Microclimate and gas emissions in dairy buildings : Instrumentation, theory and measurements

The aim of this thesis was to develop measurement techniques and systems for measuring air quality and to provide information about air quality conditions and the amount of gaseous emissions from semi-insulated and uninsulated dairy buildings in Finland and Estonia. Specialization and intensification in livestock farming, such as in dairy production, is usually accompanied by an increase in concentrated environmental emissions. In addition to high moisture, the presence of dust and corrosive gases, and widely varying gas concentrations in dairy buildings, Finland and Estonia experience winter temperatures reaching below -40 ºC and summer temperatures above +30 ºC. The adaptation of new technologies for long-term air quality monitoring and measurement remains relatively uncommon in dairy buildings because the construction and maintenance of accurate monitoring systems for long-term use are too expensive for the average dairy farmer to afford. Though the documentation of accurate air quality measurement systems intended mainly for research purposes have been made in the past, standardised methods and the documentation of affordable systems and simple methods for performing air quality and emissions measurements in dairy buildings are unavailable. In this study, we built three measurement systems: 1) a Stationary system with integrated affordable sensors for on-site measurements, 2) a Wireless system with affordable sensors for off-site measurements, and 3) a Mobile system consisting of expensive and accurate sensors for measuring air quality. In addition to assessing existing methods, we developed simplified methods for measuring ventilation and emission rates in dairy buildings. The three measurement systems were successfully used to measure air quality in uninsulated, semi-insulated, and fully-insulated dairy buildings between the years 2005 and 2007. When carefully calibrated, the affordable sensors in the systems gave reasonably accurate readings. The spatial air quality survey showed high variation in microclimate conditions in the dairy buildings measured. The average indoor air concentration for carbon dioxide was 950 ppm, for ammonia 5 ppm, for methane 48 ppm, for relative humidity 70%, and for inside air velocity 0.2 m/s. The average winter and summer indoor temperatures during the measurement period were -7º C and +24 ºC for the uninsulated, +3 ºC and +20 ºC for the semi-insulated and +10 ºC and +25 ºC for the fully-insulated dairy buildings. The measurement results showed that the uninsulated dairy buildings had lower indoor gas concentrations and emissions compared to fully insulated buildings. Although occasionally exceeded, the ventilation rates and average indoor air quality in the dairy buildings were largely within recommended limits. We assessed the traditional heat balance, moisture balance, carbon dioxide balance and direct airflow methods for estimating ventilation rates. The direct velocity measurement for the estimation of ventilation rate proved to be impractical for naturally ventilated buildings. Two methods were developed for estimating ventilation rates. The first method is applicable in buildings in which the ventilation can be stopped or completely closed. The second method is useful in naturally ventilated buildings with large openings and high ventilation rates where spatial gas concentrations are heterogeneously distributed. The two traditional methods (carbon dioxide and methane balances), and two newly developed methods (theoretical modelling using Fick s law and boundary layer theory, and the recirculation flux-chamber technique) were used to estimate ammonia emissions from the dairy buildings. Using the traditional carbon dioxide balance method, ammonia emissions per cow from the dairy buildings ranged from 7 g day-1 to 35 g day-1, and methane emissions per cow ranged from 96 g day-1 to 348 g day-1. The developed methods proved to be as equally accurate as the traditional methods. Variation between the mean emissions estimated with the traditional and the developed methods was less than 20%. The developed modelling procedure provided sound framework for examining the impact of production systems on ammonia emissions in dairy buildings.

Quantitative trait loci detection and benefits from marker-assisted selection in dairy cattle

Knowing the chromosomal areas or actual genes affecting the traits under selection would add more information to be used in the selection decisions which would potentially lead to higher genetic response. The first objective of this study was to map quantitative trait loci (QTL) affecting economically important traits in the Finnish Ayrshire population. The second objective was to investigate the effects of using QTL information in marker-assisted selection (MAS) on the genetic response and the linkage disequilibrium between the different parts of the genome. Whole genome scans were carried out on a grand-daughter design with 12 half-sib families and a total of 493 sons. Twelve different traits were studied: milk yield, protein yield, protein content, fat yield, fat content, somatic cell score (SCS), mastitis treatments, other veterinary treatments, days open, fertility treatments, non-return rate, and calf mortality. The average spacing of the typed markers was 20 cM with 2 to 14 markers per chromosome. Associations between markers and traits were analyzed with multiple marker regression. Significance was determined by permutation and genome-wise P-values obtained by Bonferroni correction. The benefits from MAS were investigated by simulation: a conventional progeny testing scheme was compared to a scheme where QTL information was used within families to select among full-sibs in the male path. Two QTL on different chromosomes were modelled. The effects of different starting frequencies of the favourable alleles and different size of the QTL effects were evaluated. A large number of QTL, 48 in total, were detected at 5% or higher chromosome-wise significance. QTL for milk production were found on 8 chromosomes, for SCS on 6, for mastitis treatments on 1, for other veterinary treatments on 5, for days open on 7, for fertility treatments on 7, for calf mortality on 6, and for non-return rate on 2 chromosomes. In the simulation study the total genetic response was faster with MAS than with conventional selection and the advantage of MAS persisted over the studied generations. The rate of response and the difference between the selection schemes reflected clearly the changes in allele frequencies of the favourable QTL. The disequilibrium between the polygenes and QTL was always negative and it was larger with larger QTL size. The disequilibrium between the two QTL was larger with QTL of large effect and it was somewhat larger with MAS for scenarios with starting frequencies below 0.5 for QTL of moderate size and below 0.3 for large QTL. In conclusion, several QTL affecting economically important traits of dairy cattle were detected. Further studies are needed to verify these QTL, check their presence in the present breeding population, look for pleiotropy and fine map the most interesting QTL regions. The results of the simulation studies show that using MAS together with embryo transfer to pre-select young bulls within families is a useful approach to increase the genetic merit of the AI-bulls compared to conventional selection.

Modelling interactions between farm-level structural adjustment and a regional economy: A case of the Australian rice industry

Climate change and on-going water policy reforms will likely contribute to on-farm and regional structural adjustment in Australia. This paper gathers empirical evidence of farm-level structural adjustments and integrates these with a regional equilibrium model to investigate sectoral and regional impacts of climate change and recent water use policy on rice industry. We find strong evidence of adjustments to the farming system, enabled by existing diversity in on-farm production. A further loss of water with additional pressures to adopt less intensive and larger-scale farming, will however reduce the net number of farm businesses, which may affect regional rice production. The results from a regional CGE model show impacts on the regional economy over and above the direct cost of the environmental water, although a net reduction in real economic output and real income is partially offset by gains in rest of the Australia through the reallocation or resources. There is some interest within the industry and from potential new corporate entrants in the relocation of some rice production to the north. However, strong government support would be crucial to implement such relocation.

Good science for improving policy: greenhouse gas emissions from agricultural manures

Australia’s and New Zealand’s major agricultural manure management emission sources are reported to be, in descending order of magnitude: (1) methane (CH4) from dairy farms in both countries; (2) CH4 from pig farms in Australia; and nitrous oxide (N2O) from (3) beef feedlots and (4) poultry sheds in Australia. We used literature to critically review these inventory estimates. Alarmingly for dairy farm CH4 (1), our review revealed assumptions and omissions that when addressed could dramatically increase this emission estimate. The estimate of CH4 from Australian pig farms (2) appears to be accurate, according to industry data and field measurements. The N2O emission estimates for beef feedlots (3) and poultry sheds (4) are based on northern hemisphere default factors whose appropriateness for Australia is questionable and unverified. Therefore, most of Australasia’s key livestock manure management greenhouse gas (GHG) emission profiles are either questionable or are unsubstantiated by region-specific research. Encouragingly, GHG from dairy shed manure are relatively easy to mitigate because they are a point source which can be managed by several ‘close-to-market’ abatement solutions. Reducing these manure emissions therefore constitutes an opportunity for meaningful action sooner compared with the more difficult-to-implement and long-term strategies that currently dominate agricultural GHG mitigation research. At an international level, our review highlights the critical need to carefully reassess GHG emission profiles, particularly if such assessments have not been made since the compilation of original inventories. Failure to act in this regard presents the very real risk of missing the ‘low hanging fruit’ in the rush towards a meaningful response to climate change

Israel Food Industry Commemorative Medal

Obverse: Stylized pictures of different kinds of food. Reverse: Emblem of Israel Ministry of Industry, Trade and Tourism. Stylized menorah within globe.

Flaws in the current method for calculating methane emissions during dairy manure management in New Zealand

New Zealand's Greenhouse Gas Inventory (the NZ Inventory) currently estimates methane (CH4) emissions from anaerobic dairy effluent ponds by: (1) determining the total pond volume across New Zealand; (2) dividing this volume by depth to obtain the total pond surface area; and (3) multiplying this area by an observational average CH4 flux. Unfortunately, a mathematically erroneous determination of pond volume has led to an imbalanced equation and a geometry error was made when scaling-up the observational CH4 flux. Furthermore, even if these errors are corrected, the nationwide estimate still hinges on field data from a study that used a debatable method to measure pond CH4 emissions at a single site, as well as a potentially inaccurate estimation of the amount of organic waste anaerobically treated. The development of a new methodology is therefore critically needed.

A design approach to innovation in the Australian energy industry

Electricity businesses across Australia are facing many market disruptions, such as the increasing demand from the rapid uptake of domestic air conditioners and the contrasting problematic generation from solar power connections to the grid. In this context, the opportunity to proactively leverage forthcoming technological advances in battery storage and electric vehicles to address the steeply rising cost of electricity supply has emerged. This research explores a design approach to support a business to navigate such disruptions in the current market.This study examines a design-led approach to innovation conducted over a ten month action research study within a large, risk-averse firm in the Australian energy sector. This article presents results describing a current foresight gap within the business; the response of the business to using design-led innovation to address this issue; and the tools, approaches and processes used. The business responses indicate their perception of the value of qualitative customer engagement as a path to addressing, and potentially benefiting from, disruptive innovation. It is anticipated that these results will further business model development within the company, and assist in leveraging disruptive innovations for this industry participant, thus limiting future increases in the cost of electricity supply for customers in Australia.

Australian feature films and distribution: Industry or cottage industry?

Feature films remain critical flagships to any national film industry. Australian feature films can be highly commercial endeavours that also perform symbolic functions by embodying the national imaginary in big screen based sound and imagery. They conduct a dialogue with domestic audiences as well as showcase key aspects of Australia in the global film festival circuit. As the pre-eminent filmmaking form, feature films also serve as important launchpads for the careers of many Australian writers, directors, actors and technical crew. In the wake of over a decade of diminished share of local box office obtained by Australian feature films, Australian Feature Films and Distribution: Industry or cottage industry, examines issues in the production sector affecting the performance of Australian feature films and some responses by the central funding and support screen agency, Screen Australia.

Improving Profitability to Industry Through the Identification and Management of 'tough' Fish Syndrome in Tropical Saddletail Snapper (Lutjanus Malabaricus)

OBJECTIVES: 1. To determine whether incomplete rigor mortis resolution and 'cold shock' play a role in development of tough fish syndrome (TFS) in tropical Saddletail snapper. 2. To identify links between TFS and specific physiological factors in tropical Saddletail snapper. 3. Communicate findings and recommendations to stakeholders and assist with implementation of any changes to fishing or handling practices required.

Application of shock waves in pencil manufacturing industry

A new shock wave generator has been designed, fabricated and tested for preservative impregnation studies into wood slats used for manufacturing pencils in the Shock Waves Laboratory, IISc, Bangalore. Series of experiments have been carried out in the laboratory to achieve satisfactory preservative impregnation into VATTA wood slats. The experiments have shown that it is indeed possible to impregnate preservatives into VATTA wood slats using shock waves and the depth of penetration and the retention of preservatives by wood slats is as good as the conventional methods. This method is expected to result in substantial reduction in the treatment process time compared to conventional methods that are currently being used by the pencil manufacturing industry.

Exotic plant pests–a threat to the sustainability of Australia’s grains industry

Exotic plant pests (EPPs) threaten production, market access and sustainability of Australian plant production systems. For the grains industry there are over 600 identified EPPs of which 54 are considered high priority, posing a significant threat. Despite Australia’s geographical isolation and strong quarantine systems, the threat from EPPs has never been higher with the increasing levels of travel and trade, emphasising the need for improving our efforts in prevention, preparedness and surveillance for EPPs.

Using Big Data to manage safety-related risk in the upstream oil and gas industry: A research agenda

Despite considerable effort and a broad range of new approaches to safety management over the years, the upstream oil & gas industry has been frustrated by the sector’s stubbornly high rate of injuries and fatalities. This short communication points out, however, that the industry may be in a position to make considerable progress by applying “Big Data” analytical tools to the large volumes of safety-related data that have been collected by these organizations. Toward making this case, we examine existing safety-related information management practices in the upstream oil & gas industry, and specifically note that data in this sector often tends to be highly customized, difficult to analyze using conventional quantitative tools, and frequently ignored. We then contend that the application of new Big Data kinds of analytical techniques could potentially reveal patterns and trends that have been hidden or unknown thus far, and argue that these tools could help the upstream oil & gas sector to improve its injury and fatality statistics. Finally, we offer a research agenda toward accelerating the rate at which Big Data and new analytical capabilities could play a material role in helping the industry to improve its health and safety performance.

Comparison of the impact of six heat-load management strategies on thermal responses and milk production of feed-pad and pasture fed dairy cows in a subtropical environment

Exposure to hot environments affects milk yield (MY) and milk composition of pasture and feed-pad fed dairy cows in subtropical regions. This study was undertaken during summer to compare MY and physiology of cows exposed to six heat-load management treatments. Seventy-eight Holstein-Friesian cows were blocked by season of calving, parity, milk yield, BW, and milk protein (%) and milk fat (%) measured in 2 weeks prior to the start of the study. Within blocks, cows were randomly allocated to one of the following treatments: open-sided iron roofed day pen adjacent to dairy (CID) + sprinklers (SP); CID only; non-shaded pen adjacent to dairy + SP (NSD + SP); open-sided shade cloth roofed day pen adjacent to dairy (SCD); NSD + sprinkler (sprinkler on for 45 min at 1100 h if mean respiration rate >80 breaths per minute (NSD + WSP)); open-sided shade cloth roofed structure over feed bunk in paddock + 1 km walk to and from the dairy (SCP + WLK). Sprinklers for CID + SP and NSD + SP cycled 2 min on, 12 min off when ambient temperature >26°C. The highest milk yields were in the CID + SP and CID treatments (23.9 L cow−1 day−1), intermediate for NSD + SP, SCD and SCP + WLK (22.4 L cow−1 day−1), and lowest for NSD + WSP (21.3 L cow−1 day−1) (P < 0.05). The highest (P < 0.05) feed intakes occurred in the CID + SP and CID treatments while intake was lowest (P < 0.05) for NSD + WSP and SCP + WLK. Weather data were collected on site at 10-min intervals, and from these, THI was calculated. Nonlinear regression modelling of MY × THI and heat-load management treatment demonstrated that cows in CID + SP showed no decline in MY out to a THI break point value of 83.2, whereas the pooled MY of the other treatments declined when THI >80.7. A combination of iron roof shade plus water sprinkling throughout the day provided the most effective control of heat load.

Knowledge management research in the construction industry: a review

Purpose: Knowledge management (KM) is important to the knowledge-intensive construction industry. The diversified and changing nature of works in this field warrants us to stocktake, identify changes and map out KM research framework for future exploration. Design/methodology/approach: The study involves three aspects. First, three stages of KM research in construction were distinguished in terms of the time distribution of 217 target publications. Major topics in the stages were extracted for understanding the changes of research emphasis from evolutionary perspective. Second, the past works were summed up in a three-dimensional research framework in terms of management organization, managerial methodology and approach, and managerial objective. Finally, potential research orientations in the future were predicted to expand the existing research framework. Findings: It was found that (1) KM research has significantly blossomed in the last two decades with a great potential; (2) major topics of KM were changing in terms of technology, technique, organization, attribute of knowledge and research objectives; (3) past KM studies centred around management organization, managerial methodology and approach, and managerial objective thus a three-dimensional research framework was proposed; (4) within the research framework, team-level, project-level and firm-level KM were studied to achieve project, organizational and competitive objectives by integrated methodologies of information technology, social technique and KM process tool; and (5) nine potential research orientations were predicted corresponding to the three dimensions. Finally, an expanded research framework was proposed to encourage and guide future research works in this field. Research limitations/implications: The paper only focused on the construction industry. The findings need further exploration in order to discover any possible missing important research works which were not published in English or not included in the time period. Originality/value: The paper formed a systematic framework of KM research in construction and predicted the potential research orientations. It provides much value for the researchers who want to understand the past and the future of global KM research in the construction industry.