Thermoelectric performance of p-type TiCoSb half-Heusler compounds - Intrinsic phase separation and charge carrier concentration optimization as key to high efficiency

The world's rising demand of energy turns the development of sustainable and more efficient technologies for energy production and storage into an inevitable task. Thermoelectric generators, composed of pairs of n-type and p-type semiconducting materials, di¬rectly transform waste heat into useful electricity. The efficiency of a thermoelectric mate¬rial depends on its electronic and lattice properties, summarized in its figure of merit ZT. Desirable are high electrical conductivity and Seebeck coefficients, and low thermal con¬ductivity. Half-Heusler materials are very promising candidates for thermoelectric applications in the medium¬ temperature range such as in industrial and automotive waste heat recovery. The advantage of Heusler compounds are excellent electronic properties and high thermal and mechanical stability, as well as their low toxicity and elemental abundance. Thus, the main obstacle to further enhance their thermoelectric performance is their relatively high thermal conductivity.rn rnIn this work, the thermoelectric properties of the p-type material (Ti/Zr/Hf)CoSb1-xSnx were optimized in a multistep process. The concept of an intrinsic phase separation has recently become a focus of research in the compatible n-type (Ti/Zr/Hf)NiSn system to achieve low thermal conductivities and boost the TE performance. This concept is successfully transferred to the TiCoSb system. The phase separation approach can form a significant alternative to the previous nanostructuring approach via ball milling and hot pressing, saving pro¬cessing time, energy consumption and increasing the thermoelectric efficiency. A fundamental concept to tune the performance of thermoelectric materials is charge carrier concentration optimization. The optimum carrier concentration is reached with a substitution level for Sn of x = 0.15, enhancing the ZT about 40% compared to previous state-of-the-art samples with x = 0.2. The TE performance can be enhanced further by a fine-tuning of the Ti-to-Hf ratio. A correlation of the microstructure and the thermoelectric properties is observed and a record figure of merit ZT = 1.2 at 710°C was reached with the composition Ti0.25Hf0.75CoSb0.85Sn0.15.rnTowards application, the long term stability of the material under actual conditions of operation are an important issue. The impact of such a heat treatment on the structural and thermoelectric properties is investigated. Particularly, the best and most reliable performance is achieved in Ti0.5Hf0.5CoSb0.85Sn0.15, which reached a maximum ZT of 1.1 at 700°C. The intrinsic phase separation and resulting microstructure is stable even after 500 heating and cooling cycles.

Drug-eluting stents: limitations of early generation and progress with newer generation devices

The success of first generation drug-eluting stents, namely by reducing restenosis and the need of repeat revascularization procedures is hampered by some limitations affecting device safety. Intense research efforts helped to identify these shortcomings and direct research to develop newer generation drug-eluting stents with the potential to circumvent these drawbacks. This review will discuss limitations of early generation drug-eluting stents, focus on solutions provided by newer generation devices, and shed light on unresolved issues and potential future solutions.

Ortho Effect in the Bergman Cyclization: Electronic and Steric Effects in Hydrogen Abstraction by 1-Substituted Naphthalene 5,8-Diradicals

We present a detailed theoretical study of geometries, electronic structure, and energies of transition states and intermediates completing the full Bergman cycloaromatization pathway of ortho-substituted enediynes with a focus on polar and steric contributions to the kinetics and thermodynamics of hydrogen abstraction. This study provides a rare unambiguous example of remote substitution that affects reactivity of a neutral reactive intermediate through an σ framework.

Growth, modification and integration of carbon nanotubes into molecular electronics

Molecules are the smallest possible elements for electronic devices, with active elements for such devices typically a few Angstroms in footprint area. Owing to the possibility of producing ultrahigh density devices, tremendous effort has been invested in producing electronic junctions by using various types of molecules. The major issues for molecular electronics include (1) developing an effective scheme to connect molecules with the present micro- and nano-technology, (2) increasing the lifetime and stabilities of the devices, and (3) increasing their performance in comparison to the state-of-the-art devices. In this work, we attempt to use carbon nanotubes (CNTs) as the interconnecting nanoelectrodes between molecules and microelectrodes. The ultimate goal is to use two individual CNTs to sandwich molecules in a cross-bar configuration while having these CNTs connected with microelectrodes such that the junction displays the electronic character of the molecule chosen. We have successfully developed an effective scheme to connect molecules with CNTs, which is scalable to arrays of molecular electronic devices. To realize this far reaching goal, the following technical topics have been investigated. 1. Synthesis of multi-walled carbon nanotubes (MWCNTs) by thermal chemical vapor deposition (T-CVD) and plasma-enhanced chemical vapor deposition (PECVD) techniques (Chapter 3). We have evaluated the potential use of tubular and bamboo-like MWCNTs grown by T-CVD and PE-CVD in terms of their structural properties. 2. Horizontal dispersion of MWCNTs with and without surfactants, and the integration of MWCNTs to microelectrodes using deposition by dielectrophoresis (DEP) (Chapter 4). We have systematically studied the use of surfactant molecules to disperse and horizontally align MWCNTs on substrates. In addition, DEP is shown to produce impurityfree placement of MWCNTs, forming connections between microelectrodes. We demonstrate the deposition density is tunable by both AC field strength and AC field frequency. 3. Etching of MWCNTs for the impurity-free nanoelectrodes (Chapter 5). We show that the residual Ni catalyst on MWCNTs can be removed by acid etching; the tip removal and collapsing of tubes into pyramids enhances the stability of field emission from the tube arrays. The acid-etching process can be used to functionalize the MWCNTs, which was used to make our initial CNT-nanoelectrode glucose sensors. Finally, lessons learned trying to perform spectroscopic analysis of the functionalized MWCNTs were vital for designing our final devices. 4. Molecular junction design and electrochemical synthesis of biphenyl molecules on carbon microelectrodes for all-carbon molecular devices (Chapter 6). Utilizing the experience gained on the work done so far, our final device design is described. We demonstrate the capability of preparing patterned glassy carbon films to serve as the bottom electrode in the new geometry. However, the molecular switching behavior of biphenyl was not observed by scanning tunneling microscopy (STM), mercury drop or fabricated glassy carbon/biphenyl/MWCNT junctions. Either the density of these molecules is not optimum for effective integration of devices using MWCNTs as the nanoelectrodes, or an electroactive contaminant was reduced instead of the ionic biphenyl species. 5. Self-assembly of octadecanethiol (ODT) molecules on gold microelectrodes for functional molecular devices (Chapter 7). We have realized an effective scheme to produce Au/ODT/MWCNT junctions by spanning MWCNTs across ODT-functionalized microelectrodes. A percentage of the resulting junctions retain the expected character of an ODT monolayer. While the process is not yet optimized, our successful junctions show that molecular electronic devices can be fabricated using simple processes such as photolithography, self-assembled monolayers and dielectrophoresis.

Development of a high performance parallel computing platform and its use in the study of nanostructures : clusters, sheets and tubes .

Small clusters of gallium oxide, technologically important high temperature ceramic, together with interaction of nucleic acid bases with graphene and small-diameter carbon nanotube are focus of first principles calculations in this work. A high performance parallel computing platform is also developed to perform these calculations at Michigan Tech. First principles calculations are based on density functional theory employing either local density or gradient-corrected approximation together with plane wave and gaussian basis sets. The bulk Ga2O3 is known to be a very good candidate for fabricating electronic devices that operate at high temperatures. To explore the properties of Ga2O3 at nonoscale, we have performed a systematic theoretical study on the small polyatomic gallium oxide clusters. The calculated results find that all lowest energy isomers of GamOn clusters are dominated by the Ga-O bonds over the metal-metal or the oxygen-oxygen bonds. Analysis of atomic charges suggest the clusters to be highly ionic similar to the case of bulk Ga2O3. In the study of sequential oxidation of these slusters starting from Ga2O, it is found that the most stable isomers display up to four different backbones of constituent atoms. Furthermore, the predicted configuration of the ground state of Ga2O is recently confirmed by the experimental result of Neumark's group. Guided by the results of calculations the study of gallium oxide clusters, performance related challenge of computational simulations, of producing high performance computers/platforms, has been addressed. Several engineering aspects were thoroughly studied during the design, development and implementation of the high performance parallel computing platform, rama, at Michigan Tech. In an attempt to stay true to the principles of Beowulf revolutioni, the rama cluster was extensively customized to make it easy to understand, and use - for administrators as well as end-users. Following the results of benchmark calculations and to keep up with the complexity of systems under study, rama has been expanded to a total of sixty four processors. Interest in the non-covalent intereaction of DNA with carbon nanotubes has steadily increased during past several years. This hybrid system, at the junction of the biological regime and the nanomaterials world, possesses features which make it very attractive for a wide range of applicatioins. Using the in-house computational power available, we have studied details of the interaction between nucleic acid bases with graphene sheet as well as high-curvature small-diameter carbon nanotube. The calculated trend in the binding energies strongly suggests that the polarizability of the base molecules determines the interaction strength of the nucleic acid bases with graphene. When comparing the results obtained here for physisorption on the small diameter nanotube considered with those from the study on graphene, it is observed that the interaction strength of nucleic acid bases is smaller for the tube. Thus, these results show that the effect of introducing curvature is to reduce the binding energy. The binding energies for the two extreme cases of negligible curvature (i.e. flat graphene sheet) and of very high curvature (i.e. small diameter nanotube) may be considered as upper and lower bounds. This finding represents an important step towards a better understanding of experimentally observed sequence-dependent interaction of DNA with Carbon nanotubes.

Feasibility and acceptance of electronic quality of life assessment in general practice: an implementation study

Background Patients' health related quality of life (HRQoL) has rarely been systematically monitored in general practice. Electronic tools and practice training might facilitate the routine application of HRQoL questionnaires. Thorough piloting of innovative procedures is strongly recommended before the conduction of large-scale studies. Therefore, we aimed to assess i) the feasibility and acceptance of HRQoL assessment using tablet computers in general practice, ii) the perceived practical utility of HRQoL results and iii) to identify possible barriers hindering wider application of this approach. Methods Two HRQoL questionnaires (St. George's Respiratory Questionnaire SGRQ and EORTC QLQ-C30) were electronically presented on portable tablet computers. Wireless network (WLAN) integration into practice computer systems of 14 German general practices with varying infrastructure allowed automatic data exchange and the generation of a printout or a PDF file. General practitioners (GPs) and practice assistants were trained in a 1-hour course, after which they could invite patients with chronic diseases to fill in the electronic questionnaire during their waiting time. We surveyed patients, practice assistants and GPs regarding their acceptance of this tool in semi-structured telephone interviews. The number of assessments, HRQoL results and interview responses were analysed using quantitative and qualitative methods. Results Over the course of 1 year, 523 patients filled in the electronic questionnaires (1–5 times; 664 total assessments). On average, results showed specific HRQoL impairments, e.g. with respect to fatigue, pain and sleep disturbances. The number of electronic assessments varied substantially between practices. A total of 280 patients, 27 practice assistants and 17 GPs participated in the telephone interviews. Almost all GPs (16/17 = 94%; 95% CI = 73–99%), most practice assistants (19/27 = 70%; 95% CI = 50–86%) and the majority of patients (240/280 = 86%; 95% CI = 82–91%) indicated that they would welcome the use of electronic HRQoL questionnaires in the future. GPs mentioned availability of local health services (e.g. supportive, physiotherapy) (mean: 9.4 ± 1.0 SD; scale: 1 – 10), sufficient extra time (8.9 ± 1.5) and easy interpretation of HRQoL results (8.6 ± 1.6) as the most important prerequisites for their use. They believed HRQoL assessment facilitated both communication and follow up of patients' conditions. Practice assistants emphasised that this process demonstrated an extra commitment to patient centred care; patients viewed it as a tool, which contributed to the physicians' understanding of their personal condition and circumstances. Conclusion This pilot study indicates that electronic HRQoL assessment is technically feasible in general practices. It can provide clinically significant information, which can either be used in the consultation for routine care, or for research purposes. While GPs, practice assistants and patients were generally positive about the electronic procedure, several barriers (e.g. practices' lack of time and routine in HRQoL assessment) need to be overcome to enable broader application of electronic questionnaires in every day medical practice.

Electronic Communications as a Distinct and Unique Object of Regulation

The present paper is an abridged version of the first chapter to the book EC Electronic Communications and Competition Law (London: Cameron May, 2007). It is intended to pinpoint the contours of the communications sector as an object of regulation - an exercise that is essential to any thoughts on appropriate regulatory design. The communications sector is defined through its salient features of being (i) network-bound; (ii) dynamic; (iii) converging; (iv) sensitive to regulation and society’s reactions; and as one (v) with special societal role and as (vi) part of the new economy.

A Divergent Path of Industrial Upgrading: Emergence and Evolution of the Mobile Handset Industry in China

Starting from almost null in the late 1990s, China's mobile phone handset industry has grown to account for more than 40 percent of the current world production. While export growth has been overwhelmingly led by multi-national corporations (MNCs), increasingly fierce competition in the domestic market ignited by the advent of local handset makers has induced unique industrial evolution: (1) outgrowth of independent design houses specialized in handset development and (2) emergence of IC fabless ventures that design core ICs for handsets. In the background of this evolutionary industrial growth there are factors such as, the scale and increasing diversity of China's domestic market that advantages local firms vis-a-vis MNCs; modularization of handset and semiconductor technologies; policy interventions that supports local startups. The emergence and evolution of China's handset industry is likely to have international implications as the growth of the global demand for low-cost and multi-function mobile phone handsets is expected to accelerate. Thus, our case suggests that the conventional view of latecomer industrialization and upgrading that emphasizes the key role of international production networks organized by MNCs needs to be modified in order to accommodate China's rise into perspective.

Innovation networks in China, Japan, and Korea : evidence from Japanese patent data

The growing importance of innovation in economic growth has encouraged the development of innovation capabilities in East Asia, within which China, Japan, and Korea are most important in terms of technological capabilities. Using Japanese patent data, we examine how knowledge networks have developed among these countries. We find that Japan's technological specialization saw little change, but those of Korea and China changed rapidly since 1970s. By the year 2009, technology specialization has become similar across three countries in the sense that the common field of prominent technology is "electronic circuits and communication technologies". Patent citations suggest that technology flows were largest in the electronic technology, pointing to the deepening of innovation networks in these countries.

Calculation Methodology and Fabrication Procedures for Particle Accelerator Strip-Line Kickers: Application to the CTF3 Combiner Ring Extraction Kicker and TL2 Tail Clippers

A particle accelerator is any device that, using electromagnetic fields, is able to communicate energy to charged particles (typically electrons or ionized atoms), accelerating and/or energizing them up to the required level for its purpose. The applications of particle accelerators are countless, beginning in a common TV CRT, passing through medical X-ray devices, and ending in large ion colliders utilized to find the smallest details of the matter. Among the other engineering applications, the ion implantation devices to obtain better semiconductors and materials of amazing properties are included. Materials supporting irradiation for future nuclear fusion plants are also benefited from particle accelerators. There are many devices in a particle accelerator required for its correct operation. The most important are the particle sources, the guiding, focalizing and correcting magnets, the radiofrequency accelerating cavities, the fast deflection devices, the beam diagnostic mechanisms and the particle detectors. Most of the fast particle deflection devices have been built historically by using copper coils and ferrite cores which could effectuate a relatively fast magnetic deflection, but needed large voltages and currents to counteract the high coil inductance in a response in the microseconds range. Various beam stability considerations and the new range of energies and sizes of present time accelerators and their rings require new devices featuring an improved wakefield behaviour and faster response (in the nanoseconds range). This can only be achieved by an electromagnetic deflection device based on a transmission line. The electromagnetic deflection device (strip-line kicker) produces a transverse displacement on the particle beam travelling close to the speed of light, in order to extract the particles to another experiment or to inject them into a different accelerator. The deflection is carried out by the means of two short, opposite phase pulses. The diversion of the particles is exerted by the integrated Lorentz force of the electromagnetic field travelling along the kicker. This Thesis deals with a detailed calculation, manufacturing and test methodology for strip-line kicker devices. The methodology is then applied to two real cases which are fully designed, built, tested and finally installed in the CTF3 accelerator facility at CERN (Geneva). Analytical and numerical calculations, both in 2D and 3D, are detailed starting from the basic specifications in order to obtain a conceptual design. Time domain and frequency domain calculations are developed in the process using different FDM and FEM codes. The following concepts among others are analyzed: scattering parameters, resonating high order modes, the wakefields, etc. Several contributions are presented in the calculation process dealing specifically with strip-line kicker devices fed by electromagnetic pulses. Materials and components typically used for the fabrication of these devices are analyzed in the manufacturing section. Mechanical supports and connexions of electrodes are also detailed, presenting some interesting contributions on these concepts. The electromagnetic and vacuum tests are then analyzed. These tests are required to ensure that the manufactured devices fulfil the specifications. Finally, and only from the analytical point of view, the strip-line kickers are studied together with a pulsed power supply based on solid state power switches (MOSFETs). The solid state technology applied to pulsed power supplies is introduced and several circuit topologies are modelled and simulated to obtain fast and good flat-top pulses.

Substrate nanopatterning by e-beam lithography to growth ordered arrays of III-nitride nanodetectors, white light emitters, and solar cells

III-nitride nanorods have attracted much scientific interest during the last decade because of their unique optical and electrical properties [1,2]. The high crystal quality and the absence of extended defects make them ideal candidates for the fabrication of high efficiency opto-electronic devices such as nano-photodetectors, light-emitting diodes, and solar cells [1-3]. Nitride nanorods are commonly grown in the self-assembled mode by plasma-assisted molecular beam epitaxy (MBE) [4]. However, self-assembled nanorods are characterized by inhomogeneous heights and diameters, which render the device processing very difficult and negatively affect the electronic transport properties of the final device. For this reason, the selective area growth (SAG) mode has been proposed, where the nanorods preferentially grow with high order on pre-defined sites on a pre-patterned substrate

Understanding the Selective Area Nucleation and Growth of GaN nanocolumns by MBE using Ti nanomasks

•Self- assembled Ga(In)N Nanorods and Nanostructures •Ordered growth of GaN Nanorods: masks issues •Ordered growth of GaN Nanorods: mechanisms •White NanoLEDs

MBE growth and characterization of InGaN-based films and nanocolumns on Silicon substrates and GaN templates

InN layers: MBE growth issues Growth of InN-based thin films: InN/InGaN QWS on GaN Growth of InN-based nanorods ● Self Self-assembled assembled InN InN nanorods nanorods onon different different substrates substrates ● Self-assembled InGaN nanorods ● Broad- Broad-emission emission nanostructures ● Self Self--assembled assembled InGaN InGaN--based based Qdisks Qdisks ● Selective area growth (SAG) of InGaN Qdisks

WiMAX,Technology and Market.

Wireless communication is the transfer of information from one place to another without using wires. From the earliest times, humans have felt the need to develop techniques of remote communication. From this need arose the smoke signals, communication by sun reflection in mirrors and so on. But today the telecommunications electronic devices such as telephone, television, radio or computer. Radio and television are used for one-way communication. Telephone and computer are used for two-way communication. In wireless networks there is almost unlimited mobility, we can access the network almost anywhere or anytime. In wired networks we have the restriction of using the services in fixed area services. The demand of the wireless is increasing very fast; everybody wants broadband services anywhere anytime. WiMAX (Worldwide Interoperability for Microwave Access) is a broadband wireless technology based on IEEE 802.16-2004 and IEEE 802.16e-2005 that appears to solve this demand. WIMAX is a system that allows wireless data transmission in areas of up to 48 km of radius. It is designed as a wireless alternative to ADSL and a way to connect nodes in wireless metropolitan areas network. Unlike wireless systems that are limited in most cases, about 100 meter, providing greater coverage and more bandwidth. WIMAX promises to achieve high data transmission rates over large areas with a great amount of users. This alternative to the networks of broadband access common as DSL o Wi-Fi, can give broadband access to places quickly to rural areas and developing areas around the world. This paper is a study of WIMAX technology and market situation. First, the paper is responsible for explaining the technical aspects of WIMAX. For this gives an overview of WIMAX standards, physical layer, MAC layer and WiMAX, Technology and Market Beijing University of Post and Telecommunications 2 WIMAX network architecture. Second, the paper address the issue of market in which provides an overview of development and deployment of WIMAX to end the future development trend of WIMAX is addressed. RESUMEN: Por comunicaciones inalámbricas se entiende la transferencia de información desde un lugar a otro sin la necesidad de un soporte físico como es por ejemplo el cable. Por lo que remontándose a los principios de la existencia del ser humano, nos damos cuenta de que el ser humano siempre ha sentido la necesidad de desarrollar técnicas para lograr comunicarse a distancia con sus semejantes. De dicha necesidad, surgieron técnicas tan ancestrales como puede ser la comunicación mediante señales de humo o por reflexión de los rayos solares en espejos entre otras. La curiosidad del ser humano y la necesidad de comunicarse a distancia fue la que llevó a Alexander Graham Bell a inventar el teléfono en 1876. La aparición de un dispositivo que permitía comunicarse a distancia permitiendo escuchar la voz de aquella persona con la que se quería hablar, supuso una revolución no solo en el panorama tecnológico, si no también en el panorama social. Pues a parte de permitir comunicaciones a larga distancia, solventó el problema de la comunicación en “tiempo real”. A raíz de este invento, la tecnología en materia de comunicación ha ido avanzando significativamente, más concretamente en lo referido a las comunicaciones inalámbricas. En 1973 se realizó la primera llamada desde un terminal móvil aunque no fue hasta 1983 cuando se empezó a comercializar dicho terminal, lo que supuso un cambio de hábitos y costumbres para la sociedad. Desde la aparición del primer móvil el crecimiento del mercado ha sido exponencial, lo que ha repercutido en una demanda impensable de nuevas aplicaciones integradas en dichos dispositivos móviles que satisfagan las necesidades que día a día autogenera la sociedad. Tras conseguir realizar llamadas a larga distancia de forma inalámbrica, el siguiente paso fue la creación de los SMS (Short Message System) lo que supuso una nueva revolución además de abaratar costes al usuario a la hora de comunicarse. Pero el gran reto para la industria de las comunicaciones móviles surgió con la aparición de internet. Todo el mundo sentía la necesidad de poder conectarse a esa gran base de datos que es internet en cualquier parte y en cualquier momento. Las primeras conexiones a internet desde dispositivos móviles se realizaron a través de la tecnología WAP (Wireless Application Protocol) hasta la aparición de la tecnología GPRS que permitía la conexión mediante protocolo TCP/IP. A partir de estas conexiones han surgido otras tecnologías, como EDGE, HSDPA, etc., que permitían y permiten la conexión a internet desde dispositivos móviles. Hoy en día la demanda de servicios de red inalámbrica crece de forma rápida y exponencial, todo el mundo quiere servicios de banda ancha en cualquier lugar y en cualquier momento. En este documento se analiza la tecnología WiMAX ( Worldwide Interoperability for Microwave Access) que es una tecnología de banda ancha basada en el estándar IEEE 802.16 creada para brindar servicios a la demanda emergente en la banda ancha desde un punto de vista tecnológico, donde se da una visión de la parte técnica de la tecnología; y desde el punto de vista del mercado, donde se analiza el despliegue y desarrollo de la tecnología desde el punto de vista de negocio. WiMAX es una tecnología que permite la transmisión inalámbrica de datos en áreas de hasta 48Km de radio y que está diseñada como alternativa inalámbrica para ADSL y para conectar nodos de red inalámbrica en áreas metropolitanas. A diferencia de los sistemas inalámbricos existentes que están limitados en su mayoría a unos cientos de metros, WiMAX ofrece una mayor cobertura y un mayor ancho de banda que permita dar soporte a nuevas aplicaciones, además de alcanzar altas tasas de transmisión de datos en grandes áreas con una gran cantidad de usuarios. Se trata de una alternativa a las redes de acceso de banda ancha como DSL o Wi-Fi, que puede dar acceso de banda ancha a lugares tales como zonas rurales o zonas en vías de desarrollo por todo el mundo con rapidez. Existen dos tecnologías de WiMAX, WiMAX fijo (basado en el estándar IEEE 802.16d-2004) y WiMAX móvil (basado en el estándar IEEE 802.16e-2005). La tecnología fija está diseñada para comunicaciones punto a multipunto, mientras que la fija lo está para comunicaciones multipunto a multipunto. WiMAX móvil se basa en la tecnología OFDM que ofrece ventajas en términos de latencia, eficiencia en el uso del espectro y soporte avanzado para antenas. La modulación OFDM es muy robusta frente al multitrayecto, que es muy habitual en los canales de radiodifusión, frente al desvanecimiento debido a las condiciones meteorológicas y frente a las interferencias de RF. Una vez creada la tecnología WiMAX, poseedora de las características idóneas para solventar la demanda del mercado, ha de darse el siguiente paso, hay que convencer a la industria de las telecomunicaciones de que dicha tecnología realmente es la solución para que apoyen su implantación en el mercado de la banda ancha para las redes inalámbricas. Es aquí donde entra en juego el estudio del mercado que se realiza en este documento. WiMAX se enfrenta a un mercado exigente en el que a parte de tener que dar soporte a la demanda técnica, ha de ofrecer una rentabilidad económica a la industria de las comunicaciones móviles y más concretamente a las operadoras móviles que son quienes dentro del sector de las telecomunicaciones finalmente han de confiar en la tecnología para dar soporte a sus usuarios ya que estos al fin y al cabo lo único que quieren es que su dispositivo móvil satisfaga sus necesidades independientemente de la tecnología que utilicen para tener acceso a la red inalámbrica de banda ancha. Quizás el mayor problema al que se ha enfrentado WiMAX haya sido la situación económica en la que se encuentra el mundo. WiMAX a comenzado su andadura en uno de los peores momentos, pero aun así se presenta como una tecnología capaz de ayudar al mundo a salir hacia delante en estos tiempos tan duros. Finalmente se analiza uno de los debates existentes hoy en día en el sector de las comunicaciones móviles, WiMAX vs. LTE. Como se puede observar en el documento realmente una tecnología no saldrá victoriosa frente a la otra, si no que ambas tecnologías podrán coexistir y trabajar de forma conjunta.

Research on intermediate band solar cells and development of experimental techniques for their characterization under concentrated illumination

Abstract This work is a contribution to the research and development of the intermediate band solar cell (IBSC), a high efficiency photovoltaic concept that features the advantages of both low and high bandgap solar cells. The resemblance with a low bandgap solar cell comes from the fact that the IBSC hosts an electronic energy band -the intermediate band (IB)- within the semiconductor bandgap. This IB allows the collection of sub-bandgap energy photons by means of two-step photon absorption processes, from the valence band (VB) to the IB and from there to the conduction band (CB). The exploitation of these low energy photons implies a more efficient use of the solar spectrum. The resemblance of the IBSC with a high bandgap solar cell is related to the preservation of the voltage: the open-circuit voltage (VOC) of an IBSC is not limited by any of the sub-bandgaps (involving the IB), but only by the fundamental bandgap (defined from the VB to the CB). Nevertheless, the presence of the IB allows new paths for electronic recombination and the performance of the IBSC is degraded at 1 sun operation conditions. A theoretical argument is presented regarding the need for the use of concentrated illumination in order to circumvent the degradation of the voltage derived from the increase in the recombi¬nation. This theory is supported by the experimental verification carried out with our novel characterization technique consisting of the acquisition of photogenerated current (IL)-VOC pairs under low temperature and concentrated light. Besides, at this stage of the IBSC research, several new IB materials are being engineered and our novel character¬ization tool can be very useful to provide feedback on their capability to perform as real IBSCs, verifying or disregarding the fulfillment of the “voltage preservation” principle. An analytical model has also been developed to assess the potential of quantum-dot (QD)-IBSCs. It is based on the calculation of band alignment of III-V alloyed heterojunc-tions, the estimation of the confined energy levels in a QD and the calculation of the de¬tailed balance efficiency. Several potentially useful QD materials have been identified, such as InAs/AlxGa1-xAs, InAs/GaxIn1-xP, InAs1-yNy/AlAsxSb1-x or InAs1-zNz/Alx[GayIn1-y]1-xP. Finally, a model for the analysis of the series resistance of a concentrator solar cell has also been developed to design and fabricate IBSCs adapted to 1,000 suns. Resumen Este trabajo contribuye a la investigación y al desarrollo de la célula solar de banda intermedia (IBSC), un concepto fotovoltaico de alta eficiencia que auna las ventajas de una célula solar de bajo y de alto gap. La IBSC se parece a una célula solar de bajo gap (o banda prohibida) en que la IBSC alberga una banda de energía -la banda intermedia (IB)-en el seno de la banda prohibida. Esta IB permite colectar fotones de energía inferior a la banda prohibida por medio de procesos de absorción de fotones en dos pasos, de la banda de valencia (VB) a la IB y de allí a la banda de conducción (CB). El aprovechamiento de estos fotones de baja energía conlleva un empleo más eficiente del espectro solar. La semejanza antre la IBSC y una célula solar de alto gap está relacionada con la preservación del voltaje: la tensión de circuito abierto (Vbc) de una IBSC no está limitada por ninguna de las fracciones en las que la IB divide a la banda prohibida, sino que está únicamente limitada por el ancho de banda fundamental del semiconductor (definido entre VB y CB). No obstante, la presencia de la IB posibilita nuevos caminos de recombinación electrónica, lo cual degrada el rendimiento de la IBSC a 1 sol. Este trabajo argumenta de forma teórica la necesidad de emplear luz concentrada para evitar compensar el aumento de la recom¬binación de la IBSC y evitar la degradación del voltage. Lo anterior se ha verificado experimentalmente por medio de nuestra novedosa técnica de caracterización consistente en la adquisicin de pares de corriente fotogenerada (IL)-VOG en concentración y a baja temperatura. En esta etapa de la investigación, se están desarrollando nuevos materiales de IB y nuestra herramienta de caracterizacin está siendo empleada para realimentar el proceso de fabricación, comprobando si los materiales tienen capacidad para operar como verdaderas IBSCs por medio de la verificación del principio de preservación del voltaje. También se ha desarrollado un modelo analítico para evaluar el potencial de IBSCs de puntos cuánticos. Dicho modelo está basado en el cálculo del alineamiento de bandas de energía en heterouniones de aleaciones de materiales III-V, en la estimación de la energía de los niveles confinados en un QD y en el cálculo de la eficiencia de balance detallado. Este modelo ha permitido identificar varios materiales de QDs potencialmente útiles como InAs/AlxGai_xAs, InAs/GaxIni_xP, InAsi_yNy/AlAsxSbi_x ó InAsi_zNz/Alx[GayIni_y]i_xP. Finalmente, también se ha desarrollado un modelado teórico para el análisis de la resistencia serie de una célula solar de concentración. Gracias a dicho modelo se han diseñado y fabricado IBSCs adaptadas a 1.000 soles.