Estimation of water retention curve from mercury intrusion porosimetry and van Genuchten model

The water retention curve (WRC) is a hydraulic characteristic of concrete required for advanced modeling of water (and thus solute) transport in variably saturated, heterogeneous concrete. Unfortunately, determination by a direct experimental method (for example, measuring equilibrium moisture levels of large samples stored in constant humidity cells) is a lengthy process, taking over 2 years for large samples. A surrogate approach is presented in which the WRC is conveniently estimated from mercury intrusion porosimetry (MIP) and validated by water sorption isotherms: The well-known Barrett, Joyner and Halenda (BJH) method of estimating the pore size distribution (PSD) from the water sorption isotherm is shown to complement the PSD derived from conventional MIP. This provides a basis for predicting the complete WRC from MIP data alone. The van Genuchten equation is used to model the combined water sorption and MIP results. It is a convenient tool for describing water retention characteristics over the full moisture content range. The van Genuchten parameter estimation based solely on MIP is shown to give a satisfactory approximation to the WRC, with a simple restriction on one. of the parameters.

Variação da composição nutricional e propriedades de cenouras durante a secagem

Este trabalho teve como objetivo a determinação das propriedades da cenoura (Daucus carota L.), da variedade Nantes, antes, durante e após a secagem por convecção a três temperaturas diferentes (50, 60 e 70 ºC).De forma a verificar as alterações ao nível de diferentes propriedades, tais como: propriedades químicas (humidade, proteínas, fibras, cinzas, açúcares e 'aw') propriedades físicas (textura, cor, porosidade e densidade) e propriedades termofísicas (calor específico, condutividade térmica, difusividade e entalpia). Dos resultados obtidos foi possível concluir que a temperatura de secagem de 70 º C foi a que mais afetou as propriedades químicas analisadas, tais como a humidade, proteínas e açúcares redutores, onde estes sofreram uma diminuição ao longo das secagens. A 'aw' também apresentou uma diminuição ao longo das secagens, onde apresentou um menor valor na secagem a 70 ºC, tendo passado de 0,97 para 0,69, enquanto as temperaturas de 50 ºC e 60 ºC apresentaram um valor final igual, de 0,74. No que diz respeito às propriedades físicas, verificou-se que em relação à textura registaram-se evoluções semelhantes em termos de dureza, mastigabilidade e gomosidade, na medida em que sofreram uma acentuada diminuição nas primeiras horas de secagem, e a temperatura de 70 ºC foi a que mais afetou estas propriedades. No caso da cor a temperatura de 60 ºC foi a que provocou uma maior diferença de cor, a qual ao longo da secagem esta foi aumentando. A porosidade sofreu um aumento com as secagens devido à diminuição da humidade, no entanto a temperatura de 70 ºC foi a que obteve uma menor porosidade, e as temperaturas de 50 ºC e 60 ºC apresentaram valores de porosidade semelhantes. As propriedades termofísicas registaram uma diminuição ao longo da secagem, onde o calor específico sofreu uma maior diminuição com a temperatura de 70 ºC, passando de 3,90 kJ/kg.K para 1,99 kJ/kg.K. A condutividade térmica também sofreu uma maior diminuição com a temperatura de 70 ºC, diminuindo de 0,5243 W/m.K para 0,2782 W/m.K. A difusividade foi de igual forma afetada pela temperatura de 70 ºC, tendo diminuído de 1,50×10-7 m2/s para 1,06×10-7 m2/s. No caso da entalpia, esta sofreu uma maior diminuição com a temperatura de 50 ºC, passando de 233 J/kg para 96,7 J/kg. As isotérmicas de sorção foram ajustadas ao modelo de GAB, onde se verificou que apesar de algumas oscilações a quantidade de água sorvida a uma determinada aw, aumentou com a diminuição da temperatura.Os dados da cinética de secagem foram tratados e ajustados de acordo com três modelos: Page, Henderson & Pabis e Logarítmico, tendo-se verificado que o modelo de Page foi o que mostrou melhor descrever os processos em estudo, enquanto o pior modelo para descrever a cinética de secagem foi o Logarítmico.

Atrazine sorption in soil treated with biochar.

Biochar has been used worldwide as soil amendment. Due to the high sorption capacity of organic compounds by charcoal in general, the use of biochar can change the soil sorptive properties, that could result in a environmental protective strategy in one hand and/or in need of higher pesticides doses in another hand. However no data in the literature is available about the long term effect of biochar application in the sorptive properties of the soil, even studies about the sorptive properties of soil treated with biochar are scarce, the few available papers are with pure biochar. This unprecedented work, evaluating the sorption of atrazine in a clayed soil treated with biochar, under experimental field conditions, evaluated the sorption isotherms one and three years after the single biochar application (16 Mg ha-1 of biochar). One year after the biochar application the Kf was two times higher for the biochar amended soil than for the control one (without biochar). This effect decreases after three years from the application, but it is even significantly higher (50% higher) than the control treatment.

Adsorption kinetic, thermodynamic and desorption studies of phosphate onto hydrous niobium oxide prepared by reverse microemulsion method

A type of Nb(2)O(5)center dot 3H(2)O was synthesized and its phosphate removal potential was investigated in this study. The kinetic study, adsorption isotherm, pH effect, thermodynamic study and desorption were examined in batch experiments. The kinetic process was described by a pseudo-second-order rate model very well. The phosphate adsorption tended to increase with a decrease of pH. The adsorption data fitted well to the Langmuir model with which the maximum P adsorption capacity was estimated to be 18.36 mg-Pg(-1). The peak appearing at 1050 cm(-1) in IR spectra after adsorption was attributed to the bending vibration of adsorbed phosphate. The positive values of both Delta H degrees and Delta S degrees suggest an endothermic reaction and increase in randomness at the solid-liquid interface during the adsorption. Delta G degrees values obtained were negative indicating a spontaneous adsorption process. A phosphate desorbability of approximately 68% was observed with water at pH 12, which indicated a relatively strong bonding between the adsorbed phosphate and the sorptive sites on the surface of the adsorbent. The immobilization of phosphate probably occurs by the mechanisms of ion exchange and physicochemical attraction. Due to its high adsorption capacity, this type of hydrous niobium oxide has the potential for application to control phosphorus pollution.

Adsorption of Ni(2+), Zn(2+) and Pb(2+) onto dry biomass of Arthrospira (Spirulina) platensis and Chlorella vulgaris. I. Single metal systems

Adsorption of Ni(2+), Zn(2+) or Pb(2+) by dry biomass of Arthrospira (Spirulina) platensis and Chlorella vulgaris was studied as a function of contact time and initial metal concentration. The zero point of charge calculated for these biosorbents (pH(zpc) 4.0 and 3.4, respectively) and additional pH tests suggested the use of pH in the range 5.0-5.5 for the experiments. The equilibrium isotherms were evaluated in terms of maximum sorption capacity and sorption affinity. The pseudo first and second order kinetic models were considered to interpret the experimental data, and the latter best described the adsorption system. Both the Freundlich and Langmuir models were shown to well describe the sorption isotherms, thus suggesting an intermediate mono/multilayer sorption mechanism. Compared to A. platensis (q(e) = 0.354, 0.495 and 0.508 mmol g(-1) for Ni(2+), Pb(2)+ and Zn(2+), respectively), C. vulgaris behaved as a better biosorbent because of higher equilibrium sorption capacity (q(e) = 0.499, 0.634 and 0.664 mmol g(-1), respectively). The removal efficiency decreased with increasing metal concentration, pointing out a passive adsorption process involving the active sites on the surface of the biomasses. The FT-IR spectroscopy evidenced that ions removal occurred mainly by interaction between metal and carboxylate groups present on both the cell walls. (C) 2011 Elsevier B.V. All rights reserved.

Preparação de biofilmes a partir de resíduos da indústria de curtumes

A indústria dos curtumes é uma das indústrias mais antigas e tradicionais de Portugal e é também uma das mais poluentes. Esta indústria produz muitos resíduos sólidos, entre os quais, está o pelo de bovino. A valorização deste resíduo permite reduzir o impacto ambiental e aumentar a eco-eficiência da indústria dos curtumes. O pelo de bovino, rico em queratina, é um bom candidato para a produção de biofilmes. O objetivo deste trabalho foi a valorização de um resíduo de indústria de curtume (pelo de bovino) através da produção de filmes à base de queratina por termocompressão. Foi estudada a melhor formulação e as condições operatórias mais favoráveis com a finalidade de melhorar as propriedades mecânicas dos filmes. O trabalho realizado durante este projeto dividiu-se em 5 partes: preparação do material, caracterização do material, seleção do pré-tratamento, produção de filmes e caracterização dos filmes. Foram produzidos filmes para a seleção do pré-tratamento e para a respetiva caracterização. Os pré-tratamentos testados foram: tratamento com detergente, tratamento com detergente e sulfureto de sódio e, tratamento com detergente e éter de petróleo. O pré-tratamento selecionado foi o tratamento com detergente. Para a produção de filmes para a posterior caracterização, foram escolhidos 4 conjuntos de condições operatórias diferentes: 160 oC – 147 kN – 8 min – 30% glicerol; 160 oC – 147 kN – 12 min – 30% glicerol; 160 oC – 147 kN – 8 min – 40% glicerol; 160 oC – 147 kN – 12 min – 40% glicerol; identificados como Conjuntos A, B, C e D, respetivamente. Na caracterização dos filmes foram analisados vários parâmetros, nomeadamente a espessura, a permeabilidade ao vapor de água ao vapor de água, as isotérmicas de sorção, a cor, a solubilidade e as propriedades mecânicas. Também foram feitas as análises de calorimetria diferencial de varrimento (DSC) e microscopia eletrónica de varrimento (SEM). Concluiu-se que os filmes do conjunto A (160 oC – 147 kN – 8 min – 30% glicerol) tiveram um melhor desempenho apresentando espessuras médias de 0,25 0,02 mm, permeabilidade ao vapor de água ao vapor de água igual a 1,20 x 10-8 6,79 x 10-10 g/(m.s.Pa), solubilidade igual a 27,9 0,4 %, tensão de rutura média igual a 9,23 1,19 N/mm2, deformação na rutura média igual a 1,9 0,2 % e módulo de elasticidade médio igual a 554 26 N/mm2. Verificou-se um bom ajuste do modelo de GAB aos resultados experimentais. A análise DSC indicou uma temperatura de fusão aos 170 ºC para a mistura de pelo e glicerol que não se verificou nos filmes formados e indicou a temperatura de degradação do material por volta dos 240-250 ºC. A análise SEM mostrou que os filmes não estão totalmente fundidos e provou a irregularidade da superfície dos mesmos. Provou-se que é possível a produção de filmes de pelo bovino sendo ainda necessário melhorar o processo de mistura do pelo com o glicerol.

The release of silicon from amorphous silica and rice straw in Sri Lankan soils

Silicon release from rice straw and amorphous silica when shaken in solution with five Sri Lankan soils was studied indirectly using sorption isotherms and changes in concentration and directly using straw in dialysis bags examined using electron microscopy. The aim was to further our understanding of the processes and factors affecting the release of straw-Si in soils and its availability to rice. The soils (alfisols and ultisols) shaken with 0.1 M NaCl (5 g per 125 mL for 250 days) produced concentrations of 1 - 4 mg L-1 of monosilicic acid-Si. Amorphous silica added to these suspensions (36.5 mg, containing 17 mg Si) raised the concentrations to 20 - 40 mg L-1, and added rice straw (0.5 g, containing 17 mg Si) gave 10 - 25 mg L-1. Sorption isotherms (7 days equilibrations) were used to calculate from the concentrations the amounts of Si released ( 24 - 38% and 8 - 21%, respectively). Both materials gave about 40 mg L-1 of monosilicic acid-Si plus 30 mg L-1 of disilicic acid-Si when shaken in solution alone (5 g per 125 mL). Straw in dialysis bags ( 0.5 g per 25 mL in 0.1 M NaCl) was shaken in soil suspension ( 5 g per 100 mL) for 60 days. Similar concentrations and releases were measured to those obtained above. About one fifth of the mass of straw was lost by decomposition in the first 15 days. A chloroform treatment prevented decomposition, but Si release was unaffected. Disintegration continued throughout the experiments, with phytoliths being exposed and dissolved. Compared to the rate of release from straw into solution without soil, the release of Si into soil suspensions was increased during the first 20 days by adsorption on the soil, but was then reduced probably through the effect of Fe and Al on the phytolith surfaces. The extent of this blocking effect varied between soils and was not simply related to soil pH.

The fate and toxicity of the flavonoids naringenin and formononetin in soil

The flavonoid class of plant secondary metabolites play a multifunctional role in below-ground plant-microbe interactions with their best known function as signals in the nitrogen fixing legume-rhizobia symbiosis. Flavonoids enter rhizosphere soil as a result of root exudation and senescence but little is known about their subsequent fate or impacts on microbial activity. Therefore, the present study examined the sorptive behaviour, biodegradation and impact on dehydrogenase activity (as determined by iodonitrotetrazolium chloride reduction) of the flavonoids naringenin and formononetin in soil. Organic carbon normalised partition coefficients, log K-oc, of 3.12 (formononetin) and 3.19 (naringenin) were estimated from sorption isotherms and, after comparison with literature log K-oc values for compounds whose soil behaviour is better characterised, the test flavonoids were deemed to be moderately sorbed. Naringenin (spiked at 50 mu g g(-1)) was biodegraded without a detectable lag phase with concentrations reduced to 0.13 +/- 0.01 mu g g(-1) at the end of the 96 h time course. Biodegradation of formononetin proceeded after a lag phase of similar to 24 with concentrations reduced to 4.5 +/- 1% of the sterile control after 72 h. Most probable number (MPN) analysis revealed that prior to the addition of flavonoids, the soil contained 5.4 x 10(6) MPNg(-1) (naringenin) and 7.9 x 10(5) MPNg(-1) (formononetin) catabolic microbes. Formononetin concentration had no significant (p > 0.05) effect on soil dehydrogenase activity, whereas naringenin concentration had an overall but non-systematic impact (p = 0.045). These results are discussed with reference to likely total and bioavailable concentrations of flavonoids experienced by microbes in the rhizosphere. (c) 2007 Elsevier Ltd. All rights reserved.

The release of silicon from amorphous silica and rice straw in Sri Lankan soils

Silicon release from rice straw and amorphous silica when shaken in solution with five Sri Lankan soils was studied indirectly using sorption isotherms and changes in concentration and directly using straw in dialysis bags examined using electron microscopy. The aim was to further our understanding of the processes and factors affecting the release of straw-Si in soils and its availability to rice. The soils (alfisols and ultisols) shaken with 0.1 M NaCl (5 g per 125 mL for 250 days) produced concentrations of 1 - 4 mg L-1 of monosilicic acid-Si. Amorphous silica added to these suspensions (36.5 mg, containing 17 mg Si) raised the concentrations to 20 - 40 mg L-1, and added rice straw (0.5 g, containing 17 mg Si) gave 10 - 25 mg L-1. Sorption isotherms (7 days equilibrations) were used to calculate from the concentrations the amounts of Si released ( 24 - 38% and 8 - 21%, respectively). Both materials gave about 40 mg L-1 of monosilicic acid-Si plus 30 mg L-1 of disilicic acid-Si when shaken in solution alone (5 g per 125 mL). Straw in dialysis bags ( 0.5 g per 25 mL in 0.1 M NaCl) was shaken in soil suspension ( 5 g per 100 mL) for 60 days. Similar concentrations and releases were measured to those obtained above. About one fifth of the mass of straw was lost by decomposition in the first 15 days. A chloroform treatment prevented decomposition, but Si release was unaffected. Disintegration continued throughout the experiments, with phytoliths being exposed and dissolved. Compared to the rate of release from straw into solution without soil, the release of Si into soil suspensions was increased during the first 20 days by adsorption on the soil, but was then reduced probably through the effect of Fe and Al on the phytolith surfaces. The extent of this blocking effect varied between soils and was not simply related to soil pH.

Reliability of a method for evaluating porosity in denture base resins

Background: The method of porosity analysis by water absorption has been carried out by the storage of the specimens in pure water, but it does not exclude the potential plasticising effect of the water generating unreal values of porosity. Objective: The present study evaluated the reliability of this method of porosity analysis in polymethylmethacrylate denture base resins by the determination of the most satisfactory solution for storage (S), where the plasticising effect was excluded. Materials and methods: Two specimen shapes (rectangular and maxillary denture base) and two denture base resins, water bath-polymerised (Classico) and microwave-polymerised (Acron MC) were used. Saturated anhydrous calcium chloride solutions (25%, 50%, 75%) and distilled water were used for specimen storage. Sorption isotherms were used to determine S. Porosity factor (PF) and diffusion coefficient (D) were calculated within S and for the groups stored in distilled water. anova and Tukey tests were performed to identify significant differences in PF results and Kruskal-Wallis test and Dunn multiple comparison post hoc test, for D results (alpha = 0.05). Results: For Acron MC denture base shape, FP results were 0.24% (S 50%) and 1.37% (distilled water); for rectangular shape FP was 0.35% (S 75%) and 0.19% (distilled water). For Classico denture base shape, FP results were 0.54% (S 75%) and 1.21% (distilled water); for rectangular shape FP was 0.7% (S 50%) and 1.32% (distilled water). FP results were similar in S and distilled water only for Acron MC rectangular shape (p > 0.05). D results in distilled water were statistically higher than S for all groups. Conclusions: The results of the study suggest that an adequate solution for storing specimens must be used to measure porosity by water absorption, based on excluding the plasticising effect.

Chitosan, sisal cellulose, and biocomposite chitosan/sisal cellulose films prepared from thiourea/NaOH aqueous solution

Environmentally friendly biocomposites were successfully prepared by dissolving chitosan and cellulose in a NaOH/thiourea solvent with subsequent heating and film casting. Under the considered conditions, NaOH/thiourea led to chain depolymerization of both biopolymers without a dramatic loss of film forming capacities. Compatibility of both biopolymers in the biocomposite was firstly assessed through scanning electron microscopy, revealing an intermediate organization between cellulose fiber network and smoothness of pure chitosan. DSC analyses led to exothermic peaks close to 285 and 315 degrees C for the biocomposite, compared to the exothermic peaks of chitosan (275 degrees C) and cellulose (265 and 305 degrees C), suggesting interactions between chitosan and cellulose. Contact angle analyses pointed out the deformation that can occur at the surface due to the high affinity of the;e materials with water. T(2) NMR relaxometry behavior of biocomposites appeared to be dominated by chitosan. Other properties of films, as crystallinity, water sorption isotherms, among others, are also discussed. (C) 2010 Published by Elsevier Ltd.

Nanoparticles of octakis [3-(3-amino-1,2,4-triazole)propyl] octasilsesquioxane as ligands for Cu(II), Ni(II), Cd(II), Zn(II), and Fe(III) in aqueous solution

Nanoparticles of octakis[3-(3-amino-1,2,4-triazole)propyl]octasilsesquioxane (ATZ-SSQ) were tested as ligands, for transition-metal ions in aqueous solution with a special attention to sorption isotherms, ligand-metal interaction, and determination of metal ions in natural waters. The adsorption potential of the material ATZ-SSQ was compared with related [3(3-amino-1,2,4-triazole)propyl]silica gel (ATZ-SG). The adsorption was performed using a batchwise process and both organofunctionalized surfaces showed the ability to adsorb the metal ions from aqueous solution. The Langmuir model was used to simulate the sorption isotherms. The results suggest that the sorption of these metals on ATZ-SSQ and ATZ-SG occurs mainly by surface complexation. The equilibrium condition is reached at time lower than 3 min for ATZ-SSQ, while for ATZ-SG is only reached at time of 25 min. The maximum metal ion uptake values for ATZ-SSQ were higher than the corresponding values achieved with the ATZ-SG. In order to obtain more information on the ligand-metal interaction of the complexes on the surface of the ATZ-SSQ nanomaterial, ESR study with various degrees of copper loadings was carried out. The ATZ-SSQ was tested for the determination (in flow using a column technique) of the metal ions present in natural waters. (C) 2007 Elsevier B.V. All rights reserved.

Estudo do equilíbrio e cinética de adsorção de um corante aniônico em quitosana

The phenomenon of adsorption is of fundamental importance for the treatment of textile effluents and removal of dyes. Chitosan is characterized as an excellent adsorbent material, not only for its adsorption capacity but also the low cost production. Equilibrium and kinetic studies were developed in this study to describe the mechanism of adsorption of the anionic azo dye Orange G in chitosan, with the isotherms obtained from the variation of the concentration of dye in the continuous phase. The kinetics of the process was analyzed based on models involving the adsorption of molecules of the dye in nonpolar and polar sites. Adsorption experiments were carried out in water and in saline media with different NaCl concentrations, both for the determination of the equilibrium time as isotherms for making kinetic curves in which the amount of dye adsorbed measured indirectly varied with time. The experiments revealed the opening of the biopolymer structure with increasing concentration of Orange G, accompanied by high pH values and change on the type of interaction between the dye and the adsorbent surface, suggesting behavior advocated by the Langmuir equation in a certain range of concentration of the adsorbate and following the Henry's Law at higher concentrations, from the increased number of sites available for adsorption. The studies conducted showed that the saline medium reduces the chitosan s adsorption capacity according to a certain concentration, the occurrence of the cooperative adsorption process steps kinetic mechanism suggested as a new alternative for the interpretation of the phenomenon

Reliability of a method for evaluating porosity in denture base resins

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência da temperatura e da concentração do cloreto de sódio (NaCl) nas isotermas de sorção da carne de tambaqui (Colossoma macroparum)

As isotermas de sorção da carne de tambaqui desidratada osmoticamente foram determinadas a três temperaturas (5, 17 e 29ºC) e com duas concentrações de solução osmótica (10 e 30% de NaCl), pelo método gravimétrico. Quatro modelos de sorção foram testados para verificar o melhor ajuste; GAB, Oswin, BET e PELEG. Os dados experimentais se ajustaram satisfatoriamente aos modelos. O modelo escolhido para este trabalho foi o de PELEG. Para o ajuste nas curvas de sorção, foi feita a análise de regressão não-linear, usada o programa estatístico ORIGIN 4.0 para estimar as constantes dos modelos. A avaliação do melhor ajuste foi feita pela análise do coeficiente de determinação do ajuste (r²) e teste de Qui-quadrado (x²). Foram analisadas as influências da variação da temperatura e concentração de NaCl na atividade de água da carne do tambaqui. À medida que decresce a temperatura há um decréscimo na atividade de água. Um aumento na concentração do NaCl diminui a atividade de água. A propriedade termodinâmica estudada foi o calor isostérico de sorção. A medida que aumenta a concentração da solução osmótica aumenta o valor do calor isostérico de sorção.