ANALYSIS OF HYPORHEIC FLOW INDUCED BY A BAR IN A GRAVEL STREAM: AN EXPERIMENTAL STUDY

Pipelines are one of the safest means to transport crude oil, but are not spill-free. This is of concern in North America, due to the large volumes of crude oil shipped by Canadian producers and the lengthy network of pipelines. Each pipeline crosses many rivers, supporting a wide variety of human activities, and rich aquatic life. However, there is a knowledge gap on the risks of contamination of river beds due to oil spills. This thesis addresses this knowledge gap by focussing on mechanisms that transport water (and contaminants) from the free surface flow to the bed sediments, and vice-versa. The work focuses on gravel rivers, in which bed sediments are sufficiently permeable that pressure gradients caused by the interactions of flow with topographic elements (gravel bars), or changes in direction induce exchanges of water between the free surface flow and the bed, known as hyporheic flows. The objectives of the thesis are: to present a new method to visualize and quantify hyporheic flows in laboratory experiments; to conduct a novel series of experiments on hyporheic flow induced by a gravel bar under different free surface flows. The new method to quantify hyporheic flows rests on injections of a solution of dye and water. The method yielded accurate flow lines, and reasonable estimates of the hyporheic flow velocities. The present series of experiments was carried out in a 11 m long, 0.39 m wide, and 0.41 m deep tilting flume. The gravel had a mean particle size of 7.7 mm. Different free surface flows were imposed by changing the flume slope and flow depth. Measured hyporheic flows were turbulent. Smaller free surface flow depths resulted in stronger hyporheic flows (higher velocities, and deeper dye penetration into the sediment). A significant finding is that different free surface flows (different velocities, Reynolds number, etc.) produce similar hyporheic flows as long as the downstream hydraulic gradients are similar. This suggests, that for a specified bar geometry, the characteristics of the hyporheic flows depend on the downstream hydraulic gradients, and not or only minimally on the internal dynamics of the free surface flow.

Fatty acid synthesis from U-14C glucose, U-14C fructose, L-U-14C alanine and 3H2O in liver slices and adipose tissue from Bar-Harbor obese-hyperglycemic mice.

info:eu-repo/semantics/published

Human exposure to particulate and gaseous pollutants in a bar.

There is increasing evidence of a causal link between airborne particles and ill health and this study examined the exposure to both airborne particles and the gas phase contaminants of environmental tobacco smoke (ETS) in a bar. The work reported here utilized concurrent and continuous monitoring using real-time optical scattering personal samplers to record particulate (PM10) concentrations at two internal locations. Very high episodes were observed in seating areas compared with the bar area. A photo-acoustic multi-gas analyser was used to record the gas phases (CO and CO2) at eight different locations throughout the bar and showed little spatial variation. This gave a clear indication of the problems associated with achieving acceptable Indoor Air Quality in a public space and identified a fundamental problem with the simplistic design approach taken to ventilate the space. Both gaseous and particulate concentrations within the bar were below maximum recommended levels although the time-series analysis illustrated the highly episodic nature of this exposure.

Propuesta para la creación de un bar tipo americano en la ciudad de Chiclayo

Trabajo de suficiencia profesional

Depositional conditions on an alluvial fan at the turn of the Weichselian to the Holocene – a case study in the Żmigród Basin, southwest Poland

Presented are the results of research into the fluvio-aeolian sedimentary succession at the site of Postolin in the Żmigród Basin, southwest Poland. Based on lithofacies analysis, textural analysis, Thermoluminescence and Infrared-Optical Stimulated Luminescence dating and GIS analysis, three lithofacies units were recognised and their stratigraphic suc- cession identified: 1) the lower unit was deposited during the Pleni-Weichselian within a sand-bed braided river fun- ctioning under permafrost conditions within the central part of the alluvial fan; 2) the middle unit is the result of aeolian deposition and fluvial redeposition on the surface of the fan during long-term permafrost and progressive decrease of humidity of the climate at the turn of the Pleni- to the Late Weichselian; 3) the upper unit accumulated following the development of longitudinal dunes at the turn of the Late Weichselian to the Holocene; the development of dunes was interrupted twice by the form being stabilised by vegetation and soil development.

International Conference of Hotel, Restaurant and Bar Workers.

Mode of access: Internet.

Influence Of Fluorescent Dye On Physical-mechanical Properties Of Luting Cements For Confocal Microscopy Analysis.

To evaluate the influence of a fluorescent dye (rhodamine B) on the physical and mechanical properties of three different luting cements: a conventional adhesive luting cement (RelyX ARC, 3M/ESPE), a self-adhesive luting cement (RelyX U-200, 3M/ESPE), and a self-etching and self-adhesive luting cement (SeT PP, SDI). The cements were mixed with 0.03 wt% rhodamine B, formed into bar-shaped specimens (n = 10), and light cured using an LED curing unit (Radii, SDI) with a radiant exposure of 32 J/cm(2) . The Knoop hardness (KHN), flexural strength (FS), and Young's modulus (YM) analyses were evaluated after storage for 24 h. Outcomes were subjected to two-way ANOVA and Tukey's test (P = 0.05) for multiple comparisons. No significant differences in FS or YM were observed among the tested groups (P ≥ 0.05); the addition of rhodamine B increased the hardness of the luting cements tested. The addition of a fluorescent agent at 0.03 wt% concentration does not negatively affect the physical-mechanical properties of the luting cement polymerization behavior.

Mechanical And Photoelastic Analysis Of Four Different Fixation Methods For Mandibular Body Fractures.

The aim of the present study was to compare four methods of fixation in mandibular body fractures. Mechanical and photoelastic tests were performed using polyurethane and photoelastic resin mandibles, respectively. The study groups contained the following: (I), two miniplates of 2.0 mm; (II) one 2.0 mm plate and an Erich arch bar; (III) one 2.4 mm plate and an Erich arch bar, and (IV) one 2.0 mm plate and one 2.4 mm plate. The differences between the mean values were analyzed using Tukey's test, the Mann-Whitney test and the Bonferroni correction. Group II recorded the lowest resistance, followed by groups I, IV and III. The photoelastic test confirmed the increase of tension in group II. The 2.4 mm system board in linear mandibular body fractures provided more resistance and the use of only one 2.0 mm plate in the central area of the mandible created higher tension.