Resonance Raman and DFT studies of tetra-tert-butyl porphine: Assignment of strongly enhanced distortion modes in a ruffled porphyrin

The free-base form of tetra-tert-butyl porphine (TtBP), which has extremely bulky meso substituents, is severely distorted from planarity, with a ruffling angle of 65.5degrees. The resonance Raman spectrum of TtBP (lambda(ex) = 457.9 nm) and its d(2), d(8), and d(10) isotopomers have been recorded, and while the spectra show high-frequency bands similar to those observed for planar meso-substituted porphyrins, there are several additional intense bands in the low-frequency region. Density functional calculations at the B3-LYP/6-31G(d) level were carried out for all four isotopomers, and calculated frequencies were scaled using a single factor of 0.98. The single factor scaling approach was validated on free base porphine where the RMS error was found to be 14.9 cm(-1). All the assigned bands in the high-frequency (> 1000 cm(-1)) region of TtBP were found to be due to vibrations similar in character to the in-plane skeletal modes of conventional planar porphyrins. In the low-frequency region, two of the bands, assigned as nu(8) (ca. 330 cm(-1)) and nu(16) (ca. 540 cm(-1)), are also found in planar porphyrins such as tetra-phenyl porphine (TPP) and tetra-iso-propyl porphine (IPP). Of the remaining three very strong bands, the lowest frequency band was assigned as gamma(12) (pyr swivel, obsd 415 cm(-1), calcd 407 cm(-1) in do). The next band, observed at 589 cm-1 in the do compound (calcd 583 cm(-1)), was assigned as a mode whose composition is a mixture of modes that were previously labeled gamma(13) (gamma(CmCaHmCa)) andy gamma(11) (pyr fold(asym)) in NiOEP. The final strong band, observed at 744 cm(-1) (calcd 746 cm(-1)), was assigned to a mode whose composition is again a mixture of gamma(11) and gamma(13), although here it is gamma(11) rather than gamma(13) which predominates. These bands have characters and positions similar to those of three of the four porphyrin ring-based, weak bands that have previously been observed for NiTPP. In addition there are several weaker bands in the TtBP spectra that are also

Interaction of directional, neuromuscular and egocentric constraints on the stability of preferred bimanual coordination patterns

We investigated how the relative direction of limb movements in external space (iso- and non-isodirectionality), muscular constraints (the relative timing of homologous muscle activation) and the egocentric frame of reference (moving simultaneously toward/away the longitudinal axis of the body) contribute to the stability of coordinated movements. In the first experiment, we attempted to determine the respective stability of isodirectional and non-isodirectional movements in between-persons coordination. In a second experiment, we determined the effect of the relative direction in external space, and of muscular constraints, on pattern stability during a within-person bimanual coordination task. In the third experiment we dissociated the effects on pattern stability of the muscular constraints, relative direction and egocentric frame of reference. The results showed that (1) simultaneous activation of homologous muscles resulted in more stable performance than simultaneous activation of non-homologous muscles during within-subject coordination, and that (2) isodirectional movements were more stable than non-isodirectional movements during between-persons coordination, confirming the role of the relative direction of the moving limbs in the stability of bimanual coordination. Moreover, the egocentric constraint was to some extent found distinguishable from the effect of the relative direction of the moving limbs in external space, and from the effect of the relative timing of muscle activation. In summary, the present study showed that relative direction of the moving limbs in external space and muscular constraints may interact either to stabilize or destabilize coordination patterns. (C) 2003 Published by Elsevier B.V.

Pyrrolidinium Ionic Liquid Crystals

N-Alkyl-N-methylpyrrolidinium cations have been used for the design of ionic liquid crystals, including a new type of uranium-containing metallomesogen. Pyrrolidinium salts with bromide, bis(trifluoromethylsulfonyl)-imide, tetrafluoroborate, hexafluorophosphate, thiocyanate, tetrakis(2-thenoyltrifluoroacetonato)europate(III) and tetrabromouranyl] counteranions were prepared. For the bromide salts and tetrabromouranyl compounds, the chain length of the alkyl group CnH2n+1 was varied from eight to twenty carbon atoms (n =8. 10-20). The compounds show rich mesomorphic behaviour: highly ordered smectic phases (the crystal smectic E phase and the uncommon crystal smectic T phase), smectic A phases, and hexagonal. columnar phases were observed, depending on chain length and anion. This work gives better insight into the nature and formation of the crystal smectic T phase, and the Molecular requirements for the appearance of this highly ordered phase. This uncommon tetragonal mesophase is thoroughly discussed on the basis of detailed powder X-ray diffraction experiments and in relation to the existing literature. Structural models are proposed for self-assembly of the molecules within the smectic layers. In addition, the photophysical properties of the compounds containing a metal complex anion were investigated. For the uranium-containing mesogens, luminescence can be induced by dissolving them in an ionic: liquid matrix. The europium-containing compound shows intense red photoluminescence with high colour Purity.

Real time monitoring of the polymerisation of PMMA bone cement using Raman spectroscopy

In this investigation Raman spectroscopy was shown to be a method that could be used to monitor the polymerisation of PMMA bone cement. Presently there is no objective method that orthopaedic surgeons can use to quantify the curing process of cement during surgery. Raman spectroscopy is a non-invasive, non-destructive technique that could offer such an option. Two commercially available bone cements (Palacos® R and SmartSet® HV) and different storage conditions (4 and 22°C) were used to validate the technique. Raman spectroscopy was found to be repeatable across all conditions with the completion of the polymerisation process particularly easy to establish. All tests were benchmarked against current temperature monitoring methods outlined in ISO and ASTM standards. There was found to be close agreement with the standard methods and the Raman spectroscopy used in this study.

SRIF receptor subtype expression and involvement in positive and negative contractile effects of somatostatin-14 (SRIF-14) in ventricular cardiomyocytes.

Background/Aims: Somatostatin-14 (SRIF-14), a neuropeptide co-stored with acetylcholine in the cardiac parasympathetic innervation, exerts both positive and negative influences directly on contraction of ventricular cardiomyocytes, indicative of involvement of more than one of five known SRIF (SSTR) receptor subtypes. The aim was to characterize receptor subtype expression in adult rat ventricular cardiomyocytes and to investigate the influence of a series of SRIF (SSTR) subtype-selective agonists on contractile parameters. Methods: mRNA and protein expression of each receptor subtype were quantified by RT-PCR and immunoblotting respectively; for contraction studies, cells were stimulated at 0.5 Hz under basal conditions and in the presence of isoprenaline (ISO, 10-8M). Results: all five SRIF (SSTR) receptor subtypes were expressed in cardiomyocytes although SRIF1A (SSTR2) and SRIF2A (SSTR1) were less abundant than the other subtypes. L803087 (10-8M), a SRIF2B (SSTR4) agonist, attenuated ISO-stimulated peak contractile amplitude and prolonged relaxation time (T50). L796778 (10-7M), a SRIF1C (SSTR3) agonist, augmented basal and ISO-stimulated peak contractile amplitude; L779976 (10-8M) and L817818 (10-9M), agonists at SRIF1A (SSTR2) and SRIF1B (SSTR5) receptors, respectively, also augmented ISO-stimulated peak amplitude. Conclusion: these data support involvement of SRIF2B (SSTR4) receptors in the negative contractile effects of SRIF-14, while one or more of the three SRIF1 receptor subtypes (SSTR2, 3 or 5) may contribute to the positive contractile effects of SRIF-14.

Palladium-mediated reductive coupling, a stereoselective approach to the 8-dehydropumiliotoxin skeleton

Reductive cyclisation of ail E-vinyl bromide with ail allylic acetate proceeds under palladium catalysis 10 give the 8-dehydropumiliotoxin skeleton, a potential advanced precursor to 8-deoxypumiliotoxin alkaloids. Control of the stereochemistry of the E-vinyl bromide precursor is achieved readily using the Kogen or Bruckner bromophosphonate reagents and the reductive cyclisation proceeds with retention of the vinyl bromide stereochemistry. The mechanism for the cyclisation involves an in situ conversion of the allylic acetate to ail allyl stannane followed by ail intramolecular Stille-type coupling.

Expedient synthesis of (+)-trans-5-allylhexahydroindolizidin-3-one

Treatment of the bicyclic iminium ion derived from 5-methoxyhexahydroindolizidin-3-one with allyltrimethylsilane gave exclusively the diastereoisomer in which the allyl group was axial. This substrate is a useful precursor to 5-propyl-3-alkylindolizidine alkaloids. (C) 1999 Elsevier Science Ltd. All rights reserved.

Steady-State and Transient Performance of Biodiesel-Fueled Compression-Ignition-Based Electrical Generation

This paper investigates the performance characteristics of rapeseed methyl ester, EN 14214 biodiesel, when used for electrical generation in compression ignition engines. The work was inspired by the need to replace fossil diesel fuel with a sustainable low carbon alternative while maintaining generator performance, power quality, and compliance with ISO 8528-5. A 50-kVA Perkins diesel engine generator was used to assess the impact of biodiesel with particular regard to gen-set fuel consumption, load acceptance, and associated standards. Tests were performed on the diesel gen-set for islanded and grid-connected modes of operation, hence both steady-state and transient performance were fully explored. Performance comparisons were made with conventional fossil diesel fuel, revealing minimal technical barriers for electrical generation from this sustainable, carbon benign fuel. Recommendations for improved transient performance are proposed and validated through tests.

Synthesis of the alkaloids hopromine, hoprominol and hopromalinol, using transamidation methods.

Synthesis of the unsym. Homalium alkaloids hopromine (I, R = H, R1 = pentyl), hoprominol (I, R = OH, R1 = pentyl) and hopramalinol (I, R = OH, R1 = Ph), in diastereoisomeric mixt. form, is reported. The component eight-membered azalactams are first prepd. N-(3-halogenopropyl)-4-pentyl- and 4-heptylazetidin-2-ones are aminated and ring expanded in liq. ammonia to give, after reductive methylation, the corresponding 4-alkyl-5-methyl-1,5-diazacyclooctan-2-ones. Synthesis of the 4-(2-hydroxyheptyl)-5-methyl-1,5-diazacyclooctan-2-one required for hoprominol and hopromalinol is carried out via 4-allyl ?-lactam ring expansion to the eight-membered 4-allylazalactam, followed by methylation, epoxidn. and epoxide opening with lithium dibutylcuprate. A similar epoxidn.-cuprate sequence was carried out on the epoxypropyl ?-lactam, as its N-tert-butyldimethylsilyl deriv., and led to a convenient copper-catalyzed N- to O-migration of the protection; this migration is examd. Alkylation gave O-tert-butyldimethylsilyl-protected N-(3-chloropropyl)-4-(2-hydroxyheptyl)azetidin-2-one which could be aminated and transamidated in excellent yield, to give, after methylation, a superior sequence to the required eight-membered hydroxy azalactam. Although satisfactory for attachment of the first azalactam unit, a dibromobutane coupling system proved unreactive for the second. Couplings with unmethylated, methylated, and benzyloxycabronyl-protected azalactams were examd. using (E)-1,4-dibromobutene and (Z)-1,4-dichlorobutene as the bridging unit. Employing the latter, coupling the first N-methylated azalactam with potassium bis(trimethylsilyl)amide as the base, and then the second with bis(trimethylsilyl)amide-sodium hydride as the base system, provided a satisfactory synthetic outcome. Hydrogenation under acidic conditions gave the unsym. structures hopromine, hoprominol and hopromalinol, as well as the more simple and sym. alkaloid, homaline.

A new approach to peptide synthesis

A new approach to the synthesis of dipeptides is described based on the formation of the CONH-CHRCO bond by carbenoid N-H insertion, rather than the formation of the peptide bond itself. The key N-H insertion reaction was carried out by treating a mixt. of N-protected amino acid amide and tri-Et diazophosphonoacetate, EtO2CC(:N2)PO(OEt)2, with a catalytic amt. of Rh2(OAc)4 in toluene to form phosphonates, e.g. I (R1 = H, Me, iso-Pr, iso-Bu; R2 = PhCH2O2C, Me3CO2C) in good yield. Dehydro dipeptides, e.g. II (R1, R2 = same as above; R3 = Ph, iso-Pr, N-Boc-indol-3-yl) were prepd. by Wadsworth-Emmons reaction of the phosphonates I with R3CHO using DBU as base.

Study of the transamidative ring expansion of N--halogenoalkyl--lactams of alkyl chain lengths 2–12 in liquid ammonia and other liquid amines: syntheses of 7-, 8- and 9-membered 1,5-diaza cyclic ketones, including routes to (±)-dihydroperiphylline and (±)-celabenzine

N-(3-Halogenopropyl)-4-phenylazetidin-2-ones undergo amination in liquid ammonia followed by transamidative ring expansion to give the eight-membered 4-phenyl -1,5-diazacyclooctan-2-one in excellent yield. Ring expansion of the amines in liquid ammonia is found to be much more effective than in hydrocarbon solvents. Formation of 7-, 8-, and 9-membered azalactams from the requisite -halogenoalkyl--lactams is an excellent synthetic process, though it is not applicable to 10membered rings. In the cases of rings of 13-, 15- and 17-members, although amination and apparent expansion takes place, the large rings appear not to be stable to ammonia and the final products are acyclic amides. N-[4-Halogenobut-2(Z)-enyl]-4-phenylazetidin-2-one satisfactorily forms a 9-membered (Z)-olefinic azalactam, but the (E)-isomer gives an acyclic amino amide. By using alkyl-substituted -lactam side-chains, C-substituted medium rings can be obtained; the relative instability of N-acyl -lactams to ammonia, however, leads to acylamino amides rather than expanded rings.Employing ethylamine in place of ammonia, it is shown that N-ethylated azalactams are formed satisfactorily, and using allylamine, N-allyl medium rings capable of further elaboration are obtained. The chemistry of these systems is discussed. Using transamidation in liquid ammonia, a short synthesis of the 9-membered spermidine alkaloid (±)-dihydroperiphylline is reported. Synthesis of key intermediates, whose transformation into the 13-membered alkaloids of the celabenzine group has already been effected, has been carried out.X-Ray single-crystal structure determinations for 4-phenyl-1,5-diazacyclononan-2-one, trans-4-phenyl-8-methyl-1,5-diazacyclooctan-2-one and (Z)-4-phenyl-1,5-diazacyclonon-7-en-2-one are reported, and comment is made on certain conformational features.

Effect of MWCNT addition on the thermal and rheological properties of polymethyl methacrylate bone cement

Multi-walled carbon nanotube (MWCNT)/polymethyl methacrylate (PMMA) composites with loadings ranging from 0.1 to 1.0 wt.% were prepared for use as bone cement. Unfunctionalised, carboxyl and amine functionalised MWCNT were used. Thermal properties were characterised in accordance with the International Standard for acrylic cements, ISO 5833:2002. The rate of reaction exotherm generated and thermal necrosis index (TNI) values were calculated. Polymerisation kinetics were characterised using parallel plate rheology and the exotherm during polymerisation was reduced by ˜4–34%, as a consequence of the MWCNT thermal conductivity. The rate of reaction was significantly altered, such that the setting times of the cements were extended (˜3–24%). Consequently, significant decreases in TNI values (ranging from 3% to 99%) were recorded, which could reduce the exothermic temperatures experienced in vivo and therefore prevent the likelihood of polymerising PMMA cement causing thermally-induced bone tissue necrosis. Thermal data was supported by the rheological characterisation results. Onset of polymerisation for PMMA cement exhibited a strong linear increase as a function of MWCNT loading, however, polymer gelation was not affected to the same degree. It is proposed that the chemically functionalised MWCNT altered PMMA bone cement polymerisation kinetics, reducing the rate of polymerisation, and hence, the reaction exotherm.

A search for interstellar gas-phase CO2 gas: Solid state abundance ratios

We present searches for gas-phase CO2 features in the ISO-SWS infrared spectra of four deeply embedded massive young stars, which all show strong solid CO2 absorption. The abundance of gas-phase CO2 is at most 2. 10(-7) with respect to H-2, and is less than 5% of that in the solid phase. This is in strong contrast to CO, which is a factor of 10-100 more abundant in the gas than in solid form in these objects. The gas/solid state ratios of CO2, CO and H2O are discussed in terms of the physical and chemical state of the clouds.

Delineation of a quick clay zone at Smørgrav, Norway, with electromagnetic methods under geotechnical constraints

In many coastal areas of North America and Scandinavia, post-glacial clay sediments have emerged above sea level due to iso-static uplift. These clays are often destabilised by fresh water leaching and transformed to so-called quick clays as at the investigated area at Smørgrav, Norway. Slight mechanical disturbances of these materials may trigger landslides. Since the leaching increases the electrical resistivity of quick clay as compared to normal marine clay, the application of electromagnetic (EM) methods is of particular interest in the study of quick clay structures.

For the first time, single and joint inversions of direct-current resistivity (DCR), radiomagnetotelluric (RMT) and controlled-source audiomagnetotelluric (CSAMT) data were applied to delineate a zone of quick clay. The resulting 2-D models of electrical resistivity correlate excellently with previously published data from a ground conductivity metre and resistivity logs from two resistivity cone penetration tests (RCPT) into marine clay and quick clay. The RCPT log into the central part of the quick clay identifies the electrical resistivity of the quick clay structure to lie between 10 and 80 O m. In combination with the 2-D inversion models, it becomes possible to delineate the vertical and horizontal extent of the quick clay zone. As compared to the inversions of single data sets, the joint inversion model exhibits sharper resistivity contrasts and its resistivity values are more characteristic of the expected geology. In our preferred joint inversion model, there is a clear demarcation between dry soil, marine clay, quick clay and bedrock, which consists of alum shale and limestone.

NaH Mediated Isomerisation-Allylation Reaction of 1,3-Substituted Propenols

A base mediated isomerisation-allylation protocol of 1,3- disubstituted propenols has been established. The use of diaryl and aryl-silyl substrates is reported alongside the use of substituted allyl bromides. Mechanistic experiments have also been conducted to elucidate the reaction pathway.