Swirl Flow Bioreactor coupled with Cu-alginate beads: A system for the eradication of Coliform and Escherichia coli from biological effluents

It is estimated that approximately 1.1 billion people globally drink unsafe water. We previously reported both a novel copper-alginate bead, which quickly reduces pathogen loading in waste streams and the incorporation of these beads into a novel swirl flow bioreactor (SFB), of low capital and running costs and of simple construction from commercially available plumbing pipes and fittings. The purpose of the present study was to trial this system for pathogen reduction in waste streams from an operating Dewats system in Hinjewadi, Pune, India and in both simulated and real waste streams in Seattle, Washington, USA. The trials in India, showed a complete inactivation of coliforms in the discharged effluent (Mean Log removal Value (MLRV) = 3.51), accompanied by a total inactivation of E. coli with a MLRV of 1.95. The secondary clarifier effluent also showed a 4.38 MLRV in viable coliforms during treatment. However, the system was slightly less effective in reducing E. coli viability, with a MLRV of 1.80. The trials in Seattle also demonstrated the efficacy of the system in the reduction of viable bacteria, with a LRV of 5.67 observed of viable Raoultella terrigena cells (100%).

A comparison between ultraviolet disinfection and copper alginate beads within a vortex bioreactor for the deactivation of bacteria in simulated waste streams with high levels of colour, humic acid and suspended solids

We show in this study that the combination of a swirl flow reactor and an antimicrobial agent (in this case copper alginate beads) is a promising technique for the remediation of contaminated water in waste streams recalcitrant to UV-C treatment. This is demonstrated by comparing the viability of both common and UV-C resistant organisms in operating conditions where UV-C proves ineffective - notably high levels of solids and compounds which deflect UV-C. The swirl flow reactor is easy to construct from commonly available plumbing parts and may prove a versatile and powerful tool in waste water treatment in developing countries.

The bactericidal effect of dendritic copper microparticles, contained in an alginate matrix, on Escherichia coli

Although the bactericidal effect of copper has been known for centuries, there is a current resurgence of interest in the use of this element as an antimicrobial agent. During this study the use of dendritic copper microparticles embedded in an alginate matrix as a rapid method for the deactivation of Escherichia coli ATCC 11775 was investigated. The copper/alginate produced a decrease in the minimum inhibitory concentration from free copper powder dispersed in the media from 0.25 to 0.065 mg/ml. Beads loaded with 4% Cu deactivated 99.97% of bacteria after 90 minutes, compared to a 44.2% reduction in viability in the equivalent free copper powder treatment. There was no observed loss in the efficacy of this method with increasing bacterial loading up to 10(6) cells/ml, however only 88.2% of E. coli were deactivated after 90 minutes at a loading of 10(8) cells/ml. The efficacy of this method was highly dependent on the oxygen content of the media, with a 4.01% increase in viable bacteria observed under anoxic conditions compared to a >99% reduction in bacterial viability in oxygen tensions above 50% of saturation. Scanning electron micrographs (SEM) of the beads indicated that the dendritic copper particles sit as discrete clusters within a layered alginate matrix, and that the external surface of the beads has a scale-like appearance with dendritic copper particles extruding. E. coli cells visualised using SEM indicated a loss of cellular integrity upon Cu bead treatment with obvious visible blebbing. This study indicates the use of microscale dendritic particles of Cu embedded in an alginate matrix to effectively deactivate E. coli cells and opens the possibility of their application within effective water treatment processes, especially in high particulate waste streams where conventional methods, such as UV treatment or chlorination, are ineffective or inappropriate.

Enhanced Antitumor Activity of the Photosensitizer meso-Tetra(N-methyl-4-pyridyl) Porphine Tetra Tosylate through Encapsulation in Antibody-Targeted Chitosan/Alginate Nanoparticles

meso-Tetra(N-methyl-4-pyridyl) porphine tetra tosylate (TMP) is a photosensitizer that can be used in photodynamic therapy (PDT) to induce cell death through generation of reactive oxygen species in targeted tumor cells. However, TMP is highly hydrophilic, and therefore, its ability to accumulate intracellularly is limited. In this study, a strategy to improve TMP uptake into cells has been investigated by encapsulating the compound in a hydrogel-based chitosan/alginate nanoparticle formulation. Nanoparticles of 560 nm in diameter entrapping 9.1 µg of TMP per mg of formulation were produced and examined in cell-based assays. These particles were endocytosed into human colorectal carcinoma HCT116 cells and elicited a more potent photocytotoxic effect than free drug. Antibodies targeting death receptor 5 (DR5), a cell surface apoptosis-inducing receptor up-regulated in various types of cancer and found on HCT116 cells, were then conjugated onto the particles. The conjugated antibodies further enhanced uptake and cytotoxic potency of the nanoparticle. Taken together, these results show that antibody-conjugated chitosan/alginate nanoparticles significantly enhanced the therapeutic effectiveness of entrapped TMP. This novel approach provides a strategy for providing targeted site-specific delivery of TMP and other photosensitizer drugs to treat colorectal tumors using PDT.

Product standardisation as a tool to control prescribing costs a case study of alginate liquid preparations

Introduction Product standardisation involves promoting the prescribing of pre-selected products within a particular category across a healthcare region and is designed to improve patient safety by promoting continuity of medicine use across the primary/secondary care interface, in addition to cost containment without compromising clinical care (i.e. maintaining safety and efficacy). Objectives To examine the impact of product standardisation on the prescribing of compound alginate preparations within primary care in Northern Ireland. Methods Data were obtained on alginate prescribing from the Northern Ireland Central Services Agency (Prescription Pricing Branch), covering a period of 43 months. Two standardisation promotion interventions were carried out at months 18 and 33. In addition to conventional statistical analyses, a simple interrupted time series analysis approach, using graphical interpretation, was used to facilitate interpretation of the data. Results There was a significant increase in the prescribed share of the preferred alginate product in each of the four health boards in Northern Ireland and a decrease in the cost per Defined Daily Dose for alginate liquid preparations overall. Compliance with the standardisation policy was, however, incomplete and was influenced to a marked degree by the activities of the pharmaceutical industry. The overall economic impact of the prescribing changes during the study was small (3.1%). Conclusion The findings suggested that product standardisation significantly influenced the prescribing pattern for compound alginate liquid preparations within primary care across Northern Ireland. © 2012 The Authors. IJPP © 2012 Royal Pharmaceutical Society.

Preparation of Aqueous Core/Polymer Shell Microcapsules by Internal Phase Separation

Aqueous core/polymer shell microcapsules with mommuclear and polynuclear core morphologies have been formed by internal phase separation from water-in-oil emulsions. The water-in-oil emulsions were prepared with the shell polymer dissolved in the aqueous phase by adding a low boiling point cosolvent. Subsequent removal of this cosolvent (by evaporation) leads to phase separation of the polymer and, if the spreading conditions are correct, formation of a polymer shell encapsulating the aqueous core. Poly(tetrahydrofuran) (PTHF) shell/aqueous core microcapsules, with a single (mononuclear) core, have been prepared, but the low T-g (-84 degreesC) of PTHF makes characterization of the particles more difficult. Poly(methyl methacrylate) and poly(isobutyl methacrylate) have higher T-g values (105 and 55 degreesC, respectively) and can be dissolved in water at sufficiently high acetone concentrations, but evaporation of the acetone from the emulsion droplets in these cases mostly resulted in polynuclear capsules, that is, having cores with many very small water droplets contained within the polymer matrix. Microcapsules with fewer, larger aqueous droplets in the core could be produced by reducing the rate of evaporation of the acetone. A possible mechanism for the formation of these polynuclear cores is suggested. These microcapsules were prepared dispersed in an oil-continuous phase. They could, however, be successfully transferred to a water-continuous phase, using a simple centrifugation technique. In this way, microcapsules with aqueous cores, dispersed in an aqueous medium, could be made. It would appear that a real challenge with the water-core systems, compared to the previous oil-core systems, is to obtain the correct order of magnitude of the three interfacial tensions, between the polymer, the aqueous phase, and the continuous oil phase; these control the spreading conditions necessary to produce shells rather than "acorns".

The effect of alginate-based edible coatings enriched with essential oils constituents on Arbutus unedo L. fresh fruit storage

The effect of coating Arbutus unedo fresh fruit with alginate-based edible coatings enriched with the essential oils compounds (EOC) eugenol (Eug) and citral (Cit) was studied. The minimum inhibitory concentrations (MIC) against the main postharvest pathogens were determined for Eug and Cit giving values of 0.10 and 0.15 (w/v), respectively. Twelve formulations of edible coatings were used: sodium alginate (AL) was tested at 1 and 2% (w/v) with incorporation of Eug and Cit at MIC and double MIC or their combination at MIC. Arbutus berries were dipped in those solutions for 2 min, and then stored at 0.5 degrees C. Control consisted of uncoated fruit. On days 0, 14 and 28, samples were taken to perform physicochemical and biochemical analysis [color CIE (L*, h degrees), firmness, soluble solids content (SSC), weight Loss, trolox equivalent antioxidant capacity (TEAC), microbial growth and taste panels]. Results showed that edible coatings of 1% AL were the best to maintain most quality attributes of the commodity through storage at 0.5 degrees C. The incorporation of Cit and Eug into the alginate edible coatings improved the coatings in most cases, AL 1% + Eug 0.20% and AL 1% + Cit 0.15% + Eug 0.10% being those that better preserved sensory and nutritional attributes and reduced microbial spoilage. Thus, these coatings may be useful for improving postharvest quality and storage life of fresh arbutus fruit. (C) 2014 Elsevier B.V. All rights reserved.

Test and development of microcapsules for rigid polyurethane foam

Tese de mestrado em Química Tecnológica, apresentada à Universidade de Lisboa, através da Faculdade de Ciências, 2016

Immobilisation d'enzymes par microcapsules polymérisées pour le développement de biocapteurs

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal

Fabrication, caractérisation et étude électrochimique de microcapsules conductrices à base de dérivés carbazole aminés pour la conception de biopiles enzymatiques

L’objectif général de cette thèse est de développer une plateforme d’immobilisation d’enzymes efficace pour application en biopile. Grâce à la microencapsulation ainsi qu’au choix judicieux des matériaux polymériques pour la fabrication de la plateforme d’immobilisation, l’efficacité du transfert électronique entre l’enzyme encapsulée et l’électrode serait amélioré. Du même coup, les biopiles employant cette plateforme d’immobilisation d’enzymes pourrait voir leur puissance délivrée être grandement augmentée et atteindre les niveaux nécessaires à l’alimentation d’implants artificiels pouvant remplacer des organes telque le pancréas, les reins, le sphincter urinaire et le coeur. Dans un premier temps, le p-phénylènediamine a été employé comme substrat pour la caractérisation de la laccase encapsulée dans des microcapsules de poly(éthylèneimine). La diffusion de ce substrat à travers les microcapsules a été étudiée sous diverses conditions par l’entremise de son oxidation électrochimique et enzymatique afin d’en évaluer sa réversibilité et sa stabilité. La voltampérométrie cyclique, l’électrode à disque tournante (rotating disk electrode - RDE) et l’électrode à O2 ont été les techniques employées pour cette étude. Par la suite, la famille des poly(aminocarbazoles) et leurs dérivés a été identifée pour remplacer le poly(éthylèneimine) dans la conception de microcapsules. Ces polymères possèdent sur leurs unités de répétition (mono- ou diamino) des amines primaires qui seraient disponibles lors de la polymérisation interfaciale avec un agent réticulant tel qu’un chlorure de diacide. De plus, le 1,8-diaminocarbazole (unité de répétition) possède, une fois polymérisé, les propriétés électrochimiques recherchées pour un transfert d’électrons efficace entre l’enzyme et l’électrode. Il a toutefois été nécessaire de développer une route de synthèse afin d’obtenir le 1,8-diaminocarbazole puisque le protocole de synthèse disponible dans la littérature a été jugé non viable pour être utilisé à grande échelle. De plus, aucun protocole de synthèse pour obtenir du poly(1,8-diaminocarbazole) directement n’a été trouvé. Ainsi, deux isomères de structure (1,6 et 1,8-diaminocarbazole) ont pu être synthétisés en deux étapes. La première étape consistait en une substitution électrophile du 3,6-dibromocarbazole en positions 1,8 et/ou 1,6 par des groupements nitro. Par la suite, une réaction de déhalogénation réductive à été réalisée en utilisant le Et3N et 10% Pd/C comme catalyseur dans le méthanol sous atmosphère d’hydrogène. De plus, lors de la première étape de synthèse, le composé 3,6-dibromo-1-nitro-carbazole a été obtenu; un monomère clé pour la synthèse du copolymère conducteur employé. Finalement, la fabrication de microcapsules conductrices a été réalisée en incorporant le copolymère poly[(9H-octylcarbazol-3,6-diyl)-alt-co-(2-amino-9H-carbazol-3,6-diyl)] au PEI. Ce copolymère a pu être synthétisé en grande quantité pour en permettre son utilisation lors de la fabrication de microcapsules. Son comportement électrochimique s’apparentait à celui du poly(1,8-diaminocarbazole). Ces microcapsules, avec laccase encapsulée, sont suffisamment perméables au PPD pour permettre une activité enzymatique détectable par électrode à O2. Par la suite, la modification de la surface d’une électrode de platine a pu être réalisée en utilisant ces microcapsules pour l’obtention d’une bioélectrode. Ainsi, la validité de cette plateforme d’immobilisation d’enzymes développée, au cours de cette thèse, a été démontrée par le biais de l’augmentation de l’efficacité du transfert électronique entre l’enzyme encapsulée et l’électrode.

Continuous Production of Extracellular L-Glutaminase by Ca-Alginate-Immobilized Marine Beauveria bassiana BTMF S-10 in Packed-Bed Reactor

L-Glutamine amidohydrolase (L-glutaminase, EC 3.5.1.2) is a therapeutically and industrially important enzyme. Because it is a potent antileukemic agent and a flavor-enhancing agent used in the food industry, many researchers have focused their attention on L-glutaminase. In this article, we report the continuous production of extracellular L-glutaminase by the marine fungus Beauveria bassiana BTMF S-10 in a packed-bed reactor. Parameters influencing bead production and performance under batch mode were optimized in the order-support (Na-alginate) concentration, concentration of CaCl2 for bead preparation, curing time of beads, spore inoculum concentration, activation time, initial pH of enzyme production medium, temperature of incubation, and retention time. Parameters optimized under batch mode for L-glutaminase production were incorporated into the continuous production studies. Beads with 12 × 108 spores/g of beads were activated in a solution of 1% glutamine in seawater for 15 h, and the activated beads were packed into a packed-bed reactor. Enzyme production medium (pH 9.0) was pumped through the bed, and the effluent was collected from the top of the column. The effect of flow rate of the medium, substrate concentration, aeration, and bed height on continuous production of L-glutaminase was studied. Production was monitored for 5 h in each case, and the volumetric productivity was calculated. Under the optimized conditions for continuous production, the reactor gave a volumetric productivity of 4.048 U/(mL·h), which indicates that continuous production of the enzyme by Ca-alginate-immobilizedspores is well suited for B. bassiana and results in a higher yield of enzyme within a shorter time. The results indicate the scope of utilizing immobilized B. bassiana for continuous commercial production of L-glutaminase

In vitro fermentation and prebiotic potential of novel low molecular weight polysaccharides derived from agar and alginate seaweeds

Fermentation properties and prebiotic potential of novel low molecular weight polysaccharides (LMWPs) derived from agar and alginate bearing seaweeds was investigated. Ten LMWPs were supplemented to pH, temperature controlled anaerobic batch cultures inoculated with human feces from three donors, in triplicate. Microbiota changes were monitored using Fluorescent in-situ hybridization and short chain fatty acids, the fermentation end products were analysed using gas chromatography. Of the ten LMWPs tested, Gelidium seaweed CC2253 of molecular weight 64.64 KDa showed a significant increase in bifidobacterial populations from log(10) 8.06 at 0 h to log(10) 8.55 at 24 h (p = 0.018). For total bacterial populations, alginate powder CC2238 produced a significant increase from log(10) 9.01 at 0 h to log(10) 9.58 at 24 h (p = 0.032). No changes were observed in the other bacterial groups tested viz. Bacteroides, Lactobacilli/Enterococci, Eubacterium rectale/Clostridium coccoides and Clostridium histolyticum. The polysaccharides also showed significant increases in total SCFA production, particularly acetic and propionic acids, indicating that they were readily fermented. In conclusion, some LMWPs derived from agar and alginate bearing seaweeds were fermented by gut bacteria and exhibited potential to be used a novel source of prebiotics.