A systolic algorithm for hidden surface removal

With the advent of VLSI it has become possible to map parallel algorithms for compute-bound problems directly on silicon. Systolic architecture is very good candidate for VLSI implementation because of its regular and simple design, and regular communication pattern. In this paper, a systolic algorithm and corresponding systolic architecture, a linear systolic array, for the scanline-based hidden surface removal problem in three-dimensional computer graphics have been proposed. The algorithm is based on the concept of sample spans or intervals. The worst case time taken by the algorithm is O(n), n being the number of segments in a scanline. The time taken by the algorithm for a given scene depends on the scene itself, and on an average considerable improvement over the worst case behaviour is expected. A pipeline scheme for handling the I/O process has also been proposed which is suitable for VLSI implementation of the algorithm.

Characterisation of dynamic recrystallisation in nickel using processing map for hot deformation

The hot deformation behaviour of polycrystalline nickel has been characterised in the temperature range 750-1200-degrees-C and strain rate range 0.0003-100 s-1 using processing maps developed in the basis of the dynamic materials model. The efficiency of power dissipation, given by [2m/(m + 1)]. where m is the strain rate sensitivity, is plotted as a function of temperature and strain rate to obtain a processing map. A domain of dynamic recrystallisation has been identified, with a peak efficiency of 31% occurring at 925-degrees-C and 1 s-1. The published results are in agreement with the prediction of the processing map. The variations of efficiency of power dissipation with temperature and strain rate in the dynamic recrystallisation domain are identical to the corresponding variation of hot ductility. The stress-strain curves exhibited a single peak in a single peak in the dynamic recrystallisation domain, whereas multiple peaks and 'drooping' stress-strain curves were observed at lower and higher strain rates, respectively. The results are explained on the basis of a simple model which considers dynamic recrystallisation in terms of rates of interface formation (nucleation) and migration (growth). It is shown that dynamic recrystallisation in nickel is controlled by the rate of nucleation, which is slower than the rate of migration. The rate of nucleation itself depends on the process of thermal recovery by climb, which in turn depends on self-diffusion.

Constructing a Community : Myths and Realities of the Open Development Model

The open development model of software production has been characterized as the future model of knowledge production and distributed work. Open development model refers to publicly available source code ensured by an open source license, and the extensive and varied distributed participation of volunteers enabled by the Internet. Contemporary spokesmen of open source communities and academics view open source development as a new form of volunteer work activity characterized by hacker ethic and bazaar governance . The development of the Linux operating system is perhaps the best know example of such an open source project. It started as an effort by a user-developer and grew quickly into a large project with hundreds of user-developer as contributors. However, in hybrids , in which firms participate in open source projects oriented towards end-users, it seems that most users do not write code. The OpenOffice.org project, initiated by Sun Microsystems, in this study represents such a project. In addition, the Finnish public sector ICT decision-making concerning open source use is studied. The purpose is to explore the assumptions, theories and myths related to the open development model by analysing the discursive construction of the OpenOffice.org community: its developers, users and management. The qualitative study aims at shedding light on the dynamics and challenges of community construction and maintenance, and related power relations in hybrid open source, by asking two main research questions: How is the structure and membership constellation of the community, specifically the relation between developers and users linguistically constructed in hybrid open development? What characterizes Internet-mediated virtual communities and how can they be defined? How do they differ from hierarchical forms of knowledge production on one hand and from traditional volunteer communities on the other? The study utilizes sociological, psychological and anthropological concepts of community for understanding the connection between the real and the imaginary in so-called virtual open source communities. Intermediary methodological and analytical concepts are borrowed from discourse and rhetorical theories. A discursive-rhetorical approach is offered as a methodological toolkit for studying texts and writing in Internet communities. The empirical chapters approach the problem of community and its membership from four complementary points of views. The data comprises mailing list discussion, personal interviews, web page writings, email exchanges, field notes and other historical documents. The four viewpoints are: 1) the community as conceived by volunteers 2) the individual contributor s attachment to the project 3) public sector organizations as users of open source 4) the community as articulated by the community manager. I arrive at four conclusions concerning my empirical studies (1-4) and two general conclusions (5-6). 1) Sun Microsystems and OpenOffice.org Groupware volunteers failed in developing necessary and sufficient open code and open dialogue to ensure collaboration thus splitting the Groupware community into volunteers we and the firm them . 2) Instead of separating intrinsic and extrinsic motivations, I find that volunteers unique patterns of motivations are tied to changing objects and personal histories prior and during participation in the OpenOffice.org Lingucomponent project. Rather than seeing volunteers as a unified community, they can be better understood as independent entrepreneurs in search of a collaborative community . The boundaries between work and hobby are blurred and shifting, thus questioning the usefulness of the concept of volunteer . 3) The public sector ICT discourse portrays a dilemma and tension between the freedom to choose, use and develop one s desktop in the spirit of open source on one hand and the striving for better desktop control and maintenance by IT staff and user advocates, on the other. The link between the global OpenOffice.org community and the local end-user practices are weak and mediated by the problematic IT staff-(end)user relationship. 4) Authoring community can be seen as a new hybrid open source community-type of managerial practice. The ambiguous concept of community is a powerful strategic tool for orienting towards multiple real and imaginary audiences as evidenced in the global membership rhetoric. 5) The changing and contradictory discourses of this study show a change in the conceptual system and developer-user relationship of the open development model. This change is characterized as a movement from hacker ethic and bazaar governance to more professionally and strategically regulated community. 6) Community is simultaneously real and imagined, and can be characterized as a runaway community . Discursive-action can be seen as a specific type of online open source engagement. Hierarchies and structures are created through discursive acts. Key words: Open Source Software, open development model, community, motivation, discourse, rhetoric, developer, user, end-user

Requirements for information management system in agricultural contracting

Menneinä vuosikymmeninä maatalouden työt ovat ensin koneellistuneet voimakkaasti ja sittemmin mukaan on tullut automaatio. Nykyään koneiden kokoa suurentamalla ei enää saada tuottavuutta nostettua merkittävästi, vaan työn tehostaminen täytyy tehdä olemassa olevien resurssien käyttöä tehostamalla. Tässä työssä tarkastelun kohteena on ajosilppuriketju nurmisäilörehun korjuussa. Säilörehun korjuun intensiivisyys ja koneyksiköiden runsas määrä ovat työnjohdon kannalta vaativa yhdistelmä. Työn tavoitteena oli selvittää vaatimuksia maatalouden urakoinnin tueksi kehitettävälle tiedonhallintajärjestelmälle. Tutkimusta varten haastateltiin yhteensä 12 urakoitsijaa tai yhteistyötä tekevää viljelijää. Tutkimuksen perusteella urakoitsijoilla on tarvetta tietojärjestelmille.Luonnollisesti urakoinnin laajuus ja järjestelyt vaikuttavat asiaan. Tutkimuksen perusteella keskeisimpiä vaatimuksia tiedonhallinnalle ovat: • mahdollisimman laaja, yksityiskohtainen ja automaattinen tiedon keruu tehtävästä työstä • karttapohjaisuus, kuljettajien opastus kohteisiin • asiakasrekisteri, työn tilaus sähköisesti • tarjouspyyntöpohjat, hintalaskurit • luotettavuus, tiedon säilyvyys • sovellettavuus monenlaisiin töihin • yhteensopivuus muiden järjestelmien kanssa Kehitettävän järjestelmän tulisi siis tutkimuksen perusteella sisältää seuraavia osia: helppokäyttöinen suunnittelu/asiakasrekisterityökalu, toimintoja koneiden seurantaan, opastukseen ja johtamiseen, työnaikainen tiedonkeruu sekä kerätyn tiedon käsittelytoimintoja. Kaikki käyttäjät eivät kuitenkaan tarvitse kaikkia toimintoja, joten urakoitsijan on voitava valita tarvitsemansa osat ja mahdollisesti lisätä toimintoja myöhemmin. Tiukoissa taloudellisissa ja ajallisissa raameissa toimivat urakoitsijat ovat vaativia asiakkaita, joiden käyttämän tekniikan tulee olla toimivaa ja luotettavaa. Toisaalta inhimillisiä virheitä sattuu kokeneillekin, joten hyvällä tietojärjestelmällä työstä tulee helpompaa ja tehokkaampaa.

Effect of zinc content on the processing map for hot working of α brass

The hot deformation behavior of α brass with varying zinc contents in the range 3%–30% was characterized using hot compression testing in the temperature range 600–900 °C and strain rate range 0.001–100 s−1. On the basis of the flow stress data, processing maps showing the variation of the efficiency of power dissipation (given by Image where m is the strain rate sensitivity) with temperature and strain rate were obtained. α brass exhibits a domain of dynamic recrystallization (DRX) at temperatures greater than 0.85Tm and at strain rates lower than 1 s−1. The maximum efficiency of power dissipation increases with increasing zinc content and is in the range 33%–53%. The DRX domain shifts to lower strain rates for higher zinc contents and the strain rate for peak efficiency is in the range 0.0001–0.05 s−1. The results indicate that the DRX in α brass is controlled by the rate of interface formation (nucleation) which depends on the diffusion-controlled process of thermal recovery by climb.

Deformation processing map for control of microstructure in Al---4Mg alloy

The compression test flow stress data of Al-4Mg alloy at different temperatures and strain rates are analysed using a dynamic materials model which considers the workpiece material as a dissipator of power causing microstructural changes. A processing map representing the efficiency of power dissipation as a function of temperature and strain rate has been established and optimum processing conditions for the alloy are determined. The features of the map correlate well with the microstructure and mechanical properties.

Characteristics of Dynamic Recrystalization Domain in the Processing Map for Hot-Working of OFHC Coper

The constitutive flow behaviour of OFHC copper under working conditions is studied using hot compression in the temperature range 650 to 900-degrees-C and strain rate range 0.001 to 100 s-1. The variation of the efficiency of power dissipation given by [2m/(m + 1)] (where m is the strain rate sensitivity) with temperature and strain rate is represented in the form of a power dissipation map and interpreted on the basis of the Dynamic Materials Model. The map prominently exhibited a domain centered at 850-degrees-C and 100 s-1 with a peak efficiency of 35 %. On the basis of the correlation of variations of grain size, efficiency of power dissipation and hot workability with temperature, the domain is identified to represent dynamic recrystallization (DRX).

Influence of cast versus wrought microstructure on the processing map for hot working of stainless steel type AISI 304

Processing maps for hot working of as-cast and wrought stainless steels of type AISI 304 have been developed in the temperature range 600 to 1250°C and strain rate range 0.001 to 100 s−1. The domain of dynamic recrystallization (DRX) in as-cast material occurs at higher temperatures (1250°C) and lower strain rates (0.001 s−1) than in the wrought steel (1100°C and 0.01 s−1). The effect is explained in terms of enhanced nucleation rate of DRX due to the carbide, ferrite particles, stable oxides/nitrides and second-phase intermetallics in the as-cast microstructure. The DRX domain is wider in the wrought material although the peak efficiency is less (32%) than in the as-cast case (40%). The flow instability regime is not significantly affected by the initial microstructure

Influence of state of stress on the processing map for hot working of stainless steel type AISI 304L: compression vs. torsion

Processing maps for hot working of stainless steel of type AISI 304L have been developed on the basis of the flow stress data generated by compression and torsion in the temperature range 600–1200 °C and strain rate range 0.1–100 s−1. The efficiency of power dissipation given by 2m/(m+1) where m is the strain rate sensitivity is plotted as a function of temperature and strain rate to obtain a processing map, which is interpreted on the basis of the Dynamic Materials Model. The maps obtained by compression as well as torsion exhibited a domain of dynamic recrystallization with its peak efficiency occurring at 1200 °C and 0.1 s−1. These are the optimum hot-working parameters which may be obtained by either of the test techniques. The peak efficiency for the dynamic recrystallization is apparently higher (64%) than that obtained in constant-true-strain-rate compression (41%) and the difference in explained on the basis of strain rate variations occurring across the section of solid torsion bar. A region of flow instability has occurred at lower temperatures (below 1000 °C) and higher strain rates (above 1 s−1) and is wider in torsion than in compression. To achieve complete microstructure control in a component, the state of stress will have to be considered.

The Commercial Structure of Pedestrian Streets and Shopping Districts - Three Cases from Finland

Kävelykadut ovat tunnustettu tapa elävöittää keskusta-alueiden kauppaa. Aluksi moni kauppias epäilee kävelykadun tuomia muutoksia, mutta kokemus osoittaa, että kävelykadut ovat olleet menestyksekkäitä ja nostavat siellä olevien yritysten myyntiä. Jotkut yritykset eivät kuitenkin hyödy kävelykaduista, kun taas toiset hyötyvät paljon kun katu muuttuu kävelykaduksi. Tämä pro gradu -tutkielma tutkii kävelykatujen kaupallista rakennetta, jotta saataisiin selville minkätyyppiset yritykset löytyvät kävelykadulta. Tuloksia verrataan sen kaupallisen keskusvyöhykkeen kaupalliseen rakenteeseen missä kävelykatu sijaitsee. Näin saadaan selville erot kaupallisessa rakenteessa. Pro gradu tutkii myös miten tavallisia ketjuyritykset ovat kävelykaduilla ja kaupallisissa keskusvyöhykkeissä. Tutkimusaineisto koottiin kaupallisen inventoinnin avulla, joka suoritettiin kolmessa suomalaisessa kaupungissa: Tammisaaressa, Keravalla ja Porissa. Saatu aineisto luokiteltiin ja tulokset piirrettiin kartalle. Perustilastollisia menetelmiä käytettiin tulosten analysoimisessa. Tulokset eriteltiin kävelykadun, kauppakeskusten ja muiden paikkojen osalta ja luokiteltiin yleisluokkiin vähittäiskauppa, ravintola ja muu palvelu. Tulokset näyttävät, että on olemassa selkeitä eroja kun vertaa kävelykatuja ja kaupallisia keskusvyöhykkeitä. Kävelykaduilla on paljon enemmän vähittäiskauppoja, etenkin muotikauppoja, kuin muilla kaduilla. Kauppakeskuksilla on samantapainen kaupallinen rakenne kuin kävelykaduilla kun taas muilla kaduilla esiintyy vähemmän vähittäiskauppoja ja enemmän palveluyrityksiä. Ravintolat ovat melkein yhtä tavallisia koko kaupallisessa keskusvyöhykkeessä. Ketjuyritysten osalta tulokset ovat epäselviä. On olemassa osviittaa siitä, että ne ovat tavallisempia kävelykaduilla, etenkin suurissa kaupungeissa. Saatua tulosta ei ole kuitenkin tarpeeksi, jotta varmaa tietoa olisi saatu. Viimeisten 10–15 vuoden ajan Suomen kävelykadut ovat muuttuneet enemmän ravintolavaltaisiksi muiden palveluiden kustannuksella. Vähittäiskauppojen määrä on pysynyt vakaana. Suomalaiset kävelykadut eroavat kaupalliselta rakenteeltaan pohjoismaisista kävelykaduista, joilla on enemmän vähittäiskauppoja ja vähemmän palveluyrityksiä. Tapauskohtaisissa tuloksissa esiintyy paljon eroavaisuuksia. Paikalliset tekijät ovat usein voimakkaampia kuin yleiset teoriat kauppojen sijainnista kävelykaduilla. Yleisesti ottaen tulokset tukevat teoreettista viitekehystä. Tulokset antavat tarkempaa tietoa kävelykatujen ja kaupallisten keskusvyöhykkeiden kaupallisesta rakenteesta ja siitä, mitkä tekijät tähän vaikuttaa.

Jatrophanviljely ja maankäyttö Vietnamissa

Biofuels are under discussion all over the world today. There are fears that the farming of biofuel plants hurts food production and weakens the food security of the poor. On the other hand, biofuel production could lessen the green house gas emissions caused by transportation, and it could also spread the profits from fuel markets more evenly between countries. The aim of this thesis is to find out how an oil plant called jatropha curcas L., which is used for biodiesel production, can affect the sustainability of livelihoods in Vietnam from the point of view of land use. Special attention is given to the effects of jatropha farming on food production, land productivity, natural resources of livelihoods and global livelihood. Jatropha belongs to the family Euphorbiaceae, and it grows naturally in tropical and subtropical areas. It can be grown on poor soils, its seeds have high oil content, and it cannot be eaten due to its toxicity. The plant grows naturally in Vietnam, and during the past few years it has also begun to be farmed for making biodiesel. Population growth in Vietnam has slowed down, but the population's standard of living and energy consumption are still rising quickly. An interest in the international biodiesel markets has awoken following Vietnam's opening up to international trade. Jatropha diesel plays a significant part in Vietnam’s clean fuel strategy, and many companies have set up jatropha plantations to produce raw material for biodiesel. Diesel made from jatropha is planned to be used both locally and for export. This thesis uses a theoretical concept of sustainable livelihoods. According to the theory, the resources that people have shape their livelihood possibilities. Farming of jatropha affects the livelihoods of people especially through land use, as land use changes have effects on many of the livelihood resources. In addition to the written sources, the material of the thesis is based on 14 interviews in Vietnam and Finland, and on observation during a field trip to Northern Vietnam in the spring of 2008. The results of the thesis show that jatropha diesel can support the sustainability of livelihoods at different scales if it is produced with deliberation. However, positive results are only possible if decisions are made carefully and more experience is collected. The possibilities of sustainable jatropha farming depend mainly on the previous land use methods and ways of production. Farming of jatropha does not threaten food production in Vietnam if the farming plans are implemented as planned. Jatropha may take some land from cassava, but at the same time, food production can be increased if mixed farming is used on some farms. Plenty of new research information and practical experiences on jatropha farming has to be collected before results of the real sustainability of the farming are ready. Carefully considered continuation and documentation of present and future projects would help to understand the possibilities of jatropha diesel in Vietnam and elsewhere.

Processing map for hot working of as cast magnesium

The constitutive flow behaviour in hot working of as cast magnesium has been studied with the help of a processing map developed in the temperature range 300-550°C and strain rate range 0·001-100 s−1. The map, interpreted using the dynamic materials model, revealed that the material undergoes dynamic recrystallisation at 425°C and 0·3 s−1, which are the optimum parameters for hot working. Ai temperatures higher than 450°C and strain rates lower than about 0·1 s−1, wedge cracking occurs in as cast magnesium. The wedge cracking domain has a high efficiency of power dissipation (60%), whereas the dynamic recrystallisation domain has a value of 34%. At temperatures below 450°C and strain rates above 10 s−1, the material exhibits flow instability in the form of mechanical twinning. At higher temperatures and strain rates, instability is manifested by flow localisation.

Processing map for hot working of stainless steel type AISI 316L

Processing and instability maps using a dynamic materials model have been developed for stainless steel type AISI 316L in the temperature range 600-1250-degrees-C and strain rate range 0.001-100 s-1 with a view to optimising its hot workability. Stainless steel type AISI 316L undergoes dynamic recrystallisation, with a peak efficiency of 35% at 1250-degrees-C and 0.05 s-1, which are the optimum parameters for hot working this material. The material undergoes dynamic recovery at 900-degrees-C and 0.001 s-1. The increase in the dynamic recrystallisation and dynamic recovery temperatures in comparison with stainless steel type AISI 304L is attributed to the presence of a backstress caused by the molybdenum additions. These results are in general agreement with those reported elsewhere on stainless steel type 316 deformed in hot extrusion and hot torsion. At temperatures < 850-degrees-C and strain rates > 10 s-1, the material exhibits flow localisation owing to adiabatic shear band formation, whereas at higher temperatures (> 850-degrees-C) and strain rates (> 10 s-1) mechanical twinning and wavy slip bands are observed. (C) 1993 The Institute of Materials.