Dynamic QoS adaptation of inter- dependent task sets in cooperative embedded systems

Due to the growing complexity and dynamism of many embedded application domains (including consumer electronics, robotics, automotive and telecommunications), it is increasingly difficult to react to load variations and adapt the system's performance in a controlled fashion within an useful and bounded time. This is particularly noticeable when intending to benefit from the full potential of an open distributed cooperating environment, where service characteristics are not known beforehand and tasks may exhibit unrestricted QoS inter-dependencies. This paper proposes a novel anytime adaptive QoS control policy in which the online search for the best set of QoS levels is combined with each user's personal preferences on their services' adaptation behaviour. Extensive simulations demonstrate that the proposed anytime algorithms are able to quickly find a good initial solution and effectively optimise the rate at which the quality of the current solution improves as the algorithms are given more time to run, with a minimum overhead when compared against their traditional versions.

Futures of automobile industry and challenges on sustainable development and mobility

Portugal had only very few foresight exercises on the automobile sector, and the most recent one was a survey held in a project on work organisation systems in the automobile industry, its recent historical paths and the special strategies of location of companies (the WorTiS project). This involved several teams with different disciplinary backgrounds and from two Portuguese universities. The provisional main results of the first round of a Delphi survey held in Portugal on the automotive sector were already published, but a further analysis was not yet done. This foresight survey was done under the WorTiS project, developed in 2004 by IET – Research Centre on Enterprise and Work Innovation (at FCT-UNL), and financed by the Portuguese Ministry of Science and Technology. Some of this experience on foresight analysis is also been transferred to other projects, namely the WORKS project on work organisation restructuring in the knowledge society that received the support from EC and still is running. The majority of experts considered having an average of less knowledge in almost all the scenario topics presented. This means that information on the automotive industry is not spread enough among academics or experts in related fields (regional scientists, innovation economists, engineers, sociologists). Some have a good knowledge but in very specialised fields. Others have expertise on foresight, or macroeconomics, or management sciences, but feel insecure on issues related with futures of automobile sector. Nevertheless, we considered specially the topics where the experts considered themselves to have some knowledge. There were no “irrelevant” topics considered as such by the expert panel. There are also no topics that are not considered a need for co-operation. The lack of technological infrastructures was not considered as a hindered factor for the accomplishment of any scenario. The experts’ panel considered no other international competence besides US, Japan or Germany in these topics. Special focus will be made in this paper on the topic 2. Public policy and automobile industries, and more specifically on the technological and/or research policies issues, where one can specify the automobile’s role in transport policies with further implications like environment, safety, energy, mobility.

Cutting forces and wear analysis of Si3N4 diamond coated tools in high speed machining

Si3N4 tools were coated with a thin diamond film using a Hot-Filament Chemical Vapour Deposition (HFCVD) reactor, in order to machining a grey cast iron. Wear behaviour of these tools in high speed machining was the main subject of this work. Turning tests were performed with a combination of cutting speeds of 500, 700 and 900 m min−1, and feed rates of 0.1, 0.25 and 0.4 mm rot−1, remaining constant the depth of cut of 1 mm. In order to evaluate the tool behaviour during the turning tests, cutting forces were analyzed being verified a significant increase with feed rate. Diamond film removal occurred for the most severe set of cutting parameters. It was also observed the adhesion of iron and manganese from the workpiece to the tool. Tests were performed on a CNC lathe provided with a 3-axis dynamometer. Results were collected and registered by homemade software. Tool wear analysis was achieved by a Scanning Electron Microscope (SEM) provided with an X-ray Energy Dispersive Spectroscopy (EDS) system. Surface analysis was performed by a profilometer.

TiB2 nanostructured coating for GFRP injection moulds

In the injection moulding of polypropylene reinforced with hard glass fibres, die materials are commonly subjected to severe abrasive wear. In order to improve its wear resistance, an unbalanced magnetron sputtering PVD compositional monolayered coating has been produced. The film was composed by a nanostructured TiB2 monolayer. Microstructure characterization and thickness evaluation were conducted by scanning electron microscopy (SEM). Film topography and roughness were accessed by SEM and Atomic Force Microscopy (AFM). The phase analyse was investigated by X-ray diffraction (XRD), using Cu Kalpha radiation. Scratch tests were conducted in order to study the film adhesion to the substrate. Load-Displacement curves (nanoindentation analysis) allowed measuring the film hardness and Young's modulus. A ball-cratering tribometer was used to determine the micro-abrasion laboratorial wear resistance, under different tests conditions, using SiC particles in distilled water slurry. At the end of these tests, the worn surfaces were analyzed by SEM and Energy Dispersive X-ray Spectroscopy (EDS) in order to compare these results with some other coatings already tested in the same conditions. To test the practical wear resistance, 135000 injection cycles were done in a plastic injection industrial mould. Coated samples were put on the plastic feed canal, after a turbulent zone. In these tests, a 30% (wt) glass fibres reinforced polypropylene was used. Worn sample surfaces were analyzed by SEM after 45.000 and 90.000 cycles. Image analyses were made in order to evaluate the damage increases and to observe the wear mechanisms involved.

Increasing the wear resistance of molds for injection of glass fiber reinforced plastics

Abrasion by glass fibers during injection molding of fiber reinforced plastics raises new challenges to the wear performance of the molds. In the last few decades, a large number of PVD and CVD coatings have been developed with the aim of minimizing abrasion problems. In this work, two different coatings were tested in order to increase the wear resistance of the surface of a mold used for glass fiber reinforced plastics: TiAlSiN and CrN/CrCN/DLC. TiAlSiN was deposited as a graded monolayer coating while CrN/CrCN/DLC was a nanostructured coating consisting of three distinct layers. Both coatings were produced by PVD unbalanced magnetron sputtering and were characterized using scanning electron microscopy (SEM) provided with energy dispersive spectroscopy (EDS), atomic force microscopy (AFM), micro hardness (MH) and scratch test analysis. Coating morphology, thickness, roughness, chemical composition and structure, hardness and adhesion to the substrate were investigated. Wear resistance was characterized through industrial tests with coated samples and an uncoated reference sample inserted in a feed channel of a plastic injection mold working with 30 wt.% glass fiber reinforced polypropylene. Results after 45,000 injection cycles indicate that the wear resistance of the mold was increased by a factor of 25 and 58, by the TiAlSiN and CrN/CrCN/DLC coatings, respectively, over the uncoated mold steel.

Anti-Corrosion performance of a new silane coating for corrosion protection of AZ31 Magnesium alloy in Hank’s solution

Mg alloys can be used as bioresorsable metallic implants. However, the high corrosion rate of magnesium alloys has limited their biomedical applications. Although Mg ions are essential to the human body, an excess may cause undesirable health effects. Therefore, surface treatments are required to enhance the corrosion resistance of magnesium parts, decreasing its rate to biocompatible levels and allowing its safe application as bioresorbable metallic implants. The application of biocompatible silane coatings is envisaged as a suitable strategy for retarding the corrosion process of magnesium alloys. In the current work, a new glycidoxypropyltrimethoxysilane (GPTMS) based coating was tested on AZ31 magnesium substrates subjected to different surface conditioning procedures before coating deposition. The surface conditioning included a short etching with hydrofluoric acid (HF) or a dc polarisation in alkaline electrolyte. The silane coated samples were immersed in Hank's solution and the protective performance of the coating was studied through electrochemical impedance spectroscopy (EIS). The EIS data was treated by new equivalent circuit models and the results revealed that the surface conditioning process plays a key role in the effectiveness of the silane coating. The HF treated samples led to the highest impedance values and delayed the coating degradation, compared to the mechanically polished samples or to those submitted to dc polarisation.

Otimização energética na empresa Simoldes Plásticos S.A.

Mestrado em Engenharia Química - Ramo Optimização Energética na Indústria Química

Deslocalização de empresas num contexto de globalização: estudo de caso de uma empresa portuguesa

Dissertação apresentada ao Instituto Superior de Contabilidade e Administração do Porto para a obtenção do Grau de Mestre em Empreendedorismo e Internacionalização Orientador: Professor Doutor José de Freitas Santos

Desenvolvimento de um jogo de simulação do sistema de produção LEAN ferramentas: 5S, organização de layout e TPM

O Lean Thinking (Pensamento Magro) baseia-se no Sistema Toyota de Produção, também conhecido pela sigla TPS (Toyota Production System). Foi desenvolvido em ambiente fabril, em particular na indústria automóvel, por Taiichi Ohno (1988) com o principal objectivo de eliminar desperdícios. O Lean Thinking tem crescido e hoje é muito mais abrangente. Com o intuito de melhorar a aprendizagem dos conceitos e das práticas lean, têm sido desenvolvidos diversos jogos que simulam a utilização das diferentes ferramentas lean. Estes jogos têm uma vertente comercial e são especialmente dirigidos para a indústria contudo não se consegue encontrar um que consiga ser utilizado para simular individualmente as ferramentas Lean. No âmbito desta dissertação, foi desenvolvido um jogo didáctico para apoio nas aulas onde são estudadas as ferramentas Lean. As ferramentas Lean abordadas neste trabalho são: 5S, Organização de Layout e Total Productive Maintenance. O jogo desenvolvido permite introduzir as ferramentas individualmente e as simulações efectuadas possibilitam a análise das melhorias obtidas com a eliminação de desperdícios através da aplicação das diferentes ferramentas.

Projecto de execução do centro comercial Mercado da Praia: Cidade da Praia: Cabo Verde

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil

Real time mobile system for support in firefighting environments

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Graffiti nas edificações: identificação e resolução do problema

Trabalho final de Mestrado para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização em Edificações

Fiscalização da construção da ETAR do Barreira/Moita

Relatório de estágio para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações

Sistema de gestão de transporte de envios parcelares

No ambiente empresarial actual, cada vez mais competitivo e exigente, é um factor fundamental para o sucesso das empresas a sua capacidade de atingir e melhorar os níveis de satisfação exigidos pelos clientes. Para identificar as melhorias a implementar, as empresas devem ser capazes de monitorizar e controlar todas as suas actividades e processos. O acompanhamento realizado às actividades delegadas a empresas externas, como por exemplo o transporte de mercadorias, é dificultado quando os prestadores destes serviços não possuem ferramentas de apoio que disponibilizem informação necessária para o efeito. A necessidade de colmatar esta dificuldade na recolha da informação durante a distribuição de uma encomenda na empresa Caetano Parts, uma empresa de revenda de peças de substituição automóvel, levou ao desenvolvimento de uma ferramenta que permite fazer o seguimento de uma encomenda em todas as suas fases, permitindo ao responsável pelas operações acompanhar o estado da encomenda desde o instante em que a encomenda é colocada, passando pelo seu processamento dentro das instalações, até à sua entrega ao cliente. O sistema desenvolvido é composto por dois componentes, o front-end e o back-end. O front-end é composto por uma aplicação web, e por uma aplicação Android para dispositivos móveis. A aplicação web disponibiliza a gestão da base de dados, o acompanhamento do estado da encomenda e a análise das operações. A aplicação Android é disponibilizada às empresas responsáveis pelo transporte das encomendas e possibilita a actualização online da informação acerca do processo de entrega. O back-end é composto pela unidade de armazenamento e processamento da informação e encontra-se alojado num servidor com ligação à internet, disponibilizando uma interface com o serviço móvel do tipo serviço web. A concepção, desenvolvimento e descrição das funcionalidades desta ferramenta são abordadas ao longo do trabalho. Os testes realizados ao longo do desenvolvimento validaram o correcto funcionamento da ferramenta, estando pronta para a realização de um teste piloto.

Aplicação de ferramentas para melhorar o processo produtivo numa empresa do sector automóvel

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica