Thermal Efficiency of LPG and PNG-fired burners: Experimental and numerical studies

In the present work, the thermal efficiency of a conventional domestic burner is studied both experimentally and numerically for liquefied petroleum gas (LPG) and piped natural gas (PNG) fuels. Three-dimensional computational fluid dynamic (CFD) modeling of the steady-state flow, combustion and heat transfer to the vessel is reported for the first time in such burners. Based on the insights from the CFD model concerning the flow and heat transfer, design modifications in the form of a circular insert and a radiant sheet are proposed which are observed to increase thermal efficiency for LPG. For PNG, predictions showed that loading height was a much more important factor affecting efficiency than these design modifications and an optimal loading height could be identified. Experiments confirm these trends by showing an improvement in burner thermal efficiency of 2.5% for LPG with the modified design, and 10% for PNG with the optimal loading height, demonstrating that the CFD modeling approach developed in the present work is a useful tool to study domestic burners. (C) 2013 Elsevier Ltd. All rights reserved.

Effects of elastase and collagenase on the nonlinearity and anisotropy of porcine aorta

We use enzymatic manipulation methods to investigate the individual and combined roles of elastin and collagen on arterial mechanics. Porcine aortic tissues were treated for differing amounts of time using enzymes elastase and collagenase to cause degradation in substrate proteins elastin and collagen and obtain variable tissue architecture. We use equibiaxial mechanical tests to quantify the material properties of control and enzyme treated tissues and histological methods to visualize the underlying tissue microstructure in arterial tissues. Our results show that collagenase treated tissues were more compliant in the longitudinal direction as compared to control tissues. Collagenase treatment also caused a decrease in the tissue nonlinearity as compared to the control samples in the study. A one hour collagenase treatment was sufficient to cause fragmentation and degradation of the adventitial collagen. In contrast, elastase treatment leads to significantly stiffer tissue response associated with fragmented and incomplete elastin networks in the tissue. Thus, elastin in arterial walls distributes tensile stresses whereas collagen serves to reinforce the vessel wall in the circumferential direction and also contributes to tissue anisotropy. A microstructurally motivated strain energy function based on circumferentially oriented medial fibers and helically oriented collagen fibers in the adventitia is useful in describing these experimental results.

Revalidation of Natrix clerki Wall, 1925, an overlooked species in the genus Amphiesma Dumeril, Bibron & Dumeril, 1854 (Squamata: Natricidae)

Natrix clerki Wall, 1925, previously known from its sole holotype and considered a synonym of Amphiesma parallelum (Boulenger, 1890), is resurrected in the genus Amphiesma on the basis of the analysis of morphological variation in 28 specimens of ``Amphiesma parallelum'' auctorum, plus six living, unvouchered specimens discovered in Arunachal Pradesh and Nagaland, India, and one vouchered specimen from Talle Valley in Arunachal Pradesh. Specimens from northeast India (Nagaland), northern Myanmar, and China (Yunnan), previously identified as Amphiesma parallelum either in the literature or in museum's catalogues, are also here referred to A. clerki. The holotype of Amphiesma clerki is redescribed. As a consequence, the definition of Amphiesma parallelum is modified. A. parallelum inhabits the Khasi Hills and Naga Hills in Northeast India, whereas A. clerki has a wider range in the Eastern Himalayas, northern Myanmar and Yunnan (China). Amphiesma clerki differs from A. parallelum by its longer tail, dorsal scales more strongly keeled, scales of the first dorsal scale row strongly keeled vs. smooth, a postocular streak not interrupted at the level of the neck, and a much more vivid pattern on a darker background colour. Characters of species of the Amphiesma parallelum group, i.e. A. clerki, A. parallelum, A. bitaeniatum, A. platyceps and A. sieboldii are compared. A key to this group is provided.

A Disulfide Stabilized beta-Sandwich Defines the Structure of a New Cysteine Framework M-Superfamily Conotoxin

The structure of a new cysteine framework (-C-CC-C-C-C) ``M''-superfamily conotoxin, Mo3964, shows it to have a beta-sandwich structure that is stabilized by inter-sheet cross disulfide bonds. Mo3964 decreases outward K+ currents in rat dorsal root ganglion neurons and increases the reversal potential of the Na(V)1.2 channels. The structure of Mo3964 (PDB ID: 2MW7) is constructed from the disulfide connectivity pattern, i.e., 1-3, 2-5, and 4-6, that is hitherto undescribed for the ``M''-superfamily conotoxins. The tertiary structural fold has not been described for any of the known conus peptides. NOE (549), dihedral angle (84), and hydrogen bond (28) restraints, obtained by measurement of (h3)J(NC') scalar couplings, were used as input for structure calculation. The ensemble of structures showed a backbone root mean square deviation of 0.68 +/- 0.18 angstrom, with 87% and 13% of the backbone dihedral (phi, psi) angles lying in the most favored and additional allowed regions of the Ramachandran map. The conotoxin Mo3964 represents a new bioactive peptide fold that is stabilized by disulfide bonds and adds to the existing repertoire of scaffolds that can be used to design stable bioactive peptide molecules.

Self-assembled gold nanofilms as a simple, recoverable and recyclable catalyst for nitro-reduction

Hexaazamacrocycle (L) stabilized gold nanoparticles (AuNPs) were prepared by combining L with HAuCl4 center dot 3H(2)O in a variety of alcohol-water (1 : 1) mixtures. The dual roles of L as a reducing and stabilizing agent were exploited for the synthesis of AuNPs under the optimized ratio of L to Au3+ (2 : 1). Self-assembled gold nanofilms (AuNFs) were constructed at liquid-liquid interfaces by adding equal volumes of hexane to the dispersions of AuNPs in the alcohol-water systems. The nanofilms were formed spontaneously by shaking the two-phase mixture for a minute followed by standing. The alcohols explored for the self-assembly phenomenon were methanol, ethanol, i-propanol and t-butanol. The systems containing methanol or t-butanol resulted in AuNFs at the interfaces, whereas the other two alcohols were found not suitable and the AuNPs remained dispersed in the corresponding alcohol-water medium. The AuNFs prepared under suitable conditions were coated on a variety of surfaces by the dip and lift-off method/solvent removal approach. The AuNFs were characterized by UV-vis, SEM, TEM, AFM and contact angle measurement techniques. A coated glass-vial or cuvette was used as a catalytic reservoir for nitro-reduction reactions under ambient and aqueous conditions using NaBH4 as the reducing agent. The reduced products (amines) were extracted by aqueous work-up using ethyl acetate followed by evaporation of the organic layer; the isolated products required no further purification. The catalyst was recovered by simply decanting the reaction mixture whereupon the isolated catalyst remained coated inside the vessel. The recovered catalyst was found to be equally efficient for further catalytic cycles.

Urea-Functionalized Self-Assembled Molecular Prism for Heterogeneous Catalysis in Water

Reaction of a ditopic urea ``strut'' (L-1) with cis-(tmen)Pd(NO3)(2) yielded a 3+3] self-assembled molecular triangle (T)L-1 = 1,4-di(4-pyridylureido)benzene; tmen = N,N,N',N'-tetrame-thylethane-1,2-diamine]. Replacing cis-(tmen)Pd(NO3)(2) in the above reaction with an equimolar mixture of Pd(NO3)(2) and a clip-type donor (L-2) yielded a template-free multicomponent 3D trigonal prism (P) decorated with multiple urea moieties L-2 = 3,3'-(1H-1,2,4-triazole-3,5-diyl)dipyridine]. This prism (P) was characterized by NMR. spectroscopy, and the structure was confirmed by X-ray crystallography. The P was employed as an effective hydrogen-bond-donor catalyst for Michael reactions of a series of water-insoluble nitro-olefins in an aqueous medium. The P showed better catalytic activity compared to the urea based ligand L-1 and the triangle T. Moreover, the confined nanospace of P in addition to large product outlet windows makes this 3D architecture a perfect molecular vessel to catalyze Diels-Alder reactions of 9-hydroxymethylanthracene with N-substituted maleimide in the aqueous medium. The present results demonstrate new observations on catalytic aqueous Diels-Alder and Michael reactions in heterogeneous fashion employing a discrete 3D architecture of Pd(II). The prism was recycled by simple filtration and reused several tithes without significant loss of activity.

DESIGN REQUIREMENTS FOR DIRECT SUPERCRITICAL CARBON DIOXIDE RECEIVER DEVELOPMENT AND TESTING

This paper establishes the design requirements for the development and testing of direct supercritical carbon dioxide (sCO2) solar receivers. Current design considerations are based on the ASME Boiler and Pressure Vessel Code (BPVC). Section I (BPVC) considers typical boilers/superheaters (i.e. fired pressure vessels) which work under a constant low heat flux. Section VIII (BPVC) considers pressure vessels with operating pressures above 15 psig 2 bar] (i.e. unfired pressure vessels). Section III, Division I - Subsection NH (BPVC) considers a more detailed stress calculation, compared to Section I and Section VIII, and requires a creep-fatigue analysis. The main drawback from using the BPVC exclusively is the large safety requirements developed for nuclear power applications. As a result, a new set of requirements is needed to perform detailed thermal-structural analyses of solar thermal receivers subjected to a spatially-varying, high-intensity heat flux. The last design requirements document of this kind was an interim Sandia report developed in 1979 (SAND79-8183), but it only addresses some of the technical challenges in early-stage steam and molten-salt solar receivers but not the use of sCO2 receivers. This paper presents a combination of the ASME BPVC and ASME B31.1 Code modified appropriately to achieve the reliability requirements in sCO(2) solar power systems. There are five main categories in this requirements document: Operation and Safety, Materials and Manufacturing, Instrumentation, Maintenance and Environmental, and General requirements. This paper also includes the modeling guidelines and input parameters required in computational fluid dynamics and structural analyses utilizing ANSYS Fluent, ANSYS Mechanical, and nCode Design Life. The main purpose of this document is to serve as a reference and guideline for design and testing requirements, as well as to address the technical challenges and provide initial parameters for the computational models that will be employed for the development of sCO(2) receivers.

Visualization of dust explosion under microgravity conditions

The objective of this work was to apply visualization methods to the experimental study of cornstarch dust-air mixture combustion in a closed vessel volume under microgravity conditions. A dispersion system with a small scale of turbulence was used in the experiments. A gas igniter initiated combustion of the dust-air mixture in the central or top part of the vessel. Flame propagation through the quiescent mixture was recorded by a high-speed video camera. Experiments showed a very irregular flame front and irregular distribution of the regions with local reactions of re-burning behind the flame front. at a later stage of combustion. Heat transfer from the hot combustion products to the walls is shown to have an important role in the combustion development. The maximum pressure and maximum rate of pressure rise were higher for flame propagation from the vessel center than for flame developed from the top pan of the vessel. The reason for smaller increase of the rate of pressure rise, for the flame developed from the top of the vessel. in comparison with that developed from the vessel center, was much faster increase of the contact surface of the combustion gases with the vessel walls. It was found that in dust flames only small part of hear was released at the flame front, the remaining part being released far behind it.

Rossby Vortex Simulation on a Paraboloidal Coordinate System Using the Lattice Boltzmann Method

In this paper, we apply our compressible lattice Boltzmann model to a rotating parabolic coordinate system to simulate Rossby vortices emerging in a layer of shallow water flowing zonally in a rotating paraboloidal vessel. By introducing a scaling factor, nonuniform curvilinear mesh can be mapped to a flat uniform mesh and then normal lattice Boltzmann method works. Since the mass per unit area on the two-dimensional (2D) surface varies with the thickness of the water layer, the 2D flow seems to be "compressible" and our compressible model is applied. Simulation solutions meet with the experimental observations qualitatively. Based on this research, quantitative solutions and many natural phenomena simulations in planetary atmospheres, oceans, and magnetized plasma, such as the famous Jovian Giant Red Spot, the Galactic Spiral-vortex, the Gulf Stream, and the Kuroshio Current, etc,, can be expected.

Thermocapillary flow in an annular liquid layer painted on a moving fiber

In the present paper, a theoretical model is studied on the flow in the liquid annular film, which is ejected from a vessel with relatively higher temperature and painted on the moving solid fiber. A temperature gradient, driving a thermocapillary flow, is formed on the free surface because of the heat transfer from the liquid with relatively higher temperature to the environmental gas with relatively lower temperature. The thermocapillary flow may change the radii profile of the liquid film. This process analyzed is based on the approximations of lubrication theory and perturbation theory, and the equation of the liquid layer radii and the process of thermal hydrodynamics in the liquid layer are solved for a temperature distribution on the solid fiber.

Instability Analysis of Nonlinear Surface Waves in a Circular Cylindrical Container Subjected to a Vertical Excitation

Singular perturbation theory of two-time scale expansions was developed both in inviscid and weak viscous fluids to investigate the motion of single surface standing wave in a liquid-filled circular cylindrical vessel, which is subject to a vertical periodical oscillation. Firstly, it is assumed that the fluid in the circular cylindrical vessel is inviscid, incompressible and the motion is irrotational, a nonlinear evolution equation of slowly varying complex amplitude, which incorporates cubic nonlinear term, external excitation and the influence of surface tension, was derived from solvability condition of high-order approximation. It shows that when forced frequency is low, the effect of surface tension on mode selection of surface wave is not important. However, when forced frequency is high, the influence of surface tension is significant, and can not be neglected. This proved that the surface tension has the function, which causes free surface returning to equilibrium location. Theoretical results much close to experimental results when the surface tension is considered. In fact, the damping will appear in actual physical system due to dissipation of viscosity of fluid. Based upon weakly viscous fluids assumption, the fluid field was divided into an outer potential flow region and an inner boundary layer region. A linear amplitude equation of slowly varying complex amplitude, which incorporates damping term and external excitation, was derived from linearized Navier-Stokes equation. The analytical expression of damping coefficient was determined and the relation between damping and other related parameters (such as viscosity, forced amplitude and depth of fluid) was presented. The nonlinear amplitude equation and a dispersion, which had been derived from the inviscid fluid approximation, were modified by adding linear damping. It was found that the modified results much reasonably close to experimental results. Moreover, the influence both of the surface tension and the weak viscosity on the mode formation was described by comparing theoretical and experimental results. The results show that when the forcing frequency is low, the viscosity of the fluid is prominent for the mode selection. However, when the forcing frequency is high, the surface tension of the fluid is prominent. Finally, instability of the surface wave is analyzed and properties of the solutions of the modified amplitude equation are determined together with phase-plane trajectories. A necessary condition of forming stable surface wave is obtained and unstable regions are illustrated. (c) 2005 Elsevier SAS. All rights reserved.

Quantifying the Effects of Contact Duration, Loading Rate, and Approach Velocity on P-Selectin-PSGL-1 Interactions Using AFM

Kinetics and its regulation by extrinsic physical factors govern selectin-ligand interactions that mediate tethering and rolling of circulating cells on the vessel wall under hemodynamic forces. While the force regulation of off-rate for dissociation of selectin-ligand bonds has been extensively studied, much less is known about how transport impacts the on-rate for association of these bonds and their stability. We used atomic force microscopy (AFM) to quantify how the contact duration, loading rate, and approach velocity affected kinetic rates and strength of bonds of P-selectin interacting with P-selectin glycoprotein ligand I (PSGL-1). We found a saturable relationship between the contact time and the rupture force, a biphasic relationship between the adhesion probability and the retraction velocity, a piece-wise linear relationship between the rupture force and the logarithm of the loading rate, and a threshold relationship between the approach velocity and the rupture force. These results provide new insights into how physical factors regulate receptor-ligand interactions.

Estudio descriptivo de la carcasa de cerdos alimentados con diferentes niveles de inclusión de marango (Moringa oleifera L.)

El presente estudio se realizo en la granja porcina de la Universidad Nacional Agraria (UNA), ubicada en el kilometro 13 carretera Norte desvío a Sabana Grande, Managua, Nicaragua. Este estudio duró 28 semanas comprendidas entre el 15 de Agosto del año 2000 al 8 de Marzo del año 2001. El objetivo general de estudio fue: contribuir a definir la calidad de la canal de cerdos a través de procesos de engorda utilizando dietas no convencionales para establecer las potencialidades o viabilidad de éstas en producción, utilizando diferentes raciones: (T1) Concentrado 100%, (T2) Marango 30% + 70% Concentrado, (T3) Marango 48% + 52% de Concentrado. Se utilizaron 36 cerdos híbridos, formándose grupos de 12 cerdos por tratamiento. los cerdos se pesaron al inicio y luego cada 15 días hasta el momento de su sacrificio: 1er sacrificio y 2do sacrificio. En el primer sacrificio el T1 presento el mayor rendimiento en canal con un 71.28%, superando en un 9.32% al T2 y en un 17.53% al T3. En el segundo sacrificio el T2 presento el mayor rendimiento en canal con un 75.79%, superando en un 4.19% al T3 y en un 4.51% al T1. En el primer sacrificio se obtuvo una distribución similar entre los puntos de grasa dorsal de cada tratamiento, sin embargo el T1 alcanzo el mayor espesor de grasa dorsal con un promedio de 32.6 mm con una diferencia respecto al T2 de 10 mm y de 17 mm respecto al T3. En el segundo sacrificio se obtuvo una distribución variada entre los diferentes puntos de grasa dorsal de cada tratamiento, aquí el T1 siempre mantuvo el mayor espesor de grasa dorsal con promedio entre puntos de 32,6 mm con una diferencia respecto al T2 de 9.4 mm y de 12.2 mm respecto al T3. Se utilizó un análisis descriptivo, siendo las variables principales: rendimiento en canal (RC), peso vivo (PV), peso canal (PC), composición de la canal (CC), composición de la grasa (CG) y espesor de la grasa dorsal (EGD). los cerdos del T2 en el 1er sacrificio obtuvieron un mayor porcentaje de carne en comparación con los otros tratamientos, mientras que los cerdos del T3 obtuvieron el mayor porcentaje de costilla y hueso en comparación con los otros tratamientos. los cerdos del 2do sacrificio del T3 obtuvieron el mayor porcentaje de carne en comparación con los otros tratamientos, mientras que los cerdos del T1 obtuvieron el mayor porcentaje de costilla y el T2 obtuvo el mayor porcentaje de hueso y el menor porcentaje de grasa. El análisis estadístico demostró que para el primer sacrificio existieron diferencias altamente significativas con respecto al peso final, peso canal, rendimiento y significativo en el hueso. En el segundo sacrificio existieron diferencias significativas en grasa, costilla y en el porcentaje de carne. Se realizo un análisis de separación de medias según Tukey al 5% para los casos en que se encontraron diferencias significativas. Esta prueba se realizó con el fin de categorízar los tratamientos.

Thermocapillary Effect in a Thermal Rheological Jet

The process of die swell in polymer jets is an important feature within polymer processing and can be explained through a study of its rheological effects. The existence of a thermocapillary effect, driven by the gradient of its surface tension, should be considered when examining a thermal jet that has a non-uniform temperature distribution on its free surface, as in various polymer processings. Both the rheological effect and thermocapillary effect on die swell can be studied numerically through a finite element method as used on a two-dimensional and unsteady model, in which a Coleman-Noll second-order fluid model is employed. The results show that the expanding angle depends on both the rheological property of the fluid and the pressure at the vessel exit. Although both the thermocapillary and the rheological effects contribute to the cross-section expansion of the fluid jet, the latter is more important in determining the expansion.

Kinetic measurements of cell surface E-selectin/carbohydrate ligand interactions

Selectin/ligand interactions initiate the multistep adhesion and signaling cascades in the recruitment of leukocytes from circulation to inflamed tissues and may also play a role in tumor metastasis. Kinetic properties of these interactions are essential determinants governing blood-borne cells' tethering to and rolling on the vessel wall. Extending our recently developed micropipette method, we have measured the kinetic rates of E-selectin/ligand interactions. Red cells coated with an E-selectin construct were allowed to bind HL-60 or Colo-205 cells bearing carbohydrate ligands. Specific adhesions were observed to occur at isolated points, the frequency of which followed a Poisson distribution. These point attachments were formed at the same rate with both the HL-60 and Colo-205 cells (0.14 +/- 0.04 and 0.13 +/- 0.03 mum(2) s(-1) per unit density of E-selectin, respectively) but dissociated from the former at a rate twice as fast as did from the latter (0.92 +/- 0.23 and 0.44 +/- 0.10 s(-1), respectively). The reverse rates agree well with those measured by the flow chamber. The forward rates are orders of magnitude higher than those of Fc gamma receptors interacting with IgG measured under similar conditions, consistent with the rapid kinetics requirement for the function of E-selectin/ligand binding, which is to capture leukocytes on endothelial surfaces from flow.