Role of heat treatment in the processing and quality of oat flakes

This thesis reports on investigations into the influence of heat treatment on the manufacturing of oat flakes. Sources of variation in the oat flake quality are reviewed, including the whole chain from the farm to the consumer. The most important quality parameters of oat flakes are the absence of lipid hydrolysing enzymes, specific weight, thickness, breakage (fines), water absorption. Flavour, colour and pasting properties are also important, but were not included in the experimental part of this study. Of particular interest was the role of heat processing. The first possible heat treatment may occur already during grain drying, which in Finland generally happens at the farm. At the mill, oats are often kilned to stabilise the product by inactivating lipid hydrolysing enzymes. Almost invariably steaming is used during flaking, to soften the groats and reduce flake breakage. This thesis presents the use of a material science approach to investigating a complex system, typical of food processes. A combination of fundamental and empirical rheological measurements was used together with a laboratory scale process to simulate industrial processing. The results were verified by means of industrial trials. Industrially produced flakes at three thickness levels (nominally 0.75, 0.85 and 0.90 mm) were produced from kilned and unkilned oat groats, and the flake strength was measured at different moisture contents. Kilning was not found to significantly affect the force required to puncture a flake with a 2mm cylindrical probe, which was taken as a measure of flake strength. To further investigate how heat processing contributes to flake quality, dynamic mechanical analysis was used to characterise the effect of heat on the mechanical properties of oats. A marked stiffening of the groat, of up to about 50% increase in storage modulus, was observed during first heating at around 36 to 57°C. This was also observed in tablets prepared from ground groats and extracted oat starch. This stiffening was thus attributed to increased adhesion between starch granules. Groats were steamed in a laboratory steamer and were tempered in an oven at 80 110°C for 30 90 min. The maximum force required to compress the steamed groats to 50% strain increased from 50.7 N to 57.5 N as the tempering temperature was increased from 80 to 110°C. Tempering conditions also affected water absorption. A significantly higher moisture content was observed for kilned (18.9%) compared to unkilned (17.1%) groats, but otherwise had no effect on groat height, maximum force or final force after a 5 s relaxation time. Flakes were produced from the tempered groats using a laboratory flaking machine, using a roll gap of 0.4 mm. Apart from specific weight, flake properties were not influenced by kilning. Tempering conditions however had significant effects on the specific weight, thickness and water absorption of the flakes, as well as on the amount of fine material (<2 mm) produced during flaking. Flake strength correlated significantly with groat strength and flake thickness. Trial flaking at a commercial mill confirmed that groat temperature after tempering influenced water absorption. Variation in flake strength was observed , but at the groat temperatures required to inactivate lipase, it was rather small. Cold flaking of groats resulted in soft, floury flakes. The results presented in this thesis suggest that heating increased the adhesion between starch granules. This resulted in an increase in the stiffness and brittleness of the groat. Brittle fracture, rather than plastic flow, during flaking could result in flaws and cracks in the flake. These would be expected to increase water absorption. This was indeed observed as tempering temperature increased. Industrial trials, conducted with different groat temperatures, confirmed the main findings of the laboratory experiments. The approach used in the present study allowed the systematic study of the effect of interacting process parameters on product quality. There have been few scientific studies of oat processing, and these results can be used to understand the complex effects of process variables on flake quality. They also offer an insight into what happens as the oat groat is deformed into a flake.

Leo Baeck shaking hands with Congressman Adolph Sabath; Chicago Portraits; Groups; Men

Page 62 of the "American Jewish Cavalcade" scrapbook of Leo Baeck in New York found in ROS 10 Folder 3

The culture digitally festival of memeology: An introduction

The collection of essays set to roll out on Culture Digitally over the next month began its life as a pair of panels spanning the last two annual meetings of the International Communication Association. At the 2014 meetings in Seattle, Washington and the 2015 meetings in San Juan, Puerto Rico, various configurations of the contributors in this collection met to discuss the cultures and communicative practices associated with internet memes and viral media. Our shared goal was to bring smart people together to start to think about these digital media genres—still emerging only a few years ago and now seemingly ubiquitous—above the level of the individual example. Together, we asked questions about how internet memes and viral media might be defined, their roles in popular culture, their relationships to far older scientific and scholarly traditions, and their public implications. Two years and two discussions that ended too quickly later, we decided to write up some of our key arguments from the panels. We’ve compiled these write-ups here, in what we’ve taken to calling “The Culture Digitally Festival of Memeology.” - See more at: http://culturedigitally.org/2015/10/00-the-culture-digitally-festival-of-memeology-an-introduction-ryan-m-milner-jean-burgess/#sthash.2KzDogso.dpuf

Bayesian model comparison in cosmology with Population Monte Carlo

We use Bayesian model selection techniques to test extensions of the standard flat LambdaCDM paradigm. Dark-energy and curvature scenarios, and primordial perturbation models are considered. To that end, we calculate the Bayesian evidence in favour of each model using Population Monte Carlo (PMC), a new adaptive sampling technique which was recently applied in a cosmological context. The Bayesian evidence is immediately available from the PMC sample used for parameter estimation without further computational effort, and it comes with an associated error evaluation. Besides, it provides an unbiased estimator of the evidence after any fixed number of iterations and it is naturally parallelizable, in contrast with MCMC and nested sampling methods. By comparison with analytical predictions for simulated data, we show that our results obtained with PMC are reliable and robust. The variability in the evidence evaluation and the stability for various cases are estimated both from simulations and from data. For the cases we consider, the log-evidence is calculated with a precision of better than 0.08. Using a combined set of recent CMB, SNIa and BAO data, we find inconclusive evidence between flat LambdaCDM and simple dark-energy models. A curved Universe is moderately to strongly disfavoured with respect to a flat cosmology. Using physically well-motivated priors within the slow-roll approximation of inflation, we find a weak preference for a running spectral index. A Harrison-Zel'dovich spectrum is weakly disfavoured. With the current data, tensor modes are not detected; the large prior volume on the tensor-to-scalar ratio r results in moderate evidence in favour of r=0.

Synthesis and applications of carbon nanomaterials for energy generation and storage

The world is facing an energy crisis due to exponential population growth and limited availability of fossil fuels. Over the last 20 years, carbon, one of the most abundant materials found on earth, and its allotrope forms such as fullerenes, carbon nanotubes and graphene have been proposed as sources of energy generation and storage because of their extraordinary properties and ease of production. Various approaches for the synthesis and incorporation of carbon nanomaterials in organic photovoltaics and supercapacitors have been reviewed and discussed in this work, highlighting their benefits as compared to other materials commonly used in these devices. The use of fullerenes, carbon nanotubes and graphene in organic photovoltaics and supercapacitors is described in detail, explaining how their remarkable properties can enhance the efficiency of solar cells and energy storage in supercapacitors. Fullerenes, carbon nanotubes and graphene have all been included in solar cells with interesting results, although a number of problems are still to be overcome in order to achieve high efficiency and stability. However, the flexibility and the low cost of these materials provide the opportunity for many applications such as wearable and disposable electronics or mobile charging. The application of carbon nanotubes and graphene to supercapacitors is also discussed and reviewed in this work. Carbon nanotubes, in combination with graphene, can create a more porous film with extraordinary capacitive performance, paving the way to many practical applications from mobile phones to electric cars. In conclusion, we show that carbon nanomaterials, developed by inexpensive synthesis and process methods such as printing and roll-to-roll techniques, are ideal for the development of flexible devices for energy generation and storage – the key to the portable electronics of the future.

A quantum chemical investigation of the metal centres in cytochrome c oxidase

Quantum effects are often of key importance for the function of biological systems at molecular level. Cellular respiration, where energy is extracted from the reduction of molecular oxygen to water, is no exception. In this work, the end station of the electron transport chain in mitochondria, cytochrome c oxidase, is investigated using quantum chemical methodology. Cytochrome c oxidase contains two haems, haem a and haem a3. Haem a3, with its copper companion, CuB, is involved in the final reduction of oxygen into water. This binuclear centre receives the necessary electrons from haem a. Haem a, in turn, receives its electrons from a copper ion pair in the vicinity, called CuA. Density functional theory (DFT) has been used to clarify the charge and spin distributions of haem a, as well as changes in these during redox activity. Upon reduction, the added electron is shown to be evenly distributed over the entire haem structure, important for the accommodation of the prosthetic group within the protein. At the same time, the spin distribution of the open-shell oxidised state is more localised to the central iron. The exact spin density distribution has been disputed in the literature, however, different experiments indicating different distributions of the unpaired electron. The apparent contradiction is shown to be due to the false assumption of a unit amount of unpaired electron density; in fact, the oxidised state has about 1.3 unpaired electrons. The validity of the DFT results have been corroborated by wave function based coupled cluster calculations. Point charges, for use in classical force field based simulations, have been parameterised for the four metal centres, using a newly developed methodology. In the procedure, the subsystem for which point charges are to be obtained, is surrounded by an outer region, with the purpose of stabilising the inner region, both electronically and structurally. Finally, the possibility of vibrational promotion of the electron transfer step between haem a and a3 has been investigated. Calculating the full vibrational spectra, at DFT level, of a combined model of the two haems, revealed several normal modes that do shift electron density between the haems. The magnitude of the shift was found to be moderate, at most. The proposed mechanism could have an assisting role in the electron transfer, which still seems to be dominated by electron tunnelling.

Portrait of Samuel Mayer Ehrenberg ( 1773 - 1853 ).

This painting is in dedication " in honor of Meyer Ehrenberg by his students" as stated on a scroll held by the sitter. The scroll is dated October 7, 1820 and is followed by a list of names in two columns: (M.Ehrenberg, P.Ehrenberg, B. Ehrenberg, M.Imanuel M.Balke, B.Meier, L.Franck, M. Cohen, W.Fraenkel, M. Chohns, P.Goldschmidt, J.Lippoa, A. Nathan, M.Kramer, J.Fraenkel, M.Goldschmidt.) Ehrenberg was the founder of the first modern Jewish Day School in Germany, at Wolfenbuettel. Ehrenberg was the great-grandfather of the Jewish Theologian Franz Rosenzweig.

Schoolman family papers, undated, 1889-1994

The Schoolman Papers reflect Dr. Albert P. and Mrs. Bertha Schoolmans' staunch dedication to Jewish education, Jewish causes, and Israel. Bertha Schoolman, a lifelong member of Hadassah, assisted thousands of Israeli youth as chairman of the Youth Aliyah Committee. Her diaries, photos, scrapbooks, and correspondence record her numerous visits to Israel on which she helped set up schools, met with Israeli dignitaries, and participated in Zionist Conferences and events. The collection includes a 1936 letter from Hadassah founder, Henrietta Szold, praising Mrs. Schoolman's work as well as a letter from the father of Anne Frank, thanking Mrs. Schoolman for naming a Youth Aliyah center the "Anne Frank Haven" after his later daughter.

Hannah Ruth London papers, 1919-1990.

The collection consists primarily of research notes for Ms. London's published works on portraits, miniatures and silhouettes of American Jews. The notes contain family histories of the subjects as well as information on the artists, and are arranged both by subject and artist. The collection also contains published articles on the subject by London, and photographs and lantern slides of the artwork that have been removed to the picture collection.

Individuals on the Move : Body Condition Dependent Dispersal and Quasi-Local Competition in Metapopulations

Individual movement is very versatile and inevitable in ecology. In this thesis, I investigate two kinds of movement body condition dependent dispersal and small-range foraging movements resulting in quasi-local competition and their causes and consequences on the individual, population and metapopulation level. Body condition dependent dispersal is a widely evident but barely understood phenomenon. In nature, diverse relationships between body condition and dispersal are observed. I develop the first models that study the evolution of dispersal strategies that depend on individual body condition. In a patchy environment where patches differ in environmental conditions, individuals born in rich (e.g. nutritious) patches are on average stronger than their conspecifics that are born in poorer patches. Body condition (strength) determines competitive ability such that stronger individuals win competition with higher probability than weak individuals. Individuals compete for patches such that kin competition selects for dispersal. I determine the evolutionarily stable strategy (ESS) for different ecological scenarios. My models offer explanations for both dispersal of strong individuals and dispersal of weak individuals. Moreover, I find that within-family dispersal behaviour is not always reflected on the population level. This supports the fact that no consistent pattern is detected in data on body condition dependent dispersal. It also encourages the refining of empirical investigations. Quasi-local competition defines interactions between adjacent populations where one population negatively affects the growth of the other population. I model a metapopulation in a homogeneous environment where adults of different subpopulations compete for resources by spending part of their foraging time in the neighbouring patches, while their juveniles only feed on the resource in their natal patch. I show that spatial patterns (different population densities in the patches) are stable only if one age class depletes the resource very much but mainly the other age group depends on it.

First report of Cotton leafroll dwarf virus in Thailand using a species-specific PCR validated with isolates from Brazil

Partial virus genome sequence with high nucleotide identity to Cotton leafroll dwarf virus (CLRDV) was identified from two cotton (Gossypium hirsutum) samples from Thailand displaying typical cotton leaf roll disease symptoms. We developed and validated a PCR assay for the detection of CLRDV isolates from Thailand and Brazil.

Design challenges for electronic medication administration record systems in residential aged care facilities: A formative evaluation

Introduction Electronic medication administration record (eMAR) systems are promoted as a potential intervention to enhance medication safety in residential aged care facilities (RACFs). The purpose of this study was to conduct an in-practice evaluation of an eMAR being piloted in one Australian RACF before its roll out, and to provide recommendations for system improvements. Methods A multidisciplinary team conducted direct observations of workflow (n=34 hours) in the RACF site and the community pharmacy. Semi-structured interviews (n=5) with RACF staff and the community pharmacist were conducted to investigate their views of the eMAR system. Data were analysed using a grounded theory approach to identify challenges associated with the design of the eMAR system. Results The current eMAR system does not offer an end-to-end solution for medication management. Many steps, including prescribing by doctors and communication with the community pharmacist, are still performed manually using paper charts and fax machines. Five major challenges associated with the design of eMAR system were identified: limited interactivity; inadequate flexibility; problems related to information layout and semantics; the lack of relevant decision support; and system maintenance issues.We suggest recommendations to improve the design of the eMAR system and to optimize existing workflows. Discussion Immediate value can be achieved by improving the system interactivity, reducing inconsistencies in data entry design and offering dedicated organisational support to minimise connectivity issues. Longer-term benefits can be achieved by adding decision support features and establishing system interoperability requirements with stakeholder groups (e.g. community pharmacies) prior to system roll out. In-practice evaluations of technologies like eMAR system have great value in identifying design weaknesses which inhibit optimal system use.

Erna Proskauer Collection 1988-1996

The collection contains published materials in honor of Erna Proskauer and her career in law. Also included are speeches and correspondence pertaining to her receiving the German medal of honor, Bundesverdienstkreuz, on April 5, 1995.

Longitudinal cohort study of horse owners

This report summarises the findings of a three-year mixed methods research study designed to capture factors that influence horse owner Hendra virus (HeV) risk mitigation practices. The research project focuses on horse owners; their knowledge, attitudes, and risk mitigation practices, i.e. uptake of vaccination, property management, and biosecurity practices. A flexible research methodology enabled the tracking of core subject areas over time whilst also responding to new or evolving shifts in the HeV landscape, e.g. new HeV cases, event management, and issues arising in the vaccine roll-out. By tracking relationships within the data and engaging with stakeholders and the horse owner population, it is hoped that findings from the study will help to identify important linkages and effective strategies for communication/information and policy implementation.

Electronic Building Passport - Final Report: Project 2 National Energy Efficient Building Project Phase 2

The National Energy Efficient Building Project (NEEBP) Phase One report, published in December 2014, investigated “process issues and systemic failures” in the administration of the energy performance requirements in the National Construction Code. It found that most stakeholders believed that under-compliance with these requirements is widespread across Australia, with similar issues being reported in all states and territories. The report found that many different factors were contributing to this outcome and, as a result, many recommendations were offered that together would be expected to remedy the systemic issues reported. To follow up on this Phase 1 report, three additional projects were commissioned as part of Phase 2 of the overall NEEBP project. This Report deals with the development and piloting of an Electronic Building Passport (EBP) tool – a project undertaken jointly by pitt&sherry and a team at the Queensland University of Technology (QUT) led by Dr Wendy Miller. The other Phase 2 projects cover audits of Class 1 buildings and issues relating to building alterations and additions. The passport concept aims to provide all stakeholders with (controlled) access to the key documentation and information that they need to verify the energy performance of buildings. This trial project deals with residential buildings but in principle could apply to any building type. Nine councils were recruited to help develop and test a pilot electronic building passport tool. The participation of these councils – across all states – enabled an assessment of the extent to which these councils are currently utilising documentation; to track the compliance of residential buildings with the energy performance requirements in the National Construction Code (NCC). Overall we found that none of the participating councils are currently compiling all of the energy performance-related documentation that would demonstrate code compliance. The key reasons for this include: a major lack of clarity on precisely what documentation should be collected; cost and budget pressures; low public/stakeholder demand for the documentation; and a pragmatic judgement that non-compliance with any regulated documentation requirements represents a relatively low risk for them. Some councils reported producing documentation, such as certificates of final completion, only on demand, for example. Only three of the nine council participants reported regularly conducting compliance assessments or audits utilising this documentation and/or inspections. Overall we formed the view that documentation and information tracking processes operating within the building standards and compliance system are not working to assure compliance with the Code’s energy performance requirements. In other words the Code, and its implementation under state and territory regulatory processes, is falling short as a ‘quality assurance’ system for consumers. As a result it is likely that the new housing stock is under-performing relative to policy expectations, consuming unnecessary amounts of energy, imposing unnecessarily high energy bills on occupants, and generating unnecessary greenhouse gas emissions. At the same time, Councils noted that the demand for documentation relating to building energy performance was low. All the participant councils in the EBP pilot agreed that documentation and information processes need to work more effectively if the potential regulatory and market drivers towards energy efficient homes are to be harnessed. These findings are fully consistent with the Phase 1 NEEBP report. It was also agreed that an EBP system could potentially play an important role in improving documentation and information processes. However, only one of the participant councils indicated that they might adopt such a system on a voluntary basis. The majority felt that such a system would only be taken up if it were: - A nationally agreed system, imposed as a mandatory requirement under state or national regulation; - Capable of being used by multiple parties including councils, private certifiers, building regulators, builders and energy assessors in particular; and - Fully integrated into their existing document management systems, or at least seamlessly compatible rather than a separate, unlinked tool. Further, we note that the value of an EBP in capturing statistical information relating to the energy performance of buildings would be much greater if an EBP were adopted on a nationally consistent basis. Councils were clear that a key impediment to the take up of an EBP system is that they are facing very considerable budget and staffing challenges. They report that they are often unable to meet all community demands from the resources available to them. Therefore they are unlikely to provide resources to support the roll out of an EBP system on a voluntary basis. Overall, we conclude from this pilot that the public good would be well served if the Australian, state and territory governments continued to develop and implement an Electronic Building Passport system in a cost-efficient and effective manner. This development should occur with detailed input from building regulators, the Australian Building Codes Board (ABCB), councils and private certifiers in the first instance. This report provides a suite of recommendations (Section 7.2) designed to advance the development and guide the implementation of a national EBP system.