Modeling, optimizing and simulating robot calibration with accuracy improvement

This work describes techniques for modeling, optimizing and simulating calibration processes of robots using off-line programming. The identification of geometric parameters of the nominal kinematic model is optimized using techniques of numerical optimization of the mathematical model. The simulation of the actual robot and the measurement system is achieved by introducing random errors representing their physical behavior and its statistical repeatability. An evaluation of the corrected nominal kinematic model brings about a clear perception of the influence of distinct variables involved in the process for a suitable planning, and indicates a considerable accuracy improvement when the optimized model is compared to the non-optimized one.

Experimental validation of a 3-D vision-based measurement system applied to robot calibration

One of the problems that slows the development of off-line programming is the low static and dynamic positioning accuracy of robots. Robot calibration improves the positioning accuracy and can also be used as a diagnostic tool in robot production and maintenance. A large number of robot measurement systems are now available commercially. Yet, there is a dearth of systems that are portable, accurate and low cost. In this work a measurement system that can fill this gap in local calibration is presented. The measurement system consists of a single CCD camera mounted on the robot tool flange with a wide angle lens, and uses space resection models to measure the end-effector pose relative to a world coordinate system, considering radial distortions. Scale factors and image center are obtained with innovative techniques, making use of a multiview approach. The target plate consists of a grid of white dots impressed on a black photographic paper, and mounted on the sides of a 90-degree angle plate. Results show that the achieved average accuracy varies from 0.2mm to 0.4mm, at distances from the target from 600mm to 1000mm respectively, with different camera orientations.

Experimental study applied to an industrial robot by using variable structure controllers and friction compensation

Control of an industrial robot is mainly a problem of dynamics. It includes non-linearities, uncertainties and external perturbations that should be considered in the design of control laws. In this work, two control strategies based on variable structure controllers (VSC) and a PD control algorithm are compared in relation to the tracking errors considering friction. The controller's performances are evaluated by adding an static friction model. Simulations and experimental results show it is possible to diminish tracking errors by using a model based friction compensation scheme. A SCARA robot is used to illustrate the conclusions of this paper.

Mobile clinics in public health care: Integrated service offerings for rural elderly

This research is an analysis of the value and content of local service offerings that enable longer periods of living at home for elderly people. Mobile health care and new distribution services have provided an interesting solution in this context. The research aim to shed light on the research question, ‘How do we bundle services based on different customer needs?’ A research process consisting of three main phases was applied for this purpose. During this process, elderly customers were segmented, the importance of services was rated and service offerings were defined. Value creation and service offering provides theoretical framework for the research. The target group is South Karelia’s 60 to 90-year old individuals and the data has been acquired via a postal questionnaire. Research has been conducted as exploratory research utilizing the methods of quantitative and social network analysis. The main results of the report are identified customer segments and service packages that fits to the segments’ needs. The results indicate the needs of customers and the results are additionally analysed from the producer’s point of view. In addition to the empirical results, the used theory framework has been developed further in order for the service-related theories to be seen from the customer’s point of view and not just from the producer’s point of view.

[Aaria La donna e mobile oopperasta Rigoletto]

Soitinnus: lauluääni (tenori), orkesteri.

Features for mobile applications popularity

Mobile applications market shows one of the highest growth rates for the market of intellectual products. The market is attractive to investors, despite the fact that the major companies of this industry already firmly consolidated its position. Experts predict the growth of the market for mobile applications with the development of mobile technologies in general. To demonstrate the explosive growth of the market and the scale of its impact, it is worth recalling the mobile game Angry Birds, which was able to achieve a huge reach and formed a full-fledged media brand, comparable to the film industry brands. The reasons why some games become popular and others not, are important for understanding the driving factors of the games industry. The Master’s Thesis explores the factors for mobile games applications popularity and ranking and propose recommendations for mobile games app store optimization of app representation. It discovers particular features of mobile games applications and releases’ influence on their popularity. Also the study assumes usage of such business models as The Business Model Canvas by Osterwalder and The Lean Startup Methodology by Ries, and describes the best practices of mobile application development process and market positioning. Moreover, the Master’s Thesis gives examples of multiple case studies about successful mobile apps developers.

Energy and Dynamics of the solar agricultural robot "SolarSprayer"

The main objective of the present study was to design an agricultural robot, which work is based on the generation of the electricity by the solar panel. To achieve the proper operation of the robot according to the assumed working cycle the detailed design of the main equipment was made. By analysing the possible areas of implementation together with developments, the economic forecast was held. As a result a decision about possibility of such device working in agricultural sector was made and the probable topics of the further study were found out.

Bridging the digital divide in developing countries: The role of mobile technology in bridging the digital divide

This thesis investigates how mobile technology usage could help to bring Information and communication technologies (ICT) to the people in developing countries. Some people in developing countries have access to use ICT while other people do not have such opportunity. This digital divide among people is present in many developing countries where computers and the Internet are difficult to access. The Internet provides information that can increase productivity and enable markets to function more efficiently. The Internet reduces information travel time and provides more efficient ways for firms and workers to operate. ICT and the Internet can provide opportunities for economic growth and productivity in developing countries. This indicates that it is very important to bridge the digital divide and increase Internet connections in developing countries. The purpose of this thesis is to investigate how can mobile technology and mobile services help to bridge the digital divide in developing countries. Theoretical background of this thesis consists of a collection of articles and reports. Theoretical material was gathered by going through literature on the digital divide, mobile technology and mobile application development. The empirical research was conducted by sending a questionnaire by email to a selection of application developers located in developing countries. The questionnaire’s purpose was to gather qualitative information concerning mobile application development in developing countries. This thesis main result suggests that mobile phones and mobile technology usage can help to bridge the digital divide in developing countries. This study finds that mobile technology provides one of the best tools that can help to bridge the digital divide in developing countries. Mobile technology can bring affordable ICT to people who do not have access to use computers. Smartphones can provide Internet connection, mobile services and mobile applications to a rapidly growing number of mobile phone users in developing countries. New low-cost smartphones empower people in developing countries to have access to information through the Internet. Mobile technology has the potential to help to bridge the digital divide in developing countries where a vast amount of people own mobile phones.

Dual light barrier method for six degrees of freedom tool center point calibration of an industrial robot

Tool center point calibration is a known problem in industrial robotics. The major focus of academic research is to enhance the accuracy and repeatability of next generation robots. However, operators of currently available robots are working within the limits of the robot´s repeatability and require calibration methods suitable for these basic applications. This study was conducted in association with Stresstech Oy, which provides solutions for manufacturing quality control. Their sensor, based on the Barkhausen noise effect, requires accurate positioning. The accuracy requirement admits a tool center point calibration problem if measurements are executed with an industrial robot. Multiple possibilities are available in the market for automatic tool center point calibration. Manufacturers provide customized calibrators to most robot types and tools. With the handmade sensors and multiple robot types that Stresstech uses, this would require great deal of labor. This thesis introduces a calibration method that is suitable for all robots which have two digital input ports free. It functions with the traditional method of using a light barrier to detect the tool in the robot coordinate system. However, this method utilizes two parallel light barriers to simultaneously measure and detect the center axis of the tool. Rotations about two axes are defined with the center axis. The last rotation about the Z-axis is calculated for tools that have different width of X- and Y-axes. The results indicate that this method is suitable for calibrating the geometric tool center point of a Barkhausen noise sensor. In the repeatability tests, a standard deviation inside robot repeatability was acquired. The Barkhausen noise signal was also evaluated after recalibration and the results indicate correct calibration. However, future studies should be conducted using a more accurate manipulator, since the method employs the robot itself as a measuring device.

Development of agnostic mobile applications with cross-platform cloud computing platforms

Smart phones became part and parcel of our life, where mobility provides a freedom of not being bounded by time and space. In addition, number of smartphones produced each year is skyrocketing. However, this also created discrepancies or fragmentation among devices and OSes, which in turn made an exceeding hard for developers to deliver hundreds of similar featured applications with various versions for the market consumption. This thesis is an attempt to investigate whether cloud based mobile development platforms can mitigate and eventually eliminate fragmentation challenges. During this research, we have selected and analyzed the most popular cloud based development platforms and tested integrated cloud features. This research showed that cloud based mobile development platforms may able to reduce mobile fragmentation and enable to utilize single codebase to deliver a mobile application for different platforms.

Stiffness based trajectory planning and feedforward based vibration suppression control of parallel robot machines

The dissertation proposes two control strategies, which include the trajectory planning and vibration suppression, for a kinematic redundant serial-parallel robot machine, with the aim of attaining the satisfactory machining performance. For a given prescribed trajectory of the robot's end-effector in the Cartesian space, a set of trajectories in the robot's joint space are generated based on the best stiffness performance of the robot along the prescribed trajectory. To construct the required system-wide analytical stiffness model for the serial-parallel robot machine, a variant of the virtual joint method (VJM) is proposed in the dissertation. The modified method is an evolution of Gosselin's lumped model that can account for the deformations of a flexible link in more directions. The effectiveness of this VJM variant is validated by comparing the computed stiffness results of a flexible link with the those of a matrix structural analysis (MSA) method. The comparison shows that the numerical results from both methods on an individual flexible beam are almost identical, which, in some sense, provides mutual validation. The most prominent advantage of the presented VJM variant compared with the MSA method is that it can be applied in a flexible structure system with complicated kinematics formed in terms of flexible serial links and joints. Moreover, by combining the VJM variant and the virtual work principle, a systemwide analytical stiffness model can be easily obtained for mechanisms with both serial kinematics and parallel kinematics. In the dissertation, a system-wide stiffness model of a kinematic redundant serial-parallel robot machine is constructed based on integration of the VJM variant and the virtual work principle. Numerical results of its stiffness performance are reported. For a kinematic redundant robot, to generate a set of feasible joints' trajectories for a prescribed trajectory of its end-effector, its system-wide stiffness performance is taken as the constraint in the joints trajectory planning in the dissertation. For a prescribed location of the end-effector, the robot permits an infinite number of inverse solutions, which consequently yields infinite kinds of stiffness performance. Therefore, a differential evolution (DE) algorithm in which the positions of redundant joints in the kinematics are taken as input variables was employed to search for the best stiffness performance of the robot. Numerical results of the generated joint trajectories are given for a kinematic redundant serial-parallel robot machine, IWR (Intersector Welding/Cutting Robot), when a particular trajectory of its end-effector has been prescribed. The numerical results show that the joint trajectories generated based on the stiffness optimization are feasible for realization in the control system since they are acceptably smooth. The results imply that the stiffness performance of the robot machine deviates smoothly with respect to the kinematic configuration in the adjacent domain of its best stiffness performance. To suppress the vibration of the robot machine due to varying cutting force during the machining process, this dissertation proposed a feedforward control strategy, which is constructed based on the derived inverse dynamics model of target system. The effectiveness of applying such a feedforward control in the vibration suppression has been validated in a parallel manipulator in the software environment. The experimental study of such a feedforward control has also been included in the dissertation. The difficulties of modelling the actual system due to the unknown components in its dynamics is noticed. As a solution, a back propagation (BP) neural network is proposed for identification of the unknown components of the dynamics model of the target system. To train such a BP neural network, a modified Levenberg-Marquardt algorithm that can utilize an experimental input-output data set of the entire dynamic system is introduced in the dissertation. Validation of the BP neural network and the modified Levenberg- Marquardt algorithm is done, respectively, by a sinusoidal output approximation, a second order system parameters estimation, and a friction model estimation of a parallel manipulator, which represent three different application aspects of this method.

Letters from the War of Ecosystems – An Analysis of Independent Software Vendors in Mobile Application Marketplaces

The recent emergence of a new generation of mobile application marketplaces has changed the business in the mobile ecosystems. The marketplaces have gathered over a million applications by hundreds of thousands of application developers and publishers. Thus, software ecosystems—consisting of developers, consumers and the orchestrator—have emerged as a part of the mobile ecosystem. This dissertation addresses the new challenges faced by mobile application developers in the new ecosystems through empirical methods. By using the theories of two-sided markets and business ecosystems as the basis, the thesis assesses monetization and value creation in the market as well as the impact of electronic Word-of-Mouth (eWOM) and developer multihoming— i. e. contributing for more than one platform—in the ecosystems. The data for the study was collected with web crawling from the three biggest marketplaces: Apple App Store, Google Play and Windows Phone Store. The dissertation consists of six individual articles. The results of the studies show a gap in monetization among the studied applications, while a majority of applications are produced by small or micro-enterprises. The study finds only weak support for the impact of eWOM on the sales of an application in the studied ecosystem. Finally, the study reveals a clear difference in the multi-homing rates between the top application developers and the rest. This has, as discussed in the thesis, an impact on the future market analyses—it seems that the smart device market can sustain several parallel application marketplaces.

Mobile Banking and Mobile Payments: Changing Banking Services in Finland

The purpose of this thesis is to examine how mobile banking and mobile payments services will change the banking sector in Finland, and what role non-bank companies from the IT and telecom industries will play in this process. The thesis consists of a literature review and a qualitative study. The literature review forms a comprehensive overview of mobile banking and mobile payments services. The qualitative research was conducted as a descriptive study, focusing on the views of bank and non-bank players. The results show that banks have a significant advantage over their IT and telecom rivals in regards to their service offering, financial buffer, and status as trustworthy institutions. The banks’ embrace of mobile financial services will change the Finnish banking sector into one, with a light branch network focused on sales power, and a heavy emphasis on new mobile devices providing service power regardless of time and place.

Development of Generic Simulation Model for Mobile Working Machines

This master’s thesis has been done for Drive! –project in which a new electric motor solution for mobile working machines is developed. Generic simulation model will be used as marketing and development tool. It can be used to model a wide variety of different vehicles with and without electric motor and to show customer the difference between traditionally build vehicles and those with new electric motor solution. Customers can also use simulation model to research different solutions for their own vehicles. At the start of the project it was decided that MeVEA software would be used as main simulation program and Simulink will only be used to simulate the operation of electrical components. Development of the generic model started with the research of these two software applications, simulation models which are made with them and how these simulation models can be build faster. Best results were used for building of generic simulation model. Finished generic model can be used to produce new tractor models for real-time simulations in short notice. All information about model is collected to one datasheet which can be easily filled by the user. After datasheet is filled a script will automatically build new simulation model in seconds. At the moment generic model is capable of building simulation models for wide variety of different tractors but it can be easily altered for other vehicle types too which would also benefit greatly from electric drive solution. Those could be for example wheel loaders and harvesters.

Novel virtual environment and real-time simulation based methods for improving life-cycle efficiency of non-road mobile machinery

Virtual environments and real-time simulators (VERS) are becoming more and more important tools in research and development (R&D) process of non-road mobile machinery (NRMM). The virtual prototyping techniques enable faster and more cost-efficient development of machines compared to use of real life prototypes. High energy efficiency has become an important topic in the world of NRMM because of environmental and economic demands. The objective of this thesis is to develop VERS based methods for research and development of NRMM. A process using VERS for assessing effects of human operators on the life-cycle efficiency of NRMM was developed. Human in the loop simulations are ran using an underground mining loader to study the developed process. The simulations were ran in the virtual environment of the Laboratory of Intelligent Machines of Lappeenranta University of Technology. A physically adequate real-time simulation model of NRMM was shown to be reliable and cost effective in testing of hardware components by the means of hardware-in-the-loop (HIL) simulations. A control interface connecting integrated electro-hydraulic energy converter (IEHEC) with virtual simulation model of log crane was developed. IEHEC consists of a hydraulic pump-motor and an integrated electrical permanent magnet synchronous motorgenerator. The results show that state of the art real-time NRMM simulators are capable to solve factors related to energy consumption and productivity of the NRMM. A significant variation between the test drivers is found. The results show that VERS can be used for assessing human effects on the life-cycle efficiency of NRMM. HIL simulation responses compared to that achieved with conventional simulation method demonstrate the advances and drawbacks of various possible interfaces between the simulator and hardware part of the system under study. Novel ideas for arranging the interface are successfully tested and compared with the more traditional one. The proposed process for assessing the effects of operators on the life-cycle efficiency will be applied for wider group of operators in the future. Driving styles of the operators can be analysed statistically from sufficient large result data. The statistical analysis can find the most life-cycle efficient driving style for the specific environment and machinery. The proposed control interface for HIL simulation need to be further studied. The robustness and the adaptation of the interface in different situations must be verified. The future work will also include studying the suitability of the IEHEC for different working machines using the proposed HIL simulation method.