Coastal engineering investigation at Jupiter Inlet, Florida

A fixed-bed hydraulic model of Jupiter Inlet, Florida, was constructed for the purpose of testing measures designed to remedy problems of sediment erosion and deposition in the inlet area. Both tide-induced flows as well as waves were simulated in the model which was built on an undistorted scale of 1:49. Model verification was based on prototype measurements of waves, tides and currents. Results have been interpreted in terms of the influence of various proposed remedial schemes on flow velocity magnitude, distribution and wave height at various locations within the study area. A stability parameter has been utilized for evaluating the degree of sediment erosion or deposition at a given location. Various structural solutions were examined in the model. It is proposed that, in the initial phase of solution implementation, sediment removal/nourishment methods be used primarily to mitigate the existing problems. New structures, as per model test results, should be installed under subsequent phases, only if sediment management procedures do not prove to be adequate. The currently followed procedure of periodic sand trap dredging may be extended to include the new dredging/nourishment requirements. (PDF contains 245 pages.)

Interim report on geology and ground-water resources of Indian River County, Florida

In the area of this investigation a partial inventory was made of the estimated 2,000 existing wells to obtain information on location, depth, and yield of representative wells. Also, data were obtained on the quality of water from the various aquifers, and on the fluctuation of water levels in certain wells in the Floridan aquifer. The hydraulic characteristics of the Floridan aquifer at several sites were determined by means of pumping tests. (PDF has 80 pages.)

Applying the Electrochemical Deposition Technology to Construct the Hybrid Devices

Nanowires functionalized by special molecules can be used to as the candidates for biological application in many areas. In this paper, nickel nanowires, which were fabricated by electrochemical deposition and functionalized by biotinylated peptide, were applied to constructing the hybrid device powered by F-1-ATPase motors.

Modeling the Chesapeake Bay and Tributaries: a synopsis

The last decade has seen the development and application of a spectrum of physical and numerical hydrographic models of the Chesapeake Bay and its tributaries. The success of the James River Hydraulic Model has initiated the construction of an estuarine hydraulic model of the entire Chesapeake System. Numerical analogues for hydrographic behavior and contaminant dispersion in one-, two-, and three dimensional model estuaries exist for various regions of the Bay. From an engineering viewpoint, one dimensional models are sufficiently advanced to be routinely employed in aiding management decisions. Bay investigators are playing leading roles in the development of two- and three-dimensional models of estuarine flows.

Characteristics of Wake Flow in Long Bluff Bodies

Vortex shedding is the main characteristics of bluff bodies, which will cause the bluff bodies to vibrate and sometimes result in the structures failure. In this paper the wake flow characteristics of 21 bluff bodies with rectangular, rounded and angular profiles and the length-to-width ratio in the range of 4~12 were deeply studied by Micro ADV. Two parameters, namely the relative intensity of the load due to Karman vortices and the large scale vortex intensity, were introduced to measure the wake flow intensity. Generally, the values of these parameters for different bluff bodies are consistent with each other. The experiment results showed that the key factor affecting the wake flow characteristics is the bluff edge, especially the leading edge geometry. The wake flow in bluff bodies with rounded edge profiles has more regular vortices and becomes more periodic than that in bluff bodies with rectangular ones. A bluff body with angular edged profile was witnessed to have not only small wake loading but small hydraulic resistance also.

Effects of rainfall infiltration on the stability of soil slopes

Slope failure due to rainfall is a common geotechnical problem. The mechanics of rainfall induced landslides involves the interaction of a number of complex hydrologic and geotechnical factors. This study attempts to identify the influence of some of these factors on the stability of soil slope including rainfall intensity, hydraulic conductivity and the strength parameters of soil.

Respuesta a la sequía de Pinus radiata D. Don y su implicación en los procesos de tolerancia

160 p. (Bibliogr. 141-160)

Effective and Robust Generalized Predictive Speed Control of Induction Motor

14 p.

A robust position control for induction machines

ICEM 2010

Potentials for fisheries in the Niger Delta: Another green light for self sufficiency in regional food production

A discussion is presented on the potential for fishery development in the Niger Delta region, considering engineering activities and food production potentials of the freshwater zone and immediate hinterland, the brackishwater mangrove swamps and the estuaries. An examination of current trends in the environment indicates that a possible solution to improved exploitation of the region lies in hydraulic engineering, the manipulation of environmental conditions through varying freshwater and seawater inputs so as to increase aquatic and wetland productivity

Kontrol esparruan ikasketa eta garapenerako oinarrizko ingurune praktiko, ireki eta askea

Embedded system design (VHDL description) based on Xilinx's Spartan3E Development Kit to perform real-time PID control and monitoring of DC motors.

Digested sludge: delineation and modeling for ocean disposal

Experimental work was performed to delineate the system of digested sludge particles and associated trace metals and also to measure the interactions of sludge with seawater. Particle-size and particle number distributions were measured with a Coulter Counter. Number counts in excess of 10¹² particles per liter were found in both the City of Los Angeles Hyperion mesophilic digested sludge and the Los Angeles County Sanitation Districts (LACSD) digested primary sludge. More than 90 percent of the particles had diameters less than 10 microns.

Total and dissolved trace metals (Ag, Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) were measured in LACSD sludge. Manganese was the only metal whose dissolved fraction exceeded one percent of the total metal. Sedimentation experiments for several dilutions of LACSD sludge in seawater showed that the sedimentation velocities of the sludge particles decreased as the dilution factor increased. A tenfold increase in dilution shifted the sedimentation velocity distribution by an order of magnitude. Chromium, Cu, Fe, Ni, Pb, and Zn were also followed during sedimentation. To a first approximation these metals behaved like the particles.

Solids and selected trace metals (Cr, Cu, Fe, Ni, Pb, and Zn) were monitored in oxic mixtures of both Hyperion and LACSD sludges for periods of 10 to 28 days. Less than 10 percent of the filterable solids dissolved or were oxidized. Only Ni was mobilized away from the particles. The majority of the mobilization was complete in less than one day.

The experimental data of this work were combined with oceanographic, biological, and geochemical information to propose and model the discharge of digested sludge to the San Pedro and Santa Monica Basins. A hydraulic computer simulation for a round buoyant jet in a density stratified medium showed that discharges of sludge effluent mixture at depths of 730 m would rise no more than 120 m. Initial jet mixing provided dilution estimates of 450 to 2600. Sedimentation analyses indicated that the solids would reach the sediments within 10 km of the point discharge.

Mass balances on the oxidizable chemical constituents in sludge indicated that the nearly anoxic waters of the basins would become wholly anoxic as a result of proposed discharges. From chemical-equilibrium computer modeling of the sludge digester and dilutions of sludge in anoxic seawater, it was predicted that the chemistry of all trace metals except Cr and Mn will be controlled by the precipitation of metal sulfide solids. This metal speciation held for dilutions up to 3000.

The net environmental impacts of this scheme should be salutary. The trace metals in the sludge should be immobilized in the anaerobic bottom sediments of the basins. Apparently no lifeforms higher than bacteria are there to be disrupted. The proposed deep-water discharges would remove the need for potentially expensive and energy-intensive land disposal alternatives and would end the discharge to the highly productive water near the ocean surface.

Diseño y verificación del sistema de interpolación de trayectorias de un mecanismo de cinemática paralela

[ES]El objetivo principal del presente Trabajo Fin de Grado es diseñar un interpolador de trayectorias y programarlo en Labview. Para ello, se ha de analizar primeramente la cinemática del mecanismo a utilizar, un robot de cinemática paralela 5R, y calcular su espacio de trabajo. Después, se deducirán y programarán diversos perfiles de velocidades (trapezoidal de velocidades, trapezoidal de aceleraciones y sinusoidal) para moverse en rectas, así como el movimiento en curvas mediante splines. También se hallarán experimentalmente las características de los motores disponibles y se averiguarán las velocidades máximas que puede alcanzar el mecanismo. Así podremos presentar un software que sirva para generar trayectorias para el robot 5R. Se presentan también, entre otros, el presupuesto del proyecto y los riesgos en los que se puede incurrir. El documento finaliza con unos anexos de planos CAD, resultados y código de programación.

The aquatic biota of the now extinct lacustrine complex of the Mexico basin

The commonest organisms of the original Mexico lake complex are listed, including those that exist today in the Lago Viejo. In addition, a brief hydraulic history of this endorheic basin is given.