Transducer for direct measurement of skin friction in hypervelocity impulse facilities

An acceleration compensated transducer was developed to enable the direct measurement of skin friction in hypervelocity impulse facilities. The gauge incorporated a measurement and acceleration element that employed direct shear of a piezoelectric ceramic. The design integrated techniques to maximize rise time and shear response while minimizing the affects of acceleration, pressure, heat transfer, and electrical interference. The arrangement resulted in a transducer natural frequency near 40 kHz. The transducer was calibrated for shear and acceleration in separate bench tests and was calibrated for pressure within an impulse facility. Uncertainty analyses identified only small experimental errors in the shear and acceleration calibration techniques. Although significant errors were revealed in the method of pressure calibration, total skin-friction measurement errors as low as +/-7-12% were established. The transducer was successfully utilized in a shock tunnel, and sample measurements are presented for flow conditions that simulate a flight Mach number near 8.

Towards a GIS-T database design and implementation for public transit planning: the case study of Dar-Es-salaam metropolitan city, Tanzania.

Dissertation submitted in partial fulfilment of the requirements for the Degree of Master of Science in Geospatial Technologies

UJI Navigation Network, Development of a pedestrian spatial network within the University Jaume I of Castellón (Spain)

Dissertation submitted in partial fulfillment of the requirements for the Degree of Master of Science in Geospatial Technologies.

Pedestrian Priority Zones in the Context of Urban Mobility and Valorization of Public Space

The second half of the XX century was marked by a great increase in the number of people living in cities. Urban agglomerations became poles of attraction for migration flows and these phenomena, coupled with growing car-ownership rates, resulted in the fact that modern transport systems are characterized by large number of users and traffic modes. The necessity to organize these complex systems and to provide space for different traffic modes changed the way cities look. Urban areas had to cope with traffic flows, and as a result nowadays typical street pattern consists of a road for motorized vehicles, a cycle lane (in some cases), pavement for pedestrians, parking and a range of crucial signage to facilitate navigation and make mobility more secure. However, this type of street organization may not be desirable in certain areas, more specifically, in the city centers. Downtown areas have always been places where economic, leisure, social and other types of facilities are concentrated, not surprisingly, they often attract large number of people and this frequently results in traffic jams, air and noise pollution, thus creating unpleasant environment. Besides, excessive traffic signage in central locations can harm the image and perception of a place, this relates in particular to historical centers with architectural heritage.

Urban design proposes for the norwegian cities

Alta is the biggest city in the country of Finnmark. The area of study, Bossekop, is situated 4km from the city centre. It has some commercial areas, offices, hotels and housing, mostly single family housing. The most important Norwegian road, E6 goes through Bossekop, there for it has a big traffic flow. The concept builds on the idea of two axis, one local leading from the local sports development area into the centre core, and one on a higher level, the E6. In Bodø, after analysing carefully the surroundings we reached the conclusion that it is posssible to conserve a lot of the green as well as offering the municipalities the chance to develop with several housing typologies. Nature should be preserved and with this connect directly the mountain to the sea, using the existing creek to make the water connection. In order to keep a big part of this land untouched, we suggest that the rest of the site can be developed quite densely in one of the areas and then continuously fading out in direction of the mountains. Finnsnes is an important communication point for the region with its good connections. In that way it is becoming a central point for commerce and leisure. The concept is based on the wish from the municipality of Lenvik to look upon the city’s connection to the surrounding sea and green areas, together with the wish to make the pedestrian access better and the car traffic lighter., and in that way improve the conditions in the city

Application of a support system to the design of wastewater treatment plants

This paper presents a case study that explores the advantages that can be derived from the use of a design support system during the design of wastewater treatment plants (WWTP). With this objective in mind a simplified but plausible WWTP design case study has been generated with KBDS, a computer-based support system that maintains a historical record of the design process. The study shows how, by employing such a historical record, it is possible to: (1) rank different design proposals responding to a design problem; (2) study the influence of changing the weight of the arguments used in the selection of the most adequate proposal; (3) take advantage of keywords to assist the designer in the search of specific items within the historical records; (4) evaluate automatically thecompliance of alternative design proposals with respect to the design objectives; (5) verify the validity of previous decisions after the modification of the current constraints or specifications; (6) re-use the design records when upgrading an existing WWTP or when designing similar facilities; (7) generate documentation of the decision making process; and (8) associate a variety of documents as annotations to any component in the design history. The paper also shows one possible future role of design support systems as they outgrow their current reactive role as repositories of historical information and start to proactively support the generation of new knowledge during the design process

Roadway Design Standards for Rural and Suburban Subdivisions Final Report, June 2007

In Iowa, there are currently no uniform design standards for rural and suburban subdivision development roadways. Without uniform design standards, many counties are unable to provide adequate guidance for public facilities, particularly roadways, to be constructed as part of a rural subdivision development. If a developer is not required to install appropriate public improvements or does not do so properly, significant liability and maintenance expenses can be expected, along with the potential for major project costs to correct the situation. Not having uniform design standards for rural and suburban subdivision development improvements in Iowa creates situations where there is potential for inconsistency and confusion. Differences in the way development standards are applied also create incentives or disincentives for developers to initiate subdivision platting in a particular county. With the wide range of standards or lack of standards for local roads in development areas, it is critical that some level of uniformity is created to address equity in development across jurisdictional lines. The standards must be effective in addressing the problem, but they must not be so excessive as to curtail development activities within a local jurisdiction. In order to address the concerns, cities and counties have to work together to identify where growth is going to be focused. Within that long-term growth area, the roadways should be constructed to urban standards to provide an easier transition to traditional urban facilities as the area is developed. Developments outside of the designated growth area should utilize a rural cross section since it is less likely to have concentrated urban development. The developers should be required to develop roadways that are designed for a minimum life of 40 years, and the county should accept dedication of the roadway and be responsible for its maintenance.

Effectiveness of Electrochemical Chloride Extraction for the Iowa Avenue Pedestrian Bridge, TR-499, 2005

The main objective of this study is to determine the effectiveness of the Electrochemical Chloride Extraction (ECE) technique on a bridge deck with very high concentrations of chloride. This ECE technique was used during the summer of 2003 to reverse the effects of corrosion, which had occurred in the reinforcing steel embedded in the pedestrian bridge deck over Highway 6, along Iowa Avenue, in Iowa City, Iowa, USA. First, the half cell potential was measured to determine the existing corrosion level in the field. The half-cell potential values were in the indecisive range of corrosion (between -200 mV and -350 mV). The ECE technique was then applied to remove the chloride from the bridge deck. The chloride content in the deck was significantly reduced from 25 lb/cy to 4.96 lb/cy in 8 weeks. Concrete cores obtained from the deck were measured for their compressive strengths and there was no reduction in strength due to the ECE technique. Laboratory tests were also performed to demonstrate the effectiveness of the ECE process. In order to simulate the corrosion in the bridge deck, two reinforced slabs and 12 reinforced beams were prepared. First, the half-cell potentials were measured from the test specimens and they all ranged below -200 mV. Upon introduction of 3% salt solution, the potential reached up to -500 mV. This potential was maintained while a salt solution was being added for six months. The ECE technique was then applied to the test specimens in order to remove the chloride from them. Half-cell potential was measured to determine if the ECE technique can effectively reduce the level of corrosion.

Design of axial-flux permanent-magnet low-speed machines and performance comparison between radial-flux and axial-flux machines

This thesis presents an alternative approach to the analytical design of surface-mounted axialflux permanent-magnet machines. Emphasis has been placed on the design of axial-flux machines with a one-rotor-two-stators configuration. The design model developed in this study incorporates facilities to include both the electromagnetic design and thermal design of the machine as well as to take into consideration the complexity of the permanent-magnet shapes, which is a typical requirement for the design of high-performance permanent-magnet motors. A prototype machine with rated 5 kW output power at 300 min-1 rotation speed has been designed and constructed for the purposesof ascertaining the results obtained from the analytical design model. A comparative study of low-speed axial-flux and low-speed radial-flux permanent-magnet machines is presented. The comparative study concentrates on 55 kW machines with rotation speeds 150 min-1, 300 min-1 and 600 min-1 and is based on calculated designs. A novel comparison method is introduced. The method takes into account the mechanical constraints of the machine and enables comparison of the designed machines, with respect to the volume, efficiency and cost aspects of each machine. It is shown that an axial-flux permanent-magnet machine with one-rotor-two-stators configuration has generally a weaker efficiency than a radial-flux permanent-magnet machine if for all designs the same electric loading, air-gap flux density and current density have been applied. On the other hand, axial-flux machines are usually smaller in volume, especially when compared to radial-flux machines for which the length ratio (axial length of stator stack vs. air-gap diameter)is below 0.5. The comparison results show also that radial-flux machines with alow number of pole pairs, p < 4, outperform the corresponding axial-flux machines.

Control of ammonia emissions in naturally ventilated dairy cattle facilities in Portugal

We conducted a study of the processes associated to NH3 emission in naturally ventilated dairy cattle facilities, having described factors that regulate NH3 emission, as well as methodologies for measuring these emissions at these facilities. Appropriate techniques to mitigate NH3 emission in facilities located in regions with warm climates were also identified. The most effective mitigation techniques with simple implementation include strategies associated to: (i) installation design and flooring, which lead to reduced emissions, (ii) excreta pre-excretion, namely the use of diets with optimized crude protein content and increased milk production at farm level; and (iii) excreta post-excretion, particularly by changing the conditions of environmental monitoring within the premises, practice introduction or additive application in the management of excreta deposited on floors.

Water chemistry management for future large experimental facilities

The thesis focuses on the water chemistry of the experimental test facilities and their reference VVER reactors. The main objective of the thesis is to provide recommendations for water chemistry management for laboratory facilities (VEERA, PACTEL) simulating the VVERs and for the large future facilities of the Lappeenranta University of Technology. In the beginning, the concept of nuclear power generation and the applicability of the nuclear power usage is discussed. Next, different water chemistry and water purification systems in primary and secondary circuits currently used at the power plant have been outlined. Also the construction geometry and design of test facilities PACTEL and VEERA, as well as the operation principles of their main equipment has been described. Finally, the appropriate water chemistry and water treatment system have been proposed for the existing and future experimental facilities of LUT.

The effectiveness of interpretive methods in informal educational facilities : an experimental study with reference to marine parks

Interpretation has been used in many tourism sectors as a technique in achieving building hannony between resources and human needs. The objectives of this study are to identify the types of the interpretive methods used, and to evaluate their effectiveness, in marine parks. This study reviews the design principles of an effective interpretation for marine wildlife tourism, and adopts Drams' five design principles (1997) into a conceptual framework. Enjoyment increase, knowledge gain, attitude and intention change, and behaviour modification were used as key indicators in the assessment of the interpretive effectiveness of the Vancouver Aquarium (VA) and Marineland Canada (MC). Since on-site research is unavailable, a virtual tour is created to represent the interpretive experiences in the two study sites. Self-administered questionnaires are used to measure responses. Through comparing responses to the questionnaires (pre-, post-virtual tours and follow-up), this study found that interpretation increased enjoyment and added to respondents' knowledge. Although the changes in attitudes and intentions are not significant, the findings indicate that attitude and intention changes did occur as a result of interpretation, but only to a limited extent. Overall results suggest that more techniques should be added to enhance the effectiveness of the interpretation in marine parks or self-guiding tours, and with careful design, virtual tours are the innovative interpretation techniques for marine parks or informal educational facilities.

Designing Meat Packing Plant Handling Facilities for Cattle and Hogs

The focus is on design, more specifically, "animal handling facilities which are labor saving and reduce bruise losses". The article studies: Unloading Chutes, Stockyard Design, Hog Plant Stockyard, General Purpose Small Stockyard, Beef Stockyard, Cattle Crowding Pens, Hog Crowding Pens, Slopes in Chutes and Crowding Pens, Single File Chutes General Recommendations, Single File Chutes for Cattle, Slaughter Restrainers,

Dipping is Easy...With Right Vat Design

The article discusses dipping vats and three basic types of dipping systems: Jump in Vat, Hydraulic Cage Vat, and the Box Sprayer.

Pointers on Design and Operation of Cattle Restrainer Systems

The article discusses the importance of design and the people who run handling systems.