Los Centros de Colaboración Pedagógica y la técnica de grupos.

Se señalan los principios fundamentales que deben regir la formación y el desarrollo de los grupos de trabajo, que se constituyen en los Centros de Colaboración, para que aseguren unas relaciones más productivas. Para ello, se utiliza la técnica que estudia la dinámica interna y externa de los grupos, que pretende patentizar el juego de opiniones encontradas que enriquecen o empobrecen al grupo, y mostrar, además, el medio de encauzarlas de forma conveniente.

Dielectric properties of process cheese from 0.3 to 3 Ghz

Dielectric properties of 16 process cheeses were determined over the frequency range 0.3-3 GHz. The effect of temperature on the dielectric properties of process cheeses were investigated at temperature intervals of 10 degrees C between 5 and 85 degrees C. Results showed that the dielectric constant decreased gradually as frequency increased, for all cheeses. The dielectric loss factor (epsilon") decreased from above 125 to below 12 as frequency increased. epsilon' was highest at 5 degrees C and generally decreased up to a temperature between 55 and 75 degrees C. epsilon" generally increased with increasing temperature for high and medium moisture/fat ratio cheeses. epsilon" decreased with temperature between 5 and 55 degrees C and then increased, for low moisture/fat ratio cheese. Partial least square regression models indicated that epsilon' and epsilon" could be used as a quality control screening application to measure moisture content and inorganic salt content of process cheese, respectively. (c) 2005 Elsevier Ltd. All rights reserved..

A genealogy of the kings of England in papal Avignon: British Library, Egerton MS. 1500

This is one of three articles in eBLJ (2013) dedicated to the "Abreujamen de las estorias", British Library Egerton MS 1500. The other two articles are: Federico Botana,' The Making of "L'Abreujamen de las estorias": British Library Egerton MS 1500', eblj (2013), article 16. Alexander Ibarz, 'The Provenance of the "Abreujamens de las estorias" (London, British Library, Egerton MS. 1500) and the Identification of Scribal Hands (c. 1323)' eblj (2013), article 17. Leglu's article, eblj (2013), article 18, examines the various political agendas that emerge in the depiction of the kings of Britain and England, from Brutus to Edward II.

Nota científica: métodos para estimativa da area foliar de plantas daninhas: 2: Wissadula subpeltata (Kuntze) Fries

Com o objetivo de obter uma equação que, através de parâmetros lineares dimensionais das folhas, permitisse estimar a área foliar de Wissadula subpeltata (Kuntze) Fries, estudaram- se correlações entre a área foliar real e o comprimento da folha ao longo da nervura principal (C ), largura máxi ma da folha (L) , comprimento do espaço entre o ponto de inserção do pecíolo na folha até a primeira ramificação da nervura principal (CE), L + C, L x C e L x CE. Todas as equações, geométricas ou lineares simples, permitiram boas estimativas da área foliar . do pont o de vista prático, sugere- se optar pela equação linear simples envolvendo o produto C x L, considerando o coeficiente linear igual a zero. Deste modo, a estimativa da área foliar de W. subpeltata pode ser feita pel a fórmula Y = 0, 85 49 (C x L), ou seja 85 ,49% do produto entre o comprimento da nervura principal e a largura máxima da folha.

Segurança das condições de aplicação de herbicidas com aerobarco em plantas daninhas aquáticas no lago da Hidrelétrica de Jupiá

Os objetivos deste trabalho foram quantificar as exposições dérmicas (EDs) e respiratórias (ERs) proporcionadas ao piloto e ao seu ajudante nas aplicações de herbicidas para o controle de plantas daninhas aquáticas com aerobarco; classificar essas condições de trabalho em seguras ou inseguras; e calcular a necessidade de controle das exposições (NCE) e o tempo de trabalho seguro (TTS). O aerobarco utilizado tinha casco de alumínio (4,85 x 2,42 m) e acionamento por hélice acoplada a motor a gasolina de 350 HP. O equipamento de pulverização era composto por bomba de diafragma com fluxo máximo de 49,69 L min-1, pressão máxima de 25 kg cm-2, acionada por motor a gasolina de 4 HP, e tanque de calda de 189 L. A barra de pulverização de alumínio era composta de duas seções laterais de 3 m, posicionadas na linha entre o encosto do banco do piloto e o início da estrutura protetora da hélice. Cada seção da barra tinha seis bicos com pontas de jato plano com indução de ar AI 100 03, espaçados de 0,5 m, e uma ponta OC 20 fixada em cada extremidade. O conjunto de pontas pulverizava faixas de 6 m de largura e aplicava o volume de calda de 200 L ha-1. O sistema tinha gerenciador de fluxo, controlado por central eletrônica acoplada a DGPS (com precisão submétrica), para corrigir automaticamente a vazão em função de alterações na velocidade real da embarcação. As EDs e ERs aos herbicidas foram calculadas com os dados substitutos das exposições às caldas, avaliadas com os traçadores cobre e manganês adicionados às caldas. As exposições foram extrapoladas para uma jornada de trabalho de seis horas. A segurança das condições de trabalho foi determinada com o cálculo da margem de segurança (MS), utilizando-se a fórmula MS = (NOEL x 70)/(QAE x 10), em que QAE = quantidade absorvível da exposição. As condições de trabalho foram classificadas em seguras, se MS>1, ou inseguras, se MS<1. As exposições proporcionadas pelas condições de trabalho foram de 10,65 mL de calda por dia para o piloto e de 16,80 mL por dia para o ajudante, que fica sentado em uma cadeira a 2,0 m à frente do piloto e da barra de pulverização. Classificaram-se como seguras as aplicações dos herbicidas glyphosate (Rodeo, 6 L ha-1), 2,4D (DMA 806 BR, 8 L ha-1) e fluridone (Sonar AQ, 0,4 L ha-1), para o piloto e o seu ajudante. Classificou-se como insegura a aplicação do herbicida diquat (Reward, 4,0 L ha-1) para as duas condições de trabalho, cujas necessidades de controle das exposições calculadas foram de 65% para o piloto e de 78% para o ajudante do piloto.

Métodos de superação de dormência de sementes de barbatimão

The aim of this research was to identify methods for breaking dormancy and promoting germination of Stryphnodendron adstringens and S. polyphyllum seeds. Seeds of both species were submitted to the following treatments for breaking dormancy: control; mechanical scarification (sandpaper number 220); hot water (initial temperature of 87 degrees C) for 5 and 15 minutes; chemical scarification with H(2)SO(4) (95%) for 30, 45, 60, 75, 90 and 105 minutes; thermal shock 1 (0 degrees C and 50% RH for 1 h and thereafter 10 minutes into water Ti=85 degrees C, Tf=57 degrees C); thermic shock 2 (40 degrees C and 40% RH for 6 h and thereafter 10 minutes into water, Ti=0 degrees C, Tf=3 degrees C); thermal shock 3 (40 degrees C and 40% RH for 6h and thereafter 10 minutes into water, Ti=25 degrees C, Tf=25 degrees C). We concluded that seeds belonging to same genus but from different species answered differently to some treatments for breaking dormancy. Chemical scarification with H(2)SO(4) (45 minutes) and mechanical scarification with sandpaper are methods that can be employed with efficiency to break dormancy and promote germination for both species.

Avaliação cinética e potencial do Nb2O5 obtido a partir de um complexo de nióbio para formação do oleato de metila através da reação de esterificação do ácido oleico

Among the heterogeneous catalysts materials made from niobium show up as an alternative to meet the demand of catalysts for biodiesel production. This study aims to evaluate the potential of a heterogeneous catalyst derived from a complex of niobium in the reaction of methyl esterification of oleic acid. The catalyst was synthesized after calcination at different temperatures of a niobium complex ((NH4)3[NbO(C2O4)3].H2O) generating a niobium oxide nanostructure with a different commercial niobium oxide used to synthesize the complex. The commercial niobium oxide, the complex niobium and niobium catalyst were characterized by thermogravimetry (TG and DTA), surface area analysis (BET), scanning electron microscopy (SEM) and X-ray diffraction (XRD), showing the catalyst has researched morphological and crystallographic indicating a catalytic potential higher than that of commercial niobium oxide characteristics. Factorial with central composite design point, with three factors (calcination temperature, molar ratio of alcohol/oleic acid and mass percentage of catalyst) was performed. Noting that the optimal experimental point was given by the complex calcination temperature of 600°C, a molar ratio alcohol/oleic acid of 3.007/1 and the catalyst mass percentage of 7.998%, with a conversion of 22.44% oleic acid in methyl oleate to 60 min of reaction. We performed a composite linear and quadratic regression to determine an optimal statistical point of the reaction, the temperature of calcination of the complex at 450°C, the molar ratio of alcohol/oleic acid 3.3408/1 and mass percentage of catalyst of 7.6833% . Kinetic modeling to estimate parameters for heterogeneous catalysis it set well the experimental results with a final conversion of 85.01% with 42.38% of catalyst and without catalyst at 240 min reaction was performed. Allowing to evaluate the catalyst catalytic studied has the potential to be used in biodiesel production

Aerosol Deposition of Ba0.8Sr0.2TiO3 Thin Films

In this work we optimized conditions for aerosol deposition of homogeneous, nano-grained, smooth Ba0.8Sr0.2TiO3 thin films. Investigation involved optimization of deposition parameters, namely deposition time and temperature for different substrates. Solutions were prepared from titanium isopropoxide, strontium acetate and barium acetate. Films were deposited on Si (1 0 0) or Si covered by platinum (Pt (1 1 1) /Ti/SiO2/Si). Investigation showed that the best films were obtained at substrate temperature of 85 degrees C. After deposition films were slowly heated up to 650 degrees C, annealed for 30 min, and slowly cooled. Grain size of BST films deposited on Si substrate were in the range 40-70 nm, depending on deposition conditions, while the same films deposited on Pt substrates showed mean grain size in the range 35-50 nm. Films deposited under optimal conditions were very homogeneous, crack-free, and smooth with rms roughness lower than 4 nm for both substrates.

Relationship between anxiety and chronic orofacial pain of temporomandibular disorder in a group of university students

Purpose: This study evaluated the relationship between anxiety levels and severity degrees of chronic orofacial pain of temporomandibular disorder in brazilian university students. Methods: 150 volunteers (117 men and 33 women), with age ranging from 17 to 30 years, were subjects to this study. Spielberger's trait-state anxiety inventory was used to evaluate trait and state anxiety of the students, while examination for chronic orofacial pain was performed in accordance with the Research Diagnostic Criteria for Temporomandibular Disorders (RDC/TMD). Association between anxiety levels and severity degrees of chronic orofacial pain was tested using the Chi-square test. The significance level was set at p<.05. Results: The results showed that 32.7% (n = 49) of the subjects exhibited TMD, and the intensity of chronic orofacial pain was classified as degree 1 in 85.7% (n = 42) and as degree 2 in 14.3% (n = 7) of them. Based on the results of the Spielberger's trait-state anxiety inventory, the majority of the students had moderate anxiety (48.6% and 48.1%, respectively). The correlation between trait-anxiety levels and chronic orofacial pain degrees was significant and positive (p<.05). However, no significant correlation was found to state-anxiety levels and chronic orofacial pain degrees (p>.05). Conclusion: It was concluded that chronic orofacial pain of TMD could be present in university students and anxiety may be related. © 2010 Japan Prosthodontic Society. Published by Elsevier Ireland. All rights reserved.

Identificação de espécies e genótipos de Cryptosporidium em bovinos leiteiros no Brasil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estimativas da radiação global incidente em superfícies inclinadas com base na razáo de insolação

Estimating equations of global radiation based on the sunshine duration were proposed for horizontal surface and with inclination of 12.85, 22.85 and 32.85° facing the North in Botucatu, SP, Brazil, in monthly, seasonal and annual groupings of data. Simple linear correlations were applied (for definition of the linear and angular coefficients of Angstrom-Prescott model), in a database measured in all three inclinations in different periods (22.85°: 04/1998 to 07/2001; 12.85°: 08/2011 to 02/2003; and 32.85°: 03/2003 to 12/2007) concomitant with horizontal measures and sunshine duration. The statistical performance of the model was analysed by the means absolute error (MBE), the square root of the mean square error (RMSE) and the index adjustment (d). The minimum global radiation transmissivity varied from 14.35% in August (12.85°) to 27.86% in December (32.85°) and the maximum transmissivity ranged between 62.10% and 78.90%, for June (32.85°) and December (12.85°). Increasing the angle of inclination surface increased the scattering and decreased the index of adjustment and performance. The worst results were found for application of the seasonal and annual models in the months of autumn and winter for 32.85° (RMSE below 42.93% and adjustment superior to 0.4693).

Avaliação do tempo e métodos de aquecimento de toras de Eucalyptus grandis Hill ex-Maiden e sua influência no rendimento em laminação e na qualidade das lâminas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Detecção, epidemiologia e análise molecular de rotavírus, picobirnavírus e reovírus em aves de corte criadas em granjas na mesorregião metropolitana de Belém, Pará, Brasil

Este estudo objetivou investigar a ocorrência de rotavírus aviário (RVA), picobirnavírus (PBV) e reovírus aviário (ARV) em aves de corte criadas em granjas situadas na Mesorregião Metropolitana de Belém, Pará, no período compreendido entre 2008 a 2011. Para tal, foram colhidos 85 pools de amostras fecais provenientes de 37 granjas pertencentes a oito municípios. O RNA viral foi extraído a partir das suspensões fecais e submetido à eletroforese em gel de poliacrilamida (EGPA) seguido da RT-PCR. Foi selecionada pelo menos uma amostra de cada município positivo para o sequenciamento de nucleotídeos dos genes NSP4 (rotavírus), RdRp (picobirnavírus) e S2 (reovírus), sendo que no caso dos picobirnavírus as amostras foram clonadas antes do sequenciamento. A EGPA demonstrou positividade em 0/85 (0%) amostras para RVA do grupo A, 13/85 (15,3%) amostras para PBV e 01/85 (1,2%) amostras para ARV. No caso da RT-PCR foi verificado positividade em 35/85 (41,2%), 42/85 (49,4%) e 28/85 (32,9%) das amostras para RVA, PBV e ARV, respectivamente. Dos oito municípios estudados, sete apresentaram amostras positivas para PBV e seis apresentaram amostras positivas para RVA e ARV. Das 37 granjas estudadas foi observada a presença dessas infecções virais em 19 (51,4%) para RVA e ARV e 21 (56,8%) para PBV. As sequências do gene NSP4 apresentaram entre 86,3 e 90,5% de similaridade ao nível de nucleotídeo (nt) com protótipos de frangos e 93,5 e 100% de similaridade ao nível de nt quando comparadas entre si. As sequências do gene RdRp apresentaram uma grande heterogeneidade genética com variantes gênicas apresentando entre 56,1 e 100% de similaridade ao nível de nt com protótipos pertencentes a várias espécies e fontes de contaminação e entre 50,3 e 100% de similaridade ao nível nt quando comparadas entre si. Na análise das sequências do gene S2 de ARV foi observado entre 90,9 e 94,4% de similaridade ao nível de nt com protótipos de frangos e 90,1 e 100% de similaridade ao nível de nt quando comparadas entre si. Os RVA, PBV e ARV foram detectados em granjas de frangos de corte da Mesorregião Metropolitana de Belém, sendo a detecção por RT-PCR a mais eficiente ao detectar pelo menos um dos vírus nos oito municípios pesquisados. Excetuando-se o PBV, que apresentou relacionamento heterogêneo com os protótipos utilizados, o RVA e ARV deste estudo relacionaram-se especificamente com amostras obtidas em aves. Este é o primeiro estudo envolvendo o sequenciamento gênico do RVA, PBV e ARV em frangos de corte na região norte do Brasil.

Análise microbiológica e físico-química de material proteico comestível derivado do processamento da gordura oriunda do abate de bovinos

Background: The use of all by-products of bovine slaughter is of high economic importance for the industries of products of animal origin. Among these products, fat has an important role, once fat rendering may generate several different products, such as protein material that may be used in the manufacture of meat products. However, in spite of the importance that the use of all by-products has for the economic balance of the industry, there are no reports on their use in Brazil, or studies that supply data on microbiological and physical-chemical local standards for this protein. Thus, the objective of this study was to evaluate microbiological and physical-chemical characteristics of protein material obtained from fat rendering, as well as to provide support for companies to use fat rendering to generate protein material, adding value to industrialized meat products.Materials, Methods & Results: The experimental production of edible protein obtained of fat rendering was conducted in slaughterhouse with supervision of the Brazilian Ministry of Agriculture, Livestock and Food Supply. Protein material was obtained in a continuous, humid heat system at high temperatures. Fat scraps containing protein were ground and cooked at high temperature (85 degrees C), and placed in a three phase decanter centrifuge. After centrifugation, protein material was ground again and packed. Samples were collected from 15 batches of protein material, and the following microbiological analyses were carried out: counts of aerobic mesophilic and psychrotrophic microorganisms, coliforms at 35 degrees C, Escherichia coli, sulfite-reducing Clostridium, and Staphylococcus aureus, besides presence or absence of Salmonella and Listeria monocytogens. The following physical-chemical analyses were also carried out: protein, total lipid, moisture, ash, carbohydrate, and energy content. Mean counts of mesophiles, psychrotrophs, and coliforms at 35 degrees C were 4.17; 3.69 and 1.87 (log CFU/g), respectively. Levels of protein, total lipids, moisture, ashes and carbohydrates were 27.50; 7.83; 63.88%; 0.24%; and 0.55%, respectively, and energy content was 182.63 kcal/100g.Discussion: Results of microbiological analyses demonstrated that, although low, the final product showed to be contaminated. Contamination that occurred during the second grinding procedure may be an explanation for these bacterial counts. Also, the temperature used for fat fusion was not enough to eliminate thermoduric microorganisms. However, even with the presence of indicator microorganisms in the samples, none was contaminated by E. coli, sulfite-reducing Clostridium, S. aureus, Salmonella or L. monocytogenes. Physical-chemical analyses showed that the product had adequate nutritional quality. Based on these results, it was possible to conclude that protein material obtained in fat rendering showed characteristics that enable the use of this product as raw material for processed meat products. Besides, the present study was the first one to present scientific results in relation to edible by-products obtained in fat rendering, supplying important information for slaughterhouses and meat-processing plants. The study also produced relevant data on the innocuousness of the product, which may be used to guide decision-making of health inspectors.