991 resultados para nearly-stoichiometric LiTaO3
Resumo:
The deterioration of the mechanical properties of bone with age is related to several factors including the structure, organization and chemistry of the constituent phases; however, the relative contribution of each of these factors is not well understood. In this study, we have investigated the effect of chemistry (calcium deficiency) on the mechanical properties of single crystals of hydroxyapatite. Single crystals of stoichiometric crystals grown by the flux method and calcium-deficient platelet crystals grown using wet chemical methods were used as model systems. Using nanoindentation, we show that calcium deficiency leads to an 80% reduction in the hardness and elastic modulus and at least a 75% reduction in toughness in plate-shaped hydroxyapatite crystals. Measurement of local mechanical properties using nanoindentation and nanoscale chemistry through elemental mapping in a transmission electron microscope points to a direct correlation between the observed spatial variation in composition and the large scatter in the measured hardness and modulus values. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Resumo:
Members of the receptor-guanylate cyclase (rGC) family possess an intracellular catalytic domain that is regulated by an extracellular receptor domain. GC-C, an intestinally expressed rGC, was initially cloned by homology as an orphan receptor. The search for its Ligands has yielded three candidates: STa (a bacterial toxin that causes traveler's diarrhea) and the endogenous peptides uroguanylin and guanylin. Here, by performing Northern and Western blots, and by measuring [I-125]STa binding and STa-dependent elevation of cGMP levels, we investigate whether the distribution of GC-C matches that of its endogenous ligands in the rat intestine. We establish that 1) uroguanylin is essentially restricted to small bowel; 2) guanylin is very low in proximal small bowel, increasing to prominent levels in distal small bowel and throughout colon; 3) GC-C messenger RNA and STa-binding sites are uniformly expressed throughout the intestine; and 4) GC-C-mediated cGMP synthesis peaks at the proximal and distal extremes of the intestine (duodenum and colon), but is nearly absent in the middle (ileum). These observations suggest that GC-C's activity may be posttranslationally regulated, demonstrate that the distribution of GC-C is appropriate to mediate the actions of both uroguanylin and guanylin, and help to refine current hypotheses about the physiological role(s) of these peptides.
Resumo:
Internal structures of extraordinarily luminescent semiconductor nanoparticles are probed with photoelectron spectroscopy, establishing a gradient alloy structure as an essential ingredient for the observed phenomenon. Comparative photoluminescence lifetime measurements provide direct evidence for a minimization of nonradiative decay channels because of the removal of interfacial defects due to a progressive change in the lattice parameters in such graded structures, exhibiting a nearly single exponential decay Quantum mechanical, calculations suggest a differential extent of spatial collapse of the electron and the hole wave functions in a way that helps to enhance the photoluminescence efficiency, while at the same time increasing the lifetime of the excited state, as observed in the experiments.
Resumo:
The photoacoustic technique is used to determine the optical energy gap E0 of bulk SixTe100−x glasses in the glass-forming region 10 ≤ x ≤ 28. The thermal diffusivity α of these samples has also been measured. The variation of E0 and α with x is reported. It is found that E0 increases with x nearly linearly with a sharp decrease in the rate of increase beyond x = 20. The thermal diffusivity also increases with x up to x = 20 but decreases for compositions with higher values of x. The observed behaviour is explained on the basis of a chemical bond approach. It is accounted for in terms of the increase in the number of Te---Te bonds and formation of SiTe4 tetrahedra with an increase in the chalcogen content.
Resumo:
The Intergovernmental Panel on Climate Change (IPCC) has successfully produced four assessment reports since 1990 along with a number of special reports and greenhouse gas inventory guidelines. It has very rigorous and robust procedures and guidelines for preparing the assessment reports largely based on synthesis of peer-reviewed and published scientific literature. IPCC has attracted controversy since the Second Assessment Report of 1995. The recent controversies surrounding the IPCC reports surfaced nearly two years after the release of the report in 2007, especially in the wake of the crucial Copenhagen Climate Convention. Many of the controversies can be traced to the use of information sourced from reports published outside the scientific journals such as reports of the World Wildlife Fund. It is true that there are a few errors in the IPCC reports, which may have escaped the multilayered rigorous review process. Many of the errors found in the main reports, which are over a thousand page each, have not been quoted in the crucial and most referred Summary for Policy Makers. IPCC may have to develop a more robust policy for sourcing literature published outside the scientific journals. The United Nations Secretary General has requested the prestigious Inter-Academy Council to review the IPCC principles, procedures and guidelines. The controversies raised in the recent past do not in any way change the main conclusions of the IPCC Assessment Report.
Resumo:
We report numerical results for the phase diagram in the density-disorder plane of a hard-sphere system in the presence of quenched, random, pinning disorder. Local minima of a discretized version of the Ramakrishnan-Yussouff free energy functional are located numerically and their relative stability is studied as a function of the density and the strength of disorder. Regions in the phase diagram corresponding to liquid, glassy, and nearly crystalline states are mapped out, and the nature of the transitions is determined. The liquid to glass transition changes from first to second order as the strength of the disorder is increased. For weak disorder, the system undergoes a first-order crystallization transition as the density is increased. Beyond a critical value of the disorder strength, this transition is replaced by a continuous glass transition. Our numerical results are compared with those of analytical work on the same system. Implications of our results for the field-temperature phase diagram of type-II superconductors are discussed.
Resumo:
Perfectly hard particles are those which experience an infinite repulsive force when they overlap, and no force when they do not overlap. In the hard-particle model, the only static state is the isostatic state where the forces between particles are statically determinate. In the flowing state, the interactions between particles are instantaneous because the time of contact approaches zero in the limit of infinite particle stiffness. Here, we discuss the development of a hard particle model for a realistic granular flow down an inclined plane, and examine its utility for predicting the salient features both qualitatively and quantitatively. We first discuss Discrete Element simulations, that even very dense flows of sand or glass beads with volume fraction between 0.5 and 0.58 are in the rapid flow regime, due to the very high particle stiffness. An important length scale in the shear flow of inelastic particles is the `conduction length' delta = (d/(1 - e(2))(1/2)), where d is the particle diameter and e is the coefficient of restitution. When the macroscopic scale h (height of the flowing layer) is larger than the conduction length, the rates of shear production and inelastic dissipation are nearly equal in the bulk of the flow, while the rate of conduction of energy is O((delta/h)(2)) smaller than the rate of dissipation of energy. Energy conduction is important in boundary layers of thickness delta at the top and bottom. The flow in the boundary layer at the top and bottom is examined using asymptotic analysis. We derive an exact relationship showing that the a boundary layer solution exists only if the volume fraction in the bulk decreases as the angle of inclination is increased. In the opposite case, where the volume fraction increases as the angle of inclination is increased, there is no boundary layer solution. The boundary layer theory also provides us with a way of understanding the cessation of flow when at a given angle of inclination when the height of the layer is decreased below a value h(stop), which is a function of the angle of inclination. There is dissipation of energy due to particle collisions in the flow as well as due to particle collisions with the base, and the fraction of energy dissipation in the base increases as the thickness decreases. When the shear production in the flow cannot compensate for the additional energy drawn out of the flow due to the wall collisions, the temperature decreases to zero and the flow stops. Scaling relations can be derived for h(stop) as a function of angle of inclination.
Resumo:
Members of the PrBa2Cu3O7–delta system possessing the orthorhombic structure over a wide range of oxygen stoichiometry (delta=–0.5 to +0.5) have been prepared and characterized. Similar compositions with a tetragonal structure have also been prepared. None of the oxides is superconducting, independent of the structure or stoichiometry. Praseodymium seems to be present to a small extent in the 4+ state in oxygen-excess (negative delta) samples. Orthorhombic PrBa2Cu3O7–delta samples show the presence of twins suggesting that twins arise from orthorhombicity and have no relation to the superconductivity. A neutron diffraction study of a near-stoichiometric sample has shown a disordered orthorhombic structure with 72% occupancy of the 01 (chain) sites and with no interchange between Pr and Ba sites.
Resumo:
Long-range transport of continental dust makes these particles a significant constituent even at locations far from their sources. It is important to study the temporal variations in dust loading over desert regions and the role of meteorology, in order to assess its radiative impact. In this paper, infrared radiance (10.5-12.5 mu m), acquired by the METEOSAT-5 satellite (similar to 5-km resolution) during 1999 and 2003 was used to quantify wind dependence of dust aerosols and to estimate the radiative forcing. Our analysis shows that the frequency of occurrence of dust events was higher during 2003 compared to 1999. Since the dust production function depends mainly on the surface wind speed over regions which are dry and without vegetation, the role of surface wind on IDDI was examined in detail. It was found that an increase of IDDI with wind speed was nearly linear and the rate of increase in IDDI with surface wind was higher during 2003 compared to 1999. It was also observed that over the Indian desert, when wind speed was the highest during monsoon months (June to August), the dust production rate was lower because of higher soil moisture (due to monsoon rainfall). Over the Arabian deserts, when the wind speed is the highest during June to August, the dust production rate is also highest, as soil moisture is lowest during this season. Even though nothing can be said precisely on the reason why 2003 had a greater number of dust events, examination of monthly mean soil moisture at source regions indicates that the occurrence of high winds simultaneous with high soil moisture could be the reason for the decreased dust production efficiency in 1999. It appears that the deserts of Northwest India are more efficient dust sources compared to the deserts of Saudi Arabia and Northeast Africa (excluding Sahara). The radiative impact of dust over various source regions is estimated, and the regionally and annually averaged top of the atmosphere dust radiative forcing (short wave, clear-sky and over land) over the entire study region (0-35 degrees N; 30 degrees-100 degrees E) was in the range of -0.9 to +4.5 W m(-2). The corresponding values at the surface were in the range of -10 to -25 W m(-2). Our studies demonstrate that neglecting the diurnal variation of dust can cause errors in the estimation of long wave dust forcing by as much as 50 to 100%, and nighttime retrieval of dust can significantly reduce the uncertainties. A method to retrieve dust aerosols during nighttime is proposed. The regionally and annually averaged long wave dust radiative forcing was +3.4 +/- 1.6 W m(-2).
Resumo:
A commercial acrylic fiber with 92% (w/w) acrylonitrile content was partially hydrolyzed converting a fraction of the nitrile (-CN) groups to carboxylic acid (-COOH) groups, to coat the fiber with polyethylenimine (PEI) resin, which was then crosslinked with glutaraldehyde and further quaternized with ethyl chloroacetate to produce a novel strong-base anionic exchanger in the form of fiber. Designated as PAN(QPEI.XG)(Cl-), the fibrous sorbent was compared with a commercial bead-form resin Amberlite IRA-458(Cl-) in respect of sorption capacity, selectivity, and kinetics for removal of silver thiosulfate complexes from aqueous solutions. Though the saturation level of [Ag(S2O3)(2)](3-) on PAN(QPEI.XG)(Cl-) is considerably less than that on IRA-458(Cl-), the gel-coated fibrous sorbent exhibits, as compared to the bead-form sorbent, a significantly higher sorption selectivity for the silver thiosulfate complex in the presence of excess of other anions Such as S2O32-, SO42-, and Cl-, and a remarkably faster rate of both sorption and stripping. The initial uptake of the sorbate by the fibrous sorbent is nearly instantaneous, reaching up to similar to 80% of the saturation capacity within 10 s, as compared to only similar to 12% on the bead-form sorbent. The high initial rate of uptake fits a shell-core kinetic model for sorption on fiber of cylindrical geometry. With 4M HCl, the stripping of the sorbed silver complex from the fibrous sorbent is clean and nearly instantaneous, while, in contrast, a much slower rate of stripping on the bead-form sorbent leads to its fouling due to a slow decomposition of the silver thiosulfate complex in the acidic medium.
Resumo:
A solid solution of the type Ba5x/2Bi(1-x)5/3Nb5O15 has been identified in the BaO-Bi2O3-Nb2O5 system for the first time. The limits of the solid solution are within the range 0.52 <= x <= 0.80. The compositions x = 0.52, 0.60, 0.72, 0.77, 0.78, and 0.80 were synthesized by the solid-state technique from the starting materials in stoichiometric quantities. The powder X-ray patterns of all the phases in the domain indicate a structural similarity to tetragonal tungsten bronzes (TTBs). The compositions below x = 0.52 and those above x = 0.80 exhibit barium niobate and bismuth niobate impurities, respectively. Single crystals of the composition x = 0.77 were obtained by the melt cooling technique. The crystal structure of Ba3.85/2Bi1.15/3Nb5O15 (x = 0.77) was solved in the tetragonal space group P4bm (No. 100) with a = 12.4938 (14) angstrom, c = 3.9519 (2) A, V = 616.87 (10) angstrom(3), and Z = 2 and was refined to an R index of 0.034. Dielectric measurements on all the phases indicate a typical relaxor behavior with a broad phase transition at T-m approximate to 300 K.
Resumo:
The compound Bi3W2O10.5 was synthesized by the solid-state technique from Bi2O3 and WO3 in stoichiometric quantities. Single crystals were grown by the melt-cooling technique and the crystal structure was solved in the tetragonal 141in space group with a = 3.839 (1) A, c = 16-3S2 (5) A, V = 241.4 (1) angstrom(3), Z = 4 and was refined to an R index of 0.0672. The structure represents a modification of the Aurivillius phase and consists of [Bi2O2](2+) units separated by WO8 polyhedra. a.c. impedance studies indicate oxide ion conductivity of 2.91 10(-5) cm(-1) at 600 degrees C.
Resumo:
We report a simple modified polymeric precursor route for the synthesis of highly crystalline and homogenous nanoparticles of lanthanum calcium manganese oxide (LCMO). The LCMO phase formation was studied by thermal analysis, x-ray powder diffraction, and infrared spectroscopy at different stages of heating. These nanocrystallites (average particle size of 30 nm) possess ferromagnetic-paramagnetic transition temperature (T-c) of 300 K, nearly 50 K higher than that of a single crystal. The Rietveld analysis of the powder x-ray diffraction data of the nanopowders reveals significant lattice contraction and reduction in unit cell anisotropy-these structural changes are correlated to the enhancement in T-c.
Resumo:
The reactivity of Grignard reagents towards imines in the presence of catalytic and stoichiometric amounts of titanium alkoxides is reported.Alkylation, reduction, and coupling of imines take place. Whereas reductive coupling is the major reaction in stoichiometric reactions, alkylation is favored in catalytic reactions. Mechanistic studies clearly indicate that intermediates involved in the two reactions are different. Catalytic reactions involve a metal alkyl complex. This has been confirmed by reactions of deuterium-labeled substrates and different alkylating agents. Under the stoichiometric conditions, however, titanium olefin complexes are formed through reductive elimination, probably through a multinuclear intermediate.
Resumo:
Länsimaat ovat rahoittaneet kehitysyhteistyöhankkeita jo lähes kuuden vuosikymmenen ajan, mutta kehitysavun tehokkuudesta ei olla edelleenkään päästy yksimielisyyteen. Yksi avunantajamaiden tapa vaikuttaa kehitysavun tehokkuuteen, eli avun vaikutukseen vastaanottajamaan taloudellisen kasvun kiihdyttäjänä, on sitoa ne julkisen sektorin infrastruktuurihankkeisiin. Joissain tapauksissa tämä vaikuttaa avun vastaanottajan käytökseen ja asenteisiin kehitysapua kohtaan. Tutkielmassa käsitellään kehitysavun tehokkuutta tilanteessa, jossa se on sidottu julkisen sektorin investointeihin kehitysmaassa. Tutkimus pohjaa Kalaitzidakisin ja Kalyvitisin (2008) malliin, jossa osa kehitysmaan julkisen talouden investoinneista rahoitetaan kehitysavulla. Seuraavaksi tarkastellaan ylijäämää tavoittelevan käyttäytymisen (rent- seeking) vaikutusta kehitysavun tehokkuuteen pohjaten Economidesin, Kalyvitisin ja Philippopoulosin (2008) malliin. Tutkielmassa referoidaan lisäksi tutkimuskysymystä sivuavia empiirisiä tutkimuksia, esitellään aluksi tavallisimmat kehitysyhteistyön muodot, sekä esitellään talousteoreettisia näkökulmia kehitysyhteistyön tehokkuuden määrittelylle. Tutkielma perustuu puhtaasti teoreettisiin malleihin ja niissä sovelletut menetelmät ovat matemaattisia. Tutkielmassa käsitellään ensin tapaus, jossa kehitysyhteistyöllä rahoitetaan julkisen sektorin investointihankkeita. Jossain tapauksissa kehitysavun kasvu lasku siirtää vastaanottajamaan kulutusta julkisista investoinneista kulutukseen, jolloin kehitysyhteistyövaroin osittain rahoitettujen hankkeiden koko pienenee, ja suhteellinen tehokkuus laskee. Seuraavaksi tarkastellaan tilannetta, jossa kehitysyhteistyövaroista vain osa päätyy hankkeen rahoittamiseen, ja todetaan, että kehitysavun tehokkuus ja vaikutus maan kansantulon kasvuun vähenee talouden toimijoiden ylijäämää tavoittelevan käyttäytymisen (mukaan lukien korruptio) myötä entisestään. Tämän tutkimuksen perusteella voidaan todeta, että kehitysapu vaikuttaa kehittyvän maan talouden kasvuun tapauksessa, jossa julkisia infrastruktuurihankkeita rahoitetaan osittain maan omin verovaroin ja osittain kehitysyhteistyövaroin. Ylijäämää tavoitteleva käyttäytyminen vaikuttaa kehitysavun tehokkuuteen negatiivistesti vähentäen kehitysavun positiivisia kasvuvaikutuksia.