937 resultados para Variability of surface wind field
Resumo:
Purpose: The aim of this study was to evaluate the effect of two surface conditioning methods on the microtensile bond strength of a resin cement to three high-strength core ceramics: high alumina-based (In-Ceram Alumina, Procera AllCeram) and zirconia-reinforced alumina-based (In-Ceram Zirconia) ceramics. Materials and Methods: Ten blocks (5 ×6 × 8 mm) of In-Ceram Alumina (AL), In-Ceram Zirconia (ZR), and Procera (PR) ceramics were fabricated according to each manufacturer's instructions and duplicated in composite. The specimens were assigned to one of the two following treatment conditions: (1) airborne particle abrasion with 110-μm Al2O3 particles + silanization, (2) silica coating with 30 μm SiOx particles (CoJet, 3M ESPE) + silanization. Each ceramic block was duplicated in composite resin (W3D-Master, Wilcos, Petrópolis, RJ, Brazil) using a mold made out of silicon impression material. Composite resin layers were incrementally condensed into the mold to fill up the mold and each layer was light polymerized for 40 s. The composite blocks were bonded to the surface-conditioned ceramic blocks using a resin cement system (Panavia F, Kuraray, Okayama, Japan). One composite resin block was fabricated for each ceramic block. The ceramic-composite was stored at 37°C in distilled water for 7 days prior to bond tests. The blocks were cut under water cooling to produce bar specimens (n = 30) with a bonding area of approximately 0.6 mm2. The bond strength tests were performed in a universal testing machine (crosshead speed: 1 mm/min). Bond strength values were statistically analyzed using two-way ANOVA and Tukey's test (≤ 0.05). Results: Silica coating with silanization increased the bond strength significantly for all three high-strength ceramics (18.5 to 31.2 MPa) compared to that of airborne particle abrasion with 110-μm Al2O3 (12.7-17.3 MPa) (ANOVA, p < 0.05). PR exhibited the lowest bond strengths after both Al2O3 and silica coating (12.7 and 18.5 MPa, respectively). Conclusion: Conditioning the high-strength ceramic surfaces with silica coating and silanization provided higher bond strengths of the resin cement than with airborne particle abrasion with 110-μm Al2O3 and silanization.
Resumo:
OBJECTIVE: This study evaluated the efficiency of repolishing, sealing with surface sealant, and the joining of both in decreasing the surface roughness of resin-based composites after a toothbrushing process. METHOD AND MATERIALS: Ten specimens of each composite (Alert, Z100, Definite, and Prodigy Condensable), measuring 2 mm in thickness and 4 mm in diameter, were made and submitted to finishing and polishing processes on both sides of the specimens using the Sof-Lex system. The specimens were then subjected to toothbrushing (30,000 cycles), and surface roughness (Ra) was analyzed with a Surfcorder SE 1700 profilometer. The upper surface of each composite was etched with 37% phosphoric acid, and the surface-penetrating sealant Protect-it was applied on 1 surface. The roughness of these surfaces was again measured. On the other side, the surface of the specimen was repolished, and the efficiency of this procedure was measured using the profilometer. The surface roughness resulting from the joining of the 2 methods was verified by applying, in the final stage, the surface-penetrating sealant on the repolished surface. Data were analyzed with analysis of variance and Tukey test (P <.05). RESULTS: Results showed that the lowest surface roughness values were obtained for Definite, Z100, and Prodigy Condensable after the repolishing process and after the repolishing plus sealing. For Alert, the joining of repolishing plus sealing promoted the lowest values of surface roughness. CONCLUSION: Of the resin-based composites, Alert demonstrated the highest values of surface roughness in all the techniques tested.
Resumo:
Purpose: The purpose of this study was to verify the influence of surface sealants and dentin adhesive systems on the microleakage of composite restorations. Methods: Class V cavities were made on the buccal faces of 100 permanent third molars and restored with Z250. After 24 hours, they were submitted to polishing and finishing processes. The teeth were divided into groups according to the sealant agent: group 1 - Single Bond; group 2 - Opti Bond Solo Plus; group 3 - Fortify; group 4 - Fortify Plus; and group 5 - control without sealant. The analysis of immediate microleakage was performed in 10 restorations from each group, soon after the sealing. The other 10 specimens from each group were submitted to tooth-brushing and thermal cycles. The teeth were isolated and immersed in 2% methylene blue solution, washed in tap water, and sectioned in the buccolingual direction. The percentage of marginal leakage was calculated using an image analysis program, and results were submitted to analysis of variance and Tukey's test. Results: All the sealed groups demonstrated lower microleakage values compared to the control group. Group 3, sealed with Fortify, presented the lowest mean microleakage values. Conclusion: The application of surface sealants effectively decreased the microleakage in composite resin restorations.
Resumo:
Chemical analysis carried out in leaves of 18 specimens of Piper aduncum L. (Piperaceae) occurring at Ripasa Reserve, Araraquara, SP, Brazil indicated two distinct populations when investigated over a period of 14 months (January 2000 to February 2001) and then submitted to cluster analysis. The two groups were characterized by accumulation of prenylated benzoic acids, chromenes and dihydrochalcone, respectively. A total of seven compounds were identified by HPLC analysis and compared with standards including two prenylated benzoic acid [aduncumene (1) and 3-(3′-7′-dimethyl-2′-6′-octadienyl)- 4-methoxy-benzoic acid (5)], four chromenes [methyl 2,2-dimethyl-8-(3′- methyl-2′-butenyl)-2H-1-chromene-6-carboxylate (4), methyl 2,2-dimethyl-2H-1-chromene-6-carboxylate (2b), methyl 8-hydroxy-2,2-dimethyl-2H- 1-chromene-6-carboxylate (3) and 2,2-dimethyl-2H-1-chromene-6-carboxylic acid (2a)] and one dihydrochalcone [2′,6′-dihydroxy-4′-methoxy- dihydrochalcone (6)]. © 2009 Academic Journals.
Resumo:
The advancement of knowledge in neurophysiology has demonstrated that acupuncture is a method of peripheral neural stimulation that promotes local and systemic reflexive responses. The purpose of this study was to determine if surface electromyography can be used as a tool to study the action of auricular acupuncture on striated skeletal muscle. The electromyographic amplitudes of the anterior, middle and posterior deltoid muscle and the upper trapezium muscle with 20%, 40% and 60% of maximal voluntary contraction of 15 healthy volunteers, were analyzed after the individuals were submitted to the auricular acupuncture treatment. The non-parametric Friedman test was used to compare Root Mean Square values estimated by using a 200 ms moving window. Significant results were further analyzed using the Wilcoxon signed rank test. In this exploratory study, the level of significance of each comparison was set to p < 0.05. It was concluded in this study that a surface electromyography can be used as a tool to investigate possible alterations of electrical activity in muscles after auricular acupuncture. However there is still a lack of adequate methodology for its use in this type of study, being that the method used to record the electromyographic signal can also influence the results. © 2008 Elsevier Ltd. All rights reserved.
Resumo:
Investigation of the effectiveness of surface treatments that promote a strong bond strength of resin cements to metals can contribute significantly to the longevity of metal-ceramic restorations. This study evaluated the effect of surface treatments on the shear bond strength (SBS) of a resin cement to commercially pure titanium (CP Ti). Ninety cast CP Ti discs were divided into 3 groups (n=30), which received one of the following airborne-particle abrasion conditions: (1) 50 μm Al2O3 particles; (2) 30 μm silica-modified Al2O3 particles (Cojet Sand); (3) 110 μm silica-modified Al2O3 particles (Rocatec). For each airborne-particle abrasion condition, the following post-airborne-particle abrasion treatments were used (n=10): (1) none; (2) adhesive Adper Single Bond 2; (3) silane RelyX Ceramic Primer. RelyX ARC resin cement was bonded to CP Ti surfaces. All specimens were thermally cycled before being tested in shear mode. Failure mode was determined. The best association was Rocatec plus silane. All groups showed 100% adhesive failure. There were combinations that promote higher SBS than the protocol recommended by the manufacturer of RelyX ARC.
Resumo:
Includes bibliography
Resumo:
The CMS detector is designed around a large 4 T superconducting solenoid, enclosed in a 12 000-tonne steel return yoke. A detailed map of the magnetic field is required for the accurate simulation and reconstruction of physics events in the CMS detector, not only in the inner tracking region inside the solenoid but also in the large and complex structure of the steel yoke, which is instrumented with muon chambers. Using a large sample of cosmic muon events collected by CMS in 2008, the field in the steel of the barrel yoke has been determined with a precision of 3 to 8% depending on the location. © 2010 IOP Publishing Ltd and SISSA.
Resumo:
In addition to feeding on carrion tissues and fluids, social wasps can also prey on immature and adult carrion flies, thereby reducing their populations and retarding the decomposition process of carcasses. In this study, we report on the occurrence and behavior of social wasps attracted to vertebrate carrion. The collections were made monthly from September 2006 to October 2007 in three environments (rural, urban, and forest) in six municipalities of southeast Brazil, using baited bottle traps. We collected Agelaia pallipes (Olivier, 1791) (n = 143), Agelaia vicina (Saussure, 1854) (n = 106), Agelaia multipicta (Haliday, 1836) (n = 18), and Polybia paulista Ihering, 1896 (n = 3). The wasps were observed feeding directly on the baits and preying on adult insects collected in the traps. Bait and habitat associations, temporal variability of social wasps, and possible forensic implications of their actions are discussed. © 2011 Entomological Society of America.
Resumo:
This paper introduces a methodology for predicting the surface roughness of advanced ceramics using Adaptive Neuro-Fuzzy Inference System (ANFIS). To this end, a grinding machine was used, equipped with an acoustic emission sensor and a power transducer connected to the electric motor rotating the diamond grinding wheel. The alumina workpieces used in this work were pressed and sintered into rectangular bars. Acoustic emission and cutting power signals were collected during the tests and digitally processed to calculate the mean, standard deviation, and two other statistical data. These statistics, as well the root mean square of the acoustic emission and cutting power signals were used as input data for ANFIS. The output values of surface roughness (measured during the tests) were implemented for training and validation of the model. The results indicated that an ANFIS network is an excellent tool when applied to predict the surface roughness of ceramic workpieces in the grinding process.
Resumo:
The phenotypic characterization as well as the knowledge of the correlation among traits, is the first step to quantify the potential of a cross for further QTL (quantitative trait loci) detection. The present work aimed to evaluate the yield components and quality parameters variability of a mapping population derived from a bi-parental cross between IACSP95-3018 and IACSP93-3046 at plant cane and ratoon cane as well as to estimate the heritabilities and pair-wise correlation among the traits evaluated. The progeny clones differed significantly for the traits measures indicating the existence of significant amount of variability among them as also as the presence of transgressive clones. Broad-sense heritabilities values were generally high for stalk diameter, stalk weight, stalk height, Brix and Pol%Cane in plant cane and ratoon cane. Tones of sugarcane per hectare (TCH) were significantly correlated with stalk weight and stalk number in both years. Regarding to all the yield components, stalk number together with stalk weight were the most important components in the determination of TCH. While fiber and Pol%Cane were negative correlated showing that they are inversely correlated traits. © 2012 Society for Sugar Research & Promotion.
Resumo:
To properly describe the interactions between the ocean and atmosphere, it is necessary to assess a variety of time and spatial scales phenomena. Here, high resolution oceanographic and meteorological data collected during an observational campaign carried out aboard a ship in the tropical Atlantic Ocean, on May 15-24, 2002, is used to describe the radiation balance at the ocean interface. Data collected by two PIRATA buoys, along the equator at 23°W and 35°W and satellite and climate data are compared with the data obtained during the observational campaign. Comparison indicates remarkable similarity for daily and hourly values of radiation fluxes components as consequence of the temporal and spatial consistence presented by the air and water temperatures measured in situ and estimated from large scale information. The discrepancy, mainly in the Sao Pedro and Sao Paulo Archipelago area, seems to be associated to the local upwelling of cold water, which is not detected in all other estimates investigated here. More in situ data are necessary to clarify whether this upwelling flow has a larger scale effect and what are the meteorological and oceanographic implications of the local upwelling area on the tropical waters at the Brazilian coast.
Resumo:
Objectives: To evaluate the effects of surface treatment, surface hydration (SH) and application method (AM) on the tensile bond strength of the Silorane Adhesive System (SAS) to dentine. Methods: Ninety bovine teeth were used. For the control group (n = 10), each dentine surface was treated according to the manufacturer's instructions of the SAS. The remaining teeth were randomly distributed into two groups (n = 40), according to the type of dentine surface treatment (ST) - 37% phosphoric acid or Er:YAG Laser prior to the application of the SAS. Each group was further divided into 2 subgroups (n = 20), according to the SH status: dry (D) or wet (W). Each subgroup was further divided into 2 subgroups (n = 10), according to the application method [AM: Active (AC) mode or Passive (PA) mode]. A coat of resin composite (Filtek P90) was applied on the surface. Artificial ageing was performed with a thermo-mechanical cycling machine. The specimens were sectioned into 1 mm × 1 mm × 10 mm sticks and stressed to failure using a universal testing machine. The remaining teeth in each group were used for Scanning Electron Microscopy to examine the fractured area. Data were subjected to a three-way ANOVA, Tukey's test and Dunnet's test (α = 0.05). Results: The ANOVA showed significant differences for SH and AM, but not for ST. For SH, the results of Tukey's test were (in MPa): D-14.9(±3.8)a, W-17.1(±4.3)b; and for AM: PA-14. 9(±4.2)a, AC-17.1(±3.9) b. Conclusions: Acid etching, when combined with a moist dentine surface and the use of primer agitation, improves the bond strength of the SAS to dentine. Clinical Significance: According to the results of the present in vitro study, modification of the application protocols for the silorane-based adhesive system may improve its clinical performance. © 2012 Published by Elsevier Ltd.
Resumo:
In this paper we improve the regularity in time of the gradient of the pressure field in the solution of relaxed version of variational formulation proposed by V. I. Arnold and by Y. Brenier, for the incompressible Euler equations with variable density. We obtain that the pressure field is not only a measure, but a function in Lloc2((0,T);BVloc(D)) as an extension of the work of Ambrosio and Figalli (2008) in [1] to the variable density case. © 2013 Elsevier Ltd.
Resumo:
No ano de 2007, águas superficiais foram coletadas a partir de 21 pontos de amostragem na cidade de Barcarena, Região Norte, Brasil: um ponto de amostragem localizado em um pequeno córrego que recebe descarga de resíduos a partir da indústria de beneficiamento do caulim e deságua no Rio Curuperê, três pontos de amostragens localizados próximos de fontes que emergem na margem esquerda e deságuam no Rio Curuperê, nove pontos de amostragem no Rio Curuperê, que deságua no Rio Dendê, e oito no Rio Dendê, afluente da margem esquerda do Rio Pará. Para todas as amostras de água foram quantificadas 14 variáveis físico-químicas e níveis de 12 metais. Os resultados nos pontos próximos das fontes do Rio Curuperê apresentaram perfil físico-químico e níveis de metais típicos para águas superficiais e esses valores foram utilizados como referência para comparar e identificar possíveis alterações nas características químicas para os demais pontos de amostragem. Quando os resultados das fontes do rio Curuperê foram comparados com os resultados do ponto próximo a descarga de resíduos industriais foram observadas fortes alterações nos valores de 6 variáveis físico-químicas (pH, condutividade elétrica (EC), total de sólidos suspensos (TDS), nitrogênio amoniacal (N-NH4), sulfato (SO4) e salinidade) e aumento em magnitude dos níveis de quatro metais (Al, Fe, Mn e Zn), caracterizando que esses resíduos eram descarregados no ambiente sem tratamentos adequados. Os resultados nos demais pontos de amostragem demonstraram que estas condições anômalas também foram encontradas ao longo dos Rios Curuperê e Dendê, principalmente durante a maré baixa. A partir desta caracterização química das águas foram identificadas condições prejudiciais aos ecossistemas aquáticos e potencial risco à saúde da população local que usa os rios para consumo, recreação e transporte.