Fault detection in rotating machines by vibration signal processing techniques

Machines with moving parts give rise to vibrations and consequently noise. The setting up and the status of each machine yield to a peculiar vibration signature. Therefore, a change in the vibration signature, due to a change in the machine state, can be used to detect incipient defects before they become critical. This is the goal of condition monitoring, in which the informations obtained from a machine signature are used in order to detect faults at an early stage. There are a large number of signal processing techniques that can be used in order to extract interesting information from a measured vibration signal. This study seeks to detect rotating machine defects using a range of techniques including synchronous time averaging, Hilbert transform-based demodulation, continuous wavelet transform, Wigner-Ville distribution and spectral correlation density function. The detection and the diagnostic capability of these techniques are discussed and compared on the basis of experimental results concerning gear tooth faults, i.e. fatigue crack at the tooth root and tooth spalls of different sizes, as well as assembly faults in diesel engine. Moreover, the sensitivity to fault severity is assessed by the application of these signal processing techniques to gear tooth faults of different sizes.

Razionalizzazione di un magazzino slow moving in una azienda metalmeccanica

ABSTRACT In passato valeva il motto “grande è meglio”. Le aziende avevano enormi magazzini che riempivano fino a che questi riuscivano a contenere merce. Ciò avveniva nella convinzione che gli alti costi della gestione delle scorte sarebbero stati superati dalle vendite. Negli ultimi anni le aziende hanno però radicalmente cambiato il loro approccio alla gestione delle rimanenze: queste, vengono considerate un eccesso e i magazzini con elevate scorte vengono visti come un‟opportunità mancata e capitale sprecato. I produttori sono sempre più consapevoli della necessità di minimizzare l‟inventario e massimizzare la rotazione dei prodotti. In questo contesto si inseriscono le problematiche connesse alla gestione delle scorte, con particolare riferimento al fenomeno dello slow moving, espressione che indica tutti i materiali a lenta movimentazione stoccati a magazzino. Questi spesso rappresentano un importante onere finanziario per le aziende: si sostengono costi di immobilizzo del capitale, di stoccaggio del materiale oltre a quelli connessi al rischio di obsolescenza. Molto spesso si tende a trascurare il problema, fino a quando le dimensioni di quest‟ultimo si ingrandiscono al punto di diventare una priorità aziendale da cui si cerca una rapida soluzione. L‟elaborato presenta un preliminare studio di caso che ha costituito il punto di partenza per la progettazione di un action plan per la riduzione e lo smaltimento degli item obsoleti e a bassa movimentazione di una realtà aziendale italiana del settore metalmeccanico di cui si presentano anche i primi risultati dell‟implementazione. Dopo aver fornito una panoramica teorica sul ruolo e la gestione delle scorte, si passa ad analizzare il problema dello slow moving in una particolare realtà aziendale, la Biffi s.r.l. di Fiorenzuola d‟Arda (Piacenza), un‟ impresa che dal 1955 produce attuatori per valvole. Esaminato il mercato di riferimento, il tipo di prodotto e il processo di fabbricazione, si passa all‟as-is del magazzino. Attraverso tale analisi, vengono poste in risalto le problematiche legate all‟identificazione, classificazione e gestione dei codici slow moving. E‟ stato proprio lo studio di questi dati che ha posto le basi per lo sviluppo dell‟action plan per la razionalizzazione delle giacenze a magazzino. Nell‟ultima parte dell‟elaborato ho quindi descritto le azioni intraprese e presentato i risultati ottenuti, che hanno consentito risparmi significativi senza effettuare investimenti , ma semplicemente utilizzando al meglio le risorse già disponibili.

Stellar Relics of the hierarchical assembly of the Galaxy

This PhD Thesis is part of a long-term wide research project, carried out by the "Osservatorio Astronomico di Bologna (INAF-OABO)", that has as primary goal the comprehension and reconstruction of formation mechanism of galaxies and their evolution history. There is now substantial evidence, both from theoretical and observational point of view, in favor of the hypothesis that the halo of our Galaxy has been at least partially, built up by the progressive accretion of small fragments, similar in nature to the present day dwarf galaxies of the Local Group. In this context, the photometric and spectroscopic study of systems which populate the halo of our Galaxy (i.e. dwarf spheroidal galaxy, tidal streams, massive globular cluster, etc) permits to discover, not only the origin and behaviour of these systems, but also the structure of our Galactic halo, combined with its formation history. In fact, the study of the population of these objects and also of their chemical compositions, age, metallicities and velocity dispersion, permit us not only an improvement in the understanding of the mechanisms that govern the Galactic formation, but also a valid indirect test for cosmological model itself. Specifically, in this Thesis we provided a complete characterization of the tidal Stream of the Sagittarius dwarf spheroidal galaxy, that is the most striking example of the process of tidal disruption and accretion of a dwarf satellite in to our Galaxy. Using Red Clump stars, extracted from the catalogue of the Sloan Digital Sky Survey (SDSS) we obtained an estimate of the distance, the depth along the line of sight and of the number density for each detected portion of the Stream (and more in general for each detected structure along our line of sight). Moreover comparing the relative number (i.e. the ratio) of Blue Horizontal Branch stars and Red Clump stars (the two features are tracers of different age/different metallicity populations) in the main body of the galaxy and in the Stream, in order to verify the presence of an age-metallicity gradient along the Stream. We also report the detection of a population of Red Clump stars probably associated with the recently discovered Bootes III stellar system. Finally, we also present the results of a survey of radial velocities over a wide region, extending from r ~ 10' out to r ~ 80' within the massive star cluster Omega Centauri. The survey was performed with FLAMES@VLT, to study the velocity dispersion profile in the outer regions of this stellar system. All the results presented in this Thesis, have already been published in refeered journals.

Synthesis and characterisation of photoreactive silanes for the self-assembly on functionalised silica surfaces

The aim of this thesis was to investigate novel techniques to create complex hierarchical chemical patterns on silica surfaces with micro to nanometer sized features. These surfaces were used for a site-selective assembly of colloidal particles and oligonucleotides. To do so, functionalised alkoxysilanes (commercial and synthesised ones) were deposited onto planar silica surfaces. The functional groups can form reversible attractive interactions with the complementary surface layers of the opposing objects that need to be assembled. These interactions determine the final location and density of the objects onto the surface. Photolithographically patterned silica surfaces were modified with commercial silanes, in order to create hydrophilic and hydrophobic regions on the surface. Assembly of hydrophobic silica particles onto these surfaces was investigated and finally, pH and charge effects on the colloidal assembly were analysed. In the second part of this thesis the concept of novel, "smart" alkoxysilanes is introduced that allows parallel surface activation and patterning in a one-step irradiation process. These novel species bear a photoreactive head-group in a protected form. Surface layers made from these molecules can be irradiated through a mask to remove the protecting group from selected regions and thus generate lateral chemical patterns of active and inert regions on the substrate. The synthesis of an azide-reactive alkoxysilane was successfully accomplished. Silanisation conditions were carefully optimised as to guarantee a smooth surface layer, without formation of micellar clusters. NMR and DLS experiments corroborated the absence of clusters when using neither water nor NaOH as catalysts during hydrolysis, but only the organic solvent itself. Upon irradiation of the azide layer, the resulting nitrene may undergo a variety of reactions depending on the irradiation conditions. Contact angle measurements demonstrated that the irradiated surfaces were more hydrophilic than the non-irradiated azide layer and therefore the formation of an amine upon irradiation was postulated. Successful photoactivation could be demonstrated using condensation patterns, which showed a change in wettability on the wafer surface upon irradiation. Colloidal deposition with COOH functionalised particles further underlined the formation of more hydrophilic species. Orthogonal photoreactive silanes are described in the third part of this thesis. The advantage of orthogonal photosensitive silanes is the possibility of having a coexistence of chemical functionalities homogeneously distributed in the same layer, by using appropriate protecting groups. For this purpose, a 3',5'-dimethoxybenzoin protected carboxylic acid silane was successfully synthesised and the kinetics of its hydrolysis and condensation in solution were analysed in order to optimise the silanisation conditions. This compound was used together with a nitroveratryl protected amino silane to obtain bicomponent surface layers. The optimum conditions for an orthogonal deprotection of surfaces modified with this two groups were determined. A 2-step deprotection process through a mask generated a complex pattern on the substrate by activating two different chemistries at different sites. This was demonstrated by colloidal adsorption and fluorescence labelling of the resulting substrates. Moreover, two different single stranded oligodeoxynucleotides were immobilised onto the two different activated areas and then hybrid captured with their respective complementary, fluorescent labelled strand. Selective hybridisation could be shown, although non-selective adsorption issues need to be resolved, making this technique attractive for possible DNA microarrays.

Self-assembly of Tetraurea Calix[4]arenes

We have elaborated a multistep strategy to synthesize ABAB-type tetraureas. There are overall nine steps but they involve very simple chemistry. The sequence starts with a 1,3-dialkylation and this is the step in which a difference between distal phenolic units is introduced. The selective ipso-nitration in the next step is based on the difference in reactivity between free phenolic units and alkylated ones. The direct reaction of tetraamino calixarene with tolylisocyanate appears not to be an appropriate method to synthesize 1,3-ditolylurea calixarenes but can be used to get tetraureas of ABBB- and AABB-types in two steps with yields of about 60%. A complete regioselective dimerization was obtained with mono-loop derivatives in which two adjacent urea residues are covalently connected. As predicted/expected the loop prevents the formation of one regioisomer, and only the dimer in which the open-chain residue slips through the loop is formed. To synthesize mono-loop tetraureas 1,2-diBoc protected tetraamino calixarene was acylated with activated di-urethanes under high dilution conditions. Di-loop compounds were synthesized by two different ways. In the reaction of tetraamine and di-urethanes the yield is about 30-40%. The second method is based on the metathesis reaction within a suitable heterodimer. For this strategy, tetraurea derivatives with residues which have terminal double bonds were prepared. The exclusive formation of the heterodimer with tetratosylurea as template is the key point in this strategy. Metathesis followed by hydrogenation give exceptionally good yields (> 80%) of the loop compounds. All the NMR data for di-loop compounds confirm that the loops prevent the interaction of the urea residues which are connected and thus, as expected, the di-loop derivatives do not form homodimers. The heterodimer between di-loop compounds and tetratolylurea (open-chain tetraureas) was the only species observed for a 1:1 mixture in benzene or chloroform. The rational synthesis of bis-[2]catenanes was a consequence of the selective formation of one regioisomer of mono-loop derivatives and the exclusive formation of heterodimers by di-loop derivatives. The formation of interlocking-ring in the synthesis of bis-[2]catenanes is an additional evidence that one open-chain residue slips through the loop in mono- or di-loop derivatives. Exceptionally good yields in the synthesis of bis-[2]catenanes are due to the high preorganization in the dimer which undergoes the metathesis. This preorganization decreases the number of the wrong connections and favors the new connections to be formed. Although the procedure for working up the reaction mixture should be still improved, these results are promising. A C2-symmetrical bis-[2]catenane was successfully resolved by column chromatography using a chiral stationary phase. Thus it should be possible to separate a larger amount to obtain pure enantiomers for further studies.

Assembly and characterization of supramolecular architectures for biosensor applications

The research has included the efforts in designing, assembling and structurally and functionally characterizing supramolecular biofunctional architectures for optical biosensing applications. In the first part of the study, a class of interfaces based on the biotin-NeutrAvidin binding matrix for the quantitative control of enzyme surface coverage and activity was developed. Genetically modified ß-lactamase was chosen as a model enzyme and attached to five different types of NeutrAvidin-functionalized chip surfaces through a biotinylated spacer. All matrices are suitable for achieving a controlled enzyme surface density. Data obtained by SPR are in excellent agreement with those derived from optical waveguide measurements. Among the various protein-binding strategies investigated in this study, it was found that stiffness and order between alkanethiol-based SAMs and PEGylated surfaces are very important. Matrix D based on a Nb2O5 coating showed a satisfactory regeneration possibility. The surface-immobilized enzymes were found to be stable and sufficiently active enough for a catalytic activity assay. Many factors, such as the steric crowding effect of surface-attached enzymes, the electrostatic interaction between the negatively charged substrate (Nitrocefin) and the polycationic PLL-g-PEG/PEG-Biotin polymer, mass transport effect, and enzyme orientation, are shown to influence the kinetic parameters of catalytic analysis. Furthermore, a home-built Surface Plasmon Resonance Spectrometer of SPR and a commercial miniature Fiber Optic Absorbance Spectrometer (FOAS), served as a combination set-up for affinity and catalytic biosensor, respectively. The parallel measurements offer the opportunity of on-line activity detection of surface attached enzymes. The immobilized enzyme does not have to be in contact with the catalytic biosensor. The SPR chip can easily be cleaned and used for recycling. Additionally, with regard to the application of FOAS, the integrated SPR technique allows for the quantitative control of the surface density of the enzyme, which is highly relevant for the enzymatic activity. Finally, the miniaturized portable FOAS devices can easily be combined as an add-on device with many other in situ interfacial detection techniques, such as optical waveguide lightmode spectroscopy (OWLS), the quartz crystal microbalance (QCM) measurements, or impedance spectroscopy (IS). Surface plasmon field-enhanced fluorescence spectroscopy (SPFS) allows for an absolute determination of intrinsic rate constants describing the true parameters that control interfacial hybridization. Thus it also allows for a study of the difference of the surface coupling influences between OMCVD gold particles and planar metal films presented in the second part. The multilayer growth process was found to proceed similarly to the way it occurs on planar metal substrates. In contrast to planar bulk metal surfaces, metal colloids exhibit a narrow UV-vis absorption band. This absorption band is observed if the incident photon frequency is resonant with the collective oscillation of the conduction electrons and is known as the localized surface plasmon resonance (LSPR). LSPR excitation results in extremely large molar extinction coefficients, which are due to a combination of both absorption and scattering. When considering metal-enhanced fluorescence we expect the absorption to cause quenching and the scattering to cause enhancement. Our further study will focus on the developing of a detection platform with larger gold particles, which will display a dominant scattering component and enhance the fluorescence signal. Furthermore, the results of sequence-specific detection of DNA hybridization based on OMCVD gold particles provide an excellent application potential for this kind of cheap, simple, and mild preparation protocol applied in this gold fabrication method. In the final chapter, SPFS was used for the in-depth characterizations of the conformational changes of commercial carboxymethyl dextran (CMD) substrate induced by pH and ionic strength variations were studied using surface plasmon resonance spectroscopy. The pH response of CMD is due to the changes in the electrostatics of the system between its protonated and deprotonated forms, while the ionic strength response is attributed from the charge screening effect of the cations that shield the charge of the carboxyl groups and prevent an efficient electrostatic repulsion. Additional studies were performed using SPFS with the aim of fluorophore labeling the carboxymethyl groups. CMD matrices showed typical pH and ionic strength responses, such as high pH and low ionic strength swelling. Furthermore, the effects of the surface charge and the crosslink density of the CMD matrix on the extent of stimuli responses were investigated. The swelling/collapse ratio decreased with decreasing surface concentration of the carboxyl groups and increasing crosslink density. The study of the CMD responses to external and internal variables will provide valuable background information for practical applications.

Tetraurea derivatives of calix[4]arenes and oligocalix[4]arenes, synthesis and self-assembly = Tetraharnstoff-Derivate von Calix[4 ]arenen und Oligocalix[4]arenen, Synthese und Selbstorganisierung

Wide rim tetraurea calix[4]arenes form hydrogen bonded dimeric capsules in apolar solvents in the presence of a suitable guest, which must be included in the cavity. The monomeric and dimeric form are never observed simultaneously under usual conditions. In general the combination of two different alkyl or aryl tetraurea derivatives results in the mixture of two homodimers and a heterodimer, however, only the heterodimeric species is observed in the 1:1 mixture of aryl and tosyl ureas. The (hetero)dimerization of oligourea calix[4]arenes (units) was used to construct larger structures via self-assembly of multiple calixarenes (building blocks) containing two (or more) covalently connected units. Among these self-assembled structures linear or branched polymers, cyclic oligomers and well-organized dendrimers were envisaged. The synthesis of the building blocks requires the preparation of calix[4]arene units possessing one (or more) functional group at the narrow or wide rim. Finally the oligourea units were covalently connected either directly or via suitable spacers within appropriate building blocks using amide bonds. Self-assembly properties of such building blocks were investigated.

Supramolecular approaches to organized luminescent nanostructures for sensing, labeling and imaging applications

The common thread of this thesis is the will of investigating properties and behavior of assemblies. Groups of objects display peculiar properties, which can be very far from the simple sum of respective components’ properties. This is truer, the smaller is inter-objects distance, i.e. the higher is their density, and the smaller is the container size. “Confinement” is in fact a key concept in many topics explored and here reported. It can be conceived as a spatial limitation, that yet gives origin to unexpected processes and phenomena based on inter-objects communication. Such phenomena eventually result in “non-linear properties”, responsible for the low predictability of large assemblies. Chapter 1 provides two insights on surface chemistry, namely (i) on a supramolecular assembly based on orthogonal forces, and (ii) on selective and sensitive fluorescent sensing in thin polymeric film. In chapters 2 to 4 confinement of molecules plays a major role. Most of the work focuses on FRET within core-shell nanoparticles, investigated both through a simulation model and through experiments. Exciting results of great applicative interest are drawn, such as a method of tuning emission wavelength at constant excitation, and a way of overcoming self-quenching processes by setting up a competitive deactivation channel. We envisage applications of these materials as labels for multiplexing analysis, and in all fields of fluorescence imaging, where brightness coupled with biocompatibility and water solubility is required. Adducts of nanoparticles and molecular photoswitches are investigated in the context of superresolution techniques for fluorescence microscopy. In chapter 5 a method is proposed to prepare a library of functionalized Pluronic F127, which gives access to a twofold “smart” nanomaterial, namely both (i)luminescent and (ii)surface-functionalized SCSSNPs. Focus shifts in chapter 6 to confinement effects in an upper size scale. Moving from nanometers to micrometers, we investigate the interplay between microparticles flowing in microchannels where a constriction affects at very long ranges structure and dynamics of the colloidal paste.

Tetrafenilciclopentadienon-derivati ed analoghi: sintesi, "self-assembly" e caratterizzazione reologica

Gels are materials that are easier to recognize than to define. For all practical purpose, a material is termed a gel if the whole volume of liquid is completely immobilized as usually tested by the ‘tube inversion’ method. Recently, supramolecular gels obtained from low molecular weight gelators (LMWGs) have attracted considerable attention in materials science since they represent a new class of smart materials sensitive to external stimuli, such as temperature, ultrasounds, light, chemical species and so on. Accordingly, during the past years a large variety of potentialities and applications of these soft materials in optoelectronics, as electronic devices, light harvesting systems and sensors, in bio-materials and in drug delivery have been reported. Spontaneous self-assembly of low molecular weight molecules is a powerful tool that allows complex supramolecular nanoscale structures to be built. The weak and non-covalent interactions such as hydrogen bonding, π–π stacking, coordination, electrostatic and van der Waals interactions are usually considered as the most important features for promoting sol-gel equilibria. However, the occurrence of gelation processes is ruled by further “external” factors, among which the temperature and the nature of the solvents that are employed are of crucial importance. For example, some gelators prefer aromatic or halogenated solvents and in some cases both the gelation temperature and the type of the solvent affect the morphologies of the final aggregation. Functionalized cyclopentadienones are fascinating systems largely employed as building blocks for the synthesis of polyphenylene derivatives. In addition, it is worth noting that structures containing π-extended conjugated chromophores with enhanced absorption properties are of current interest in the field of materials science since they can be used as “organic metals”, as semiconductors, and as emissive or absorbing layers for OLEDs or photovoltaics. The possibility to decorate the framework of such structures prompted us to study the synthesis of new hydroxy propargyl arylcyclopentadienone derivatives. Considering the ability of such systems to give π–π stacking interactions, the introduction on a polyaromatic structure of polar substituents able to generate hydrogen bonding could open the possibility to form gels, although any gelation properties has been never observed for these extensively studied systems. we have synthesized a new class of 3,4-bis (4-(3-hydroxy- propynyl) phenyl) -2, 5-diphenylcyclopentadienone derivatives, one of which (1a) proved to be, for the first time, a powerful organogelator. The experimental results indicated that the hydroxydimethylalkynyl substituents are fundamental to guarantee the gelation properties of the tetraarylcyclopentadienone unit. Combining the results of FT-IR, 1H NMR, UV-vis and fluorescence emission spectra, we believe that H-bonding and π–π interactions are the driving forces played for the gel formation. The importance of soft materials lies on their ability to respond to external stimuli, that can be also of chemical nature. In particular, high attention has been recently devoted to anion responsive properties of gels. Therefore the behaviour of organogels of 1a in toluene, ACN and MeNO2 towards the addition of 1 equivalent of various tetrabutylammonium salts were investigated. The rheological properties of gels in toluene, ACN and MeNO2 with and without the addition of Bu4N+X- salts were measured. In addition a qualitative analysis on cation recognition was performed. Finally the nature of the cyclic core of the gelator was changed in order to verify how the carbonyl group was essential to gel solvents. Until now, 4,5-diarylimidazoles have been synthesized.

Multilayer thin films by layer-by-layer (LBL) assembly of functional polyelectrolytes

Nanoscience aims at manipulating atoms, molecules and nano-size particles in a precise and controlled manner. Nano-scale control of the thin film structures of organic/polymeric materials is a prerequisite to the fabrication of sophisticated functional devices. The work presented in this thesis is a compilation of various polymer thin films with newly synthesized functional polymers. Cationic and anionic LC amphotropic polymers, p-type and n-type semiconducting polymers with triarylamine, oxadiazole, thiadiazole and triazine moieties are suitable materials to fabricate multilayers by layer-by-layer (LBL) self-assembly with a well defined internal structure. The LBL assembly is the ideal processing technique to prepare thin polymer film composites with fine control over morphology and composition at nano-scale thickness, which may have applications in photo-detectors, light-emitting diodes (LEDs), displays and sensors, as well as in solar cells. The multilayer build-up was investigated with amphotropic LC polymers individually by solution-dipping and spin-coating methods; they showed different internal orders with respect to layering and orientation of the mesogens, as a result of the liquid crystalline phase. The synthesized p-type and n-type semiconducting polymers were examined optically and electrochemically, suggesting that they are favorably promising as hole-(p-type) or electron-(n-type) transport materials in electronic and optoelectronic devices. In addition, we report a successful film deposition of polymers by the vacuum deposition method. The vapor deposition method provides a clean environment; it is solvent free and well suited to sequential depositions in hetero-structured multilayer system. As the potential applications, the fabricated polymer thin films were used as simple electrochromic films and also used as hole transporting layers in LEDs. Electrochemical and electrochromic characterizations of assembled films reveal that the newly synthesized polymers give rise to high contrast ratio and fast switching electrochromic films. The LEDs with vacuum deposited films show dramatic improvements in device characteristics, indicating that the films are promising as hole transporting layers. These are the result of not only the thin nano-scale film structures but also the combination with the high charge carrier mobility of synthesized semiconducting polymers.

Untersuchungen des Keratinfilament-Turnovers in lebenden Zellen

Das Zytoskelett eukaryotischer Zellen besteht aus drei verschiedenen Protein-Netzwerken: den Aktinfilamenten, Mikrotubuli und Intermediärfilamenten. Intermediärfilamente wurden ursprünglich als statische Strukturen angesehen, die die mechanische Stabilisierung der Zellen übernehmen. In den letzten Jahren hat sich dieses Bild jedoch geändert: Intermediärfilament-Netzwerke sind hochdynamisch und unterliegen kontinuierlichen Veränderungen, welche durch Phosphorylierungen reguliert werden. Sie interagieren mit anderen Zytoskelett-Proteinen und greifen in die Regulation von Schlüsselsignalwegen, die Zellwachstum und Zellteilung sowie Apoptose und Stressantwort bestimmen, ein. Die Mechanismen der Filamentplastizität konnten bisher jedoch nicht vollständig aufgeklärt werden. So ist beispielsweise unklar, wo Auf- und Abbau der Filamente stattfindet und welche Faktoren an der Netzwerkmodulation beteiligt sind. Ziel meiner Arbeit war es, einen Beitrag zur Aufklärung dieser Mechanismen am Beispiel der epithelialen Keratin-Intermediärfilamente zu leisten. Mit Hilfe von mikroskopischen Zeitrafferaufnahmen von fluoreszenzmarkierten Zellklonen wurden Nukleationszentren in der Zellperipherie identifiziert, in denen Keratinfilamentvorläufer gebildet werden. Es handelt sich dabei um fokale Adhäsionskomplexe, die als Anheftungsstellen zwischen der extrazellulären Matrix und dem intrazellulären Aktinfilament-System dienen. Es konnte gezeigt werden, dass diese Filamentvorläufer-Entstehung für alle untersuchten Keratinisoformen gültig ist und in epitelialen als auch nicht-epithelialen Zelltypen abläuft. Knock-Down der Adhäsionskomponente Talin verhinderte die Keratinfilamentbildung. Modulation der fokalen Adhäsionskinase, die den Auf- und Abbau der Adhäsionskomplexe koordiniert, beeinflusste ebenso die Bildung der Keratinfilamentnetzwerke. Es konnte weiterhin beobachtet werden, dass die N-terminalen Isoformen IE und IF des Zytolinkers Plectin in fokalen Adhäsionen lokalisieren und damit möglicherweise an der Vernetzung von Keratinfilamentvorläufern, Zelladhäsionen und Aktinfilamenten beteiligt sind. Letztlich stellte sich heraus, dass die Bildung der Keratinfilamentvorläufer unabhängig von Proteintranslation ist. In den mikroskopischen Zeitrafferaufnahmen wurde im Anschluss an die Keratinfilamentbildung ein kontinuierlicher zentripetaler Transport der wachsenden Vorläuferpartikel beobachtet. An Hand von pharmakologischen Experimenten konnte gezeigt werden, dass dieser Transport Aktinfilament-abhängig ist. Zeitgleich kommt es zu Partikelfusion und Integration in das periphere Netzwerk, das sich weiterhin in Richtung auf das Zellzentrum bewegt. Mit Hilfe von Photoaktivierungsversuchen und Zellfusionsexperimenten konnte die Hypothese bestätigt werden, dass der Abbau der einwandernden Keratinfilamente in lösliche, rasch diffusible Zwischenstufen den kontinuierlichen peripheren Neuaufbau ermöglicht. Aus den Beobachtungen und bereits bekannten Ergebnissen wurde ein Modell des Keratin-Zyklus entwickelt, das die folgenden Stadien umfasst: Nukleation von Keratinfilamentvorläufern an fokalen Adhäsionen in der Zellperipherie, Elongation und Fusion der Keratinfilamentvorläufer bei zeitgleichem Aktinfilament-abhängigem zentripetalen Transport, Integration der Keratinfilamentvorläufer in das periphere Netzwerk, Bündelung der Filamente, Filamentabbau in lösliche Untereinheiten und Neubeginn des Zyklus in der Zellperipherie. Eine Störung dieses Zyklus liegt bei mutierten Keratinen vor, welche die Ursache von Blasen-bildenden Hauterkrankungen sind. In der vorliegenden Arbeit wurde am Beispiel von Keratin 6a-Mutanten, welche die Hauterkrankung Pachyonychia congenita verursachen, gezeigt, dass bei diesen Keratinen die Nukleation zwar im Bereich der Adhäsionskomplexe regelrecht abläuft, die anschließende Elongation und Netzwerkbildung aber gestört ist, so dass statt dessen kurzlebige, hyperphosphorylierte Granula entstehen. Der resultierende frustrane Keratin-Zyklus in der Zellperipherie ist stark beschleunigt und kann durch p38-Inhibierung gestoppt werden. Bei Proteasomeninhibierung wird der Zyklus in Richtung der Granulabildung verschoben. In dieser Arbeit wird erstmals das Keratin-Tretmühlen-Modell vorgestellt, das den regulierbaren Auf- und Abbau-Zyklus des Keratinnetzwerks beschreibt. Damit liegen testbare Hypothesen für die Aufklärung der Keratinfilament-Plastizität in physiologischen und pathologischen Situationen vor, die nach unseren ersten Ergebnissen auch von Relevanz für andere Intermediärfilamenttypen sind.

Fluorescent ionene-dye nanoparticles by electrostatic self-assembly

It is investigated that the association of linear cationic model polyelectrolytes with oppositely charged pyrenetetrasulfonate (PY) in aqueous solution. For this purpose water soluble ionenes were prepared via Menschutkin reaction from 1-4-diazabicyclo [2.2.2] octane and e.g. 1,6-dibromohexane and 1,4 dibromotransbuten. The complex formation between dye molecules PY and oppositely charged ionenes (PD4, PD6, PD4-2 and PD4coPD6) of different chemical structures in aqueous solution was studied by light scattering (LS), small angle neutron scattering (SANS), UV-Vis, fluorescence spectroscopy and atomic force microscopy (AFM). Spectrophotometric titration results revealed that PY molecules were bind to ionenes cooperative process due to π-π interaction. Cooperative binding constant KD was determined as 6.4 x 10^6 M^-1 (+ or - 10^5 M^-1). It was found that binding mode and geometry of PY is predominantly depending on inter-charge distances of corresponding ionenes. Resultant complexes have exhibited size and structure variation as a function of charge ratio (L), ionic strength, inter-charge distances. Spherical dye-ionene complexes of which radius of gyration ranging between (RG) 50 and 190 nm have been observed in PD4-PY system while this was not possible with a different ionene (PD6) or either case ionene excess. It was found that most of the PD4-PY complexes had RG / RH ~ 0.78. Based on the AFM and LS results, spherical complexes have certain colloidal stability and their size can effectively controlled by changing the L.