A controlled experiment on yarn hairiness and fabric pilling

This study focused on the hairiness of worsted wool yarns and how it affects the pilling propensity of knitted wool fabrics. Conventional worsted ring spun yarns were compared with comparable SolospunTM yarns and yarns modified with a hairiness reducing air nozzle in the winding process (JetWind). Measurements of yarn hairiness (S3) on the Zweigle G565 hairiness meter showed a reduction in the S3 value of approximately 46% was achieved using SolospunTM ring spinning attachment and a 33% reduction was achieved using the JetWind process. Interestingly, subsequent evaluation of the pilling performance of fabrics made from the SolospunTM spun yarn and JetWind modified yarn showed a half grade and full grade improvement, respectively over a similar fabric made from conventional ring spun yarns. This result suggested that a relatively large reduction in yarn hairiness was needed to achieve a moderate improvement in fabric pilling, and that the nature of yarn hairiness was also a key factor in influencing fabric pilling propensity. It is postulated that the wrapping of surface hairs by the air vortex in the JetWind process may limit the ability of those surface fibers to form fuzz and reach the critical height required for pill formation.

Pectinase production by solid fermentation from Aspergillus niger by a new prescription experiment

The Ordos Plateau in China is covered with up to 300,000 ha of peashrub (Caragana) which is the dominant natural vegetation and ideal for fodder production. To exploit peashrub fodder, it is crucially important to optimize the culture conditions, especially culture substrate to produce pectinase complex. In this study, a new prescription process was developed. The process, based on a uniform experimental design, first optimizes the solid substrate and second, after incubation, applies two different temperature treatments (30 °C for the first 30 h and 23°C for the second 42 h) in the fermentation process. A multivariate regression analysis is applied to a number of independent variables (water, wheat bran, rice dextrose, ammonium sulfate, and Tween 80) to develop a predictive model of pectinase activity. A second-degree polynomial model is developed which accounts for an excellent proportion of the explained variation (R² = 97:7%). Using unconstrained mathematical programming, an optimized substrate prescription for pectinase production is subsequently developed. The mathematical analysis revealed that the optimal formula for pectinase production from Aspergillus niger by solid fermentation under the conditions of natural aeration, natural substrate pH (about 6.5), and environmental humidity of 60% is rice dextrose 8%, wheat bran 24%, ammonium sulfate ((NH₄)₂SO₄) 6%, and water 61%. Tween 80 was found to have a negative effect on the production of pectinase in solid substrate. With this substrate prescription, pectinase produced by solid fermentation of A. niger reached 36.3 IU/(g DM). Goats fed on the pectinase complex obtain an incremental increase of 0:47 kg day^-1 during the initial 25 days of feeding, which is a very promising new feeding prospect for the local peashrub. It is concluded that the new formula may be very useful for the sustainable development of arid and semiarid pastures such as those of the Ordos Plateau.

A Pollen Chase Experiment; Examining Varying Levels of Embryonic Inbreeding Depression

A pollen chase experiment was performed upon three Costa Rican populations of Witheringia solanacea to examine the breakdown of genetically enforced self incompatibility (SI) and the extent of embryonic inbreeding depression. Self-pollen was applied in the bud, with outcross pollen applied one day later, and outcross pollinations at both intervals as a control. A variety of responses were found among the populations. BOHS readily accepted self pollen and suffered from very low inbreeding depression. Monteverde and Las Cruces both have lower fruit set with self-pollination precedence indicating that bud pollinations can overcome the self-incompatibility response and that embryonic death due to inbreeding depression causes fruit failure. The treatment:control fruit set is higher for the Las Cruces plants indicating stronger SI response Self-precedence seeds from the Las Cruces plants are likely to be outcrossed. Self-precedence seeds from Monteverde are likely selfed.

Design of electrical infrastructure at container terminal and 'net metering'

Net metering is generally a consumer-based incentive for renewable sources such as wind or solar power systems also referred to as dasiacogenerationdasia. It is still a grey area for container terminals with large electric machines, such as quay cranes, automatic stacking cranes, that can operate in the regenerative mode and export electric energy to the grid. With actual measured electrical data presented for discussion, this paper provides information for the readers to provide a better understanding of their access to net metering, ultilizing their electrical equipment capabilities and be informed for their next negotiation with the power supply company.

Power demand and energy usage of container crane - comparison between AC and DC drives

The electrical data of two quay cranes, one has a DC drive system and the other has an AC drive system, in actual working conditions at a container terminal are measured and presented in this paper. Peak demand, energy usage, power factor and power quality are examined and compared.

Mechanical behaviour of irregular fibre materials

This work investigates the effect of fibre irregularities on the mechanical behaviour of the irregular fibres using the finite element method (FEM). The first part of this work examines that the effect of fibre dimensional irregularities on the linear and non-linear tensile behaviour of the fibres, using a two-dimensional (2D) finite element models. In the linear simulation, a concept of method Young’s modulus is introduced. The method Young’s modulus, breaking load and breaking extension are affected by the magnitude and frequency of diameter variation in the fibre specimen. Fibre dimensional variation and the gauge length effect are also simulated. In the non-linear analysis, some additional information is obtained on changes in the yield and post-yield regions, which are clearly shown in the load-extension curves. Further investigation is focused on the flexural buckling behaviour of fibres with dimensional irregularities. A three-dimensional (3D) finite element model is used to simulate the buckling deformation of dimensionally irregular fibres, and the critical buckling load of the simulated fibre is calculated. Two parameters, the effective length and the average diameter within the effective length of an irregular fibre, are considered to be the key factors that influence the buckling behaviour of the fibre. An important aspect of this work is the calculation of the effective length of an irregular fibre specimen during buckling. This method has not been reported before. The third part of this work is on the combined tensile and torsional behaviour of fibres with dimensional irregularities, using a three-dimensional (3D) finite element model. Two types of fibres, polyester and wool, are simulated with sine waves of different level (magnitude) and frequency at different twist levels. For the polyester fibre, experiment verification of the simulation results has been carried out, and the results indicate the FE model is well acceptable for the simulation. The final part of this work examines the combined effect of dimensional and structural irregularities on the fibre tensile behaviour. Three-dimensional (3D) finite element models are used to simulate the cracks (transverse, longitudinal, combined transverse and longitudinal cracks) and cavities distributed in uniform fibres and fibres with 30% level of diameter variation, respectively. One of important conclusions is that under the simulated conditions, the dimensional irregularity of fibre influences the tensile behaviour of fibres more than the fibre structural irregularity. The fibre dimensional irregularity affects not only the values of the breaking load and breaking extension, but also the shape of load-extension curves. However, the fibre structural irregularity simulated in the study appears to have little effect on the shape of the load-extension curves. In addition, the effect of crack or cavity size, type and distribution on fibre tensile properties is also investigated.

Evaluation of effective material properties of composite materials using special FEM

In the present paper, a novel method using the special 2D finite element method (FEM) and the concept of equivalent homogeneous materials has been employed to evaluate the effective material properties of composites. Special 2D finite elements containing an internal defect or reinforcement have been well developed in order to greatly simplify the numerical modeling of composites. It can assure the high precision especially in the vicinity of defects or reinforcements in composite materials. Some numerical examples will be provided to demonstrate the validity and versatility of the proposed method by comparing the existing results from other literatures.

Deep drawing behaviour of ultrafine grained copper : modelling and experiment

Ultrafine grained materials produced by severe plastic deformation methods possess attractive mechanical properties such as high strength compared with traditional coarse grained counterparts and reasonable ductility. Between existing severe plastic deformation methods the Equal Channel Angular Pressing is the most promising for future industrial applications and can produce a variety of ultrafine grained microstructures in materials depending on route, temperature and number of passes during processing. Driven by a rising trend of miniaturisation of parts these materials are promising candidates for microforming processes. Considering that bi-axial deformation of sheet (foil) is the major operation in microforming, the investigation of the influence of the number of ECAP passes on the bi-axial ductility in micro deep drawing test has been examined by experiments and FE simulation in this study. The experiments have showed that high force was required for drawing of the samples processed by ECAP compare to coarse grained materials. The limit drawing ratio of ultrafine grained samples was in the range of 1.9–2.0 with ECAP pass number changing from 1 to 16, while a higher value of 2.2 was obtained for coarse grained copper. However, the notable decrease in tensile ductility with increase in strength was not as pronounced for bi-axial ductility. The FE simulation using standard isotropic hardening model and von Mises yielding criterion confirmed these findings.

Radical conservative experiment in New South Wales education

This study, written from the perspective of a parent activist, articulates the 'battle of ideas' or struggle 'around the truth' of public education in New South Wales since the conservative Greiner government came to power in 1988 and instituted the 'new right' agenda. Political control is theorised in the light of debates about hegemony, power, ideology and truth. Documents what happened in 'consultations' about educational reform between the Ministers and their appointees on on the one hand, and the public education lobby, on the other.

Sweet talking to ethnic customers : a field experiment on the links between entrepreneurial business planning, cultural sensitivity and sales growth

The purpose of this study was to test whether calculated inclusion of cultural sensitivity in a selected entrepreneurial business planning (EBP) process could increase sales growth in a test market and to explore the implications of a positive answer for the theory and practice of entrepreneurial business planning. Execution of a pretest-posttest control group experimental design measured and compared the implemented effectiveness of a planned entrepreneurial initiative based on cultural sensitivity. Though small in scale and limited in focus, the initiative qualified as an example of entrepreneurial business planning (EBP) and could be used to apply, test and extend aspects of the developing theory in this field of entrepreneurship research. Since the initiative was planned to overcome a culturally-defined impediment to business growth, it also offered opportunity to explore the specific importance of cultural variables in the context of EBP.

A planned sales-promotion was offered to a control group (receiving information in English) and a treatment group (who received the information in the language of ethnic origin). The sixty subjects had been chosen at random from a population of route-trade retailers of defined ethnic origins (Greek, Lebanese and Chinese) and randomly assigned to control and treatment groups. Monthly sales averages of the promoted product were measured before and after treatment. A Chi Square test was used to evaluate the relative proportion of the control and treatment groups who accepted the promotional offer. A two sample t-test procedure and complementary non-parametric Mann-Whitney test were performed to compare the mean sales-performance change of the two groups. Analysis showed that there was a significant increase in mean sales when the planned entrepreneurial initiative was communicated in the relevant language of origin.

The experimental results have specific practical relevance to revitalising the deteriorating route-trade segment of the Australian confectionery market through increasing the sales growth of wholesalers who are prepared to act entrepreneurially and include cultural sensitivity as an element in planning and implementation. By introducing cultural sensitivity as a necessary extension of a plan’s communications role, the results also have general theoretical implications for the developing paradigm of entrepreneurial business planning.