Estudo e caracterização de matérias-primas para o desenvolvimento de blocos sílico-calcários

The types of products manufactured calcium silicate blocks are very diversified in its characteristics. They include accessory bricks, blocks, products in dense material, with or without reinforcements of hardware, great units in cellular material, and thermal insulating products. The elements calcium silicate are of great use in the prefabricated construction, being formed for dense masses and hardened by autoclaving. This work has for objective develop formulations that make possible the obtaining of calcium silicate blocks with characteristics that correspond the specifications technical, in the State of the Rio Grande of the North, in finality of obtaining technical viability for use in the civil construction. The work studied the availability raw materials from convenient for the production of calcium silicate blocks, and the effect of variations of the productive process on the developed products. The studied raw materials were: the quartz sand from the city of São Gonçalo do Amarante/RN, and two lime, a hydrated lime and a pure lime from the city of Governador Dix-Sept Rosado/RN. The raw materials collected were submitted a testes to particle size distribution, fluorescence of X rays, diffraction of X rays. Then were produced 8 formulations and made body-of-test by uniaxial pressing at 36 MPa, and cured for 7 hours at about 18 kgf/cm2 pressing and temperature of approximately 180 °C. The cure technological properties evaluated were: lineal shrinkage, apparent density, apparent porosity, water absorption, modulus of rupture flexural (3 points), resistance compression, phase analysis (XRD) and micromorphological analysis (SEM). From the results presented the technological properties, was possible say that utilization of hydrated lime becomes more viable its utilization in mass limestone silica, for manufacture of calcium silicate blocks

Metodologia de análise e diagnóstico de fratura em um componente automotivo sujeito a cargas cíclicas alternadas

The competitiveness of the trade generated by the higher availability of products with lower quality and cost promoted a new reality of industrial production with small clearances. Track deviations at the production are not discarded, uncertainties can statistically occur. The world consumer and the Brazilian one are supported by the consumer protection code, in lawsuits against the products poor quality. An automobile is composed of various systems and thousands of constituent parts, increasing the likelihood of failure. The dynamic and security systems are critical in relation to the consequences of possible failures. The investigation of the failure gives us the possibility of learning and contributing to various improvements. Our main purpose in this work is to develop a systematic, specific methodology by investigating the root cause of the flaw occurred on an axle end of the front suspension of an automobile, and to perform comparative data analyses between the fractured part and the project information. Our research was based on a flaw generated in an automotive suspension system involved in a mechanical judicial cause, resulting in property and personal damages. In the investigations concerning the analysis of mechanical flaws, knowledge on materials engineering plays a crucial role in the process, since it enables applying techniques for characterizing materials, relating the technical attributes required from a respective part with its structure of manufacturing material, thus providing a greater scientific contribution to the work. The specific methodology developed follows its own flowchart. In the early phase, the data in the records and information on the involved ones were collected. The following laboratory analyses were performed: macrography of the fracture, micrography with SEM (Scanning Electron Microscope) of the initial and final fracture, phase analysis with optical microscopy, Brinell hardness and Vickers microhardness analyses, quantitative and qualitative chemical analysis, by using X-ray fluorescence and optical spectroscopy for carbon analysis, qualitative study on the state of tension was done. Field data were also collected. In the analyses data of the values resulting from the fractured stock parts and the design values were compared. After the investigation, one concluded that: the developed methodology systematized the investigation and enabled crossing data, thus minimizing diagnostic error probability, the morphology of the fracture indicates failure by the fatigue mechanism in a geometrically propitious location, a tension hub, the part was subjected to low tensions by the sectional area of the final fracture, the manufacturing material of the fractured part has low ductility, the component fractured in an earlier moment than the one recommended by the manufacturer, the percentages of C, Si, Mn and Cr of the fractured part present values which differ from the design ones, the hardness value of the superior limit of the fractured part is higher than that of the design, and there is no manufacturing uniformity between stock and fractured part. The work will contribute to optimizing the guidance of the actions in a mechanical engineering judicial expertise

Y-TZP ceramic processing from coprecipitated powders: A comparative study with three commercial dental ceramics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Crystal Structure Determination of Mebendazole Form A Using High-Resolution Synchrotron X-Ray Powder Diffraction Data

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Synthesis and characterization of CuO flower-nanostructure processing by a domestic hydrothermal microwave

The synthesis and characterization of CuO flower-nanostructure processed in domestic hydrothermal microwave oven was presented. Phase analysis was carried out using X-ray diffraction (XRD) and micro-Raman scattering (MRS) and the results confirmed the CuO flower-nanostructure as a single-phase. The field-emission scanning electron microscopy (FEG-SEM) was used to estimate the average spheres diameter while transmission electron microscope (TEM) to observe the thorn of the flower-nanostructures. The mechanism of CuO flower-nanostructures formation is proposed and explained. (c) 2007 Elsevier B.V. All rights reserved.

Biodigestão anaeróbia de dejetos de suínos sob efeito de três temperaturas e dois níveis de agitação do substrato: considerações sobre a partida

Neste trabalho, avaliou-se a biodigestão anaeróbia de dejetos de suínos. Para isso, foi utilizado esquema laboratorial, constituído de 24 digestores com volume total de 14 L, sendo cada um abastecido com dejetos de suínos em fase de terminação, diluídos em água, perfazendo 10 L de volume útil de substrato com concentração inicial de sólidos totais de 6%. Três grupos formados por oito desses biodigestores foram expostos a três temperaturas (25; 35 e 40 ºC) e a dois níveis de agitação (com e sem) do substrato. A análise da fase de partida foi feita com base na produção média acumulada de biogás, num período de 71 dias. Os resultados demonstraram que a agitação não interferiu e que o melhor desempenho, inclusive o menor tempo gasto para atingir determinado nível de produção de biogás, foi verificado na temperatura de 35 ºC.

Identificação de regiões pluviometricamente homogêneas no Estado do Rio de Janeiro, utilizando-se valores mensais

O objetivo deste trabalho é dar uma contribuição ao estudo das condições climáticas do Estado do Rio de Janeiro, visando a uma melhor Classificação Climática por meio da identificação de regiões homogêneas em precipitação. Para isto foram utilizadas médias mensais da precipitação de 48 estações meteorológicas, em um período de 30 anos (1971-2000). A análise hierárquica de agrupamento, a orografia e a proximidade do mar, mostraram que o Estado do Rio de Janeiro pode ser dividido, quanto à precipitação, em seis regiões pluviometricamente homogêneas o que possibilitou classificar as estações meteorológicas pelo método de classificação não hierárquica k-means. A região norte do Estado, com precipitações anuais em torno de 870 mm é a mais seca, e a região da encosta sul da Serra do Mar, com 2020 mm, é a mais chuvosa. Mas, em ambas as regiões, os valores da precipitação da estação chuvosa representam em torno de 70% dos totais anuais.

Influence of the substitution of Y2O3 for CeO2 on the mechanical and microstructural properties of silicon nitride

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of PbO excess on the formation of lead magnesium niobate perovskite by the columbite method

The effect of lead excess on the pyrochlore-type formation in Pb(Mg1/3Nb2/3)O-3 (PMN) powders has been investigated. The polymeric precursor method was used in the synthesis of the columbite in association to the partial oxalate method to synthesize the PMN powder samples. Structure refinement of the columbite precursor and PMN powders was carried out using the Rietveld method. The quantitative phase analysis showed that the amount of perovskite phase is not affected by PbO excess, but a great excess drives the pyrochlore-type formation so that 3 wt.% of PbO causes the predominance of Mg-containing pyrochlore phase. Using the refined data obtained from the Rietveld refinement, the compositional fluctuation in the perovskite phase was calculated from Nb/Mg ratio values and Pb occupation factor. Mg inclusion occurs concomitant with Ph one into PMN perovskite phase and this effect is directed by PbO excess during powder synthesis. (C) 2003 Elsevier B.V. All rights reserved.

The effects of ZnGa2O4 formation on structural and optical properties of ZnO : Ga powders

Gallium-doped zinc oxide (ZnO:Ga 1, 2 3, 4 and 5 at%) samples were prepared in powder form by modifying the Pechini method. The formation of zinc gallate (ZnGa2O4) With the spinel crystal structure was observed even in ZnO:Ga 1 at% by X-ray diffraction. The presence of ZnGa2O4 in ZnO:Ga samples was also evidenced by luminescence spectroscopy through its blue emission at 430 nm, assigned to charge transfer between Ga3+ at regular octahedral symmetry and its surrounding O2- ions. The amount of ZnGa2O4 increases as the dopant concentration increases, as observed by the quantitative phase analysis by the Rietveld method. (C) 2006 Elsevier B.V. All rights reserved.

A oscilação Madden - Julian na Amazônia Oriental: variáveis superfíciais

Tendo como foco as múltiplas escalas de tempo que atuam na Amazônia, este trabalho foi desenvolvido com o objetivo de investigar a possível influencia da Oscilação Madden – Julian (OMJ) em elementos turbulentos da CLP. A OMJ foi identificada a partir de 30 anos de dados de reanálise de radiação de onda longa (ROL) e componente zonal do vento (u). As grandezas turbulentas foram estudadas a partir da variância, covariância e coeficiente de correlação de um conjunto de dados de resposta rápida coletado na torre micrometeorológica de Caxiuanã (PA), e tratados com a Transformada em Ondeletas (TO) para se obter a contribuição de cada escala para estes momentos estatísticos. A análise dos 30 anos de dados de ROL e u mostrou que a ocorrência da OMJ está ligada com o fenômeno do El Niño/Oscilação Sul (ENOS), bem como influência do ENOS no tempo da região amazônica pode estar associado a presença ou não da OMJ. Foi observado que anos de El Niño tendem a desfavorecer a ocorrência da OMJ e anos de La Niña tendem a favorecer o desenvolvimento da oscilação. Caso uma OMJ se desenvolva durante um episodio de El Niño, a oscilação pode influenciar a temperatura, a velocidade do vento e a precipitação de forma diferente ao do El Niño. A análise por fase da OMJ mostrou que, em Belém, há diferença significativa na temperatura máxima e na precipitação entre cada fase, porém, a temperatura mínima e o módulo do vento apresentaram pouca diferença. Os fluxos cinemáticos turbulentos analisados, por escala, em três horários distintos, foram mais diferentes durante o período diurno, principalmente w’T’ e w’q’. A diferença entre fase ativa e fase inativa foi reduzindo com passar do dia, durante o período de transição dia – noite, poucas escalas tiveram diferença significativa, e durante a noite, nenhuma escala teve nível de confiança acima ou igual a 95%. Estes resultados indicam que a convecção diurna é o mecanismo responsável por esta diferença e como a OMJ atua como uma grande célula convectiva, a convecção local é amplificada, explicando a grande diferença observada entre as fases durante o período diurno.

Internal standard for amorphous pharmaceuticals products quantification and an application of Parametric Rietveld refinement using time, temperature and relative humidity as 'non-crystallographic' parameters

Pós-graduação em Química - IQ

Characterization of tetraethylene glycol passivated iron nanoparticles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sr2CeO4: Electronic and structural properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização de cerâmicas a base de nitreto de silício para aplicações estruturais

The need for development of new materials is a natural process in the companies’ technological point of view, seeking improvements in materials and processes. Specifically, among the materials, ceramic exhibit valuable properties, especially the covalent ceramics which have excellent properties for applications which requires the abrasion resistance, hardness, high temperatures, resistence, etc. being a material that has applications in several areas. Most studies are related to improvement of properties, specially fracture toughness that allows the expansion of its application. Among the most promising ceramic materials are silicon nitride (Si3N4) which has excellent properties. The goal of this work was the development and caracterization of Si3N4-based ceramics, doped with yttrium oxide (Y2O3), rar earth concentrate (CTR2O3) and cerium oxide (CeO2) in the same proportion for the evaluation of properties. The powders' mixtures were homogenized, dried and compressed under pressure uniaxial and isostatic. Sintering was carried out in 1850 ⁰C under pressure of 0,1MPa N2 for 1 h with a heating rate of 25 ⁰C / min and cooling in the furnace inertia. The characterizations were performed using Archimedes principle to relative density, weight loss by measuring before and after sintering, phase analysis by X-ray diffraction, microstructure by scanning electron microscope (SEM), hardness and fracture toughness by the method Vickers indentation. The results obtained showed relative density of 97-98%, Vickers hardness 17 to 19 GPa, fracture toughness 5.6 to 6.8 MPa.m1/2, with phases varying from α-SiAlON and β-Si3N4 depending the types of additives used. The results are promising for tribological applications and can be defined according to the types of additives to be used