VO2 Kinetics During Heavy and Severe Exercise in Swimming

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The validity of critical speed determined from track cycling for identification of the maximal lactate steady state

The objective of this study was to determine the critical speed (CS) for track cycling and to assess whether a lactate steady state occurs at this speed. Fourteen competitive cyclists performed the following tests on an official cycling track (333.3 m): 1) incremental test for determination of the intensity corresponding to 4 mM of blood lactate (onset of blood lactate accumulation, OBLA) and maximal oxygen uptake (VO(2)max); 2) CS: 3 maximal bouts for distances of 2, 4 and 6 km executed in random order and with a period of recovery of 40 to 50 min between bouts. CS was determined for each subject from the linear regression between the distance and the time taking to cycle it; 3) Endurance test in which subjects were instructed to pedal at 100% of their individually determined CS for 30 min. At the 10(th) and 30(th) min (or upon exhaustion), 25 mul of blood were collected from ear lobe for later analysis of blood lactate [Lac]b. An increase less than or equal to1 mM between 10 and 30 min of exercise was considered as the criterion for the occurrence of the lactate steady state. CS (49.6 +/- 8.6 ml.kg(-1).min(-1); 36.9 +/- 2.7 km.h(-1)) was significantly higher than OBLA (43.7 8.0 ml.kg(-1).min(-1); 35.24 +/- 2.6 km.h(-1)) although the two parameters were highly correlated (r=0.97). During the endurance test, only 8 of the 14 subjects completed the 30 min period at CS. of these 8 subjects, only 2 presented a lactate steady state. Time to exhaustion at CS was 20.3 +/- 1.6 min for the remaining 6 subjects. The 12 subjects who did not reach a lactate steady state presented mean [Lac]b values of 7.4 +/- 1.3 mM at 10 min and of 9.4 +/- 1.9 mM at the end of the test (exhaustion), characterizing an exercise intensity of high lactacidemia. on the basis of the present results, we can conclude that CS determined by a track cycling test seems to overestimate the intensity of the maximal lactate steady state for most subjects.

Estimating the loading condition of a diesel engine using instantaneous angular speed analysis

Continuing monitoring of diesel engine performance is critical for early detection of fault developments in the engine before they materialize and become a functional failure. Instantaneous crank angular speed (IAS) analysis is one of a few non intrusive condition monitoring techniques that can be utilized for such tasks. In this experimental study, IAS analysis was employed to estimate the loading condition of a 4-stroke 4-cylinder diesel engine in a laboratory condition. It was shown that IAS analysis can provide useful information about engine speed variation caused by the changing piston momentum and crankshaft acceleration during the engine combustion process. It was also found that the major order component of the IAS spectrum directly associated with the engine firing frequency (at twice the mean shaft revolution speed) can be utilized to estimate the engine loading condition regardless of whether the engine is operating at normal running conditions or in a simulated faulty injector case. The amplitude of this order component follows a clear exponential curve as the loading condition changes. A mathematical relationship was established for the estimation of the engine power output based on the amplitude of the major order component of the measured IAS spectrum.

Estimating the loading condition of a diesel engine using instantaneous angular speed analysis

Continuing monitoring of diesel engine performance is critical for early detection of fault developments in the engine before they materialize and become a functional failure. Instantaneous crank angular speed (IAS) analysis is one of a few non intrusive condition monitoring techniques that can be utilized for such tasks. In this experimental study, IAS analysis was employed to estimate the loading condition of a 4-stroke 4-cylinder diesel engine in a laboratory condition. It was shown that IAS analysis can provide useful information about engine speed variation caused by the changing piston momentum and crankshaft acceleration during the engine combustion process. It was also found that the major order component of the IAS spectrum directly associated with the engine firing frequency (at twice the mean shaft revolution speed) can be utilized to estimate the engine loading condition regardless of whether the engine is operating at normal running conditions or in a simulated faulty injector case. The amplitude of this order component follows a clear exponential curve as the loading condition changes. A mathematical relationship was established for the estimation of the engine power output based on the amplitude of the major order component of the measured IAS spectrum.

The relationship between drivers’ perceptions toward police speed enforcement and self-reported speeding behaviour

Exceeding the speed limit and driving too fast for the conditions are regularly cited as significant contributing factors in traffic crashes, particularly fatal and serious injury crashes. Despite an extensive body of research highlighting the relationship between increased vehicle speeds and crash risk and severity, speeding remains a pervasive behaviour on Australian roads. The development of effective countermeasures designed to reduce the prevalence of speeding behaviour requires that this behaviour is well understood. The primary aim of this program of research was to develop a better understanding of the influence of drivers’ perceptions and attitudes toward police speed enforcement on speeding behaviour. Study 1 employed focus group discussions with 39 licensed drivers to explore the influence of perceptions relating to specific characteristics of speed enforcement policies and practices on drivers’ attitudes towards speed enforcement. Three primary factors were identified as being most influential: site selection; visibility; and automaticity (i.e., whether the enforcement approach is automated/camera-based or manually operated). Perceptions regarding these enforcement characteristics were found to influence attitudes regarding the perceived legitimacy and transparency of speed enforcement. Moreover, misperceptions regarding speed enforcement policies and practices appeared to also have a substantial impact on attitudes toward speed enforcement, typically in a negative direction. These findings have important implications for road safety given that prior research has suggested that the effectiveness of speed enforcement approaches may be reduced if efforts are perceived by drivers as being illegitimate, such that they do little to encourage voluntary compliance. Study 1 also examined the impact of speed enforcement approaches varying in the degree of visibility and automaticity on self-reported willingness to comply with speed limits. These discussions suggested that all of the examined speed enforcement approaches (see Section 1.5 for more details) generally showed potential to reduce vehicle speeds and encourage compliance with posted speed limits. Nonetheless, participant responses suggested a greater willingness to comply with approaches operated in a highly visible manner, irrespective of the corresponding level of automaticity of the approach. While less visible approaches were typically associated with poorer rates of driver acceptance (e.g., perceived as “sneaky” and “unfair”), participants reported that such approaches would likely encourage long-term and network-wide impacts on their own speeding behaviour, as a function of the increased unpredictability of operations and increased direct (specific deterrence) and vicarious (general deterrence) experiences with punishment. Participants in Study 1 suggested that automated approaches, particularly when operated in a highly visible manner, do little to encourage compliance with speed limits except in the immediate vicinity of the enforcement location. While speed cameras have been criticised on such grounds in the past, such approaches can still have substantial road safety benefits if implemented in high-risk settings. Moreover, site-learning effects associated with automated approaches can also be argued to be a beneficial by-product of enforcement, such that behavioural modifications are achieved even in the absence of actual enforcement. Conversely, manually operated approaches were reported to be associated with more network-wide impacts on behaviour. In addition, the reported acceptance of such methods was high, due to the increased swiftness of punishment, ability for additional illegal driving behaviours to be policed and the salutary influence associated with increased face-to-face contact with authority. Study 2 involved a quantitative survey conducted with 718 licensed Queensland drivers from metropolitan and regional areas. The survey sought to further examine the influence of the visibility and automaticity of operations on self-reported likelihood and duration of compliance. Overall, the results from Study 2 corroborated those of Study 1. All examined approaches were again found to encourage compliance with speed limits, such that all approaches could be considered to be “effective”. Nonetheless, significantly greater self-reported likelihood and duration of compliance was associated with visibly operated approaches, irrespective of the corresponding automaticity of the approach. In addition, the impact of automaticity was influenced by visibility; such that significantly greater self-reported likelihood of compliance was associated with manually operated approaches, but only when they are operated in a less visible fashion. Conversely, manually operated approaches were associated with significantly greater durations of self-reported compliance, but only when they are operated in a highly visible manner. Taken together, the findings from Studies 1 and 2 suggest that enforcement efforts, irrespective of their visibility or automaticity, generally encourage compliance with speed limits. However, the duration of these effects on behaviour upon removal of the enforcement efforts remains questionable and represents an area where current speed enforcement practices could possibly be improved. Overall, it appears that identifying the optimal mix of enforcement operations, implementing them at a sufficient intensity and increasing the unpredictability of enforcement efforts (e.g., greater use of less visible approaches, random scheduling) are critical elements of success. Hierarchical multiple regression analyses were also performed in Study 2 to investigate the punishment-related and attitudinal constructs that influence self-reported frequency of speeding behaviour. The research was based on the theoretical framework of expanded deterrence theory, augmented with three particular attitudinal constructs. Specifically, previous research examining the influence of attitudes on speeding behaviour has typically focussed on attitudes toward speeding behaviour in general only. This research sought to more comprehensively explore the influence of attitudes by also individually measuring and analysing attitudes toward speed enforcement and attitudes toward the appropriateness of speed limits on speeding behaviour. Consistent with previous research, a number of classical and expanded deterrence theory variables were found to significantly predict self-reported frequency of speeding behaviour. Significantly greater speeding behaviour was typically reported by those participants who perceived punishment associated with speeding to be less certain, who reported more frequent use of punishment avoidance strategies and who reported greater direct experiences with punishment. A number of interesting differences in the significant predictors among males and females, as well as younger and older drivers, were reported. Specifically, classical deterrence theory variables appeared most influential on the speeding behaviour of males and younger drivers, while expanded deterrence theory constructs appeared more influential for females. These findings have important implications for the development and implementation of speeding countermeasures. Of the attitudinal factors, significantly greater self-reported frequency of speeding behaviour was reported among participants who held more favourable attitudes toward speeding and who perceived speed limits to be set inappropriately low. Disappointingly, attitudes toward speed enforcement were found to have little influence on reported speeding behaviour, over and above the other deterrence theory and attitudinal constructs. Indeed, the relationship between attitudes toward speed enforcement and self-reported speeding behaviour was completely accounted for by attitudes toward speeding. Nonetheless, the complexity of attitudes toward speed enforcement are not yet fully understood and future research should more comprehensively explore the measurement of this construct. Finally, given the wealth of evidence (both in general and emerging from this program of research) highlighting the association between punishment avoidance and speeding behaviour, Study 2 also sought to investigate the factors that influence the self-reported propensity to use punishment avoidance strategies. A standard multiple regression analysis was conducted for exploratory purposes only. The results revealed that punishment-related and attitudinal factors significantly predicted approximately one fifth of the variance in the dependent variable. The perceived ability to avoid punishment, vicarious punishment experience, vicarious punishment avoidance and attitudes toward speeding were all significant predictors. Future research should examine these relationships more thoroughly and identify additional influential factors. In summary, the current program of research has a number of implications for road safety and speed enforcement policy and practice decision-making. The research highlights a number of potential avenues for the improvement of public education regarding enforcement efforts and provides a number of insights into punishment avoidance behaviours. In addition, the research adds strength to the argument that enforcement approaches should not only demonstrate effectiveness in achieving key road safety objectives, such as reduced vehicle speeds and associated crashes, but also strive to be transparent and legitimate, such that voluntary compliance is encouraged. A number of potential strategies are discussed (e.g., point-to-point speed cameras, intelligent speed adaptation. The correct mix and intensity of enforcement approaches appears critical for achieving optimum effectiveness from enforcement efforts, as well as enhancements in the unpredictability of operations and swiftness of punishment. Achievement of these goals should increase both the general and specific deterrent effects associated with enforcement through an increased perceived risk of detection and a more balanced exposure to punishment and punishment avoidance experiences.

A practical signal processing approach for condition monitoring of low speed machinery using Peak-Hold-Down-Sample algorithm

A simple and effective down-sample algorithm, Peak-Hold-Down-Sample (PHDS) algorithm is developed in this paper to enable a rapid and efficient data transfer in remote condition monitoring applications. The algorithm is particularly useful for high frequency Condition Monitoring (CM) techniques, and for low speed machine applications since the combination of the high sampling frequency and low rotating speed will generally lead to large unwieldy data size. The effectiveness of the algorithm was evaluated and tested on four sets of data in the study. One set of the data was extracted from the condition monitoring signal of a practical industry application. Another set of data was acquired from a low speed machine test rig in the laboratory. The other two sets of data were computer simulated bearing defect signals having either a single or multiple bearing defects. The results disclose that the PHDS algorithm can substantially reduce the size of data while preserving the critical bearing defect information for all the data sets used in this work even when a large down-sample ratio was used (i.e., 500 times down-sampled). In contrast, the down-sample process using existing normal down-sample technique in signal processing eliminates the useful and critical information such as bearing defect frequencies in a signal when the same down-sample ratio was employed. Noise and artificial frequency components were also induced by the normal down-sample technique, thus limits its usefulness for machine condition monitoring applications.

Faster than the speed of print : reconciling ‘big data’ social media analysis and academic scholarship

The promise of ‘big data’ has generated a significant deal of interest in the development of new approaches to research in the humanities and social sciences, as well as a range of important critical interventions which warn of an unquestioned rush to ‘big data’. Drawing on the experiences made in developing innovative ‘big data’ approaches to social media research, this paper examines some of the repercussions for the scholarly research and publication practices of those researchers who do pursue the path of ‘big data’–centric investigation in their work. As researchers import the tools and methods of highly quantitative, statistical analysis from the ‘hard’ sciences into computational, digital humanities research, must they also subscribe to the language and assumptions underlying such ‘scientificity’? If so, how does this affect the choices made in gathering, processing, analysing, and disseminating the outcomes of digital humanities research? In particular, is there a need to rethink the forms and formats of publishing scholarly work in order to enable the rigorous scrutiny and replicability of research outcomes?

An examination of the critical resources and internet capabilities for leveraging global performance in international entrepreneurial firms

This PhD research investigates the critical resources and Internet capabilities utilized by firms for leveraging global performance in entrepreneurial firms. Firm resources have been identified as important firm assets, which contribute to the firm's competitive global position. The Internet is a critical resource for a new generation of small and medium sized enterprise (SME) in pursuing international opportunities. By facilitating international business, the Internet has the ability to increase the quality and speed of communications, lower transaction costs, and facilitate the development of networks. Despite the increasing numbers of firms utilizing the Internet to pursue international opportunities, limited research remains. Adopting multiple case study methodology and structural equation modelling, the research identified the firm-level resources, which coincide with capabilities in a model predicting how international performance in firms is achieved.

Condition monitoring and fault diagnosis of diesel engines using instantaneous angular speed analysis

Continuous monitoring of diesel engine performance is critical for early detection of fault developments in an engine before they materialize into a functional failure. Instantaneous crank angular speed (IAS) analysis is one of a few nonintrusive condition monitoring techniques that can be utilized for such a task. Furthermore, the technique is more suitable for mass industry deployments than other non-intrusive methods such as vibration and acoustic emission techniques due to the low instrumentation cost, smaller data size and robust signal clarity since IAS is not affected by the engine operation noise and noise from the surrounding environment. A combination of IAS and order analysis was employed in this experimental study and the major order component of the IAS spectrum was used for engine loading estimation and fault diagnosis of a four-stroke four-cylinder diesel engine. It was shown that IAS analysis can provide useful information about engine speed variation caused by changing piston momentum and crankshaft acceleration during the engine combustion process. It was also found that the major order component of the IAS spectra directly associated with the engine firing frequency (at twice the mean shaft rotating speed) can be utilized to estimate engine loading condition regardless of whether the engine is operating at healthy condition or with faults. The amplitude of this order component follows a distinctive exponential curve as the loading condition changes. A mathematical relationship was then established in the paper to estimate the engine power output based on the amplitude of this order component of the IAS spectrum. It was further illustrated that IAS technique can be employed for the detection of a simulated exhaust valve fault in this study.

Experimental evidences in bearing diagnostics for traction system of high speed trains

Rolling element bearings are the most critical components in the traction system of high speed trains. Monitoring their integrity is a fundamental operation in order to avoid catastrophic failures and to implement effective condition based maintenance strategies. Generally, diagnostics of rolling element bearings is usually performed by analyzing vibration signals measured by accelerometers placed in the proximity of the bearing under investigation. Several papers have been published on this subject in the last two decades, mainly devoted to the development and assessment of signal processing techniques for diagnostics. The experimental validation of such techniques has been traditionally performed by means of laboratory tests on artificially damaged bearings, while their actual effectiveness in specific industrial applications, particularly in rail industry, remains scarcely investigated. This paper is aimed at filling this knowledge gap, by addressing the diagnostics of bearings taken from the service after a long term operation on the traction system of a high speed train. Moreover, in order to test the effectiveness of the diagnostic procedures in the environmental conditions peculiar to the rail application, a specific test-rig has been built, consisting of a complete full-scale train traction system, able to reproduce the effects of wheeltrack interaction and bogie-wheelset dynamics. The results of the experimental campaign show that suitable signal processing techniques are able to diagnose bearing failures even in this harsh and noisy application. Moreover, the most suitable location of the sensors on the traction system is proposed, in order to limit their number.

A new look at the restrictions on the speed and magnitude of train loads for bridge management

In current bridge management systems (BMSs), load and speed restrictions are applied on unhealthy bridges to keep the structure safe and serviceable for as long as possible. But the question is, whether applying these restrictions will always decrease the internal forces in critical components of the bridge and enhance the safety of the unhealthy bridges. To find the answer, this paper for the first time in literature, looks into the design aspects through studying the changes in demand by capacity ratios of the critical components of a bridge under the train loads. For this purpose, a structural model of a simply supported bridge, whose dynamic behaviour is similar to a group of real railway bridges, is developed. Demand by capacity ratios of the critical components of the bridge are calculated, to identify their sensitivity to increase of speed and magnitude of live load. The outcomes of this study are very significant as they show that, on the contrary to what is expected, by applying restriction on speed, the demand by capacity ratio of components may increase and make the bridge unsafe for carrying live load. Suggestions are made to solve the problem.

Speeding through roadworks: Understanding driver speed profiles and ways to reduce speeding

Poor compliance with speed limits is a serious safety concern at roadworks. While considerable research has been undertaken worldwide to understand drivers’ speeding behaviour at roadworks and to identify treatments for improving compliance with speed limits, little is known about the speeding behaviour of drivers at Australian roadworks and how their compliance rates with speed limits could be improved. This paper presents findings from two Queensland studies targeted at 1) examining drivers’ speed profiles at three long-term roadwork sites, and 2) understanding the effectiveness of speed control treatments at roadworks. The first study analysed driver speeds at various locations in the sites using a Tobit regression model. Results show that the probability of speeding was higher for light vehicles and their followers, for leaders of platoons with larger front gaps, during late afternoon and early morning, when higher proportions of surrounding vehicles were speeding, and at the upstream of work areas. The second study provided a comprehensive understanding of the effectiveness of various speed control treatments used at roadworks by undertaking a critical review of the literature. Results showed that enforcement has the greatest effects on reducing speeds among all treatments, while the roadwork signage and information-related treatments have small to moderate effects on speed reduction. Findings from the studies have potential for designing programs to effectively improve speed limit compliance at Australian roadworks.

Influence of road traffic environment and mobile phone distraction on the speed selection behaviour of young drivers

Travel speed is one of the most critical parameters for road safety; the evidence suggests that increased vehicle speed is associated with higher crash risk and injury severity. Both naturalistic and simulator studies have reported that drivers distracted by a mobile phone select a lower driving speed. Speed decrements have been argued to be a risk compensatory behaviour of distracted drivers. Nonetheless, the extent and circumstances of the speed change among distracted drivers are still not known very well. As such, the primary objective of this study was to investigate patterns of speed variation in relation to contextual factors and distraction. Using the CARRS-Q high-fidelity Advanced Driving Simulator, the speed selection behaviour of 32 drivers aged 18-26 years was examined in two phone conditions: baseline (no phone conversation) and handheld phone operation. The simulator driving route contained five different types of road traffic complexities, including one road section with a horizontal S curve, one horizontal S curve with adjacent traffic, one straight segment of suburban road without traffic, one straight segment of suburban road with traffic interactions, and one road segment in a city environment. Speed deviations from the posted speed limit were analysed using Ward’s Hierarchical Clustering method to identify the effects of road traffic environment and cognitive distraction. The speed deviations along curved road sections formed two different clusters for the two phone conditions, implying that distracted drivers adopt a different strategy for selecting driving speed in a complex driving situation. In particular, distracted drivers selected a lower speed while driving along a horizontal curve. The speed deviation along the city road segment and other straight road segments grouped into a different cluster, and the deviations were not significantly different across phone conditions, suggesting a negligible effect of distraction on speed selection along these road sections. Future research should focus on developing a risk compensation model to explain the relationship between road traffic complexity and distraction.