Evaluating the effect of dislocation on the photovoltaic performance of metamorphic tandem solar cells

The photovoltaic conversion efficiency for monolithic GaInP/GaInAs/Ge triple-junction cell with various bandgap combination (300 suns, AM1.5d) was theoretically calculated. An impressive improvement on conversion efficiency was observed for a bandgap combination of 1.708, 1.194, and 0.67 eV. A theoretical investigation was carried out on the effect of dislocation on the metamorphic structure's efficiency by regarding dislocation as minority-carrier recombination center. The results showed that only when dislocation density was less than 1.6x10(6) cm(-2), can this metamorphic combination exhibit its efficiency advantage over the fully-matched combination. In addition, we also briefly evaluated the lattice misfit dependence of the dislocation density for a group of metamorphic triple-junction system, and used it as guidance for the choice of the proper cell structure.

Microcrystalline silicon films and tandem solar cells prepared by triode PECVD

This paper investigates the effects of the diphasic structure on the optoelectronic properties of hydrogenated microcrystalline silicon (mu c-Si:H) films prepared in a triode three-chamber plasma-enhanced chemical vapor deposition (PECVD) system. The influences of boron-compensation doping on the dark-and photo-conductivity of mu c-Si:H films are also described. A tandem solar cell with an entirely mu c-Si:H p-i-n bottom cell and an a-Si:H top cell has been prepared with an initial conversion efficiency of 8.91% (0.126 cm(2), AM1.5, 100 mW/cm(2)).

Boron-doped silicon film as a recombination layer in the tunnel junction of a tandem solar cell

Boron-doped hydrogenated silicon films with different gaseous doping ratios (B_2H_6/SiH_4) were deposited in a plasma-enhanced chemical vapor deposition (PECVD) system. The microstructure of the films was investigated by atomic force microscopy (AFM) and Raman scattering spectroscopy. The electrical properties of the films were characterized by their room temperature electrical conductivity (σ) and the activation energy (E_a). The results show that with an increasing gaseous doping ratio, the silicon films transfer from a microcrystalline to an amorphous phase, and corresponding changes in the electrical properties were observed. The thin boron-doped silicon layers were fabricated as recombination layers in tunnel junctions. The measurements of the Ⅰ-Ⅴ characteristics and the transparency spectra of the junctions indicate that the best gaseous doping ratio of the recombination layer is 0.04, and the film deposited under that condition is amorphous silicon with a small amount of crystallites embedded in it. The junction with such a recombination layer has a small resistance, a nearly ohmic contact, and a negligible optical absorption.

Thermal analysis and test for single concentrator solar cells

A thermal model for concentrator solar cells based on energy conservation principles was designed. Under 400X concentration with no cooling aid, the cell temperature would get up to about 1200℃.Metal plates were used as heat sinks for cooling the system, which remarkably reduce the cell temperature. For a fixed concentration ratio, the cell temperature reduced as the heat sink area increased. In order to keep the cell at a constant temperature, the heat sink area needs to increase linearly as a function of the concentration ratio. GaInP/GaAs/Ge triple-junction solar cells were fabricated to verify the model. A cell temperature of 37℃ was measured when using a heat sink at 400X concentratration.

General design of the CSR project in IMP

CSR, a new accelerator project under the construction. to upgrade the existing heavy ion cyclotron system in Lanzhou, is a double cooling-storage-ring system. It consists of a main ring and an experimental ring. The heavy ion beams from the cyclotron system will be accumulated and accelerated first in the main ring, then extracted to produce radioactive ion beams or high-Z beams, and finally to be send to the second ring for internal-target experiments.

ADVANCED ELECTROANALYTICAL CHEMISTRY IN CHINA .1. GENERAL ASPECT AND SOME METHODOLOGIES

The Research on Electroanalytical chemistry in China started mainly from the beginning of new China in 1949. It has already good basis and development nowadays. A review with references to the end of seventies has been published in "Reviews in Analytical Chemistry" 1) and in a book titled "Fifty years of Chinese Chemistry" edited by the Chinese Chemical Society in 1985 2). Since then more than thousand papers have been published, and it is impossible and also not necessary to describe all of them. This review only deals with the main progress of electroanalytical chemistry in China in recent years. Some new developed methodologies will be reviewed by S. Dong in the next article.

Identification and characterization of the AcrR/AcrAB system of a pathogenic Edwardsiella tarda strain

Edwardsielia tarda is one of the leading marine pathogens that can infect a wide range of cultured marine species. In this study, the acrR-acrAB cluster was cloned from TX1, a pathogenic E. tarda strain isolated from diseased fish. AcrR and AcrAB were found to be involved in resistance against acriflavine and methyl viologen, which positively regulate the expression of acrAB. AcrR negatively regulates its own expression and the expression of the acrAB operon, most likely by interacting with a 24-bp operator site that overlaps the putative promoter of acrA (PacrA). The repressive effect of AcrR on PacrA could be relieved by acriflavine, methyl viologen, and ethidium bromide, the presence of each of which enhanced transcription from PacrA. Interruption of the regulated expression of acrR by introducing into TX1 a plasmid that overexpresses acrR affected growth under stress conditions, AI-2 production, and bacterial virulence. In addition, mutational analyses identified a constitutively active AcrR mutant (named N215), which exhibits full repressor activity but is impaired in its ability to interact with the inducer. Overexpression of N215 produced the same kind of but moderately stronger effect on TX1 compared to that produced by overexpression of the wild-type acrR.

Temperature and light tolerance of representative brown, green and red algae in tumble culture revealed by chlorophyll fluorescence measurements

Laminaria japonica, Undaria pinnatifida, Ulva lactuca, Grateloupia turuturu and Palmaria palmata are Suitable species that fit the requirements of a seaweed-animal integrated aquaculture system in terms of their viable biomass, rapid growth and promising nutrient uptake rates. fit this investigation, the responses of the optimal chlorophyll fluorescence yield of the five algal species in tumble Culture were assessed at a temperature range of 10 similar to 30 degrees C. The results revealed that Ulva lactuca was the most resistant species to high temperature, withstanding 30 degrees C for 4 h without apparent decline in the optimal chlorophyll fluorescence yield. While the arctic alga Palmaria palmata was the most vulnerable one, showing significant decline in the optimal chlorophyll fluorescence yield at 25 degrees C for 2 h. The cold-water species Laminaria japonica, however, demonstrated strong ability to cope with higher temperature (24 similar to 26 degrees C) for shorter time (within 24 h) without significant decline in the optimal chlorophyll fluorescence yield. Grateloupia turuturu showed a general decrease in the optimal chlorophyll fluorescence yield with the rising temperature from 23 to 30 degrees C, similar to the temperate kelp Undaria pinnatifida. Changes of chlorophyll fluorescence yields of these algae were characterized differently indicating the existence of species-unique strategy to cope with high light. Measurements of the optimal chlorophyll fluorescence yield after short exposure to direct solar irradiance revealed how long these exposures could be without significant photoinhibition or with promising recovery in photosynthetic activities. Seasonal pattern of alternation of algal species in tank culture in the Northern Hemisphere at the latitude of 36 degrees N was proposed according to these basic measurements.

Dynamic changes of total bacteria and Vibrio in an integrated seaweed-abalone culture system

Polyculture of seaweeds alongside fed animal aquaculture is an environmentally friendly means of avoiding eutrophication problem both in land-based and sea-based monoculture systems. Many aspects of such polyculture systems have been described, but little attention has been given to the impact of live seaweeds on the microbiological properties of the water that connects the algae and animals. In this investigation, the Pacific red alga Gracilaria textorii was cultured in a recirculated dual tank system (150 L) with the juvenile abalone Haliotis discus hannai. Dynamic changes of total bacteria (TB) and total Vibrio (TV) in the water of polyculture and monoculture systems were evaluated. Results revealed that (1) level of TB in the polyculture was constantly higher than in the monoculture over a 6.5-day period. While levels of TV in the polyculture was detected to be constantly lower than in the monoculture, (2) integration of G. textorii in the abalone culture changed the Vibrio compositions in the water as judged by the changes of bacteria colony types; (3) application of artificial diet led to dramatic increase of the levels in TB and TV in both systems at 12 h after application in the 24-h test and resulted in selective propagation of Vibrio in the water in the monoculture system; (4) polyculture of G. textorii with juvenile abalone in combination with feeding with live algal diet helped to maintain low levels of TV and the balance of the Vibrio composition; (5) living biomass of G. textorii was effective in preventing propagation of two purified Vibrio strains (V alginolaticus and V logei) in the water. These results provide a general basis of the dynamic changes of levels in TB and TV in a seaweed-abalone polyculture system with or without artificial diet in tanks. (c) 2005 Elsevier B.V All rights reserved.

Influence of the earth rotation on the interfacial wave solutions and wave-induced tangential stress in a two-layer fluid system

Interfacial waves and wave-induced tangential stress are studied for geostrophic small amplitude waves of two-layer fluid with a top free surface and a flat bottom. The solutions were deduced from the general form of linear fluid dynamic equations of two-layer fluid under the f-plane approximation, and wave-induced tangential stress were estimated based on the solutions obtained. As expected; the solutions derived from the present work include as special cases those obtained by Sun et al. (2004. Science in China, Set. D, 47(12): 1147-1154) for geostrophic small amplitude surface wave solutions and wave-induced tangential stress if tire density of the upper layer is much smaller than that of the lower layer. The results show that the interface and the surface will oscillate synchronously, and the influence of the earth's rotation both on the surface wave solutions and the interfacial wave solutions should be considered.

SodaBot: A Software Agent Environment and Construction System

This thesis presents SodaBot, a general-purpose software agent user-environment and construction system. Its primary component is the basic software agent --- a computational framework for building agents which is essentially an agent operating system. We also present a new language for programming the basic software agent whose primitives are designed around human-level descriptions of agent activity. Via this programming language, users can easily implement a wide-range of typical software agent applications, e.g. personal on-line assistants and meeting scheduling agents. The SodaBot system has been implemented and tested, and its description comprises the bulk of this thesis.

A Lifetime-based Garbage Collector for LISP Systems on General-Purpose Computers

Garbage collector performance in LISP systems on custom hardware has been substantially improved by the adoption of lifetime-based garbage collection techniques. To date, however, successful lifetime-based garbage collectors have required special-purpose hardware, or at least privileged access to data structures maintained by the virtual memory system. I present here a lifetime-based garbage collector requiring no special-purpose hardware or virtual memory system support, and discuss its performance.

Computer System for Visual Recognition Using Active Knowledge

A system for visual recognition is described, with implications for the general problem of representation of knowledge to assist control. The immediate objective is a computer system that will recognize objects in a visual scene, specifically hammers. The computer receives an array of light intensities from a device like a television camera. It is to locate and identify the hammer if one is present. The computer must produce from the numerical "sensory data" a symbolic description that constitutes its perception of the scene. Of primary concern is the control of the recognition process. Control decisions should be guided by the partial results obtained on the scene. If a hammer handle is observed this should suggest that the handle is part of a hammer and advise where to look for the hammer head. The particular knowledge that a handle has been found combines with general knowledge about hammers to influence the recognition process. This use of knowledge to direct control is denoted here by the term "active knowledge". A descriptive formalism is presented for visual knowledge which identifies the relationships relevant to the active use of the knowledge. A control structure is provided which can apply knowledge organized in this fashion actively to the processing of a given scene.

Changes in innovation styles - comprehensive study of the changes in innovation styles to identify the causes and effects of different influencing factors and capabilities to create a general innovation pattern.

An investigation in innovation management and entrepreneurial management is conducted in this thesis. The aim of the research is to explore changes of innovation styles in the transformation process from a start-up company to a more mature phase of business, to predict in a second step future sustainability and the probability of success. As businesses grow in revenue, corporate size and functional complexity, various triggers, supporters and drivers affect innovation and company's success. In a comprehensive study more than 200 innovative and technology driven companies have been examined and compared to identify patterns in different performance levels. All of them have been founded under the same formal requirements of the Munich Business Plan Competition -a research approach which allowed a unique snapshot that only long-term studies would be able to provide. The general objective was to identify the correlation between different factors, as well as different dimensions, to incremental and radical innovations realised. The 12 hypothesis were formed to prove have been derived from a comprehensive literature review. The relevant academic and practitioner literature on entrepreneurial, innovation, and knowledge management as well as social network theory revealed that the concept of innovation has evolved significantly over the last decade. A review of over 15 innovation models/frameworks contributed to understand what innovation in context means and what the dimensions are. It appears that the complex theories of innovation can be described by the increasing extent of social ingredients in the explanation of innovativeness. Originally based on tangible forms of capital, and on the necessity of pull and technology push, innovation management is today integrated in a larger system. Therefore, two research instruments have been developed to explore the changes in innovations styles. The Innovation Management Audits (IMA Start-up and IMA Mature) provided statements related to product/service development, innovativeness in various typologies, resources for innovations, innovation capabilities in conjunction to knowledge and management, social networks as well as the measurement of outcomes to generate high-quality data for further exploration. In obtaining results the mature companies have been clustered in the performance level low, average and high, while the start-up companies have been kept as one cluster. Firstly, the analysis exposed that knowledge, the process of acquiring knowledge, interorganisational networks and resources for innovations are the most important driving factors for innovation and success. Secondly, the actual change of the innovation style provides new insights about the importance of focusing on sustaining success and innovation ii 16 key areas. Thirdly, a detailed overview of triggers, supporters and drivers for innovation and success for each dimension support decision makers in putting their company in the right direction. Fourthly, a critical review of contemporary strategic management in conjunction to the findings provides recommendation of how to apply well-known management tools. Last but not least, the Munich cluster is analysed providing an estimation of the success probability of the different performance cluster and start-up companies. For the analysis of the probability of success of the newly developed as well as statistically and qualitative validated ICP Model (Innovativeness, Capabilities & Potential) has been developed and applied. While the model was primarily developed to evaluate the probability of success of companies; it has equal application in the situation to measure innovativeness to identify the impact of various strategic initiatives within small or large enterprises. The main findings of the model are that competitor, and customer orientation and acquiring knowledge important for incremental and radical innovation. Formal and interorganisation networks are important to foster innovation but informal networks appear to be detrimental to innovation. The testing of the ICP model h the long term is recommended as one subject of further research. Another is to investigate some of the more intangible aspects of innovation management such as attitude and motivation of mangers. IV

LOCALIZED ENHANCEMENTS OF Fe+10 DENSITY IN THE CORONA AS OBSERVED IN Fe xi 789.2 nm DURING THE 2006 MARCH 29 TOTAL SOLAR ECLIPSE

Habbal, Shadia Rifai; Morgan, Huw; Johnson, Judd; Arndt, Martina Belz; Daw, Adrian; Jaeggli, Sarah; Kuhn, Jeff; Mickey, Don, LOCALIZED ENHANCEMENTS OF Fe+10 DENSITY IN THE CORONA AS OBSERVED IN Fe xi 789.2 nm DURING THE 2006 MARCH 29 TOTAL SOLAR ECLIPSE, The Astrophysical Journal, Volume 663, Issue 1, pp. 598-609