Quality management of outsourcing welded structure: case China

For any international companies who wish to enter the Chinese market, quality is base on the fundamental. The companies are coming to realize the importance of quality gradually, thus companies have been put the quality problems on the agenda. The competitiveness of companies comes from quality. Quality is the key to success, and it can decide that the companies can be accepted or eliminated by the market. Due to the obvious benefits, the demand of the method of how to achieve high quality of product keeps growing. During achieving the high quality process, the main troubles come from the impact between Eastern and Western culture. Chinese culture which is different with Western one have lasted as long as five thousand years. Such a culture deeply rooted in the hearts of Chinese people, and effected generation after generation of Chinese people's working style and ways of thinking. This thesis determines how to find a good fit point between Eastern and Western culture. Doing right thing by the right way. The nature of improving quality is improving management level in fact. "How to manage, who should be managed", the thesis explains the basic and best option to achieve those. It describes three-dimension-style management to monitoring the working process. This kind of management style can inspect production process from horizontal and vertical direction. In this management way, it defines effective evaluation system to every subcontractor, and makes the companies to achieve the ultimate goal - satisfy quality. Because of the importance of human factor, the thesis determines the range of training of the inspector and welder due to the current situation of China. The results show that in order to reach reliable training effective evaluation, not only the quality of the human but also the ultimate goal of product quality.

Kys mig!

Soitinnus: lauluääni, piano.

Control methods for arc welding power supplies

Welding is one of the most important process of modern industry. Welding technology is used in the manufacture and repair a wide variety of products from different metals and alloys. In this thesis the different aspects of arc welding were discussed, such as stability and control of welding arc, power supplies for arc welding (especially the welding inverters because it is the most modern welding power source). All parameters of power source have influence on the arc parameters and its by-turn influence on quality. The ways of control for arc welding inverter power sources have been considered. Calculations and modeling in Matlab/Simulink were done for PI control method. All parameters of power source have influence on the arc parameters and its by-turn influence on quality.

Investigation of Oxygen Cutting Process in Solid-State Welding

The oxygen cutting is a thermal cutting process, in which metal is heated locally up to its ignition temperature and burnt off by oxygen blast. Oxygen cutting can be used to remove upset metal of a hollow bar occurred due to solid-state welding process. The main goal of this research was to establish a connection between oxygen blasts and mass of metal removed and relate findings to production to suggest improvements to the current process. This master´s thesis describes the designing and building of a test rig for oxygen blowing measurements. It also contains all executed tests and test results, which were carried out. There are different cutting parameters which were studied as well as their effect on cutting process. The oxygen cutting process, used in solid-state welding process, can be improved by the test results.

"Jag har hittat mig själv och barnen" : barnträdgårdslärares professionella självutveckling genom ett pedagogisk-psykologiskt interventionsprogram

Människans människoblivande eller självutveckling sker genom hennes relationer till andra människor. För barn är därför relationerna till de vuxna inom dagvård och skola av central betydelse för utvecklingen av deras självkänsla. Pedagoger som handhar de yngsta barnens fostran behöver ha en utvecklad pedagogisk relationskompetens som innefattar förmåga att handskas med egna och andras känslor. I avhandlingen beskrivs hur ett pedagogisk-psykologiskt interventionsprogram växer fram och genomförs med åtta yrkesverksamma barnträdgårdslärare i syfte att utveckla deras yrkespersonliga kompetens. Därefter redogörs för den empiriska studien, vars syfte är att analysera och beskriva de kvalitativa förändringarna i barnträdgårdslärarnas själv-i-relation och de utmärkande dragen för förändringsprocessen. Studien baserar sig på fenomenologisk-existentialistiska tankegångar och självpsykologisk teori. Resultatet visar på möjliga förändringar i fråga om fördjupad teoretisk förståelse, ökad beredskap att ta barns perspektiv, förändrad handlingsberedskap, ökad självkänsla, stärkt professionellt självförtroende, förändrat didaktiskt förhållningssätt och förändrade förhållningssätt i relationer. Känslornas och reflektionens centrala betydelse i den förändringsprocess som leder fram till ett förändrat själv-i-relation diskuteras också. Studien har betydelse framför allt för lärarutbildning och lärarfortbildning.

Advanced orbital pipe welding

Since the introduction of automatic orbital welding in pipeline application in 1961, significant improvements have been obtained in orbital pipe welding systems. Requirement of more productive welding systems for pipeline application forces manufacturers to innovate new advanced systems and welding processes for orbital welding method. Various methods have been used to make welding process adaptive, such as visual sensing, passive visual sensing, real-time intelligent control, scan welding technique, multi laser vision sensor, thermal scanning, adaptive image processing, neural network model, machine vision, and optical sensing. Numerous studies are reviewed and discussed in this Master’s thesis and based on a wide range of experiments which already have been accomplished by different researches the vision sensor are reported to be the best choice for adaptive orbital pipe welding system. Also, in this study the most welding processes as well as the most pipe variations welded by orbital welding systems mainly for oil and gas pipeline applications are explained. The welding results show that Gas Metal Arc Welding (GMAW) and its variants like Surface Tension Transfer (STT) and modified short circuit are the most preferred processes in the welding of root pass and can be replaced to the Gas Tungsten Arc Welding (GTAW) in many applications. Furthermore, dual-tandem gas metal arc welding technique is currently considered the most efficient method in the welding of fill pass. Orbital GTAW process mostly is applied for applications ranging from single run welding of thin walled stainless tubes to multi run welding of thick walled pipes. Flux cored arc welding process is faster process with higher deposition rate and recently this process is getting more popular in pipe welding applications. Also, combination of gas metal arc welding and Nd:YAG laser has shown acceptable results in girth welding of land pipelines for oil and gas industry. This Master’s thesis can be implemented as a guideline in welding of pipes and tubes to achieve higher quality and efficiency. Also, this research can be used as a base material for future investigations to supplement present finding.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

The Productivity, Economy and Quality of Welding in the Different Geographical Areas of China - Today and in the Future

This master’s thesis gives out the real situation of the China welding industry and factories nowadays in different geographical areas, in order to inform the Finnish companies who have the willing to find a Chinese welding subcontractor a proper and correct selection concept by analyzing and supplying the information of different scale and form welding factories in different Chinese areas. The first section of this thesis gives out the general situation about the co-operation between China and Finland in the welding industry, also includes the general introduction of the Chinese welding industry. The second section gives out the geographical compartmentalization result of Chinese welding industry, which is where and how many areas will be studied in this thesis. The main body of this thesis is the real information of welding productivity, welding cost, and welding quality in China. All the information was collected from real factories in China by the author. The last section of this thesis is the improvements to the Chinese welding factories that have the willing to become a subcontractor, and the suggestions to the Finnish companies who may find a Chinese welding factory as their subcontractor in future.

Railonvalmistusmenetelmät alumiinin hitsauksessa

Tämä kandidaatintyö liittyy Lappeenrannan teknillisessä yliopistossa 2008-2011 käynnissä olevaan Tekesin tutkimushankkeeseen ”Alumiiniveneen hitsauksen automatisointi”. Tällä hetkellä Suomessa pienemmät veneenrungot hitsataan käsin, sillä robottihitsauksessa tulee ongelmaksi hitsin luokse pääseminen, etenkin kokoonpanohitsauksessa. Automaatiohitsauksessa myös tarvitaan huomattavasti tarkemmat railotoleranssit kuin käsinhitsauksessa, koska hitsausrobotti on sokea hitsausliitosten poikkeamille. Hitsauksen automatisoinnilla pyritään nostamaan nykyistä tuotantokapasiteettia ja yleisesti parantamaan alumiinirakenteiden hitsien laatua. Työn tarkoituksena on tutkia erilaisia railonvalmistusmenetelmiä alumiinin hitsausta varten, sekä casena pohtia railonvalmistusmenetelmien soveltuvuutta robotisoituun MIG-hitsaukseen alumiinisessa veneenrungossa. Työssä pohditaan hitsauksen, sekä robotisoidun hitsauksen railonvalmistukseen soveltuvia leikkausmenetelmiä, railonvalmistusta yleisesti, toleransseja, alumiinin työstöominaisuuksia, sekä leikkausmenetelmien taloudellisuutta. Työssä käsitellään railovaatimuksia mm. MIG-, TIG-, plasma-, sekä laserhitsaukselle.

Vill du komma med mig

Soitinnus: lauluääni, piano.

Determinação de metodologias para teste de germinação e vigor de sementes de quixabeira (Bumelia obtusifolia Roem et Schult. var. excelsa (DC) Mig.)

Objetivou-se desenvolver metodologias para avaliação da qualidade de sementes de quixabeira que se encontra ameaçada de extinção, pelo fato de as cascas da árvore serem usadas na medicina popular. Foram realizados testes de secagem em laboratório e casa-de-vegetação por 0, 24, 48, 72, 96, 120, 144, 168 e 196 h de superação de dormência (escarificação com lixa; imersão em ácido sulfúrico por um, três, cinco e sete min; escarificação com lixa, seguida de embebição em água destilada por 12, 24, 36 e 48 h; embebição em água destilada por 12, 24, 36 e 48 h e testemunha) e com substratos (sobre e entre-areia, vermiculita, papel, bioplant®, plantmax e rolo de papel germitest) em diferentes temperaturas (20-30, 30 e 35 °C). A secagem em casa de vegetação prejudicou a qualidade das sementes. A escarificação com lixa é o tratamento mais eficiente para superação da dormência. As temperaturas de 30 °C com o substrato entre papel e 35 ºC com o substrato entre vermiculita são adequadas para testes de germinação com sementes de quixabeira.

Kaarihitsauksen suojakaasun tunnistus ja virtauksen mittaus ultraäänellä

Kaasukaarihitsauksessa suojakaasuna käytetään yleensä argonin ja hiilidioksidin tai argonin ja heliumin seoksia. Suojakaasu vaikuttaa useisiin hitsausominaisuuksiin, jotka puolestaan vaikuttavat hitsauksen laatuun ja tuottavuuteen. Automaattisella suojakaasun tunnistuksella ja virtausmäärän mittauksella voitaisiin tehdä hitsauksesta paitsi käyttäjän kannalta yksinkertaisempaa, myös laadukkaampaa. Työn tavoite on löytää mahdollisimman edullinen ja kuitenkin mahdollisimman tarkasti kaasuseoksia tunnistava menetelmä, jota voitaisiin hyödyntää MIG/MAG-hitsauskoneeseen sisäänrakennettuna. Selvä etu on, jos menetelmällä voidaan mitata myös kaasun virtausmäärä. Äänennopeus kaasumaisessa väliaineessa on aineen atomi- ja molekyylirakenteesta ja lämpötilasta riippuva ominaisuus, joka voidaan mitata melko edullisesti. Äänennopeuden määritys perustuu ääniaallon kulkuajan mittaamiseen tunnetun pituisella matkalla. Kaasun virtausnopeus on laskettavissa myötä- ja vastavirtaan mitattujen kulkuaikojen erotuksen avulla. Rakennettu mittauslaitteisto koostuu kahdesta ultraäänimuuntimesta, joiden halkaisija on 10 mm ja jotka toimivat sekä lähettimenä että vastaanottimena. Muuntimet ovat 140 mm:n etäisyydellä toisistaan virtauskanavassa, jossa suojakaasu virtaa yhdensuuntaisesti äänen kanssa. Virtauskanava on putki, jossa on käytetty elastisia materiaaleja, jotta ääniaaltojen eteneminen kanavan runkoa pitkin minimoituisi. Kehitetty algoritmi etsii kahden lähetetyn 40 kHz:n taajuisen kanttiaaltopulssin aiheuttaman vasteen perusteella ääniaallon saapumisajanhetken. Useiden mittausten, tulosten lajittelun ja suodatuksen jälkeen tuntemattomalle kaasulle lasketaan lämpötilakompensoitu vertailuluku. Tuntematon kaasu tunnistetaan vertailemalla lukua tunnettujen kaasuseosten mitattuihin vertailulukuihin. Laitteisto tunnistaa seokset, joissa heliumin osuus argonissa on enintään 50 %. Hiilidioksidia sisältävät argonin seokset puolestaan tunnistetaan puhtaaseen hiilidioksidiin asti jopa kahden prosenttiyksikön tarkkuudella. Kaasun tilavuusvirtausmittauksen tarkkuus on noin 1,0 l/min.

Laatu ja tuottavuus hitsaavassa verkostossa

Diplomityössä tarkastellaan laadun ja tuottavuuden parantamisen keinoja hitsaavassa verkostossa MIG/MAG-hitsauksen osalta. Työn taustalla vaikuttaa Total Welding Management -menetelmä, mikä on hitsaustoimintojen kokonaisvaltaiseen johtamiseen ja hallintaan kehitetty toimintamalli. Työn teoriaosassa käsitellään laatuajattelua ja yritysyhteistyötä hitsaavan teollisuuden yrityskentässä sekä hitsauskustannuksiin vaikuttavia tekijöitä. Tutkimusosuus sisältää yritysverkoston nykytilan tarkastelun sekä kehitystoimenpiteitä kohti verkoston yhteistä toimintamallia saavuttaa tehokas ja kannattava yhteistyö. Hitsaustyön kustannukset määritetään suurelta osin suunnittelussa. Laatuun voidaan vaikuttaa merkittävästi hitsaustyötä edeltävissä toiminnoissa sekä hitsaajan työn tukemisella. Kokonaisvaltaisen hyödyn saavuttaminen hitsaustyön tuottavuuden parantamisessa vaatii kaikkien toimintojen tarkastelua sen sijaan, että tehostetaan vain hitsaamon toimintaa. Itse hitsaus voi olla vain pieni osa hitsaustoimintojen kokonaishallintaa. Toimintamallin luominen laadunvarmistukseen, suunnittelun ja valmistuksen yhteistyöhön sekä hitsaustoimintojen hallintaan mahdollistaa hitsaavan verkoston toiminnan tehostamisen sekä laadun paranemisen. Tämä saavutetaan viemällä toimintamalli osaksi jokapäiväistä työtä, lähelle valmistusta, ja ohjeistamalla, että jokainen tietää kuinka toimia. Esimerkiksi työssä tarkastellun yhden tuotteen osalta ohjeistus turhan työn vähentämiseksi tuotti 19 % tuotannon kasvun työvuoron aikana. Tilaus-toimitusketjun tuottavuuteen ja kannattavuuteen voidaan vaikuttaa merkittävästi käymällä läpi konkreettisesti valmistettavat tuotteet ja niihin liittyvät toiminnot. Diplomityössä tehtyjen tarkastelujen ja havaintojen avulla käytännön työ tulee jatkumaan yritysverkostossa tapahtuvassa kehitystyössä.

Welding development of crane main girder

Konecranes Corporation manufactures huge steel structures in 16 factories worldwide, in which the environment and quality varies. The company has a desire to achieve the same weld quality in each factory, regardless of the manufacturing place. The main subject of this master’s thesis was to develop the present box girder crane welding process, submerged arc welding and especially the fillet welding. Throughput time and manufacturing costs can be decreased by welding the full penetration fillet weld without a bevel, changing present groove types for more appropriate ones and by achieving the desired weld quality on the first time. Welding experiments of longitudinal fillet welding were made according to the present challenges, which the manufacturing process is facing. In longitudinal fillet welding tests the main focus was to achieve full penetration fillet weld for 6, 8 and 10 millimeters thick web plates with single and twin wire submerged arc welding. Full penetration was achieved with all the material thicknesses, both with single and twin wire submerged arc welding processes. The main problem concerning the weld was undercutting and shape of the weld bead. The question about insufficiency of presently used power sources with twin wire was risen up during testing, due to the thicknesses that require high welding current. Bigger power source is required when box girders are welded nonstop, if twin wire is used. For single wire process the penetration was achieved with significantly less amperage than with twin wire.