Performance of the CMS cathode strip chambers with cosmic rays

The Cathode Strip Chambers (CSCs) constitute the primary muon tracking device in the CMS endcaps. Their performance has been evaluated using data taken during a cosmic ray run in fall 2008. Measured noise levels are low, with the number of noisy channels well below 1%. Coordinate resolution was measured for all types of chambers, and fall in the range 47μm to 243μm. The efficiencies for local charged track triggers, for hit and for segments reconstruction were measured, and are above 99%. The timing resolution per layer is approximately 5 ns. © 2010 IOP Publishing Ltd and SISSA.

Performance of CMS muon reconstruction in cosmic-ray events

The performance of muon reconstruction in CMS is evaluated using a large data sample of cosmic-ray muons recorded in 2008. Efficiencies of various high-level trigger, identification, and reconstruction algorithms have been measured for a broad range of muon momenta, and were found to be in good agreement with expectations from Monte Carlo simulation. The relative momentum resolution for muons crossing the barrel part of the detector is better than 1% at 10 GeV/c and is about 8% at 500 GeV/c, the latter being only a factor of two worse than expected with ideal alignment conditions. Muon charge misassignment ranges from less than 0.01% at 10GeV/c to about 1% at 500 GeV/c. © 2010 IOP Publishing Ltd and SISSA.

Cutting performance of diamond coated Si3N4 tool during turning

Silicon nitride cutting tools have been used successfully for machining hard materials, like: cast irons, nickel based alloys, etc. However these cutting tools with diamond coating present little information on dry turning operations of gray cast iron. In the present work, Si3N4 square inserts was developed, characterized and subsequently coated with diamond for dry machining operations on gray cast iron. All experiments were conducted with replica. It was used a 1500, 3000, 4500 m cutting length, feed rate of 0.33 mm/rev and keeping the depth of cut constant and equal to 1 mm. The results show that wear in the tool tips of the Si3N4 inserts, in all cutting conditions, was caused by both mechanical and chemical processes. To understand the tool wear mechanisms, a morphological analysis of the inserts, after experiments, has been performed by SEM and optical microscopy. Diamond coated PVD inserts showed to be capable to reach large cutting lengths when machining gray cast iron. © (2010) Trans Tech Publications.

Performance of cultivars of crisp mini-lettuce with respect to ground cover and spacing, in three planting times

The planting of lettuce in greenhouses, as well as covering beds with a polyethylene sheet, is a viable technology, promoting improvements in microclimatic conditions of the environment. In view of the little information on mini-lettuce, the aim of this work was to evaluate the performance of three cultivars of crisp minilettuce ('Green Frizzly', 'Red Frizzly no. 1' and 'Red Frizzly no. 2') with and without ground cover, under different spacings (20 × 15 cm and 20 × 20 cm), in three planting times (1: November 16, 2004; 2: December 17, 2004; and 3: January 20, 2005). The study was conducted in a greenhouse at UNESP-FCAV, Jaboticabal-SP. The experiments were carried out using a randomized block design, following a 3 × 2 × 2 factorial scheme with 12 treatments and three repetitions. The characteristics evaluated were plant height (cm), head diameter (cm), fresh weight (g) and number of leaves per plant. Planting time 3 was shown to be favorable for all the characteristics analyzed. 'Red Frizzly no. 2' was found to be the most suited to planting time 1, and for planting times 2 and 3, this cultivar did not differ from 'Red Frizzly no. 1'. The factor ground cover was not found to affect the characteristics evaluated, and therefore, cultivation without ground cover is recommended. The spacing 20 × 15 cm was shown to be favorable, resulting in cultivation with the highest populations, thereby increasing productivity. Based on the results obtained and for the conditions in which the experiment was conducted, it can be concluded that: planting time 3 (January 20, 2005) was the most favorable; the cultivars 'Red Frizzly no. 2' and 'Red Frizzly no. 1' are adapted to all the planting times; and cultivation without ground cover using a spacing of 20 × 15 cm was the most suitable.

Performance of CMS muon reconstruction in pp collision events at √s = 7TeV

The performance of muon reconstruction, identification, and triggering in CMS has been studied using 40 pb-1 of data collected in pp collisions at s = 7 TeV at the LHC in 2010. A few benchmark sets of selection criteria covering a wide range of physics analysis needs have been examined. For all considered selections, the efficiency to reconstruct and identify a muon with a transverse momentum pT larger than a few GeV/c is above 95% over the whole region of pseudorapidity covered by the CMS muon system, < 2.4, while the probability to misidentify a hadron as a muon is well below 1%. The efficiency to trigger on single muons with pT above a few GeVc is higher than 90% over the full η range, and typically substantially better. The overall momentum scale is measured to a precision of 0.2% with muons from Z decays. The transverse momentum resolution varies from 1% to 6% depending on pseudorapidity for muons with pT below 100GeV/c and, using cosmic rays, it is shown to be better than 10% in the central region up to pT = 1 TeV/c. Observed distributions of all quantities are well reproduced by the Monte Carlo simulation. © 2012 IOP Publishing Ltd and Sissa Medialab srl.

Evaluation of low-level laser therapy effectiveness on the pain and masticatory performance of patients with myofascial pain

This study investigated the effect of low-level laser therapy (LLLT) on the masticatory performance (MP), pressure pain threshold (PPT), and pain intensity in patients with myofascial pain. Twenty-one subjects, with myofascial pain according to Research Diagnostic Criteria/temporomandibular dysfunction, were divided into laser group (n = 12) and placebo group (n = 9) to receive laser therapy (active or placebo) two times per week for 4 weeks. The measured variables were: (1) MP by analysis of the geometric mean diameter (GMD) of the chewed particles using Optocal test material, (2) PPT by a pressure algometer, and (3) pain intensity by the visual analog scale (VAS). Measurements of MP and PPT were obtained at three time points: baseline, at the end of treatment with low-level laser and 30 days after (follow-up). VAS was measured at the same times as above and weekly throughout the laser therapy. The Friedman test was used at a significance level of 5 % for data analysis. The study was approved by the Ethics Committee of the Federal University of Sergipe (CAAE: 0025.0.107.000-10). A reduction in the GMD of crushed particles (p < 0.01) and an increase in PPT (p < 0.05) were seen only in the laser group when comparing the baseline and end-of-treatment values. Both groups showed a decrease in pain intensity at the end of treatment. LLLT promoted an improvement in MP and PPT of the masticatory muscles. © 2012 Springer-Verlag London.

Performance of children with learning difficulties in fine motor function and handwriting

This study aimed to compare and characterize the fine, sensory and perceptive function performance and handwriting quality between students with learning difficulties and students with good academic performance. Methods: This study comprised 192 students from 2nd to 4th grades, both genders, whose ages ranged from 7 to 11 years old. The students were distributed into: GI, GII, GIII and GIV, comprising 96 students with learning difficulties, and groups GV, GVI, GVII, GVIII comprising 96 students with good academic performance. The students were submitted to evaluation of fine motor, sensorial and perception functions and handwriting evaluation under dictation. Results: The results showed that the students with learning difficulties, from 1st to 3rd grade, had lower performance on tests of fine motor, sensory and perceptive function, when compared to the students with good academic performance in the same grade; the students from 4th grade, both groups, did not show changes on fine motor, sensory and perceptive function; and only the students of GII showed dysgraphia. Conclusions: the results presented in this study suggest that the qualitative aspects of fine motor, sensory and perceptive skills reflect the integrity and maturity of central nervous system and can probably play an important role in early diagnosis of development disorders and consequently prevent academic disorders such as handwriting performance.

Effects of vaccination against reproductive diseases on reproductive performance of beef cows submitted to fixed-timed AI in Brazilian cow-calf operations

The objectives were to assess incidence of pregnancy losses, associate this outcome with immunization programs against reproductive diseases, and evaluate the effects of vaccination against bovine herpesvirus-1 (BoHV-1), bovine viral diarrhea virus (BVDV), and Leptospira spp., on reproductive efficiency of Brazilian cow-calf operations. In experiment 1, 7614 lactating Nelore cows from 18 ranches were assigned to the same estrus synchronization and fixed-time AI protocol (ESFTAI; Days -11 to 0). Pregnancy status was determined with transrectal ultrasonography on Days 30 and 120 after AI. Pregnancy loss was deemed to have occurred when cows were pregnant on Day 30 but nonpregnant on Day 120. Incidence of pregnancy loss across all ranches was 4.1%; pregnancy losses were detected (P < 0.10) in 14 ranches but not detected (P > 0.11) in four ranches. Pregnancy loss was lower (P ≤ 0.02) in ranches that vaccinated against BoHV-1, BVDV, and Leptospira spp. compared with ranches that did not vaccinate, or only vaccinated against Leptospira spp. In experiments 2 and 3, lactating Nelore cows (N = 1950 and 2793, respectively) from ranches that did not have a history of vaccinating against reproductive diseases (experiment 2), or only vaccinated against Leptospira spp. (experiment 3), were assigned to the same ESFTAI used in experiment 1. Within each ranch, cows received (VAC) or not (CON) vaccination against BoHV-1, BVDV, and Leptospira spp. at the beginning of the ESFTAI (Day -11) and 30 days after (Day 41) AI. In experiment 2, VAC cows had greater (P ≤ 0.05) pregnancy rates compared with CON on Days 30 and 120. In experiments 2 and 3, pregnancy loss was reduced (P ≤ 0.03) in primiparous VAC cows compared with CON cohorts. In experiment 4, 367 primiparous, lactating Nelore cows previously vaccinated against Leptospira spp. were assigned to the same ESFTAI used in experiment 1. Cows received VAC, or the same vaccine 30 days before (Day -41) and at the beginning (Day -11) of the ESFTAI (PREVAC). Pregnancy rates on Days 30 and 120 were greater (P ≤ 0.05) in PREVAC cows compared with VAC cows. In conclusion, pregnancy losses affected reproductive and overall efficiency of Brazilian cow-calf operations, and might be directly associated with BoHV-1, BVDV, and Leptospira spp. infections. Hence, vaccinating cows against these pathogens, particularly when both doses are administered before fixed-time AI, improved reproductive performance in Brazilian cow-calf systems. © 2013 Elsevier Inc.

The export performance of Chilean firms: some stylized facts

Includes bibliography

Globalization and regional development: the economic performance of Chile's regions, 1990-2002

Includes bibliography

The performance of Chinese and Brazilian exports to Latin America, 1994-2009

Includes bibliography

Effects of dentin dry/moist condition on the immediate adhesive performance of different solvent-based etch-and-rinse adhesivesystems

Purpose: The purpose of this research was to analyze and measure, under optical microscopy, the hybrid layer thickness and resin tags length, as well as the microtensile bond strength of two conventional adhesive systems when applied to dry and moist dentinal substrate. Methods: Thirty-two extracted human molars were randomly distributed into four groups according to the adhesive systems (XP Bond and Prime&Bond 2.1) and moisture condition (dry and moist). In Groups I and II, XP adhesive system was applied on dry and moist dentin, respectively; while Groups III and IV received PB adhesive system, in the same way as was done in Groups I and II, respectively. After adhesive and restorative procedures, all specimens were sectioned along their long axes; one hemi-tooth sample was subjected to the microtensile bond strength test while the other was decalcified and serially sectioned into six micron thick slices and sequentially mounted on glass slides. These sections were stained by the Brown and Brenn method for posterior analysis and measurement of the hybrid layer and resin tags under a light microscope with a micrometric ocular 40/075. Results: Data were analyzed using two-way ANOVA and Tukey's test (α=0.05). For the variable hybrid layer thickness, XP showed no significant differences between dry and moist dentin (5.2 μm and 5.5 μm, respectively), but for PB, hybrid layer was significantly thicker for moist (4.0 μm) than for dry dentin (3.0 μm). For the variable resin tags length XP showed 17.9 μm length for dry dentin and 20.8 μm for moist dentin; PB 11.7 μm for dry and 12.69 μm for moist dentin;there was no significant differences between them, independent of the moisture condition. For the variable microtensile bond strength, XP showed 38.0 MPa for dry dentin and 44.5 MPa for moist dentin; and PB showed 22.7 MPa for dry dentin and 20.8 MPa for dry dentin no significant difference was observed between moist and dry dentin for XP (p=0.2) and PB (p=0.7), but XP was presented significantly higher bond strength values than PB in both moisture conditions (p=0.003 for dry and p=0.002 for moist). Conclusion: The two-step butanol-based etch-and-rinse adhesive XP Bond presented a superior behavior with regard to the hybrid layer thickness, length of resin tags and bond strength to dry and moist dentin substrates when compared with two-step acetone-based adhesive system Prime&Bond2.1. © 2013 Elsevier Ltd.

Effects of vaccination against reproductive diseases on reproductive performance of lactating dairy cows submitted to AI

Four experiments evaluated the effects of vaccination against bovine herpesvirus-1 (BoHV-1), bovine viral diarrhea virus (BVDV), and Leptospira spp. on reproductive performance of lactating dairy cows without (experiments 1, 2, and 3) or with previous vaccination against these diseases (experiment 4). Cows were assigned to a fixed-time AI protocol (FTAI; d -11 to 0) in all experiments, as well as AI 12. h upon estrus detection in experiment 3. Pregnancy status was determined with transrectal ultrasonography on d 30 and 71 (d 60 for experiment 3) after AI. Pregnancy loss was considered in cows pregnant on d 30 but non-pregnant on the subsequent evaluation. In experiment 1, 853 cows received (VAC) or not (CON) vaccination against BoHV-1, BVDV, and Leptospira spp. at the beginning of the FTAI (d -11) and 30. d after AI. Pregnancy loss was reduced (P=0.03) in VAC cows compared with CON. In experiment 2, 287 cows received VAC or CON 30. d prior to (d -41) and at the beginning (d -11) of the FTAI. Pregnancy rates on d 30 and 71 were greater (P≤0.03) in VAC cows compared with CON. In experiment 3, 1680 cows with more than 28. d in milk were randomly assigned to receive VAC or CON with doses administered 14. d apart, and inseminated within 15-135. d after the second dose. Pregnancy rates on d 30 and 60 were greater (P≤0.02) in VAC cows compared with CON. In experiment 4, 820 cows received (REVAC) or not (CON) revaccination against BoHV-1, BVDV, and Leptospira spp. at the beginning of the FTAI protocol (d -11). Pregnancy rates and loss were similar (P≥0.54) between treatments. Hence, vaccinating naïve cows against BoHV-1, BVDV, and Leptospira spp. improved reproductive efficiency in dairy production systems, particularly when both doses were administered prior to AI. © 2013 Elsevier B.V.

Effects of resistance training on the performance of activities of daily living in patients with Alzheimer's disease

Aim: The objective of this study was to investigate the effects of resistance training in activities of daily living performance in Alzheimer's disease (AD) patients. Methods: An exploratory and longitudinal study, lasting for 16weeks, with the participation of 34 patients divided equally in: the training group (TG), who participated in a resistance training protocol (three sets of 20 repetitions in five exercises); and the social gathering group (SGG), who participated in a social interaction protocol (i.e. group dynamics, writing and reading activities). Results: We observed significant differences between the groups in moving around the house, climbing stairs, standing up from the floor and putting on socks tests. Conclusion: This study showed that resistance training improves agility, lower limb strength, balance and flexibility in AD patients, while SGG protocol is important to improve the agility. © 2012 Japan Geriatrics Society.

The role of hierarchical morphologies in the superior gas sensing performance of CuO-based chemiresistors

The development of gas sensors with innovative designs and advanced functional materials has attracted considerable scientific interest given their potential for addressing important technological challenges. This work presents new insight towards the development of high-performance p-type semiconductor gas sensors. Gas sensor test devices, based on copper (II) oxide (CuO) with innovative and unique designs (urchin-like, fiber-like, and nanorods), are prepared by a microwave-assisted synthesis method. The crystalline composition, surface area, porosity, and morphological characteristics are studied by X-ray powder diffraction, nitrogen adsorption isotherms, field-emission scanning electron microscopy and high-resolution transmission electron microscopy. Gas sensor measurements, performed simultaneously on multiple samples, show that morphology can have a substantial influence on gas sensor performance. An assembly of urchin-like structures is found to be most effective for hydrogen detection in the range of parts-per-million at 200 °C with 300-fold larger response than the previously best reported values for semiconducting CuO hydrogen gas sensors. These results show that morphology plays an important role in the gas sensing performance of CuO and can be effectively applied in the further development of gas sensors based on p-type semiconductors. High-performance gas sensors based on CuO hierarchical morphologies with in situ gas sensor comparison are reported. Urchin-like morphologies with high hydrogen sensitivity and selectivity that show chemical and thermal stability and low temperature operation are analyzed. The role of morphological influences in p-type gas sensor materials is discussed. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.