Organizational, direct support, and general support maintenance repairs parts and special tools lists (including depot maintenance repair parts and special tools) for receiving set, countermeasures AN/ALQ-133 (NSN 5865-00-134-2601).

"December 1978."

Simple home repairs...inside.

"November 1979"--T.p. verso.

Repairs and utilities; grounds maintenance and land management.

Bibliography: p. 137-139.

Repairs and utilities : refrigeration, air conditioning, mechanical ventilation, and evaporative cooling.

Mode of access: Internet.

Simple home repairs, outside.

Issued Jan. 1978.

Optimal preventive maintenance of leased equipment with corrective minimal repairs

For leased equipment, the lessor carries out the maintenance of the equipment. Usually, the contract of lease specifies the penalty for equipment failures and for repairs not being carried out within specified time limits. This implies that optimal preventive maintenance policies must take these penalty costs into account and properly traded against the cost of preventive maintenance actions. The costs associated with failures are high as unplanned corrective maintenance actions are costly and the resulting penalties due to lease contract terms being violated. The paper develops a model to determine the optimal parameters of a preventive maintenance policy that takes into account all these costs to minimize the total expected cost to the lessor for new item lease. The parameters of the policy are (i) the number of preventive maintenance actions to be carried out over the lease period, (ii) the time instants for such actions, and (iii) the level of action. (c) 2005 Elsevier B.V. All rights reserved.

Dimension stone for building facades: methodology for structural design

The importance of a careful selection of rocks used in building facade cladding is highlighted. A simple and viable methodology for the structural detailing of dimension stones and the verification of the global performance is presented based on a Strap software simulation. The results obtained proved the applicability of the proposed structural dimensioning methodology which represents an excellent simple tool for dimensioning rock slabs used for building facade cladding. The Strap software satisfactorily simulated the structural conditions of the stone slabs under the studied conditions, allowing the determination of alternative slab dimensions and the verification of the cladding strength at the support.

Influence of EVA and acrylate polymers on some mechanical properties of cementitious repair mortars

In repair works of reinforced concrete, patch repairs tend to crack in the interfacial zone between the mortar and the old concrete. This occurs basically due to the high degree of restriction that acts on a patch repair. For this reason, the technology of patch repair needs to be the subject of a discussion involving professionals who work with projects, construction maintenance and mix proportioning of repair mortars. In the present work, a study is presented on the benefits that the ethylene vinyl acetate copolymer (EVA) and acrylate polymers can provide in the mix proportioning of a repair mortar with respect to compressive, tensile and direct-shear bond strength. The results indicated that the increase in bond strength and the reduction in the influence of the deficiency in Curing conditioning are the main contributions offered by the polymers studied here. (C) 2009 Elsevier, Ltd. All rights reserved.

Debris flow affecting the Cubatauo Oil Refinery, Brazil

On February 6, 1994, a large debris flow developed because of intense rains in a 800-m-high mountain range called Serra do Cubatao, the local name for the Serra do Mar, located along the coast of the state of Sao Paulo, Brazil. It affected the Presidente Bernardes Refinery, owned by Petrobras, in Cubatao. The damages amounted to about US $40 million because of the muck cleaning, repairs, and 3-week interruption of the operations. This prompted Petrobras to conduct studies, carried out by the authors, to develop protection works, which were done at a cost of approximately US $12 million. The paper describes the studies conducted on debris flow mechanics. A new criteria to define rainfall intensities that trigger debris flows is presented, as well as a correlation of slipped area with soil porosity and rain intensity. Also presented are (a) an actual grain size distribution of a deposited material, determined by laboratory and a large-scale field test, and (b) the size distribution of large boulders along the river bed. Based on theory, empirical experience and back-analysis of the events, the main parameters as the front velocity, the peak discharge and the volume of the transported sediments were determined in a rational basis for the design of the protection works. Finally, the paper describes the set of the protection works built, emphasizing their concept and function. They also included some low-cost innovative works.

Thermodynamic information system for diagnosis and prognosis of power plant operation condition

A thermodynamic information system for diagnosis and prognosis of an existing power plant was developed. The system is based on an analytic approach that informs the current thermodynamic condition of all cycle components, as well as the improvement that can be obtained in the cycle performance by the elimination of the discovered anomalies. The effects induced by components anomalies and repairs in other components efficiency, which have proven to be one of the main drawbacks in the diagnosis and prognosis analyses, are taken into consideration owing to the use of performance curves and corrected performance curves together with the thermodynamic data collected from the distributed control system. The approach used to develop the system is explained, the system implementation in a real gas turbine cogeneration combined cycle is described and the results are discussed. (C) 2011 Elsevier Ltd. All rights reserved.

Two times three little pigs: Dysfluency, cognitive complexity and autism

This paper presents an analysis of dysfluencies in two oral tellings of a familiar children's story by a young boy with autism. Thurber & Tager-Flusberg (1993) postulate a lower degree of cognitive and communicative investment to explain a lower frequency of non-grammatical pauses observed in elicited narratives of children with autism in comparison to typically developing and intellectually disabled controls. we also found a very low frequency of non-grammatical pauses in our data, but indications of high engagement and cognitive and communicative investment. We point to a wider range of disfluencies as indicators of cognitive load, and show that the kind and location of dysfluencies produced may reveal which aspects of the narrative task are creating the greatest cognitive demand: here, mental state ascription, perspectivization, and adherence to story schema. This paper thus generates analytical options and hypotheses that can be explored further in a larger population of children with autism and typically developing controls.

Pole detail, PNG Coffee Industry Board Office and Warehouse, Goroka

Detailed view of poles used in construction. Poles were spliced in their length with steel bars (like 3 pin plugs) and these joints were restrained from splitting with steel strap belts. The belts were tightened with opposing wedges like the old Greene & Greene wrought iron detail.

A servicing strategy for items sold under warranty

When repairable items sold under warranty fail, the rectification action taken by the manufacturer can be either a repair or a replacement, In this paper a new repair-replacement strategy is proposed for the manufacturer when the items are sold with a non-renewing free replacement warranty policy. The strategy involves splitting the warranty period into two intervals where only repairs are carried out, separated by a third interval with at most one replacement.

Aplicação das ferramentas lean: caso de estudo

Este trabalho tem como objectivo apresentar as ferramentas do Lean Thinking e realizar um estudo de caso numa organização em que este sistema é utilizado. Numa primeira fase do trabalho será feito uma análise bibliográfica sobre o ―Lean Thinking”, que consiste num sistema de negócios, uma forma de especificar valor e delinear a melhor sequência de acções que criam valor. Em seguida, será realizado um estudo de caso numa Empresa – Divisão de Motores – no ramo da aeronáutica com uma longa e conceituada tradição com o objectivo de reduzir o TAT (turnaround time – tempo de resposta), ou seja, o tempo desde a entrada de um motor na divisão até à entrega ao cliente. Primeiramente, analisando as falhas existentes em todo o processo do motor, isto é, a análise de tempos de reparação de peças à desmontagem do motor que têm que estar disponíveis à montagem do mesmo, peças que são requisitadas a outros departamentos da Empresa e as mesmas não estão disponíveis quando são precisas passando pelo layout da divisão. Por fim, fazer uma análise dos resultados até então alcançados na divisão de Motores e aplicar as ferramentas do ―Lean Thinking‖ com o objectivo da implementação. É importante referir que a implementação bem-sucedida requer, em primeiro lugar e acima de tudo, um firme compromisso da administração com uma completa adesão à cultura da procura e eliminação de desperdício. Para concluir o trabalho, destaca-se a importância deste sistema e quais são as melhorias que se podem conseguir com a sua implantação.