Análise estatística das emissões de CO e HC produzidas por gases da exaustão veicular oriundos de gasolina, GNV e mistura álcool/gasolina

The vehicles are the main mobile sources of carbon monoxide (CO) and unburned hydrocarbons (HC) released into the atmosphere. In the last years the increment of the fleet of vehicles in the municipal district of Natal-RN it is contributing to the increase of the emissions of those pollutants. The study consisted of a statistical analysis of the emissions of CO and HC of a composed sample for 384 vehicles with mechanization Gasoline/CNG or Alcohol/Gasoline/CNG of the municipal district of Natal-RN. The tests were accomplished in vehicles submitted to Vehicular Safety's Inspection, in the facilities of INSPETRANS, Organism of Vehicular Inspection. An partial gases analyzer allowed to measure, for each vehicle, the levels of CO and HC in two conditions of rotation of the motor (900 and 2500 rpm). The statistical analysis accomplished through the STATISTICA software revealed a sensitive reduction in the efficiency of the converters catalytic after 6 years of use with emission average it is of 0,78% of CO and 156 (ppm) of HC, Which represents approximately 4 (four) times the amount of CO and the double of HC in comparison with the newest vehicles. The result of a Student s t-test, suggests strongly that the average of the emissions of HC (152 ppm), at 900 rpm, is 40% larger than at 2500 rpm, for the motor without load. This result reveals that the efficiency of the catalytic conversion is limited kinetically in low engine speeds. The Study also ends that when comparing the emissions of CO and HC considering the influence of the fuels, it was verified that although the emissions of CO starting from CNG are 62% smaller than arising from the gasoline, there are not significant differences among the emissions of HC originating from of CNG and of the gasoline. In synthesis, the results place the current criteria of vehicular inspection, for exhaust gases, in doubt, leading the creation of emission limits of pollutant more rigorous, because the efficiency of the converters catalytic is sensibly reduced starting from 6 years of use. It is also raised the possibility of modifications in the test conditions adopted by the current norms, specifically in the speed engine, have seen that in the condition without load the largest emission indexes were registered in slow march. That fact that allows to suggest the dismissal of the tests in high speed engine, reducing the time of inspection in half and generating economy of fuel

Influência da corrente de pulso, do tempo de pulso e diâmetro de gota sobre a estabilidade da transferência metálica no processo MIG-P

To obtain a process stability and a quality weld bead it is necessary an adequate parameters set: base current and time, pulse current and pulse time, because these influence the mode of metal transfer and the weld quality in the MIG-P, sometimes requiring special sources with synergistic modes with external control for this stability. This work aims to analyze and compare the effects of pulse parameters and droplet size in arc stability in MIG-P, four packets of pulse parameters were analysed: Ip = 160 A, tp = 5.7 ms; Ip = 300 A and tp = 2 ms, Ip = 350 A, tp = 1.2 ms and Ip = 350 A, tp = 0.8 ms. Each was analyzed with three different drop diameters: drop with the same diameter of the wire electrode; droplet diameter larger drop smaller than the diameter of the wire electrode. For purposes of comparison the same was determined relation between the average current and welding speed was determined generating a constant (Im / Vs = K) for all parameters. Welding in flat plate by simple deposition for the MIG-P with a distance beak contact number (DBCP) constant was perfomed subsequently making up welding in flat plate by simple deposition with an inclination of 10 degrees to vary the DBCP, where by assessment on how the MIG-P behaved in such a situation was possible, in addition to evaluating the MIG-P with adaptive control, in order to maintain a constant arc stability. Also high speed recording synchronized with acquiring current x voltage (oscillogram) was executed for better interpretation of the transfer mechanism and better evaluation in regard to the study of the stability of the process. It is concluded that parameters 3 and 4 exhibited greater versatility; diameters drop equal to or slightly less than the diameter of the wire exhibited better stability due to their higher frequency of detachment, and the detachment of the drop base does not harm the maintenance the height of the arc

Aplicação de ultrassons no deslocamento de petróleo em meio poroso

The objective of this study was to evaluate the displacement of petroleum/diesel solutions, at different concentrations, observing the effect of ultrasonic vibrations in fluids present in porous media to obtain an increase in oil production. The bubbles produced by ultrasound implode asymmetrically in the rock, generating liquid jets with high speed, displacing the oil present in porous media. The oil/diesel solutions were prepared with concentrations ranging from 20 g/L to 720 g/L in oil in relation to diesel and its viscosities were obtained in a Brookfield Rheometer RS2000, with temperature ranging from 25 to 55 °C. After, calculations were performed to obtain the activation energy data for oil/diesel solutions. For oil recovery experiments, cylindrical samples of porous rock (core samples), with resin around the perimeter and its two circular bases free to allow the passage of fluids, were first saturated with 2% KCl solution and after with oil solutions. The results of oil extraction were satisfactory for all studied solutions, being obtained up to 68% partial displacement with saline solution injection. The ultrasound system was used after saline injection, increasing oil displacement, with oil extractions ranging from 63% to 79%. During the experiments, it was observed the warming of core samples, helping to reduce the viscosity of more concentrated systems, and consequently enhancing the percentage of advanced recovery for all studied solutions

Desenvolvimento de um secador spray para obtenção de pós finos de precursores de nióbio

This work presents a spray-dryer designed to oxalate-niobate precursors and suitable for the production of Niobium Carbide. The dryer was intended to produce powders of controlled particle size. First, the precursor is dissolved in water to produce a solution of known concentration and then it is atomized on the spray-dryer to produce the powder. This equipment consists of a 304 stainless steel chamber, 0.48 m x 1.9 m (diameter x length), with a conical shape at the lower portion, which is assembled on a vertical platform. The chamber is heated by three 4 kW electrical resistances. In this process, drying air is heated as it flows inside a serpentine surrounding the chamber, in contrary to more traditional processes in which the hot drying air is used to heat the component. The air enters the chamber at the same temperature of the chamber, thus avoiding adherence of particles on the internal surface. The low speed flow is concurrent, directed from the top to the bottom portion of the chamber. Powders are deposited on a 0.4 m diameter tray, which separates the cylindrical portion from the conical portion of the chamber. The humid air is discharged though a plug placed underneath the collecting tray. A factorial experimental planning was prepared to study the influence of five parameters (concentration, input flow, operation temperature, drying air flow and spray air flow) on the characteristics of the powders produced. Particle size distribution and shape were measured by laser granulometry and scanning electronic microscopy. Then, the powders are submitted to reaction in a CH4 / H2 atmosphere to compare the characteristics of spray-dried powders with powders synthetizided by conventional methods

Flavonoids and a naphthopyranone from Eriocaulon ligulatum and their mutagenic activity

A new acylated flavonoid, 6,4'-dimethoxyquereetin-3-O-beta-D-6 ''[3,4,5-trihydroxy (E)-cinnamoyl]glucopyranoside, and a naphthopyranone dimer, named eriocauline, together with 2 other known flavonoids, 6-methoxyapigenin-7-O-beta-D-glucopyranoside and 6-methoxyapigenin-7-O-beta-D-allopyranoside, have been isolated from the capitulae of Eriocaulon ligulatum. The compounds were identified using spectroscopic methods (HR-ESI-MS, and 1-D and 2-D NMR). The methanol extract exhibited mutagenic activity in the Salmonella/microsome assay, in strains TA100, TA97a and TA102 and for dichloromethane extract tested in strain TA98.

Caracterização da resistência do algodoeiro a Ramularia areola e variabilidade molecular do patógeno

This research was conducted with the aim to study the genetic and pathogenic structure of Ramularia areola isolates collected in Brazil and to characterize the resistance response in cotton plants to ramularia spot. The genetic variability of 28 isolates of R. areola was studied using RAPD markers. The pathogenicity evaluation was realized by the inoculation of 6 isolates on cotton varieties Guazuncho-2 (Gossypium hirsutum) and VH8-4602 (Gossypium barbadense). The inheritance of disease resistance was studied using an artificially inoculated population of F2 individuals derived from the intercross of Guazuncho-2 (susceptible variety) end VH8-4602 (resistant variety), and also the parents and F1 individuals. Molecular polymorphism between the G. hisutum varieties DeltaOpal (suscetible) and CNPA CO-11612 (resistant) was estimated by 118 SSR and 24 AFLP markers. The parental genotypes Guazuncho-2 and VH8-4602 were selected for mapping, and then Recombinant Inbred Lines (RIL´s) derived from this crossing were evaluated with SSR 12 markers. The analysis of population structure of R. areola revealed that the three subpopulations were genetically simillar (Gst=0.18), and the isolates from Goiás and Minas Gerais were more similar to each other (0,92). This probability can be related to the relatively high gene flow among the three subpopulations (Nm=2.20). The isolates R. areola 9.1, from Minas Gerais State and 8.1 and 8.3 from Goiás State were the most aggressive ones to the susceptible variety Guazuncho-2. The variety VH8-4602 presented high level of resistance to ramularia spot. No differential interaction was observed between the pathogens and the analyzed varieties, and the resistance was classified as horizontal. The quantification of disease by number of necrotic lesions and number of spores in individual plants of F1 and F2 generations from the crossing between the varieties Guazuncho-2 and VH8-4602 presented continuous distribution, suggesting polygenic resistance. The resistance is probabilly recessive, since necrotic lesions and sporulation were observed on F1 plants. The molecular polymorphism between DeltaOpal e CNPA CO-11612 lineages was low (6%), then would be difficult to accomplish molecular mapping of disease resistance using this intercross. With the genotyping of the RIL s it was verified that 25% of the markers segregated in the proportions proposed by Mendel s Law and 75% of the studied markers presented segregation distortion in favor to the parental G. hirsutum. Both the low genetic variability of the pathogen and the number of resistance genes suggest that durable genetic resitance may be achieved

Avaliação microscópica dos fragmentos ósseos obtidos por diferentes métodos de osteotomia e de irrigação em aloenxertos irradiados e congelados de coelho

Oral and facial bone defects can undertake appearance, psychosocial well-being and stomathognatic function of its patients. Over the yerars several strategies for bone defect regeneration have arised to treat these pathologies, among them the use of frozen and irradiated bone allograft. Manipulation of bone grafts it s not determined yet, and several osteotomy alternatives can be observed. The present work evaluated with a microscope the bone fragments obtained from different osteotomy methods and irrigation on rings and blocks allografts irradiated and frozen at 80° negative in a rabbit model. The study is experimental in vitro and it sample was an adult male New Zealand rabbit. The animal was sacrificed to obtain long bones, that were submitted to freezing at 80º negative and irradiated with Cobalt- 60. Then the long bones were sectioned into 24 bone pieces, divided into 4 groups: G1 (n=06) osteotomy was performed with bur No. 6 forming rings with 5 mm thickness with high-speed handpiece with manual irrigation; G2 (n=06) osteotomy was performed with bur No. 6 forming rings with 5 mm thick with surgical motor with a manual irrigation rotation 1500 rpm; GA (n=06), osteotomy with trephine using manual irrigation with saline; and GB (n=06), osteotomy with trephine using saline from peristaltic pumps of surgical motor. Five bone pieces of each group were prepared for analysis on light microscopy (LM) and one on electronic scan electronic microscopy (SEM). On the SEM analysis edges surface, presence of microcracks and Smear Layer were evaluated. Analyzing osteotomy technics on SEM was observed: increased presence of microcracks cutting with high speed; increased presence of areas covered by Smear Layer when cutting with motor implant. The irrigation analysis with SEM was observed: that the presence of microcracks does not depend on the type of irrigation; on manual irrigation, there was greater discrepancy between the cutting lines. The descriptive analysis of the osteotomy and irrigation process on LM showed: histological analysis showing the bony margins with clear tissue changed layer, composed of blackened tissue of charred appearance near to the cortical bone; on the edges of the bony part, bone fragments that were displaced during the bone cut and bone irregularities were observed. After analysis of results we can conclude: that there was greater regularity of the bone cut using high-speed handpiece than using motor implant; the cut with trephine using saline irrigated from peristaltic pumps of surgical motor showed greater homogeneity when compared with manual irrigation; charred tissue was found in all obtained bone samples, whit no significant statistically difference on the proportion of carbonization of the two analysed technics

A Perda Auditiva Induzida pelo Ruído (PAIR) na formação odontológica: conhecimentos e níveis de exposição

The rationalization of work in the Dentistry has been taking the professional to work for ways and systems based in the ergonomics, turning their work efficient and less tiring. Since their academic formation, the dentists surgeons are concerned with the high productivity in clinic and with the final result of the work, neglecting the way as it is executed, which reduce their work capacity and exhibits them to occupational diseases that could be minimized and/or forewarned. This research had as the main objective to investigate the knowledge of the Dentistry academics of Rio Grande do Norte Federal University concerning the Noise-induced Hearing Loss (NIHL), relating them at the noise levels that they are exposed, as well as to the preventive measures taken during the clinical activities. Was observed that 95% of the individuals know that the dentist surgeon is a professional in risk for NIHL. Among the causes of NIHL, the one that obtained the largest frequency citation was the high-speed handpieces, reminded by 92,4% of the academics. Among the students which enumerated protective measures for NIHL, 92% mentioned the use of the ear plugs, although 97% of the researched have told do not use any kind of preventive measure related to the noise. Was also observed that 96% of the academics notice the noise during the clinical attendance, what inconvenience 28,1% of them. Related the noise levels, the high-speed handpieces of the academics presented a medium value of 80,5 dB varying from 72,3 to 88,3 dB. The average of the ambient noise observed at the Integrated Clinic was about 74,8 dB. In spite of the noise levels in this research were observed below the established limits of tolerance by the legislation, they can provoke damages to the Dentistry professionals' health, or that suggests the need of an intervention and use of immediate preventive measures able to generate a healthy atmosphere of work and less risky

Waveshapes of continuing currents and properties of M-components in natural positive cloud-to-ground lightning

This work analyses the waveshapes of continuing currents and parameters of M-components in positive cloud-to-ground (CG) flashes through high-speed GPS synchronized videos. The dataset is composed of only long continuing currents (with duration longer than 40 ms) and was selected from more than 800 flashes recorded in Sao Jose dos Campos (45.864 degrees W, 23.215 degrees S) and Uruguaiana (29.806 degrees W, 57.005 degrees S) in Southeast and South of Brazil, respectively, during 2003 to 2007 summers. The videos are compared with data obtained by the Brazilian Lightning Location System (BrasilDAT) in order to determine the polarity of each flash and select only positive cases. There are only two studies of waveshapes of continuing currents in the literature. One is based on direct current measurements of triggered lightning, in which four different types of waveshapes were observed; and the other is based on measurements of luminosity variations in high-speed videos of CG negative lightning, in which besides the four types above mentioned two additional types were observed. The present work is an extension of the latter, using the same method but now applied to obtain the waveshapes of positive CG lightning. As far as the authors know, this is the first report on M-components in positive continuing currents. We also have used the luminosity-versus-time graphs to observe their occurrence and measure some parameters (duration, elapsed time and time between two successive M-components), whose statistics are presented and compared in detail to the data for negative flashes. We have plotted a histogram of the M-components elapsed time over the total duration of the continuing current for positive flashes, which presented an exponential decay (correlation coefficient: 0.83), similar to what has been observed for negative flashes. (C) 2008 Elsevier B.V. All rights reserved.

Ocupação de área e interações de golfinhos-rotadores (Stenella longirostris) com o turismo náutico no Arquipélago de Noronha/PE, Brasil

Several works characterize the presence of spinner dolphins at Fernando de Noronha Archipelago in the Dolphins Bay. Though, the dolphins abidance inside this cove has decreased and a new area has been occupied by the animals to achieve the same behaviors, that are resting, breeding and nursing. This area comprises the Inside Sea northeast border of Fernando s de Noronha Island, including the opposing Middle and Dog shore area, the San Antonio Bay and the Between Islands region. The aim was to characterize the dolphins occupation and describe their interactions with the tourism in this area. Data were collected in 2008 and 2009 through a fixed point observation. The study area was divided into seven sub-areas, recording: presence/absence of dolphins, days abidance endurance, abidance length in each area, estimated number of individuals, dolphins direction and speed of displacement, boats presence, interaction period, monitoring, boats attitude and velocity. The dolphins abidance time displayed the same pattern during both years of study, with the higher occupancy in the Between Islands region. Groups with farther than 200 individuals were more frequent both 2008 (46.2%) and 2009 (42.3%). Thus the displacement s slow speed as the preferred direction towards Rat Island also showed the same pattern in both years. The Between Islands region also presented the boats major abidance near the dolphins groups. Boats moved farther in slow speed (95%) than at high speed (5%). The legislation s compliance for the cetaceans protection occurred in 89.7% of 2.839 interactions between boats and spinners, in which this variable was recorded. Whenever boats moved at a slow speed during the meetings with spinner dolphins groups, animals also moved at a slow speed (n = 337), significantly more than the fast displacements (n = 128) ix or "porpoise" (n = 4) (X2 = 318.543, p = -0.001). When boats quickly passed by groups, a significant difference between the dolphins displacement speeds was observed (X2 = 18.264, p =- 0.001), however, the slow (47%) and fast (47% ) displacements frequency was equal, noted the difference with the porpoise displacements (6%), which had the lowest frequency. Data indicate the establishment of a new occupation pattern of the spinner dolphins at Fernando de Noronha, with the Between Islands area being of great importance to the dolphins habits and currently the main area of the boats meeting with the dolphins, showing the need of new conservation measures in this area

Properties of DLC films deposited by an oxyacetylene flame

Diamond-like carbon (DLC) films were obtained by spinning a tungsten carbide substrate at a high speed using an oxyacetylene flame. The films deposited at a typical experimental condition of substrate temperature of 810 degrees C, rotation of 600 rpm and 3 h deposition time, exhibited an uniform, very smooth, hard and glassy surface covering the entire exposed face of the substrate. These films were identified as DLC by their characteristic broad Raman spectra centered at 1554 cm(-1) and micro-Vicker's hardness > 3400 kg mm(-2). For substrate temperatures < 800 degrees C the film started losing the uniform glassy surface and the hardness deteriorated. For temperatures > 950 degrees C the film was still hard and shiny, but black in color. DLC films were also obtained in a wide range of speeds of rotation (300-750 rpm), as long as the temperature remained close to 850 degrees C. (C) 1999 Elsevier B.V. S.A. All rights reserved.

Análise da estrutura genética populacional da piraúna (cephalopholis fulva: serranidae) ao longo da costa e ilhas oceânicas brasileiras

Brazil has about 8,500 km of coastline and on this scale, fishing is a historically important source of animal protein for human consumption. The national fishing background shows a growth of marine fishery production until 1985 and within this period it was recorded a steady decline. From the year 2003 fishing statistics aim to some "recovery" of the total fisheries production, which probably is related to a change in industry practice. The target of commercial fishing became smaller species with low commercial value, but very abundants. The coney, Cephalopholis fulva (Serranidae), is one of these species that have been suffering a greater fishing pressure in recent years. In order to provide data about the current situation of the genetic diversity of these populations, several molecular markers have been being used for this purpose. The prior knowledge of genetic variability is crucial for management and biodiversity conservation. To this end, the control region sequences (dloop) of mtDNA from Cephalopholis fulva (Serranidae) from five geographical points of the coast of Brazil (Ceará, Rio Grande do Norte, Bahia and Espírito Santo) and the Archipelago of Fernando de Noronha (FN) were sequenced and their genetic diversity analyzed. The FST values were very low (0.0246 to 0.000), indicating high gene flow between the sampled spots. The indices h and indicate a secondary contact between previously allopatric lineages differentiated or large and stable populations with long evolutionary history. Tests of Tajima and Fu showed expansion for all populations. In contrast, the mismatch distribution and SSD indicated expansion just for coastal populations. Unlike other species of the Atlantic which have been deeply affected by events on later Pleistocene, the population-genetic patterns of C. fulva may be related to recent events occurred approximately 130,000 years ago. Moreover, the data presented by geographical samples of the specie C. fulva showed high genetic diversity, also indicating the absence of deleterious effects of over-exploitation on this specie, as well as evidence of complete panmixia between all sampled populations

Alterações do pH, da P O2 e da P CO2 arteriais e da concentração de lactato sangüíneo de cavalos da raça Árabe durante exercício em esteira de alta velocidade

Avaliaram-se as alterações do pH, da P O2 e da P CO2 do sangue arterial e da concentração de lactato sangüíneo de 11 cavalos adultos da raça Árabe, submetidos a exercício progressivo em esteira de alta velocidade. Antes do exercício, no intervalo dos 15 segundos finais de cada mudança de velocidade e aos 1, 3 e 5 minutos após o término do exercício foram coletadas amostras de sangue arterial e venoso para a mensuração dos gases sangüíneos e da concentração de lactato. O exercício resultou em diminuição do pH, da pressão parcial de O2 (P O2) e da pressão parcial de CO2 (P CO2). A concentração de lactato sangüíneo elevou-se exponencialmente a partir da velocidade de 8,0m/s até os momentos após término do exercício.

Malondialdeído e troponina I cardíaca em equinos da raça Puro Sangue Árabe submetidos ao exercício e à suplementação com vitamina E

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação com Doppler colorido e espectral da veia porta de cães

A perfusão total do fígado e suas contribuições relativas, pelo sistema portal e pela artéria hepática, podem estar alteradas por vários processos hepáticos, como doença hepato-celular difusa, neoplasia e shunts intra-hepáticos. O estudo do comportamento do fluxo sangüíneo nos vasos do fígado por meio da ultra-sonografia Doppler tem demonstrado que este é um método viável não-invasivo e de grande auxílio, principalmente na avaliação da hemodinâmica portal. São duas as modalidades de ultra-sonografia Doppler com maior aplicação na rotina para avaliação de fluxo nos vasos abdominais, o Doppler espectral e o Doppler colorido. Na doença hepática crônica, ocorre alteração da complacência hepática devido à fibrose ou à cirrose, as quais acarretam alterações vasculares, levando ao aumento da pressão venosa portal. As principais indicações desse exame são os casos em que há suspeita de hipertensão portal. A hemodinâmica portal é avaliada pela mensuração de sua área, da velocidade média, do volume de fluxo no vaso e do índice de congestão portal. Esta revisão de literatura tem como objetivo descrever os princípios físicos básicos da ultra-sonografia Doppler e sua aplicação na avaliação da hemodinâmica portal nos cães.