2. Evidence supporting a global score was found with a second-order factor model, according to the goodness-of-fit indices: CFI = 0.93, TLI = 0.91, RMSEA = 0.073. Convergent validity was estimated at r = 0.75 and adequate discriminant validity was also found. Significant differences were found between healthy individuals (74.19 ± 13.21) and individuals with at least one chronic condition (64.29 ± 16.29), supporting adequate known-groups validity. CONCLUSIONS: WHOQOL-AGE has shown good psychometric properties in Finland, Poland, and Spain. Therefore, considerable support is provided to using the WHOQOL-AGE to measure QOL in older adults in these countries, and to compare the QOL of older and younger adults.

Control methods for arc welding power supplies

Welding is one of the most important process of modern industry. Welding technology is used in the manufacture and repair a wide variety of products from different metals and alloys. In this thesis the different aspects of arc welding were discussed, such as stability and control of welding arc, power supplies for arc welding (especially the welding inverters because it is the most modern welding power source). All parameters of power source have influence on the arc parameters and its by-turn influence on quality. The ways of control for arc welding inverter power sources have been considered. Calculations and modeling in Matlab/Simulink were done for PI control method. All parameters of power source have influence on the arc parameters and its by-turn influence on quality.

Optimization of the power cable for low voltage direct current system

The demand for electricity is constantly growing in contemporary world and, in the same time, quality and reliability requirements are becoming more rigid. In addition, renewable sources of energy have been widely introduced for power generation, and they create specific challenges for the network. Consequently, new solution for distribution system is required, and Low Voltage Direct Current (LVDC) system is the proposed one. This thesis focuses on the investigation of specific cable features for low voltage direct current (LVDC) distribution system. The LVDC system is public ±750 VDC distribution system, which is currently being developed at Lappeen-ranta University of Technology. The aspects, considered in the thesis, are reliable and economic power transmission in distribution networks and possible power line communication in the LVDC cable.

Voimalaitoksen palamisilman esilämmittimen sisäpuolisen korroosion hallinta pinta-aktiivisten amiinien avulla

Useat voimalaitokset käyttävät hiiliteräksistä valmistettuja palamisilman esilämmittimiä, joissa höyrykattilan palamisilmaa lämmitetään matalapainehöyryllä. Joissakin tapauksissa esilämmittimet ovat kärsineet sisäpuolisen korroosion aiheuttamista putkirikoista. Tämän työn tavoitteena oli selvittää korroosiovaurioiden aiheuttajat ja tarkastella eri keinoja uusien korroosiovaurioiden ehkäisemiseksi. Keskeisimpänä uusien vaurioiden ehkäisykeinona tarkastellaan pinta-aktiivisia amiineja sisältäviä höyrykattilan jälkiannostelukemikaaliseoksia, joista tarkemman tarkastelun kohteena on kaupallinen Helamin 90 H Turb- kemikaaliseos. Pääasialliseksi korroosion aiheuttajaksi on usein epäilty höyryn sisältämää hiilidioksidia. Uusimpien näkemysten mukaan orgaaniset hapot, pääasiassa etikka- ja muurahaishappo ovat kuitenkin hiilidioksidia voimakkaampia korroosion aiheuttajia ilmanesilämmittimissä. Orgaaniset hapot väkevöityvät höyryn lauhtumisen alkaessa muodostuviin lauhdepisaroihin ja alentavat pH-tasoa radikaalisti. pH-tason aleneminen nopeuttaa metallipintoja suojaavan magnetiitin liukenemista ja vaikeuttaa myös sen uusiutumista. Orgaanisia happoja ja hiilidioksidia muodostuu orgaanisten aineiden osittaisessa hajoamisessa höyrykattilan vesi-höyrypiirissä. Pääasialliset orgaanisten aineiden lähteet ovat lisäveden mukana kattilaan kulkeutuva luonnon orgaaninen aines ja käytetyt orgaaniset jälkiannostelukemikaalit. Orgaanisten aineiden kuormaa voidaan pienentää parantamalla lisäveden valmistusprosessin orgaanisten aineiden erotustehokkuutta esimerkiksi käänteisosmoosilla. Mikäli lisäveden laadun parantaminen ei ole järkevästi toteutettavissa, voidaan orgaanisten jälkiannostelukemikaalien oikeanlaisella käytöllä neutraloida orgaanisten happojen vaikutus ilmanesilämmittimissä. Tehokkaimmaksi korroosion hillitsijäksi suoritettujen mittausten perusteella osoittautuivat kemikaaliseokset, jotka sisältävät alkaloivien amiinien lisäksi kalvoa muodostavaa pinta-aktiivista amiinia.

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

Assessment of hydrochemical quality of ground water under some urban areas within sana'a secreteriat

Groundwater from nine wells of three different districts, located at Sana'a secretariat was analyzed for hydrochemical quality assessment. Measurements of water quality parameters including pH, EC, CO3(2-), HCO3-, Cl-, NO3-, SO4(2-), Ca2+, Mg2+, Fe3+, K+, and Na+ were carried out . Classification of the groundwater samples according to Cl, SO4(2-), CO3(2-) and HCO3-, hardness (H), total dissolved solids (TDS), base-exchange, and meteoric genesis was demonstrated. Suitability of ground water samples for irrigation and industrial uses according to sodium adsorption ration (SAR), ratio of dissolved sodium (RDS), residual sodium carbonate (RSC) and saturation index (SI) was also investigated. The results of this study showed that almost all ground water samples were of good quality that makes them suitable for drinking and domestic uses. Results also indicated that even though some of the ground water samples were suitable for irrigation purposes, almost all of them were found not be good for industrial uses. Despite all drawbacks of the sewerage system built around Sana'a secretariat at the beginning of the first decade of the third millennium, the results of this study indicate that there is scope of significant improvement in Sana'a secretariat ground water quality.

Improvement of Surface Strength of Paper

Offset printing is a popular printing method that is especially suitable for large and fast print jobs. Newspapers, magazines and books are typical examples of products printed with offset method. In high volume printing production high efficiency is essential. Offset printing uses tacky inks that cause serious stress to the paper surface. Dusting and linting are terms that describe how loose and weakly bonded particles are removed from the paper surface in the printing process. The removed particles accumulate in the process causing deteriorating print quality. This forces the printing operators to stop production for washing and cleaning. Time and money are lost. Dusting and linting tendency of paper can be decreased by improving the surface strength of paper. In the present work a method to increase the surface strength of paper was studied. In the literature part offset printing method and challenges related to offset printing are presented. A review of new methods for surface sizing of paper is also presented. The experimental part presents trials where an apparatus for improving paper surface strength was tested and developed in mill scale. Laboratory work supporting the actual mill scale operations is also presented. The acquired results provide a solid base of information to make decisions on how to proceed with research in the present field of study.

Requirement management in nuclear power projects

Diplomityön tarkoituksena oli tutkia vaatimusten hallintaa suunnittelu- ja konsultointiyrityksen kannalta Suomen ydinvoimaprojekteissa keskittyen ydinturvallisuus- ja laatuvaatimuksiin. Ydinvoimaprojekteissa toimiminen on edellyttänyt menettelyohjeiden ja laatujärjestelmän uudelleen organisointia yrityksessä ja esiin on noussut haasteita liittyen muun muassa vaatimusten tunnistamiseen ja todentamiseen erityyppisissä ja erilaajuisissa projekteissa. Työ toteutettiin perehtymällä ydinvoimaan liittyvään lainsäädäntöön Suomessa, ohjeisiin ja standardeihin sekä haastattelemalla yrityksen omia asiantuntijoita. Viimeaikaisista sekä meneillään olevista projekteista kerättiin kokemuksia sekä arvioitiin ydinvoima projekteja varten laaditun projektin toteutusohjeen toimivuutta ja käytettävyyttä esimerkkiprojektin avulla. Suurimmiksi haasteiksi tunnistettiin lainsäädännöllisten vaatimusten, kuten ydinvoima- laitosohjeiden (YVL) muuttuminen ja tulkinnanvaraisuus sekä asiakkaiden perehtymät- tömyys Suomen lainsäädäntöön ja vaatimustasoon liittyen ydinturvallisuuteen. Työn tuloksena tunnistettiin hyviä vaatimusten hallintaan liittyviä projektinhallintaa ja ydin- turvallisuutta edistäviä asioita, kuten vaatimusten täsmentäminen jo sopimustasolla sekä niiden täyttymisen seuranta projektin aikana. Erillisen vaatimustietokannan luomista ydinvoimaprojekteja varten tutkittiin, mutta siitä luovuttiin teknisten vaatimusten osalta kannattamattomana, sillä standardien ja vaatimusten määrä kasvoi niin suureksi, että niiden hallitseminen vaatisi enemmän työtä kuin mitä projektien taso yleensä sallisi.

Process approach in quality management - Case: ECO process development in EMS industry

The aim of the thesis was to study quality management with process approach and to find out how to utilize process management to improve quality. The operating environment of organizations has changed. Organizations are focusing on their core competences and networking with suppliers and customers to ensure more effective and efficient value creation for the end customer. Quality management is moving from inspection of the output to prevention of problems from occurring in the first place and management thinking is changing from functional approach to process approach. In the theoretical part of the thesis, it is studied how to define quality, how to achieve good quality, how to improve quality, and how to make sure the improvement goes on as never ending cycle. A selection of quality tools is introduced. Process approach to quality management is described and compared to functional approach, which is the traditional way to manage operations and quality. The customer focus is also studied, and it is presented, that to ensure long term customer commitment, organization needs to react to changing customer requirements and wishes by constantly improving the processes. In the experimental part the theories are tested in a process improvement business case. It is shown how to execute a process improvement project starting from defining the customer requirements, continuing to defining the process ownership, roles and responsibilities, boundaries, interfaces and the actual process activities. The control points and measures are determined for the process, as well as the feedback and corrective action process, to ensure continual improvement can be achieved and to enable verification that customer requirements are fulfilled.

Impact of bariatric surgery on depression and anxiety symptons, bulimic behaviors and quality of life

OBJECTIVE: To assess psychiatric symptoms, substance use, quality of life and eating behavior of patients undergoing bariatric surgery before and after the procedure.METHODS: We conducted a prospective longitudinal study of 32 women undergoing bariatric surgery. To obtain data, the patients answered specific, self-administered questionnaires.RESULTS: We observed a reduction in depressive and anxious symptoms and also in bulimic behavior, as well as an improved quality of life in the physical, psychological and environmental domains. There was also a decrease in use of antidepressants and appetite suppressants, but the surgery was not a cessation factor in smoking and / or alcoholism.CONCLUSION: a decrease in psychiatric symptoms was observed after bariatric surgery, as well as the reduction in the use of psychoactive substances. In addition, there was an improvement in quality of life after surgical treatment of obesity.

Configuration management process improvement : a case study of a Pan-Nordic insurance company

Configuration management is often seen as an enabler for the main IT Service Management (ITSM) processes such as Incident and Problem management. A decent level of quality of IT configuration data is required in order to carry out routines of these processes. This case study examines the state of configuration management in a multinational organization and aims at identification of methods for its improvement. The author has stayed five months with this company in order to collect different sources of evidence and to make observations. The main source of data for this study is interviews with some of the key employees of the assigned organization who are involved into the ITSM processes. This study concludes the maturity level of the existing configuration management process to be repeatable but intuitive, and outlines the principal requirements for its improvement. A match between the requirements identified in the organization and the requirements stated in the ISO/IEC 20000 standard indicates the possibility of adopting ITIL guidelines as a method for configuration management process improvement. The outcome of the study presents a set of recommendations for improvement that considers the process, the information model and the information system for configuration management in the case organization.

Understanding and improving quality of secondary school education : conceptions among teachers in Tanzania

Temat för studien handlar om gymnasielärares uppfattningar om kvalitet och om hur kvalitet kan utvecklas i gymnasieutbildningen in Tanzania. Studien är till sin karaktär kvalitativ och består av utprövade semistrukturerade intervjuer med sammanlagt trettio lärare som arbetar i fyra gymnasieskolor både i urbana och rurala miljöer. Lärarna har varierande arbetserfarenhet och undervisar i olika ämnen. Huvudfokus har gällt identifieringen av variationer i lärares uppfattningar om kvalitet. På basen av två forskningsfrågor avslöjar analysen uppfattningar av hur lärare förstår och önskar utveckla kvaliteten på gymnasieutbildningen. Resultaten visar att lärare förstår kvaliteten på utbildningen i sina skolor som försök att möta skolans och samhällets mål, som individuella prestationer och förmågor som att inneha kompetenser och som att möta utmaningar inom utbildning, Identifierade uppfattningar var baserade på lärarnas personliga kunskap, arbetsmiljön och varierande omständigheter som rådde i deras skolor. Uppfattningar om en förbättring av kvaliteten i gymnasieutbildningen innefattade utveckling av lärares motivation, skolmiljön, arbetet i klassrum, kvaliteten på lärares kunskaper och färdigheter och undervisningsmaterial. Ambitionen bakom studien ar att erbjuda en plattform för strategier för att förbättra kvaliteten på gymnasieutbildningen. Resultaten strävar till att ge en fördjupad insikt i uppfattningar hos en utvald grupp av lärare som arbetar under samma villkor inom gymnasieskolor I Tanzania. Av den här anledningen är den genererade kunskapen därför relevant för att belysa lärares uppfattningar även utanför den studerade gruppen av respondenter.