Análise de um queimador infravermelho funcionando com combustível híbrido : GLP/Bio-óleo

Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner

Gerenciamento de alarmes em plataformas marítimas de produção de hidrocarbonetos: metodologia e estudo de caso

In the operational context of industrial processes, alarm, by definition, is a warning to the operator that an action with limited time to run is required, while the event is a change of state information, which does not require action by the operator, therefore should not be advertised, and only stored for analysis of maintenance, incidents and used for signaling / monitoring (EEMUA, 2007). However, alarms and events are often confused and improperly configured similarly by developers of automation systems. This practice results in a high amount of pseudo-alarms during the operation of industrial processes. The high number of alarms is a major obstacle to improving operational efficiency, making it difficult to identify problems and increasing the time to respond to abnormalities. The main consequences of this scenario are the increased risk to personal safety, facilities, environment deterioration and loss of production. The aim of this paper is to present a philosophy for setting up a system of supervision and control, developed with the aim of reducing the amount of pseudo-alarms and increase reliability of the information that the system provides. A real case study was conducted in the automation system of the offshore production of hydrocarbons from Petrobras in Rio Grande do Norte, in order to validate the application of this new methodology. The work followed the premises of the tool presented in ISA SP18.2. 2009, called "life cycle alarm . After the implementation of methodology there was a significant reduction in the number of alarms

Novo método para estimativa do gradiente de fratura para poços de petróleo

The development of oil wells drilling requires additional cares mainly if the drilling is in offshore ultra deep water with low overburden pressure gradients which cause low fracture gradients and, consequently, difficult the well drilling by the reduction of the operational window. To minimize, in the well planning phases, the difficulties faced by the drilling in those sceneries, indirect models are used to estimate fracture gradient that foresees approximate values for leakoff tests. These models generate curves of geopressures that allow detailed analysis of the pressure behavior for the whole well. Most of these models are based on the Terzaghi equation, just differentiating in the determination of the values of rock tension coefficient. This work proposes an alternative method for prediction of fracture pressure gradient based on a geometric correlation that relates the pressure gradients proportionally for a given depth and extrapolates it for the whole well depth, meaning that theses parameters vary in a fixed proportion. The model is based on the application of analytical proportion segments corresponding to the differential pressure related to the rock tension. The study shows that the proposed analytical proportion segments reaches values of fracture gradient with good agreement with those available for leakoff tests in the field area. The obtained results were compared with twelve different indirect models for fracture pressure gradient prediction based on the compacting effect. For this, a software was developed using Matlab language. The comparison was also made varying the water depth from zero (onshore wellbores) to 1500 meters. The leakoff tests are also used to compare the different methods including the one proposed in this work. The presented work gives good results for error analysis compared to other methods and, due to its simplicity, justify its possible application

Metodologia para avaliação de cinemática de partículas gasosas em fluidos de viscosidade variável com o tempo e sua aplicação na construção de poços de petróleo

Many challenges have been presented in petroleum industry. One of them is the preventing of fluids influx during drilling and cementing. Gas migration can occur as result of pressure imbalance inside the well when well pressure becomes lower than gas zone pressure and in cementing operation this occurs during cement slurry transition period (solid to fluid). In this work it was developed a methodology to evaluate gas migration during drilling and cementing operations. It was considered gel strength concept and through experimental tests determined gas migration initial time. A mechanistic model was developed to obtain equation that evaluates bubble displacement through the fluid while it gels. Being a time-dependant behavior, dynamic rheological measurements were made to evaluate viscosity along the time. For drilling fluids analyzed it was verified that it is desirable fast and non-progressive gelation in order to reduce gas migration without affect operational window (difference between pore and fracture pressure). For cement slurries analyzed, the most appropriate is that remains fluid for more time below critical gel strength, maintaining hydrostatic pressure above gas zone pressure, and after that gels quickly, reducing gas migration. The model developed simulates previously operational conditions and allow changes in operational and fluids design to obtain a safer condition for well construction

Controle aplicado a poços com método de elevação e bombeio centrífugo submerso

The Electrical Submersible Pumping is an artificial lift method for oil wells employed in onshore and offshore areas. The economic revenue of the petroleum production in a well depends on the oil flow and the availability of lifting equipment. The fewer the failures, the lower the revenue shortfall and costs to repair it. The frequency with which failures occur depends on the operating conditions to which the pumps are submitted. In high-productivity offshore wells monitoring is done by operators with engineering support 24h/day, which is not economically viable for the land areas. In this context, the automation of onshore wells has clear economic advantages. This work proposes a system capable of automatically control the operation of electrical submersible pumps, installed in oil wells, by an adjustment at the electric motor rotation based on signals provided by sensors installed on the surface and subsurface, keeping the pump operating within the recommended range, closest to the well s potential. Techniques are developed to estimate unmeasured variables, enabling the automation of wells that do not have all the required sensors. The automatic adjustment, according to an algorithm that runs on a programmable logic controller maintains the flow and submergence within acceptable parameters avoiding undesirable operating conditions, as the gas interference and high engine temperature, without need to resort to stopping the engine, which would reduce the its useful life. The control strategy described, based on modeling of physical phenomena and operational experience reported in literature, is materialized in terms of a fuzzy controller based on rules, and all generated information can be accompanied by a supervisory system

Uma metodologia para a análise do desempenho sustentável dos postos de revenda de combustível na cidade de Natal/RN, com o uso de data envelopment analysis-DEA

The increasing use of fossil fuels in line with cities demographic explosion carries out to huge environmental impact in society. For mitigate these social impacts, regulatory requirements have positively influenced the environmental consciousness of society, as well as, the strategic behavior of businesses. Along with this environmental awareness, the regulatory organs have conquered and formulated new laws to control potentially polluting activities, mostly in the gas stations sector. Seeking for increasing market competitiveness, this sector needs to quickly respond to internal and external pressures, adapting to the new standards required in a strategic way to get the Green Badge . Gas stations have incorporated new strategies to attract and retain new customers whom present increasingly social demand. In the social dimension, these projects help the local economy by generating jobs and income distribution. In this survey, the present research aims to align the social, economic and environmental dimensions to set the sustainable performance indicators at Gas Stations sector in the city of Natal/RN. The Sustainable Balanced Scorecard (SBSC) framework was create with a set of indicators for mapping the production process of gas stations. This mapping aimed at identifying operational inefficiencies through multidimensional indicators. To carry out this research, was developed a system for evaluating the sustainability performance with application of Data Envelopment Analysis (DEA) through a quantitative method approach to detect system s efficiency level. In order to understand the systemic complexity, sub organizational processes were analyzed by the technique Network Data Envelopment Analysis (NDEA) figuring their micro activities to identify and diagnose the real causes of overall inefficiency. The sample size comprised 33 Gas stations and the conceptual model included 15 indicators distributed in the three dimensions of sustainability: social, environmental and economic. These three dimensions were measured by means of classical models DEA-CCR input oriented. To unify performance score of individual dimensions, was designed a unique grouping index based upon two means: arithmetic and weighted. After this, another analysis was performed to measure the four perspectives of SBSC: learning and growth, internal processes, customers, and financial, unifying, by averaging the performance scores. NDEA results showed that no company was assessed with excellence in sustainability performance. Some NDEA higher efficiency Gas Stations proved to be inefficient under certain perspectives of SBSC. In the sequence, a comparative sustainable performance and assessment analyzes among the gas station was done, enabling entrepreneurs evaluate their performance in the market competitors. Diagnoses were also obtained to support the decision making of entrepreneurs in improving the management of organizational resources and promote guidelines the regulators. Finally, the average index of sustainable performance was 69.42%, representing the efforts of the environmental suitability of the Gas station. This results point out a significant awareness of this segment, but it still needs further action to enhance sustainability in the long term

Aspectos econômicos da produção de bovinos de corte

O Brasil ocupa as posições de maior produtor e exportador mundial de carne bovina, com a região Centro-Oeste respondendo por 35% do abate nacional, em 2010. Entretanto, faz-se necessário valorizar o planejamento, o controle e a gestão empresarial nas propriedades produtoras, visando ao lucro na atividade. O presente estudo objetivou analisar e avaliar a viabilidade econômica da produção de bovinos de corte, em Camapuã (MS), a fim de identificar os itens relevantes aos custos da atividade. Como direcionador dos custos variáveis, no custo operacional efetivo, o suplemento mineral fornecido aos animais e a mão de obra mostraram-se relevantes para a gestão do sistema de produção, representando, aproximadamente, 71% dos custos. Com base nos resultados apresentados, pôde-se concluir que a propriedade apresenta boa lucratividade (superior a 20%). Verificou-se, ainda, com base no fluxo de caixa, taxa interna de retorno de 13,13% e capital inicial investido retornando em, aproximadamente, 7 anos, com resultados atrativos para o investimento, neste segmento agropecuário. O estudo proporcionou um parâmetro de custo para o produtor pecuarista, podendo contribuir para um melhor planejamento de atividades, em que, apesar dos altos investimentos iniciais, possivelmente, poderá reduzir seus custos, com o manejo racional no sistema produtivo, o que seria mais atrativo para o mercado, tornando mais viáveis as suas atividades de produção e comercialização do produto.

Pesquisa odontológica no Brasil: características da produção científica no início do século XXI

Dentistry, as a science and field of knowledge, has presented a substantial development in the last decades in the areas of research and education. The aim of this study was to evaluate the Brazilian scientific production in Dentistry, as from their methodological outlining, which characterizes the XXI Century. Five thousand two hundred and three study abstracts were evaluated, comprising works presented in the meetings of the Brazilian Society of Dentistry Research (SBPqO), during the period of 2001 to 2006. The main results identify that, as for the methodology used in the researches, there was a predominance of the studies of an individuate, interventionist and longitudinal nature; of the researches in the areas of Dentistry, Periodontology, Endodontics, Pedodontics and Collective Oral Health and experimental studies about clinical researches or with collective subjects. The inter and multidisciplinarity are pointed out in the outlining of this study, as the triad Education-Health-Research is discussed, so that they transcend in their fields of action, in the direction of the transdisciplinarity. It is concluded that, in the studied period, there was a reasonable and balanced production in Brazilian dental field

Large scale laboratory cultures of Ankistrodesmus gracilis (Reisch) Korsikov (Chlorophyta) and Diaphanosoma biergei Korinek, 1981 (Cladocera)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Projeto Prevenir: uma pesquisa acerca das mudanças no perfil das infecções por DST/AIDS, com a perspectiva de detectar pontos vulneráveis da prevenção

Rio Grande do Norte is among the Brazilian States where the tourism and sexual violence increasingly grow in the country, occupying 4th place in 2004. Associated to this fact, it comes the problematic one of the contamination of the women by Sexually Transmitted Disease (STD). Studies in Brazil have presented a considerable increase of the STDs, caused through lack of suitable protection in the sexual relationships. Due to the biological and psychosocial vulnerability, besides failures or inconsistencies in the condom use associated to the raised taxes of sexual activity with different partners, the STDs constitute the main risk of health. Many difficulties are found by the confrontation of this problem. In this context, this project had as aim to evaluate the vulnerability of this population of sexually active women in Natal-RN Ponta Negra neighbourhood to the infections by STDs, such as, Candida sp., Vaginoses Bacterial, Trichomonas Vaginalis and Chlamydia sp., arisen with the explosion of the sex market, showing a current statistical panorama. It was possible to detect vulnerable points in prevention through patient anamnesis, where the study it showed: high number of partners (8,3% with more than five), low age of first relationship and not the use of condoms (31,8% sometimes use and 45,8% had not used in the first relationship). Already consolidated by the preventive cytopathologic examination, these data were strengthened by high incidence of causing agents of STDs (58,6%). In this way, it is clear that the sexuality must to be thought on the context of the deep economic and socio-cultural transformations in which pass societies, and mainly the ones concerning to the sexuality exercise and to the sex market. With the profile change of the infections, new demands are placed in relation to the risk factors. Therefore, it can be concluded that the prevention vulnerable points detected as more important had been the deficiency in self-perception and wareness of the risk existence among the studied women

Desempenho operacional de um protótipo “aerossolo”

It is been a great deal of interest the studying of the operational performance of tractors and its machinery especially in work conditions. The present study had as objective to evaluate the operational performance of an Aerossolo prototype tracked with a Valtra BM100 4x2 TDA, with the engine power of 73.6 kW (100 cv). The prototype equipment is a drag type, hydraulically commanded, with telescopic heading for longitudinal adjustment, two lateral sections with 28 knifes in each one of them, concrete ballasts, wheels of transport and aggregate breaker coil. The work was conducted in the Department of Agricultural Engineering of the UNESP, Jaboticabal Campus, in a randomized blocks design, factorial 3 x 3, with four repetitions. The nine studied treatments were a combination for three ballast conditions (0; 960 and 1,307 kg) and three angles of the sections (0 degrees; 7 degrees and 14 degrees). The results indicate an increase in operational consumption (liters per hectare) of 32.4% in relation to the concrete ballast addition, and a 26.8% in relation to the angle variation between sections. The working depth, traction force and power demands were higher with the increases in the concrete ballast and the angle variation between sections.

Operational parameters of soybean seeding in santa fe system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Qualidade microbiológica de leite UHT caprino: pesquisa de bactérias dos gêneros Staphylococcus, Bacillus e Clostridium

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Pesquisa de anticorpos anti-Neospora caninum em bovinos leiteiros, cães e trabalhadores rurais da região Sudoeste do Estado de Mato Grosso

Considerando a importância da neosporose interferindo na produtividade animal, avaliou-se a frequência de anticorpos anti-Neospora caninum em amostras de soros de bovinos leiteiros da Região Sudoeste do Estado de Mato Grosso, Brasil, complementando-se com amostras sorológicas colhidas de cães e de humanos que conviviam nas mesmas propriedades rurais amostradas. Um total de 1.036 amostras de soros foram analisadas, sendo 932 de fêmeas bovinas leiteiras, 37 de cães e 67 de humanos, provenientes de 24 propriedades e examinados por meio da reação de imunofluorescência indireta (RIFI). As amostras de soros humanos reagentes foram testadas novamente por Western-blotting para confirmação dos resultados. Anticorpos anti-N. caninum foram encontrados em 499 bovinos (53,5%), em pelo menos um animal positivo por propriedade, em 25 caninos (67,6%) e em sete humanos (10,5%). Não houve diferença significativa no número de bovinos positivos por faixa etária. Os resultados obtidos indicam uma ampla disseminação de N. caninum na região estudada.

O desafio da parceria na implementação do PRONERA: o caso do projeto alfabetização cidadã no nordeste Paraense.

El desafío de la parcería en la implantación del PRONERA: el caso del Proyecto Alfabetización Ciudadana en Noreste de Pará se constituye en un estudio sobre las políticas públicas de educación del campo. El trabajo tiene como objeto de análisis la implantación del PRONERA, a partir del estudio de caso del Proyecto de Alfabetización Ciudadana en Noreste de Pará, con el objetivo de comprender como la parcería, principio operacional y metodológico propuesto por el PRONERA, se concretó en la implantación del Proyecto y cuales sus posibles implicaciones en las políticas públicas de educación del campo. Entre los procedimientos metodológicos, realizamos la investigación bibliográfica y documental que nos permitieron situar la educación del campo en términos históricos y políticos, sistematizar la constitución y la organización del PRONERA y reflexionar acerca de la parcería a partir de diferentes ópticas. Realizamos también la investigación de campo por medio de entrevistas semi-estructuradas, con el propósito de analizar la implantación del Proyecto da Alfabetización Ciudadana, a partir del dialogo con los actores sociales involucrados. Los resultados de las análisis indicaron que, históricamente, las políticas públicas de educación destinadas a las poblaciones de la zona rural fueron instituidas verticalmente, desvinculadas de la realidad del campo e incompatibles con las necesidades e intereses de los sujetos. Constatamos que, en período reciente, movimientos sociales del campo reivindican y proponen acciones que se establezcan como políticas públicas de educación del campo. Identificamos que el PRONERA resulta de ese movimiento y se presenta como anuncio de una política pública de educación del campo, teniendo como diferencial el hecho de ser un programa del gobierno federal idealizado fuera de la esfera gubernamental, construido por los movimientos sociales del campo y presentar, entre otras innovaciones, el modelo de parcería y la gestión compartida, participativa y democrática. En esta perspectiva, en este estudio de caso, se evidenció que la parcería, frente a los conflictos y las disputas entre sus miembros participantes, no es el problema de la implantación del PRONERA, sino su punto fuerte. De este modo, la parcería es uno de los elementos necesarios para la construcción de políticas públicas, en particular, de educación del campo, una vez que posibilita la interacción de instituciones públicas y movimientos sociales locales, atribuyendo legitimidad a la educación del campo. Al promover un proceso de aprendizaje democrático, la parcería se presenta como estrategia de democratización de la educación del campo.