Generation of 1.5-12 ns width-tunable 532 nm pulses by adopting laser-induced plasma shutter technique

The pulse-shaping technique has found widespread applications in nonlinear optics and material processing. Experimental research on laser-induced plasma shutter to control the 532 nm pulse width is conducted. The impacts of the total pulse output energy on pulse compression are investigated, and a useful conclusion can be drawn that there exists an optimal value of pulse energy at which the shortest output pulse of 3.23 ns can be obtained without a device for delay-time. Once the device for delay-time is employed to change the optical differences between two laser paths, the pulse width can be further shortened to 1.51 ns. In short, the 1.5-12 ns width-tunable 532 nm laser pulses have been obtained by adopting the laser-induced plasma shutter technique. (C) 2007 Elsevier GmbH. All rights reserved.

Avaliação de condicionadores em solo para uso em telhados verdes com vistas à retenção hídrica.

As inundações são fenômenos naturais que ocorrem devido às chuvas de grande magnitude, agravadas nas áreas urbanas pela impermeabilização do solo e ineficiência dos sistemas de drenagem. Os telhados verdes surgem como uma medida compensatória estrutural que pode reter parte da água precipitada, adiando o pico de escoamento. O objetivo deste trabalho foi de desenvolver uma combinação de solo e condicionadores para telhado verde, promovam um aumento relevante na capacidade de retenção hídrica e um maior adiamento do pico de escoamento das águas pluviais. Este estudo foi dividido em duas etapas. Na Etapa 1, foram analisadas, em colunas de percolação, três condicionadores nas seguintes concentrações: Gel retentor Stockosorb (2; 4; 6 g/dm3), Fertilizante de liberação lenta Osmocote (4,7; 7,1; 9,0 g/dm3) e Zeólita (30; 50; 70 g/dm3), em três eventos (regas) consecutivos de chuva simulada na intensidade de 57 mm/h. A avaliação das concentrações mais adequadas dentre as testadas para cada condicionante foi baseada nas análises referentes à retenção hídrica (altura do meio após a rega; tempo de adiamento do escoamento; mm retidos; intensidade da água percolada em mm/min) e à qualidade da água percolada (pH, oxigênio dissolvido, turbidez e sólidos). Na Etapa 2, foi avaliada, em vasos, a influência da presença de três espécies de plantas (Arachis pintoi; Raphanus sativus; Lavandula angustifolia) em dois tipos de meio: solo sem condicionadores; solo com condicionadores nas melhores concentrações indicadas na Etapa 1, sendo simulada apenas um evento de chuva de 57 mm/h. Foram analisados parâmetros biológicos (germinação; plantas sobreviventes; comprimento do caule e da raiz; pesos da biomassa do caule e da raiz); retenção hídrica (altura do meio após a rega; tempo de adiamento do escoamento; mm retidos; intensidade da água percolada em mm/min); qualidade da água percolada (pH; oxigênio dissolvido; turbidez; sólidos; nitrato; amônia; fósforo total). Os resultados da Etapa 1 indicaram que o gel promoveu de forma significativa um aumento na retenção hídrica, e adiou o início da percolação de água, além de promover ligeira elevação do pH na água percolada. A adição de zeólita resultou em um aumento significativo da retenção hídrica, porém tal aumento não é vantajoso visto que este representa um custo adicional que poderia ser reduzido com o aumento da proporção do gel na coluna. A adição de fertilizantes não promoveu mudanças na qualidade da água percolada. Na Etapa 2, somente o efeito da presença de A. pintoi (maior produção de biomassa de raiz e caule) e R. sativus foram avaliadas. A presença dos condicionantes no solo proporcionou um desempenho significativamente superior em relação a retenção hídrica (altura do substrato e adiamento do pico de chuva) e qualidade da água percolada (pH e turbidez) quando comparados aos testes realizados na presença somente de solo. O fertilizante influenciou nas altas concentrações dos nutrientes (nitrogênio e fósforo) na água percolado nos resultados. A presença do gel no substrato, resultou numa capacidade superior de retenção de hídrica, e consequentemente no adiamento do pico de intensidade de chuva. Sendo assim, recomenda-se a aplicação do gel em telhados verdes para futuros estudos em ambientes externos.

Three-dimensional direct numerical simulations of autoignition in turbulent non-premixed flows with simple and complex chemistry

3D Direct Numerical Simulations (DNS) of autoignition in turbulent non-premixed flows between fuel and hotter air have been carried out using both 1-step and complex chemistry consisting of a 22 species n-heptane mechanism to investigate spontaneous ignition timing and location. The simple chemistry results showed that the previous findings from 2D DNS that ignition occurred at the most reactive mixture fraction (ξMR) and at small values of the conditional scalar dissipation rate (N|ξMR) are valid also for 3D turbulent mixing fields. Performing the same simulation many times with different realizations of the initial velocity field resulted in a very narrow statistical distribution of ignition delay time, consistent with a previous conjecture that the first appearance of ignition is correlated with the low-N content of the conditional probability density function of N. The simulations with complex chemistry for conditions outside the Negative Temperature Coefficient (NTC) regime show behaviour similar to the single-step chemistry simulations. However, in the NTC regime, the most reactive mixture fraction is very rich and ignition seems to occur at high values of scalar dissipation. Copyright © 2006 by ASME.

Modeling evaporation effects in conditional moment closure for spray autoignition

Simulations of an n-heptane spray autoigniting under conditions relevant to a diesel engine are performed using two-dimensional, first-order conditional moment closure (CMC) with full treatment of spray terms in the mixture fraction variance and CMC equations. The conditional evaporation term in the CMC equations is closed assuming interphase exchange to occur at the droplet saturation mixture fraction values only. Modeling of the unclosed terms in themixture fraction variance equation is done accordingly. Comparison with experimental data for a range of ambient oxygen concentrations shows that the ignition delay is overpredicted. The trend of increasing ignition delay with decreasing oxygen concentration, however, is correctly captured. Good agreement is found between the computed and measured flame lift-off height for all conditions investigated. Analysis of source terms in the CMC temperature equation reveals that a convective-reactive balance sets in at the flame base, with spatial diffusion terms being important, but not as important as in lifted jet flames in cold air. Inclusion of droplet terms in the governing equations is found to affect the mixture fraction variance field in the region where evaporation is the strongest, and to slightly increase the ignition delay time due to the cooling associated with the evaporation. Both flame propagation and stabilization mechanisms, however, remain unaffected. © 2011 Taylor & Francis.

Complex chemistry DNS of n-heptane spray autoignition at high pressure and intermediate temperature conditions

Direct Numerical Simulations (DNS) of turbulent n-heptane sprays autoigniting at high pressure (P=24bar) and intermediate air temperature (Tair=1000K) have been performed to investigate the physical mechanisms present under conditions where low-temperature chemistry is expected to be important. The initial turbulence in the carrier gas, the global equivalence ratio in the spray region, and the initial droplet size distribution of the spray were varied. Results show that spray ignition exhibits a spotty nature, with several kernels developing independently in those regions where the mixture fraction is close to its most reactive value ξMR (as determined from homogeneous reactor calculations) and the scalar dissipation rate is low. Turbulence reduces the ignition delay time as it promotes mixing between air and the fuel vapor, eventually resulting in lower values of scalar dissipation. High values of the global equivalence ratio are responsible for a larger number of ignition kernels, due to the higher probability of finding regions where ξ=ξMR. Spray polydispersity results in the occurrence of ignition over a wider range of mixture fraction values. This is a consequence of the inhomogeneities in the mixing field that characterize these sprays, where poorly mixed rich spots are seen to alternate with leaner ones which are well-mixed. The DNS simulations presented in this work have also been used to assess the applicability of the Conditional Moment Closure (CMC) method to the simulation of spray combustion. CMC is found to be a valid method for capturing spray autoignition, although care should be taken in the modelling of the unclosed terms appearing in the CMC equations. © 2013 The Combustion Institute.

Autoignition of alcohols and ethers in a rapid compression machine

The autoignition characteristics of methanol, ethanol and MTBE (methyl tert-butyl ether) have been investigated in a rapid compression machine at pressures in the range 20-40 atm and temperatures within 750-1000 K. All three oxygenated fuels tested show higher autoignition temperatures than paraffins, a trend consistent with the high octane number of these fuels. The autoignition delay time for methanol was slightly lower than predicted values using reported reaction mechanisms. However, the experimental and measured values for the activation energy are in very good agreement around 44 kcal/mol. The measured activation energy for ethanol autoignition is in good agreement with previous shock tube results (31 kcal/mol), although ignition times predicted by the shock tube correlation are a factor of three lower than the measured values. The measured activation energy for MTBE, 41.4 kcal/mol, was significantly higher than the value previously observed in shock tubes (28.1 kcal/mol). The onset of preignition, characterized by a slow energy release prior to early ignition was observed in some instances. Possible reasons for these ocurrences are discussed. © Copyright 1993 Society of Automotive engineers, Inc.

A method for individual identification of echolocation signals in free-ranging finless porpoises carrying data loggers

Echolocation click events of a free-ranging juvenile and an adult finless porpoise (Neophocaena phocaenoides) were recorded with an acoustic data logger. Additionally, dive depth and swim speed of the juvenile were recorded with a behavior data logger. Echoes of echolocation signals from the water surface were clearly detected in shallow dives approximately less than 2 m. The delay time between a surface echo and a direct signal corresponded with the two-way transmission time for the animal's depth, indicating that the signals originated from the animal wearing the data loggers. The finless porpoises produced echolocation signals frequently and were thought to be able to detect their depth by listening to echoes from the water surface. (C) 2000 Acoustical Society of America. [S0001-4966(00)01609-X].

Signal bandwidth of general N x N multimode interference couplers

Analytical expression of signal bandwidth of general straight and tapered N x N multimode interference (MMI) couplers is presented. The signal bandwidth is characterized as a function of mode relative energy, mode propagation delay time, and mode pulse broadening in the multimode section of MMI coupler. The model is used to evaluate the signal bandwidth of specific couplers. Results indicate that the signal bandwidth decreases seriously with the increase of channel number and channel guide space. Compared with the straight MMI coupler, the tapered MMI coupler has an improved signal bandwidth.

Degenerate four-wave-mixing signals from dc- and ac-driven semiconductor superlattice

Within the one-dimensional tight-binding model;rnd chi-3 approximation, we have calculated four-wave-mixing (FWM) signals for a semiconductor superlattice in the presence of both static and high-frequency electric fields. When the exciton effect is negligible, the time-periodic field dynamically delocalizes the otherwise localized Wannier-Stark states, and accordingly quasienergy band structures are formed, and manifest in the FWM spectra as a series of equally separated continua. The width of each continuum is proportional to the joint width of the valence and conduction minibands and is independent of the Wannier-Stark index. The realistic homogeneous broadening blurs the continua into broad peaks, whose line shapes, far from the Lorentzian, vary with the delay time in the FWM spectra. The swinging range of the peaks is just the quasienergy bandwidth. The dynamical delocalization (DDL) also induces significant FWM signals well beyond the excitation energy window. When the Coulomb interaction is taken into account, the unequal spacing between the excitonic Wannier-Stark levels weakens the DDL effect, and the FWM spectrum is transformed into groups of discrete lines. Strikingly, the groups are evenly spaced by the ac field frequency, reflecting the characteristic of the quasienergy states. The homogeneous broadening again smears out the line structures, leading to the excitonic FWM spectra quite similar to those without the exciton effect. However, all these features predicted by the dynamical theory do not appear in a recent experiment [Phys. Rev. Lett. 79, 301 (1997)], in which, by using the static approximation the observed Wannier-Stark ladder with delay-time-dependent spacing in the FWM spectra is attributed to a temporally periodic dipole field, produced by the Bloch oscillation of electrons in real space. The contradiction between the dynamical theory and the experiments is discussed. In addition, our calculation indicates that the dynamical localization coherently enhances the time-integrated FWM signals. The feasibility of using such a technique to study the dynamical localization phenomena is shown. [S0163-1829(99)10607-6].

Scan test in 18x8 bits Booth Coding-Wallace Tree multiplier

Scan test can be inserted around hard IP cores that have not been designed with DFT approaches. An 18x18 bits Booth Coding-Wallace Tree multiplier has been designed with full custom approach with 0.61 m CMOS technology. When we reuse the multiplier in another chip, scan chain has been inserted around it to increase the fault coverage. After scan insertion, the multiplier needs 4.7% more areas and 24.4% more delay time, while the fault coverage reaches to 95%.

Effects of Fracture Seepage on the Stability of Landslide during Reservoir Water Level Fluctuation

The hydraulic conductivity function of fractures is a key scientific question to describe and reveal the process and the role of water seepage reasonably. In this paper, the generation technology of random fracture network and the latest numerical computation method for equivalent permeability tensor of fracture network are applied to analyze the landslide located at Wangjiayuanzi in Wanzhou District of Chongqing by simulating the changes of the seepage field caused by the running of the Three Gorges Reservoir. The influences of the fracture seepage on the seepage field and stability of the landslide were discussed with emphasis. The results show that the fractures existing in the soil increase the permeability coefficient of the landslide body and reduce the delay time of the underground water level in the landslide which fluctuates relative to the water level of reservoir，that causes the safe coefficient of the slope changes more gently than that of the same slope without fractures. It means, if only water level fluctuating condition is concerned, the fractures existing in the soil plays a positive role to the stability of slopes.

Microelements in Potato and Lily Samples Studied by Laser-Induced Breakdown spectroscopy Technology

A LIBS setup was built in the Institute of Modern Physics. In our experiments, LIBS spectra produced by infrared radiation of Nd : YAG nanosecond laser with 100 and 150 mJ pulse energy, respectively, were measured by fiber optic spectrometer in the ranges of 230-430 run and 430-1080 nm with a delay time of 1.7 and gate width of 2 ms for potato and lily samples prepared by vacuum freeze-dried technique. The lines from different metal elements such as K, Ca, Na, Mg, Fe, Al, Mn and Ti, and nonmetal elements such as C, N, O and H, and some molecular spectra from C-2, CaO, and CN were identified according to their wavelengths. The relative content of the six microelements, Ca, Na, K, Fe, Al, and Mg in the samples were analyzed according to their representative line intensities. By comparison we found that there are higher relative content of Ca and Na in lily samples and higher relative content of Mg in potato samples. The experimental results showed that LIBS technique is a fast and effective means for measuring and comparing the contents of microelements in plant samples.

面向网络生存时间的传感器网络融合延迟分配算法

融合延迟分配策略是影响数据融合效率的重要因素之一,而数据融合的目的是减少数据冗余,降低网络能量消耗,延长网络生存时间.提出了一种面向网络生存时间的延迟分配算法,该算法直接以网络生存时间为优化目标,根据对网络生存时间的贡献分配传输延迟;通过理论推导证明了该算法的有效性;引入动态规划方程,给出了该算法的具体实现;最后通过仿真实验给出了各参数对网络生存时间的影响关系.

一类时滞不确定非线性系统的鲁棒控制器设计

针对一类具有单输入滞后不确定非线性系统 ,采用精确反馈线性化方法和 Lyapunov方法设计出一种使系统终极有界 ( UUB)的无记忆光滑状态反馈鲁棒控制器 .仿真算例表明了本文所采用方法的有效性 .