Comparative analysis of the volatile fraction from Annona cherimola Mill. cultivars by solid-phase microextraction and gas chromatography–quadrupole mass spectrometry detection

The analysis of volatile compounds in Funchal, Madeira, Mateus and Perry Vidal cultivars of Annona cherimola Mill. (cherimoya) was carried out by headspace solid-phase microextraction (HS-SPME) combined with gas chromatography–quadrupole mass spectrometry detection (GC–qMSD). HS-SPME technique was optimized in terms of fibre selection, extraction time, extraction temperature and sample amount to reach the best extraction efficiency. The best result was obtained with 2 g of sample, using a divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fibre for 30 min at 30 °C under constant magnetic stirring (800 rpm). After optimization of the extraction methodology, all the cherimoya samples were analysed with the best conditions that allowed to identify about 60 volatile compounds. The major compounds identified in the four cherimoya cultivars were methyl butanoate, butyl butanoate, 3-methylbutyl butanoate, 3-methylbutyl 3-methylbutanoate and 5-hydroxymethyl-2-furfural. These compounds represent 69.08 ± 5.22%, 56.56 ± 15.36%, 56.69 ± 9.28% and 71.82 ± 1.29% of the total volatiles for Funchal, Madeira, Mateus and Perry Vidal cultivars, respectively. This study showed that each cherimoya cultivars have 40 common compounds, corresponding to different chemical families, namely terpenes, esters, alcohols, fatty acids and carbonyl compounds and using PCA, the volatile composition in terms of average peak areas, provided a suitable tool to differentiate among the cherimoya cultivars.

Potentialities of two solventless extraction approaches—Stir bar sorptive extraction and headspace solid-phase microextraction for determination of higher alcohol acetates, isoamyl esters and ethyl esters in wines

A stir bar sorptive extraction with liquid desorption followed by large volume injection coupled to gas chromatography–quadrupole mass spectrometry (SBSE-LD/LVI-GC–qMS) was evaluated for the simultaneous determination of higher alcohol acetates (HAA), isoamyl esters (IsoE) and ethyl esters (EE) of fatty acids. The method performance was assessed and compared with other solventless technique, the solid-phase microextraction (SPME) in headspace mode (HS). For both techniques, influential experimental parameters were optimised to provide sensitive and robust methods. The SBSE-LD/LVI methodology was previously optimised in terms of extraction time, influence of ethanol in the matrix, liquid desorption (LD) conditions and instrumental settings. Higher extraction efficiency was obtained using 60 min of extraction time, 10% ethanol content, n-pentane as desorption solvent, 15 min for the back-extraction period, 10 mL min−1 for the solvent vent flow rate and 10 °C for the inlet temperature. For HS-SPME, the fibre coated with 50/30 μm divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) afforded highest extraction efficiency, providing the best sensitivity for the target volatiles, particularly when the samples were extracted at 25 °C for 60 min under continuous stirring in the presence of sodium chloride (10% (w/v)). Both methodologies showed good linearity over the concentration range tested, with correlation coefficients higher than 0.984 for HS-SPME and 0.982 for SBES-LD approach, for all analytes. A good reproducibility was attained and low detection limits were achieved using both SBSE-LD (0.03–28.96 μg L−1) and HS-SPME (0.02–20.29 μg L−1) methodologies. The quantification limits for SBSE-LD approach ranging from 0.11 to 96.56 μg L−and from 0.06 to 67.63 μg L−1 for HS-SPME. Using the HS-SPME approach an average recovery of about 70% was obtained whilst by using SBSE-LD obtained average recovery were close to 80%. The analytical and procedural advantages and disadvantages of these two methods have been compared. Both analytical methods were used to determine the HAA, IsoE and EE fatty acids content in “Terras Madeirenses” table wines. A total of 16 esters were identified and quantified from the wine extracts by HS-SPME whereas by SBSE-LD technique were found 25 esters which include 2 higher alcohol acetates, 4 isoamyl esters and 19 ethyl esters of fatty acids. Generally SBSE-LD provided higher sensitivity with decreased analysis time.

Cell adhesion and growth on surfaces modified by plasma and ion implantation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Optimization of in situ derivatization SPME by experimental design for GC-MS multi-residue analysis of pharmaceutical drugs in wastewater

This paper presents the development of a procedure, which enables the analysis of nine pharmaceutical drugs in wastewater using gas chromatography-mass spectrometry (GC-MS) associated with solid-phase microextraction (SPME) for the sample preparation. Experimental design was applied to optimize the in situ derivatization and the SPME extraction conditions. Ethyl chloroformate (ECF) was employed as derivatizing agent and polydimethylsiloxane-divinylbenzene (PDMS-DVB) as the SPME fiber coating. A fractional factorial design was used to evaluate the main factors for the in situ derivatization and SPME extraction. Thereafter, a Doehlert matrix design was applied to find out the best experimental conditions. The method presented a linear range from 0.5 to 10 mu g/L, and the intraday and interday precision were lower than 16%. Applicability of the method was verified from real influent and effluent samples of a wastewater treatment plant, as well as from samples of an industry wastewater and a river.

Glass/PDMS hybrid microfluidic device integrating vertically aligned SWCNTs to ultrasensitive electrochemical determinations

This communication reports a promising platform for rapid, simple, direct, and ultrasensitive determination of serotonin. The method is related to integration of vertically aligned single-walled carbon nanotubes (SWCNTs) in electrochemical microfluidic devices. The required microfabrication protocol is simple and fast. In addition, the nanomaterial influenced remarkably the obtained limit-of-detection (LOD) values. Our system achieved a LOD of 0.2 nmol L-1 for serotonin, to the best of our knowledge one of the lowest values reported in the literature.

Untersuchung des Aggregationsverhaltens amphiphiler Diblockcopolymere in überkritischem Kohlendioxid mittels dynamischer Lichtstreuung

„Untersuchung des Aggregationsverhaltens amphiphiler Diblockcopolymere in überkritischem Kohlendioxid mittels dynamischer Lichtstreuung“ In der vorliegenden Arbeit wurde die Mizellenbildung von Diblockcopolymeren des Typs PS-b-PDMS in überkritischem Kohlendioxid (CO2,SC) mittels dynamischer Lichtstreuung (DLS) charakterisiert. Zu diesem Zweck wurden Mischungen aus den Diblockcopolymeren in CO2,SC mit Styrol als Monomer druckabhängig auf diese Fähigkeit hin untersucht. Eine Mizellenbildung konnte anhand der gemessenen hydrodynamischen Radien Rh gezeigt werden. Um eine Vergleichsmöglichkeit gegenüber den mit Styrol gefüllten Kern-Hüllen-Mizellen zu bekommen, wurde das Diblockcopolymer PS-b-PDMS (9/27) zunächst ohne Styrol auf die Fähigkeit hin untersucht ungefüllte Mizellen zu bilden. Durch Druckvariation konnte ein kritischer Mizellendruck von ca. 46,7 MPa bei einer Temperatur von 338 K im Experiment bestätigt werden, der gefundene Rh liegt bei ca. 34 nm. Dagegen setzt die Aggregation bei einer PS-b-PDMS (9/27)/Styrol/CO2,SC- Mischung bei einem wesentlich niedrigeren Druck ein. Durch Druckvariation zwischen 38 MPa und 45,7 MPa wurde eine Größenänderung der Mizellen beobachtet. Durch zeitabhängige-DLS-Messungen am gleichen System bei einem bestimmten Druck wurde ein langsames Schrumpfen der Mizellen gefunden. Um den Einfluß der Blockgröße der verwendeten Amphiphile auf die Mizellenbildung zu untersuchen wurde das System PS-b-PDMS(6/37)/Styrol/CO2,SC mit Hilfe der DLS im Bereich zwischen 39,4 MPa und 43,1 MPa untersucht. Die Druckänderung zeigte für Rh ein nahezu invariantes Verhalten, daß durch eine verlängerte PDMS-Blocklänge und eine damit verbundene Kompensation der verschiedenen Wechselwirkungskräfte zwischen Mizellenkern, -hülle und CO2,SC erklärt werden kann. Im System PS-b-PDMS(6/16)/Styrol/CO2,SC konnte experimentell mit Hilfe der DLS erst nach einer ver-änderten molaren Zusammensetzung eine Mizellenbildung ab 40 MPa ermöglicht werden. Allerdings ändert sich auch in diesem System der hydrodynamische Radius ebenfalls mit dem Druck. Je nach Druck-, Temperatur- und molarer Zusammensetzung variiert die Tendenz der Systeme, Mizellen zu bilden die eine Emulsion stabilisieren können. Für die in Dispersions-Polymerisationsreaktionen eingesetzten Diblockcopolymere bedeutet dieses Ergebnis differenzierte Applikationsmöglichkeiten. Mit den ermittelten Konzentrationsverhältnissen an Amphiphil und Monomer konnte ein Bereich gefunden werden, in dem die thermodynamischen Bedingungen für die Mizellenbildung einerseits und die Vorraussetzungen für die DLS andererseits gegeben sind.

Wet bioadhesion in tree frogs

Viele Tiere wie etwa Geckos oder Laubfrösche können mittels ihrer Haftscheiben an Oberflächen kleben. Diese Haftscheiben ermöglichen es den Tieren, sich während ihrerrnFortbewegung an Oberflächen anzuheften und wieder zu lösen unabhängig von denrnvorherrschenden Umweltbedingungen. Frösche besitzen mikro- und nanostrukturierternsowie charakteristisch geformte Haftscheiben an Finger- und Zehenenden. Ihre besonderernevolutionäre Errungenschaft, sich stark und zugleich reversibel in sowohl trockenen alsrnauch feuchten Umgebungen anzuhaften, hat die Wissenschaft zur Nachahmung und Untersuchungrndieser Strukturen inspiriert. Zum besseren Verständnis der Mechanismen vonrnAnhaftung und Loslösung bei Laubfröschen wurden weiche, elastische und mikrostrukturierternOberflächen hergestellt, indem PDMS (Polydimethylsiloxan) auf einer Siliziummaskernmit Hexagonstruktur aufgetragen und vernetzt wurde. Dadurch wurden Anordnungenrnvon hexagonalen Mikrosäulen mit spezifischen geometrischen Eigenschaften undrnunterschiedlichen Kontaktgeometrien (normale, flache Form, T-Form und konkave Formrnder Säulenenden) erhalten. Um den Einfluss der van-der-Waals, hydrodynamischen,rnKapillar-und Adhäsionskräfte zu verstehen, wurden verschiedene experimentelle Ansätzernverfolgt: Die auf eine einzelne Säule wirkenden Adhäsionskräfte wurden mittelsrnRasterkraftmikroskopie gemessen. Dazu wurden speziell hergestellte kolloidale Sensorenrnverwendet. Diese Experimente wurden sowohl mit als auch ohne Flüssigkeitsfilm auf derrnSäule durchgeführt. Die Ergebnisse zeigten den Beitrag von Kapillarkraft und direktenrnKontaktkräften zur Adhäsionskraft bei Vorliegen eines Flüssigkeitsfilms. Die Adhäsionrnfiel umso größer aus, je weniger Flüssigkeit zwischen Sensor und Säule vorhanden war.rnIm Falle einer trockenen Adhäsion zeigte die Säule mit T-Form die höchste Adhäsion. Darndie Haftscheiben der Laubfrösche weich sind, können sie dynamisch ihre Form ändern,rnwas zu einer Änderung der hydrodynamischen Kraft zwischen Scheibe und Oberflächernführt. Der Einfluss der Oberflächenverformbarkeit auf die hydrodynamische Kraft wurderndaher am Modellsystem einer Kugel untersucht, welche sich einer weichen und ebenenrnOberfläche annähert. Dieses System wurde sowohl theoretisch über die Simulation finiterrnElemente als auch experimentell über die Messung mit kolloidalen Sonden untersucht.rnSowohl experimentelle Ergebnisse als auch die Simulationen ergaben eine Abnahme derrnhydrodynamischen Kraft bei Annäherung des kolloidalen Sensors an eine weiche undrnelastische Oberfläche. Beim Entfernen der Sensors von der Oberfläche verstärkte sichrndie hydrodynamische Anziehungskraft. Die Kraft, die zur Trennung eines Partikels von einer Oberfläche in Flüssigkeit notwendig ist, ist für weiche und elastischen Oberflächenrngrößer als für harte Oberflächen. In Bezug zur Bioadhäsion bei Laubfröschen konnternfestgestellt somit festgestellt werden, dass sich der hydrodynamische Anteil zur feuchtenrnBioadhäsion aufgrund der weichen Oberfläche erhöht. Weiterhin wurde der Einflussrndes Aspektverhältnisses der Säulen auf die Reibungskraft mittels eines kolloidalen Sensorsrnuntersucht. Gestreckte Säulen zeigten dabei eine höhere Reibung im Vergleich zu.rnSäulen mit einem gestreckten Hexagon als Querschnitt.

Chemical Sensor Based on a Long-Period Fibre Grating Modified by a Functionalized Polydimethylsiloxane Coating

A chemical sensor based on a coated long-period grating has been prepared and characterized. Designer coatings based on polydimethylsiloxane were prepared by the incorporation of diphenylsiloxane and titanium cross-linker in order to provide enhanced sensitivity for a variety of key environmental pollutants and optimal refractive index of the coating. Upon microextraction of the analyte into the polymer matrix, an increase in the refractive index of the coating resulted in a change in the attenuation spectrum of the long-period grating. The grating was interrogated using ring-down detection as a means to amplify the optical loss and to gain stability against misalignment and power fluctuations. Chemical differentiation of cyclohexane and xylene was achieved and a detection limit of 300 ppm of xylene vapour was realized.

The morphology of ordered block copolymer patterns as probed by high resolution imaging

The microphase separation of block copolymer (BCP) thin films can afford a simple and cost-effective means to studying nanopattern surfaces, and especially the fabrication of nanocircuitry. However, because of complex interface effects and other complications, their 3D morphology, which is often critical for application, can be more complex than first thought. Here, we describe how emerging microscopic methods may be used to study complex BCP patterns and reveal their rich detail. These methods include helium ion microscopy (HIM) and high resolution x-section transmission electron microscopy (XTEM), and complement conventional secondary electron and atomic force microscopies (SEM and TEM). These techniques reveal that these structures are quite different to what might be expected. We illustrate the advances in the understanding of BCP thin film morphology in several systems, which result from this characterization. The systems described include symmetric, lamellar forming polystyrene-b-polymethylmethacrylate (PS-b-PMMA), cylinder forming polystyrene-b-polydimethylsiloxane (PS-b-PDMS), as well as lamellar and cylinder forming patterns of polystyrene-b-polyethylene oxide (PS-b-PEO) and polystyrene-b-poly-4-vinylpyridine (PS-b-P4VP). Each of these systems exhibits more complex arrangements than might be first thought. Finding and developing techniques whereby complex morphologies, particularly at very small dimensions, can be determined is critical to the practical use of these materials in many applications. The importance of quantifying these complex morphologies has implications for their use in integrated circuit manufacture, where they are being explored as alternative pattern forming methods to conventional UV lithography.

Chemical Sensor Based on a Long-Period Fibre Grating Modified by a Functionalized Polydimethylsiloxane Coating

A chemical sensor based on a coated long-period grating has been prepared and characterized. Designer coatings based on polydimethylsiloxane were prepared by the incorporation of diphenylsiloxane and titanium cross-linker in order to provide enhanced sensitivity for a variety of key environmental pollutants and optimal refractive index of the coating. Upon microextraction of the analyte into the polymer matrix, an increase in the refractive index of the coating resulted in a change in the attenuation spectrum of the long-period grating. The grating was interrogated using ring-down detection as a means to amplify the optical loss and to gain stability against misalignment and power fluctuations. Chemical differentiation of cyclohexane and xylene was achieved and a detection limit of 300 ppm of xylene vapour was realized.

Refractometry Studies of the Optical Properties of Polymer Films and the Development of Polymer Coated Refractive Index Sensors

Sensors for real-time monitoring of environmental contaminants are essential for protecting ecosystems and human health. Refractive index sensing is a non-selective technique that can be used to measure almost any analyte. Miniaturized refractive index sensors, such as silicon-on-insulator (SOI) microring resonators are one possible platform, but require coatings selective to the analytes of interest. A homemade prism refractometer is reported and used to characterize the interactions between polymer films and liquid or vapour-phase analytes. A camera was used to capture both Fresnel reflection and total internal reflection within the prism. For thin-films (d = 10 μm - 100 μm), interference fringes were also observed. Fourier analysis of the interferogram allowed for simultaneous extraction of the average refractive index and film thickness with accuracies of ∆n = 1-7 ×10-4 and ∆d < 3-5%. The refractive indices of 29 common organic solvents as well as aqueous solutions of sodium chloride, sucrose, ethylene glycol, glycerol, and dimethylsulfoxide were measured at λ = 1550 nm. These measurements will be useful for future calibrations of near-infrared refractive index sensors. A mathematical model is presented, where the concentration of analyte adsorbed in a film can be calculated from the refractive index and thickness changes during uptake. This model can be used with Fickian diffusion models to measure the diffusion coefficients through the bulk film and at the film-substrate interface. The diffusion of water and other organic solvents into SU-8 epoxy was explored using refractometry and the diffusion coefficient of water into SU-8 is presented. Exposure of soft baked SU-8 films to acetone, acetonitrile and methanol resulted in rapid delamination. The diffusion of volatile organic compound (VOC) vapours into polydimethylsiloxane and polydimethyl-co-polydiphenylsiloxane polymers was also studied using refractometry. Diffusion and partition coefficients are reported for several analytes. As a model system, polydimethyl-co-diphenylsiloxane films were coated onto SOI microring resonators. After the development of data acquisition software, coated devices were exposed to VOCs and the refractive index response was assessed. More studies with other polymers are required to test the viability of this platform for environmental sensing applications.

Surface acoustic wave streaming in a PDMS microfluidic system: effect of frequency and fluid geometry & A remote ultrasonic glucose sensor

This thesis describes two separate projects. The first is a theoretical and experimental investigation of surface acoustic wave streaming in microfluidics. The second is the development of a novel acoustic glucose sensor. A separate abstract is given for each here. Optimization of acoustic streaming in microfluidic channels by SAWs Surface Acoustic Waves, (SAWs) actuated on flat piezoelectric substrates constitute a convenient and versatile tool for microfluidic manipulation due to the easy and versatile interfacing with microfluidic droplets and channels. The acoustic streaming effect can be exploited to drive fast streaming and pumping of fluids in microchannels and droplets (Shilton et al. 2014; Schmid et al. 2011), as well as size dependant sorting of particles in centrifugal flows and vortices (Franke et al. 2009; Rogers et al. 2010). Although the theory describing acoustic streaming by SAWs is well understood, very little attention has been paid to the optimisation of SAW streaming by the correct selection of frequency. In this thesis a finite element simulation of the fluid streaming in a microfluidic chamber due to a SAW beam was constructed and verified against micro-PIV measurements of the fluid flow in a fabricated device. It was found that there is an optimum frequency that generates the fastest streaming dependent on the height and width of the chamber. It is hoped this will serve as a design tool for those who want to optimally match SAW frequency with a particular microfluidic design. An acoustic glucose sensor Diabetes mellitus is a disease characterised by an inability to properly regulate blood glucose levels. In order to keep glucose levels under control some diabetics require regular injections of insulin. Continuous monitoring of glucose has been demonstrated to improve the management of diabetes (Zick et al. 2007; Heinemann & DeVries 2014), however there is a low patient uptake of continuous glucose monitoring systems due to the invasive nature of the current technology (Ramchandani et al. 2011). In this thesis a novel way of monitoring glucose levels is proposed which would use ultrasonic waves to ‘read’ a subcutaneous glucose sensitive-implant, which is only minimally invasive. The implant is an acoustic analogy of a Bragg stack with a ‘defect’ layer that acts as the sensing layer. A numerical study was performed on how the physical changes in the sensing layer can be deduced by monitoring the reflection amplitude spectrum of ultrasonic waves reflected from the implant. Coupled modes between the skin and the sensing layer were found to be a potential source of error and drift in the measurement. It was found that by increasing the number of layers in the stack that this could be minimized. A laboratory proof of concept system was developed using a glucose sensitive hydrogel as the sensing layer. It was possible to monitor the changing thickness and speed of sound of the hydrogel due to physiological relevant changes in glucose concentration.

Comparison Of Techniques For The Isolation Of Volatiles From Cashew Apple Juice.

The aim of this study was to compare the performance of the following techniques on the isolation of volatiles of importance for the aroma/flavor of fresh cashew apple juice: dynamic headspace analysis using PorapakQ(®) as trap, solvent extraction with and without further concentration of the isolate, and solid-phase microextraction (fiber DVB/CAR/PDMS). A total of 181 compounds were identified, from which 44 were esters, 20 terpenes, 19 alcohols, 17 hydrocarbons, 15 ketones, 14 aldehydes, among others. Sensory evaluation of the gas chromatography effluents revealed esters (n = 24) and terpenes (n = 10) as the most important aroma compounds. The four techniques were efficient in isolating esters, a chemical class of high impact in the cashew aroma/flavor. However, the dynamic headspace methodology produced an isolate in which the analytes were in greater concentration, which facilitates their identification (gas chromatography-mass spectrometry) and sensory evaluation in the chromatographic effluents. Solvent extraction (dichloromethane) without further concentration of the isolate was the most efficient methodology for the isolation of terpenes. Because these two techniques also isolated in greater concentration the volatiles from other chemical classes important to the cashew aroma, such as aldehydes and alcohols, they were considered the most advantageous for the study of cashew aroma/flavor.

Design and fabrication of microcavity-array superhydrophobic surfaces

We have modeled, fabricated, and characterized superhydrophobic surfaces with a morphology formed of periodic microstructures which are cavities. This surface morphology is the inverse of that generally reported in the literature when the surface is formed of pillars or protrusions, and has the advantage that when immersed in water the confined air inside the cavities tends to expel the invading water. This differs from the case of a surface morphology formed of pillars or protrusions, for which water can penetrate irreversibly among the microstructures, necessitating complete drying of the surface in order to again recover its superhydrophobic character. We have developed a theoretical model that allows calculation of the microcavity dimensions needed to obtain superhydrophobic surfaces composed of patterns of such microcavities, and that provides estimates of the advancing and receding contact angle as a function of microcavity parameters. The model predicts that the cavity aspect ratio (depth-to-diameter ratio) can be much less than unity, indicating that the microcavities do not need to be deep in order to obtain a surface with enhanced superhydrophobic character. Specific microcavity patterns have been fabricated in polydimethylsiloxane and characterized by scanning electron microscopy, atomic force microscopy, and contact angle measurements. The measured advancing and receding contact angles are in good agreement with the predictions of the model. (C) 2010 American Institute of Physics. [doi:10.1063/1.3466979]

Rapid prototyping of polymeric electrophoresis microchips with integrated copper electrodes for contactless conductivity detection

A simple and easy approach to produce polymeric microchips with integrated copper electrodes for capacitively coupled contactless conductivity detection (CD) is described. Copper electrodes were fabricated using a printed circuit board (PCB) as an inexpensive thin-layer of metal. The electrode layout was first drawn and laser printed on a wax paper sheet. The toner layer deposited on the paper sheet was thermally transferred to the PCB surface working as a mask for wet chemical etching of the copper layer. After the etching step, the toner was removed with an acetonitrile-dampened cotton. A poly(ethylene terephthalate) (PET) film coated with a thin thermo-sensitive adhesive layer was used to laminate the PCB plate providing an insulator layer of the electrodes to perform CID measurements. Electrophoresis microchannels were fabricated in poly(dimethylsiloxane) (PDMS) by soft lithography and reversibly sealed against the PET film. These hybrid PDMS/PET chips exhibited a stable electroosmotic mobility of 4.25 +/- 0.04 x 10(-4) V cm(-2) s(-1), at pH 6.1, over fifty runs. Efficiencies ranging from 1127 to 1690 theoretical plates were obtained for inorganic cations.