Recuperação de metais de catalisadores mássicos e monometálicos

This work presents a study on the dissolution of some commercial monometallic and non-supported deactivated catalysts in HF + H2O2 mixtures (and, eventually, other media) under mild experimental conditions, after a previous oxidation step. The samples were neither crushed nor grinded. The best experimental conditions were dependent on the nature of the support and of the active phase. For example, the Pt/Al2O3 catalyst was dissolved in about 10 minutes, without agitation and heating; however, dissolution of the Pd/Al2O3, Ni/Al2O3, Ni/SiO2, Cu/Al2O3 and V2O5 samples required a temperature of 60 ºC and an agitation of 400 rpm. A careful addition of a NaOH solution allowed a quantitative precipitation of aluminium as criolite (Na3AlF6) or precipitation of Si as Na2SiF6; NaF was obtained as a by-product. As expected, processing of Pd/C, V2O5 and CuO.Cr2O3 samples was relatively simple. Metals recovery from catalysts reached a quantitative level in all samples studied; it is particularly interesting that platinum and palladium could be easily recovered in a single step process, thus separing them from aluminium.

Eletrodo íon-seletivo para determinação potenciométrica de alumínio(III) em meio de fluoreto

The construction and analytical evaluation of a coated graphite Al(III) ion-selective electrode, based on the ionic pair formed between the Al(F)n3-n anion and tricaprylylmethylammonium cation (Aliquat 336S) incorporated on a poly(vinylchloride) (PVC) matrix membrane are described. A thin membrane film of this ionic pair and dibutylphthalate (DBPh) in PVC was deposited directly on a cylindric graphite rod (2 cm length x 0.5 cm diameter) attached to the end of a glass tube using epoxy resin. The membrane solution was prepared by dissolving 40% (m/m) of PVC in 10 mL of tetrahydrofuran following addition of 45% (m/m) of DBPh and 15% (m/m) of the ionic pair. The effect of membrane composition, fluoride concentration, and several concomitants as potential interferences on the electrode response were investigated. The aluminium(III) ion-selective electrode showed a linear response ranging from 1.4 x 10-4 to 1.0 x 10-2 mol L-1, a detection limit of 4.0 x 10-5 mol L-1, aslope of -54.3±0.2mV dec-1 and a lifetime of more than 1 year (over 3000 determinations for each membrane). The slope indicates that the ion-selective electrode responds preferentially to the Al(F)4- species. Application of this electrode for the aluminium(III) determination in stomach anti-acid samples is reported.

Óxido misto de ítrio-alumínio dopado com Eu(III)

In this work, we report the synthesis and the photoluminescence features of Eu(III)-doped yttrium-aluminium oxide obtained by non-hydrolytic sol-gel routes. After heating the powders above 600 ºC the XRD patterns show the presence of the Y4Al2O9 (YAM) and Y3Al5O12 (YAG) phases. At 800 and at 1500 ºC the PL spectra display the Eu(III) lines characteristic of the YAM monoclinic phase. The 5D0->7F2 transition is favored relatively to the 5D0->7F1 lines. However, at 1100 ºC the cubic YAG is the preferential phase and the 5D0->7F1 transition dominates the spectrum. The Eu(III) ions lie in a centrosymmetrical site. The different solvents used in the sol-gel synthesis also change the relative proportion between these two phases. This is monitored analyzing the modifications in the relative intensity between the 5D0->7F2 and the 5D0->7F1 transitions.

Pilarização de uma argila brasileira com poliidroxications de alumínio: preparação, caracterização e propriedades catalíticas

Montmorillonite clay from Brazil was pillared with aluminium polyhydroxications. The influence of aging of the pillaring solution and the concentration of the clay suspension on the properties of the prepared materials was studied. The materials were characterized by chemical analysis, XRD and pore analysis by N2 adsorption. The catalytic properties were evaluated in the cumene cracking reaction. Results showed that the pillarization process increases the basal spaces of natural clay from 9.7 to 18.5 Å and the surface area from 41 to 300 m²/g.

Swarm Intelligent Selection and Optimization of Machining System Parameters for Microchannel Fabrication in Medical Devices

Current technology trends in medical device industry calls for fabrication of massive arrays of microfeatures such as microchannels on to nonsilicon material substrates with high accuracy, superior precision, and high throughput. Microchannels are typical features used in medical devices for medication dosing into the human body, analyzing DNA arrays or cell cultures. In this study, the capabilities of machining systems for micro-end milling have been evaluated by conducting experiments, regression modeling, and response surface methodology. In machining experiments by using micromilling, arrays of microchannels are fabricated on aluminium and titanium plates, and the feature size and accuracy (width and depth) and surface roughness are measured. Multicriteria decision making for material and process parameters selection for desired accuracy is investigated by using particle swarm optimization (PSO) method, which is an evolutionary computation method inspired by genetic algorithms (GA). Appropriate regression models are utilized within the PSO and optimum selection of micromilling parameters; microchannel feature accuracy and surface roughness are performed. An analysis for optimal micromachining parameters in decision variable space is also conducted. This study demonstrates the advantages of evolutionary computing algorithms in micromilling decision making and process optimization investigations and can be expanded to other applications

NMR in Crystals and Powders of Topazes with Different Colours

The present work is a part of the large project with purpose to investigate microstructure and electronic structure of natural topazes using NMR method. To reach this task we determined the relative contents of fluorine and hydrogen in crystals blue, colorless, wine and wine irradiated topazes. Then we determined the electric field gradients in site of aluminium atoms by NMR method, calculated EFG using ab initio method, and measured relaxation time dependence on heating temperature for blue, colorless, Swiss blue and sky blue topazes. Nuclear magnetic resonance (NMR) is an effective method to investigate the local structure in the crystal. The NMR study of the single crystal gives detailed information especially about the local crystal structure. As a result of this work we have received practical data, which is possible to use in future for making personal dosimetry and for preparation of mullite, which is widely used in traditional and advanced ceramic materials.

Kevyiden rakennemateriaalien soveltamismahdollisuudet metsäkoneissa

Asiakkaiden ympäristötietoisuus, metsäkoneille asetettavat korkeat vaatimukset ja kiristyvä kilpailu pakottavat metsäkoneiden valmistajat etsimään vaihtoehtoisia valmistusmateriaaleja, joita käyttämällä metsäkoneet kevenevät ja sitä kautta niiden ympäristökuormitukset ja käyttökustannukset alenevat ja kapasiteetti kasvaa. Metsäkoneiden rakenteiden keventämisessä alumiini on yksi varteenotettava vaihtoehto teräksen korvaajaksi, sillä alumiinin ominaisuus/paino -suhde on terästä parempi. Alumiinin käyttöä hitsatuissa rakenteissa ovat rajoittaneet sen korkea hinta ja melko huono väsymiskestävyys. Diplomityön tavoitteena on ollut selvittää mahdollisuuksia korvata metsäkoneiden rakenteista löytyviä teräksestä valmistettuja osia alumiinista valmistetuilla osilla. Diplomityön teoriaosassa on käsitelty rakenteiden keventämistä, metsäkoneille asetettavia vaatimuksia, alumiinien materiaaliominaisuuksia, alumiinirakenteiden valmistuksessa käytettäviä menetelmiä sekä alumiinirakenteiden suunnittelua. Lisäksi teoriaosassa on käsitelty komposiittien materiaaliominaisuuksia ja komposiittirakenteiden suunnittelua. Diplomityön kokeellisessa osassa on vertailtu nykyisiä rakennemateriaaleja ja alumiineja metsäkoneen eri osien rakennemateriaaleina osien vaatimusprofiileihin ja materiaalien ominaisuusprofiileihin perustuen. Vaatimusprofiilien perusteella on laadittu ominaisuusprofiilit alumiineille ja teräksille. Sovittamalla vaatimus- ja ominaisuusprofiilit yhteen arvoanalyysin avulla, metsäkoneista on etsitty mahdollisia kohteita, joissa nykyinen rakennemateriaali voitaisiin korvata alumiinilla. Tältä pohjalta metsäkoneista löytyi rakenteita, joissa alumiinin käyttö rakennemateriaalina teräksen sijaan olisi mahdollista. Diplomityö toimii hyvänä pohjana tutkittaessa mahdollisuuksia metsäkoneiden rakenteiden keventämiseksi.

Adsorção de glifosato sobre solos e minerais

Glyphosate, an enzyme inhibitor herbicide, has been widely used around the world in agriculture. Dr. John Franz from Monsanto Corporation (USA) discovered glyphosate in 1970. It has been showed that glyphosate is strongly adsorbed by inorganic soil components especially aluminium and iron oxides, and the phosphate group is involved in this interaction. The inactivation of glyphosate in soils can last for days or even months depending on soil characteristics. The addition of phosphate from fertilizers can displace glyphosate from the soils and this could be the cause of decreased productivity of some crops.

Preparação e caracterização de carvão ativado quimicamente a partir da casca de arroz

This work consists in a study about the chemical activation of charred rice hulls using NaOH as the activation agent. The influence of the naturally-occurring silica was particularly evidenced. X-ray diffraction patterns showed the formation of sodium carbonate and silicates in the activated samples, whereas thermogravimetric curves revealed a strong reduction in the ash content of these samples after washing with water. Nitrogen adsorption data indicated a microporosity development only in the washed samples, with BET surface area values of 450 and 1380 m²/g achieved for the samples activated at 800 °C starting from the precursor with or without silica, respectively.

Moottoripyörän rungon muuntelun valvontakriteerit muutoskatsastuksessa

Muutoskatsastusta koskeva lainsäädäntö aiheuttaa tulkintavaikeuksia ja rajoitteita moottoripyöräharrastajille ja alan toimijoille. Nykyinen asetus edellyttää tarvittaessa asiantuntijaselvitystä rakennemuutoksen lujuudesta ja hitsaustyöstä. Moottoripyörän geometria on laissa rajattu akselivälin ja emäputken kulman osalta. Moottoripyörien runkoja valmistetaan hitsaamalla seostamattomista teräksistä ja lämpökäsiteltävistä alumiini- ja terässeoksista. Runkojen muuntelu suoritetaan myös yleisesti hitsaamalla. Turvallisuuden kannalta tärkeiltä hitsausliitoksilta vaaditaan hyvää laatua, joka saavutetaan oikeilla hitsausparametreilla ja -suorituksella. Vaatimukset seostamattomalle teräkselle voidaan täyttää pätevöityneen hitsaajan toimesta. Lämpökäsiteltävät seokset vaativat lisäksi jälkilämpökäsittelyn, mikä edelleen vaikeuttaa runkojen hitsausta. Hitsien laadun merkitystä moottoripyörän rungossa tutkittiin soveltamalla rajoitetun vahingon periaatetta. Vauriotapauksena mallinnettiin satunnaisen rungon hitsausliitoksen murtuminen. Eri kuormitustilanteissa elementtimenetelmää hyödyntäen todettiin chopper-tyyppisten moottoripyörien runkojen olevan osittain vauriosietoisia ja havaittiin kriittiset hitsausliitokset emä- ja vaakaputken alueilla. Moottoripyörien runkojen kriittisiä hitsausliitoksia tarkasteltiin väsymisen kannalta. Soveltamalla tehollista lovijännitystä, vertailtiin emäputken hitsausliitosten väsymiskestävyyttä oletetulla kuormituksella. Tulosten perusteella muunneltu moottoripyörän runko voi olla alkuperäisrunkoa kestävämpi tai heikompi. Moottoripyörän akseliväli tai emäputken kulma eivät määrää kestävyyttä, vaan rakenteen yksityiskohtainen suunnittelu. Kriittisten liitosten väsymiskestävyyksissä havaittiin merkittäviä eroja eri mallien välillä.

A qualidade de água como indicador de uso e ocupação do solo: bacia do Gama - Distrito Federal

The spread of Brasília isn't accompanied by correct support of land occupation, situation that is reflected in water quality. Under the optics of land use and occupation, working with multivariate statistics as main tool, water physical and chemical quality of Gama Catchment were assessed. During two years samples were collected and analyzed for 24 parameters. The statistical analysis showed the influence of civil buildings, agricultural activities and the best statistical parameters to a quickly assessment: nitrate, ammonia, suspended solids and aluminium.

Estudio preliminar sobre la determinación de elementos traza en cervezas venezolanas por ICP-OES

The levels of several chemical elements were determined simultaneously in ten different beers of the Venezuelan market by ICP-OES. With the exception of chromium, beer does not provide important amounts of nutritional oligoelements. The average chromium content found (33 µg/L) is higher than one reported for USA's beer (10 µg/L) but smaller than another reported for Brazilian beer (66 µg/L). The average percentage of chromium RDA by beer consumption found for Venezuela (6.3%) is similar to that reported for Belgium (5%). Regarding toxic elements, one of the samples contained an elevated amount of aluminium, probably dissolved from the aluminium can.

L'Écho des mines et de la métallurgie

Variante(s) de titre : De 1895 à janv. 1899 paraît parallèlement à : "Aluminium (L'). Journal de l'électrolyse..." - Une éd. in 8° oblong a paru sous une couv. qui porte : "Anne (L') minière et métallurgique". - N'a pas paru d'août 1914 à juin 1916. - Pour le suppl. voir : "Documents miniers"

Tratamento do efluente do biodiesel utilizando a eletrocoagulação/flotação: investigação dos parâmetros operacionais

Electrocoagulation/flotation process was applied to treat biodiesel wastewater using aluminium electrodes. Firstly, a literature survey was conducted to choose the process variables and then, operational parameters including initial pH, electrode distance and reaction time were tested. Experimental results showed the best parameter that can be used in a factorial design for further studies. The results indicate that electrocoagulation/flotation is very efficient to reduce oil and grease, the effluent was very clear after treatment and small amount of sludge was produced.