Conservation of Williams pear using edible coating with alginate and carrageenan

The aim of this study was to evaluate the physical and chemical parameters of Williams pear, stored at 25 ºC for 15 days, with and without edible coating. Edible coatings prepared with alginate 2% and carrageenan 0.5% were tested. The analyses carried out on the samples were: weight loss, pH, soluble solids, firmness, and color. The edible coatings were characterized in terms of mechanical properties, permeability, thickness, and opacity. The results show that the application of edible coatings with carrageenan and alginate in pears influenced physical and chemical characteristics such as weight loss, pH, total soluble solids, color, and firmness of the fruit. However, the alginate coating showed the best results on pear conservation since it had lower water vapor permeability and greater tensile strength, and therefore it can be used as a protective film on these fruits.

Functionalisation of spruce O-acetyl-galactoglucomannans for barrier and composite applications

The increasing use of energy, food, and materials by the growing population in the world is leading to the situation where alternative solutions from renewable carbon resources are sought after. The growing use of plastics depends on the raw-oil production while oil refining are politically governed and required for the polymer manufacturing is not sustainable in terms of carbon footprint. The amount of packaging is also increasing. Packaging is not only utilising cardboard and paper, but also plastics. The synthetic petroleum-derived plastics and inner-coatings in food packaging can be substituted with polymeric material from the renewable resources. The trees in Finnish forests constitute a huge resource, which ought to be utilised more effectively than it is today. One underutilised component of the forests is the wood-derived hemicelluloses, although Spruce Oacetyl-galactoglucomannans (GGMs) have previously shown high potential for material applications and can be recovered in large scale. Hemicelluloses are hydrophilic in their native state, which restrains the use of them for food packaging as non-dry item. To cope with this challenge, we intended to make GGMs more hydrophobic or amphiphilic by chemical grafting and consequently with the focus of using them for barrier applications. Methods of esterification with anhydrides and cationic etherification with a trimethyl ammonium moiety were established. A method of controlled synthesis to obtain the desired properties by the means of altering temperature, reaction time, the quantity of the reagent, and even the solvent for purification of the products was developed. Numerous analytical tools, such as NMR, FTIR, SEC-MALLS/RI, MALDI-TOF-MS, RP-HPLC and polyelectrolyte titration were used to evaluate the products from different perspectives and to acquire parallel proofs of their chemical structure. Modified GGMs with different degree of substitution and the correlating level of hydrophobicity was applied as coatings on cartonboard and on nanofibrillated cellulose-GGM films to exhibit barrier functionality. The water dispersibility in processing was maintained with GGM esters with low DS. The use of chemically functionalised GGM was evaluated for the use as barriers against water, oxygen and grease for the food packaging purposes. The results show undoubtedly that GGM derivatives exhibit high potential to function as a barrier material in food packaging.

Effect of an edible crosslinked coating and two types of packaging on antioxidant capacity of castilla blackberries

In order to increase the shelf life and maintain the quality and stability of the biological compounds with antioxidant activity present in Castilla blackberry fruits, a sodium alginate-based edible crosslinked coating was applied, and the fruits were packed in two different plastic containers and stored under refrigeration (3 ± 1 °C). Total antioxidant capacity and its relationship to physicochemical variables such as pH, Brix, and acidity were evaluated in six treatments: uncoated blackberry stored in a macroperforated container (T1) and thermosealed container (T2), without crosslinked coating in a macroperforated container (T3) and thermosealed container (T4), with crosslinked coating (calcium ions) packed in macroperforated container (T5) and thermosealed container (T6). The results indicated that factors such as gas permeability in the coatings, the packaging used, and physicochemical parameters significantly affected the fruit total antioxidant capacity, with the highest level in T1 (0.22 µgEAA/ml) at the end of the essay, which is related to the lowest levels of pH and direct exposure to air. On the other hand, the lowest value was obtained in T6 (0.16 µgEAA/ml) due to the crosslinked coating, packaging in the thermosealed container, and higher pH value. Variations in acidity, Brix, and pH indicate the presence of degenerative processes in the crosslinked coating treatments, which limited the physicochemical changes.

Weldability of high strength aluminium alloys

The need for reduced intrinsic weight of structures and vehicles in the transportation industry has made aluminium research of interest. Aluminium has properties that are favourable for structural engineering, including good strength-to-weight ratio, corrosion resistance and machinability. It can be easily recycled saving energy used in smelting as compared to steel. Its alloys can have ultimate tensile strength of up to 750 MPa, which is comparable to steel. Aluminium alloys are generally weldable, however welding of high strength alloys like the 7xxx series pose considerable challenges. This paper presents research on the weldability of high strength aluminium alloys, principally the 7xxx series. The weldability with various weld processes including MIG, TIG, and FSW, is discussed in addition to consideration of joint types, weld defects and recommendations for minimizing or preventing weld defects. Experimental research was carried out on 7025-T6 and AW-7020 alloys. Samples were welded, and weld cross sections utilized in weld metallurgy studies. Mechanical tests were carried out including hardness tests and tensile tests. In addition, testing was done for the presence of Al2O3 on exposed aluminium alloy. It was observed that at constant weld heat input using a pulsed MIG system, the welding speed had little or no effect on the weld hardness. However, the grain size increased as the filler wire feed rate, welding current and welding speed increased. High heat input resulted in lower hardness of the weld profile. Weld preheating was detrimental to AW- 7020 welds; however, artificial aging was beneficial. Acceptable welds were attained with pulsed MIG without the removal of the Al2O3 layer prior to welding. The Al2O3 oxide layer was found to have different compositions in different aluminium alloys. These findings contribute useful additional information to the knowledge base of aluminium welding. The application of the findings of this study in welding will help reduce weld cost and improve high strength aluminium structure productivity by removing the need for pre-weld cleaning. Better understanding of aluminium weld metallurgy equips weld engineers with information for better aluminium weld design.

The effect of cationic-anionic polyelectrolyte multilayer surface treatment on inkjet ink spreading and print quality

The focus of the work reported in this thesis was to study and to clarify the effect of polyelectrolyte multilayer surface treatment on inkjet ink spreading, absorption and print quality. Surface sizing with a size press, film press with a pilot scale coater, and spray coating, have been used to surface treat uncoated wood-free, experimental wood-free and pigmentcoated substrates. The role of the deposited cationic (polydiallydimethylammonium chloride, PDADMAC) and anionic (sodium carboxymethyl cellulose, NaCMC) polyelectrolyte layers with and without nanosilica, on liquid absorption and spreading was studied in terms of their interaction with water-based pigmented and dye-based inkjet inks. Contact angle measurements were made in attempt to explain the ink spreading and wetting behavior on the substrate. First, it was noticed that multilayer surface treatment decreased the contact angle of water, giving a hydrophilic character to the surface. The results showed that the number of cationic-anionic polyelectrolyte layers or the order of deposition of the polyelectrolytes had a significant effect on the print quality. This was seen for example as a higher print density on layers with a cationic polyelectrolyte in the outermost layer. The number of layers had an influence on the print quality; the print density increased with increasing number of layers, although the increase was strongly dependent on ink formulation and chemistry. The use of nanosilica clearly affected the rate of absorption of polar liquids, which also was seen as a higher density of the black dye-based print. Slightly unexpected, the use of nanosilica increased the tendency for lateral spreading of both the pigmented and dye-based inks. It was shown that the wetting behavior and wicking of the inks on the polyelectrolyte coatings was strongly affected by the hydrophobicity of the substrate, as well as by the composition or structure of the polyelectrolyte layers. Coating only with a cationic polyelectrolyte was not sufficient to improve dye fixation, but it was demonstrated that a cationic-anionic-complex structure led to good water fastness. A threelayered structure gave the same water fastness values as a five-layered structure. Interestingly, the water fastness values were strongly dependent not only on the formed cation-anion polyelectrolyte complexes but also on the tendency of the coating to dissolve during immersion in water. Results showed that by optimizing the chemistry of the layers, the ink-substrate interaction can be optimized.

Paperikoneen kuivatusosan olosuhteiden vaikutus viiranjohtotelojen vaipan materiaalin ja pinnoitteen valintaan korroosiovaurion ehkäisemiseksi

Diplomityön tavoitteena on löytää UPM Kymin paperikone 8:n ensimmäisen kuivatusryhmän johtoteloihin kulumis- ja korroosiokestävämpi materiaali ja pinnoite vallitsevaan olosuhteeseen. Teloihin muodostuu pistemäistä korroosiota ja korroosioalue on paikallinen. Korroosiota syntyy kuivatusviiran alueella, jossa ei ole paperirainaa. Työssä suoritetaan kuivatusosan olosuhdemittauksia ja tutkitaan niiden vaikutuksia korroosion muodostumiseen. Suoritettavat olosuhdemittaukset ovat huuvan ilmatase, paineen 0-taso sekä lämpötilat ja kosteudet eri huuvan osissa. Savukaasumittauksen avulla tutkitaan huuvan ilmankiertoa ensimmäisen kuivatusryhmän viiranjohtotelojen läheisyydessä. Kuivatusviiran ilmanläpäisymittauksen avulla saadaan tietoa viiran ilmanläpäisykyvystä. Hypoteesina viiran tukkeutuminen johtuu pölyävästä kuivaus-prosessista ja kosteudesta. SEM/EDS-alkuainemittauksen avulla pystytään analysoimaan korrosiivisia alkuaineita niin korroosioalueella kuin ympäristössä. Työn tutkimuksen perusteella korroosion muodostuminen aiheutuu tukkeutuneen viiran muodostamasta happipitoisuuseroalueesta. Viiran saostumat sisältävät korrosiivisia kemikaaleja, kuten kloridia, rikkiä ja mangaania. Nämä kiihdyttävät korroosiota happipuutosalueella. Huuvan olosuhdemittauksien perusteella huuvan paineen 0-taso on vino. Savukaasu- ja kosteusmittauksien avulla huomattiin kostean ilman jäävän telojen läheisyyteen. Työssä kehitettiin paineilmapuhdistin viiran reuna-alueen puhdistamiseen. Kaavattaviin telapositioihin valittiin kobolttikromiseostettu volframikarbidipinnoite PTFE -fluoripolymeeritiivistyksellä. Muihin telapositioihin valittiin ETFE –fluori-polymeeripinnoite korroosion ehkäisemiseksi. Pinnoitteiden ja paineilmapuhdistimen avulla telojen käyttöaika nousee nykyisestä kahdesta vuodesta tavoiteltuun 10 vuoteen.

Revêtement anti-apoptotique à base de chondroïtine sulfate : vers un stent-graft bioactif

La réparation endovasculaire (EVAR) est une technique minimalement invasive permettant de traiter l’anévrisme de l’aorte abdominale (AAA) par l’entremise d’un stent- graft (SG). L’utilisation d’EVAR est actuellement limitée par de fréquentes complications liées à une guérison inadéquate autour de l’implant. Ce manque de guérison est principalement dû au type de recouvrement polymérique des SG, au milieu pro-apoptotique des AAA et à l’accès réduit aux nutriments et à l’oxygène après EVAR. L’objectif de cette thèse consistait à concevoir un revêtement bioactif permettant d’inhiber l’apoptose et stimuler la croissance des cellules musculaires lisses vasculaires (CMLV), pour ainsi favoriser la guérison des tissus vasculaires autour des SG. La chondroïtine-4-sulfate (CS) a d’abord été choisie, car elle a été identifiée comme un médiateur important de la réparation vasculaire. Il a été démontré que la CS en solution influence directement la résistance à l’apoptose des CMLV, en plus de favoriser la différenciation myofibroblastique chez les fibroblastes. Dans le cadre de ce projet, un premier revêtement à base de CS et de collagène a été créé. Bien que le revêtement permettait d’induire une résistance à l’apoptose chez les CMLV, il se désintégrait trop rapidement dans des conditions aqueuses. Une nouvelle méthodologie a donc été adaptée afin de greffer la CS directement sur des surfaces aminées, à l’aide d’un système utilisant un carbodiimide. Dans le but d’accroître la croissance des CMLV à la surface des revêtements, le facteur de croissance de l’épiderme (EGF) a ensuite été sélectionné. En plus de ses propriétés mitogéniques et chimiotactiques, l’EGF stimule la production d’éléments de la matrice extracellulaire, comme le collagène et la fibronectine. De plus, l’activation du récepteur de l’EGF inhibe également l’apoptose des CMLV. L’EGF a donc été greffé sur la CS. Le revêtement de CS+EGF a démontré une bonne uniformité et bioactivité sur des surfaces de verre aminé. iii iv Dans une 3ème étape, afin de permettre de transposer ce revêtement bioactif sur des implants, plusieurs méthodes permettant de créer des groupements d’amines primaires sur les biomatériaux polymériques comme le PET ou le ePTFE ont été étudiées. La polymérisation par plasma a été choisie pour créer le revêtement CS+EGF à la surface de PET. Une fois de plus, celui-ci a permis d’inhiber l’apoptose des CMLV, dans des conditions pro-apoptotiques, et de favoriser la croissance des cellules. Le revêtement de CS et d’EGF, déposé sur des surfaces aminées, possède des caractéristiques biologiques intéressantes et semble donc prometteur pour favoriser une meilleure guérison autour des SG.

Rapport M/L de disques de galaxies issus de modèles CSPE et contrôle des contraintes mécaniques dans la conception de revêtements optiques

La thèse qui suit est organisée en deux volets: un premier volet portant sur les modèles de masse de galaxies et un second volet sur la conception de revêtements optiques et le contrôle de leurs propriétés mécaniques. Les modèles de masse présentés dans cette thèse ont été réalisés sur un sous-échantillon de dix galaxies de l'étude SINGS comprenant neuf galaxies normales et une galaxie naine. Ce travail visait à fixer le rapport masse-luminosité du disque à tout rayon en utilisant les résultats de modèles d'évolution galactique chimio-spectrophotométriques ajustés spécifiquement à chaque galaxie grâce à son profil de photométrie multi-bandes. Les résultats montrent que les disques stellaires tels que normalisés par les rapports masse-luminosité issus des modèles ont des masses cohérentes dans toutes les bandes étudiées de l'ultra-violet, du visible ainsi que du proche infrarouge (bandes FUV à IRAC2). Ces disques peuvent être considérés comme maximaux par rapport aux données cinématiques des galaxies étudiées. Ceci est dû au fait que le rapport M/L est plus élevé au centre que sur les bords. Les disques étant maximaux et physiquement justifiés, on ne peut dès lors ignorer les effets de composants tels que les bulbes ou les barres et les corrections nécessaires doivent être apportées aux profils de luminosité et de vitesses de rotation de la galaxie. Dans les travaux de la seconde partie, le logiciel en développement libre OpenFilters a été modifié afin de tenir compte des contraintes mécaniques dans la conception numérique de revêtements optiques. Les contraintes mécaniques dans les couches minces ont un effet délétère sur leurs performances optiques. Un revêtement destiné à rendre réflectives les lames d'un étalon Fabry-Perot utilisé en astronomie a été conçu et fabriqué afin d'évaluer les performances réelles de la méthode. Ce cas a été choisi à cause de la diminution de la finesse d'un étalon Fabry-Perot apporté par la courbure des lames sous l'effet des contraintes. Les résultats montrent que les mesures concordent avec les modèles numériques et qu'il est donc possible à l'aide de ce logiciel d'optimiser les revêtements pour leur comportement mécanique autant que pour leurs propriétés optiques.

L’étude des stratégies de séparations préparatrices de protéines par électrophorèse capillaire

La protéomique est un sujet d'intérêt puisque l'étude des fonctions et des structures de protéines est essentiel à la compréhension du fonctionnement d'un organisme donné. Ce projet se situe dans la catégorie des études structurales, ou plus précisément, la séquence primaire en acides aminés pour l’identification d’une protéine. La détermination des protéines commence par l'extraction d'un mélange protéique issu d'un tissu ou d'un fluide biologique pouvant contenir plus de 1000 protéines différentes. Ensuite, des techniques analytiques comme l’électrophorèse en gel polyacrylamide en deux dimensions (2D-SDS-PAGE), qui visent à séparer ce mélange en fonction du point isoélectrique et de la masse molaire des protéines, sont utilisées pour isoler les protéines et pour permettre leur identification par chromatographie liquide and spectrométrie de masse (MS), typiquement. Ce projet s'inspire de ce processus et propose que l'étape de fractionnement de l'extrait protéique avec la 2D-SDS-PAGE soit remplacé ou supporté par de multiples fractionnements en parallèle par électrophorèse capillaire (CE) quasi-multidimensionnelle. Les fractions obtenues, contenant une protéine seule ou un mélange de protéines moins complexe que l’extrait du départ, pourraient ensuite être soumises à des identifications de protéines par cartographie peptidique et cartographie protéique à l’aide des techniques de séparations analytiques et de la MS. Pour obtenir la carte peptidique d'un échantillon, il est nécessaire de procéder à la protéolyse enzymatique ou chimique des protéines purifiées et de séparer les fragments peptidiques issus de cette digestion. Les cartes peptidiques ainsi générées peuvent ensuite être comparées à des échantillons témoins ou les masses exactes des peptides enzymatiques sont soumises à des moteurs de recherche comme MASCOT™, ce qui permet l’identification des protéines en interrogeant les bases de données génomiques. Les avantages exploitables de la CE, par rapport à la 2D-SDS-PAGE, sont sa haute efficacité de séparation, sa rapidité d'analyse et sa facilité d'automatisation. L’un des défis à surmonter est la faible quantité de masse de protéines disponible après analyses en CE, due partiellement à l'adsorption des protéines sur la paroi du capillaire, mais due majoritairement au faible volume d'échantillon en CE. Pour augmenter ce volume, un capillaire de 75 µm était utilisé. Aussi, le volume de la fraction collectée était diminué de 1000 à 100 µL et les fractions étaient accumulées 10 fois; c’est-à-dire que 10 produits de séparations étaient contenu dans chaque fraction. D'un autre côté, l'adsorption de protéines se traduit par la variation de l'aire d'un pic et du temps de migration d'une protéine donnée ce qui influence la reproductibilité de la séparation, un aspect très important puisque 10 séparations cumulatives sont nécessaires pour la collecte de fractions. De nombreuses approches existent pour diminuer ce problème (e.g. les extrêmes de pH de l’électrolyte de fond, les revêtements dynamique ou permanent du capillaire, etc.), mais dans ce mémoire, les études de revêtement portaient sur le bromure de N,N-didodecyl-N,N-dimethylammonium (DDAB), un surfactant qui forme un revêtement semi-permanent sur la paroi du capillaire. La grande majorité du mémoire visait à obtenir une séparation reproductible d'un mélange protéique standard préparé en laboratoire (contenant l’albumine de sérum de bovin, l'anhydrase carbonique, l’α-lactalbumine et la β-lactoglobulin) par CE avec le revêtement DDAB. Les études portées sur le revêtement montraient qu'il était nécessaire de régénérer le revêtement entre chaque injection du mélange de protéines dans les conditions étudiées : la collecte de 5 fractions de 6 min chacune à travers une séparation de 30 min, suivant le processus de régénération du DDAB, et tout ça répété 10 fois. Cependant, l’analyse en CE-UV et en HPLC-MS des fractions collectées ne montraient pas les protéines attendues puisqu'elles semblaient être en-dessous de la limite de détection. De plus, une analyse en MS montrait que le DDAB s’accumule dans les fractions collectées dû à sa désorption de la paroi du capillaire. Pour confirmer que les efforts pour recueillir une quantité de masse de protéine étaient suffisants, la méthode de CE avec détection par fluorescence induite par laser (CE-LIF) était utilisée pour séparer et collecter la protéine, albumine marquée de fluorescéine isothiocyanate (FITC), sans l'utilisation du revêtement DDAB. Ces analyses montraient que l'albumine-FITC était, en fait, présente dans la fraction collecté. La cartographie peptidique a été ensuite réalisée avec succès en employant l’enzyme chymotrypsine pour la digestion et CE-LIF pour obtenir la carte peptidique.

Spray Pyrolysed Zinc Oxide Thin Films : Effects of Doping and Ion Beam Irradiation

In recent years scientists have made rapid and significant advances in the field of semiconductor physics. One of the most important fields of current interest in materials science is the fundamental aspects and applications of conducting transparent oxide thin films (TCO). The characteristic properties of such coatings are low electrical resistivity and high transparency in the visible region. The first semitransparent and electrically conducting CdO film was reported as early as in 1907 [1]. Though early work on these films was performed out of purely scientific interest, substantial technological advances in such films were made after 1940. The technological interest in the study of transparent semiconducting films was generated mainly due to the potential applications of these materials both in industry and research. Such films demonstrated their utility as transparent electrical heaters for windscreens in the aircraft industry. However, during the last decade, these conducting transparent films have been widely used in a variety of other applications such as gas sensors [2], solar cells [3], heat reflectors [4], light emitting devices [5] and laser damage resistant coatings in high power laser technology [6]. Just a few materials dominate the current TCO industry and the two dominant markets for TCO’s are in architectural applications and flat panel displays. The architectural use of TCO is for energy efficient windows. Fluorine doped tin oxide (FTO), deposited using a pyrolysis process is the TCO usually finds maximum application. SnO2 also finds application ad coatings for windows, which are efficient in preventing radiative heat loss, due to low emissivity (0.16). Pyrolitic tin oxide is used in PV modules, touch screens and plasma displays. However indium tin oxide (ITO) is mostly used in the majority of flat panel display (FPD) applications. In FPDs, the basic function of ITO is as transparent electrodes. The volume of FPD’s produced, and hence the volume of ITO coatings produced, continues to grow rapidly. But the current increase in the cost of indium and the scarcity of this material created the difficulty in obtaining low cost TCOs. Hence search for alternative TCO materials has been a topic of active research for the last few decades. This resulted in the development of binary materials like ZnO, SnO2, CdO and ternary materials like II Zn2SnO4, CdSb2O6:Y, ZnSO3, GaInO3 etc. The use of multicomponent oxide materials makes it possible to have TCO films suitable for specialized applications because by altering their chemical compositions, one can control the electrical, optical, chemical and physical properties. But the advantages of using binary materials are the easiness to control the chemical compositions and depositions conditions. Recently, there were reports claiming the deposition of CdO:In films with a resistivity of the order of 10-5 ohm cm for flat panel displays and solar cells. However they find limited use because of Cd-Toxicity. In this regard, ZnO films developed in 1980s, are very useful as these use Zn, an abundant, inexpensive and nontoxic material. Resistivity of this material is still not very low, but can be reduced through doping with group-III elements like In, Al or Ga or with F [6]. Hence there is a great interest in ZnO as an alternative of ITO. In the present study, we prepared and characterized transparent and conducting ZnO thin films, using a cost effective technique viz Chemical Spray Pyrolysis (CSP). This technique is also suitable for large area film deposition. It involves spraying a solution, (usually aqueous) containing soluble salts of the constituents of the desired compound, onto a heated substrate.

Growth and Characterisation of Radio Frequency Magnetron Sputttered Indium Tin Oxide Thin Films

The increasing interest in the interaction of light with electricity and electronically active materials made the materials and techniques for producing semitransparent electrically conducting films particularly attractive. Transparent conductors have found major applications in a number of electronic and optoelectronic devices including resistors, transparent heating elements, antistatic and electromagnetic shield coatings, transparent electrode for solar cells, antireflection coatings, heat reflecting mirrors in glass windows and many other. Tin doped indium oxide (indium tin oxide or ITO) is one of the most commonly used transparent conducting oxides. At present and likely well into the future this material offers best available performance in terms of conductivity and transmittivity combined with excellent environmental stability, reproducibility and good surface morphology. Although partial transparency, with a reduction in conductivity, can be obtained for very thin metallic films, high transparency and simultaneously high conductivity cannot be attained in intrinsic stoichiometric materials. The only way this can be achieved is by creating electron degeneracy in a wide bandgap (Eg > 3eV or more for visible radiation) material by controllably introducing non-stoichiometry and/or appropriate dopants. These conditions can be conveniently met for ITO as well as a number of other materials like Zinc oxide, Cadmium oxide etc. ITO shows interesting and technologically important combination of properties viz high luminous transmittance, high IR reflectance, good electrical conductivity, excellent substrate adherence and chemical inertness. ITO is a key part of solar cells, window coatings, energy efficient buildings, and flat panel displays. In solar cells, ITO can be the transparent, conducting top layer that lets light into the cell to shine the junction and lets electricity flow out. Improving the ITO layer can help improve the solar cell efficiency. A transparent ii conducting oxide is a material with high transparency in a derived part of the spectrum and high electrical conductivity. Beyond these key properties of transparent conducting oxides (TCOs), ITO has a number of other key characteristics. The structure of ITO can be amorphous, crystalline, or mixed, depending on the deposition temperature and atmosphere. The electro-optical properties are a function of the crystallinity of the material. In general, ITO deposited at room temperature is amorphous, and ITO deposited at higher temperatures is crystalline. Depositing at high temperatures is more expensive than at room temperature, and this method may not be compatible with the underlying devices. The main objective of this thesis work is to optimise the growth conditions of Indium tin oxide thin films at low processing temperatures. The films are prepared by radio frequency magnetron sputtering under various deposition conditions. The films are also deposited on to flexible substrates by employing bias sputtering technique. The films thus grown were characterised using different tools. A powder x-ray diffractometer was used to analyse the crystalline nature of the films. The energy dispersive x-ray analysis (EDX) and scanning electron microscopy (SEM) were used for evaluating the composition and morphology of the films. Optical properties were investigated using the UVVIS- NIR spectrophotometer by recording the transmission/absorption spectra. The electrical properties were studied using vander Pauw four probe technique. The plasma generated during the sputtering of the ITO target was analysed using Langmuir probe and optical emission spectral studies.

Growth of zinc oxide thin films for optoelectronic application by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on quartz, silicon, and polymer substrates by pulsed laser deposition (PLD) technique at different oxygen partial pressures (0.007 mbar to 0.003 mbar). Polycrystalline ZnO films were obtained at room temperature when the oxygen pressure was between 0.003 mbar and .007 mbar, above and below this pressure the films were amorphous as indicated by the X-ray diffraction (XRD). ZnO films were deposited on Al2O3 (0001) at different substrate temperatures varying from 400oC to 600oC and full width half maximum (FWHM) of XRD peak is observed to decrease as substrate temperature increases. The optical band gaps of these films were nearly 3.3 eV. A cylindrical Langmuir probe is used for the investigation of plasma plume arising from the ZnO target. The spatial and temporal variations in electron density and electron temperature are studied. Optical emission spectroscopy is used to identify the different ionic species in the plume. Strong emission lines of neutral Zn, Zn+ and neutral oxygen are observed. No electronically excited O+ cations are identified, which is in agreement with previous studies of ZnO plasma plume.

Studies on Chemical Bath Deposited Semiconducting Copper Selenide and Iron Sulfide Thin Films Useful For Photovoltaic Applications

Chemical bath deposition (CBD)is one of the simplest, very convient and probably the cheapest method for thin film preparation. Photovoltaic is the cleanest and the most efficient mode of conversion of energy to electrical power. Silicon is the most popular material in this field. The present study on chemical bath deposited semiconducting copper selenide and iron sulfide thin films useful for photovoltaic applications. Semiconducting thin films prepared by chemical deposition find applications as photo detectors, solar control coatings and solar cells. Copper selenide is a p-type semiconductor that finds application in photovolitics. Several heterojunction systems such as Cu2-xSe/ZnSe (for injection electro luminescence), Cu2Se/AgInSe2 and Cu2Se/Si (for photodiodes), Cu2-xSe/CdS, Cu2-xSe/CdSe, CuxSe/InP and Cu2-xSe/Si for solar cells are reported. A maximum efficiency of 8.3% was achieved for the Cu2-xSe/Si cell, various preparation techniques are used for copper selenide like vacuum evaporation, direct reaction, electrodeposition and CBD. Instability of the as-prepared films was investigation and is accounted as mainly due to deviation from stoichiometry and the formation of iron oxide impurity. A sulphur annealing chamber was designed and fabricated for this work. These samples wee also analysed using optical absorption technique, XPS (X-ray Photoelectron Spectroscopy) and XRD.(X-Ray Diffraction).The pyrite films obtained by CBD technique showed amorphous nature and the electrical studies carried out showed the films to be of high resistive nature. Future work possible in the material of iron pyrite includes sulphur annealing of the non-stochiometric iron pyrite CBD thin films in the absence of atmospheric oxygen

Sol-Gel Mesoporous Silica Aerogels and Bio Hybrids for Functional Applications

The thesis covers a systematic investigation on the synthesis of silica aerogels and microspheres with tailored porosity, at ambient conditions by varying the experimental parameters as well as using organic templates. Organically modified silica-gelatin and silica-chitosan hybrids were developed for the first time using alkylalkoxysilanes such as MTMS and VTMS. Application of novel silica-biopolymer antiwetting coatings on different substrates such as glass, leather and textile is also demonstrated in the thesis.