Evaluation of thermochemical biomass conversion in fluidized bed

Dado o aumento acelerado dos preços dos combustíveis fósseis e as incertezas quanto à sua disponibilidade futura, tem surgido um novo interesse nas tecnologias da biomassa aplicadas à produção de calor, eletricidade ou combustíveis sintéticos. Não obstante, para a conversão termoquímica de uma partícula de biomassa sólida concorrem fenómenos bastante complexos que levam, em primeiro lugar, à secagem do combustível, depois à pirólise e finalmente à combustão ou gasificação propriamente ditas. Uma descrição relativamente incompleta de alguns desses estágios de conversão constitui ainda um obstáculo ao desenvolvimento das tecnologias que importa ultrapassar. Em particular, a presença de elevados conteúdos de matéria volátil na biomassa põe em evidência o interesse prático do estudo da pirólise. A importância da pirólise durante a combustão de biomassa foi evidenciada neste trabalho através de ensaios realizados num reator piloto de leito fluidizado borbulhante. Verificou-se que o processo ocorre em grande parte à superfície do leito com chamas de difusão devido à libertação de voláteis, o que dificulta o controlo da temperatura do reator acima do leito. No caso da gasificação de biomassa a pirólise pode inclusivamente determinar a eficiência química do processo. Isso foi mostrado neste trabalho durante ensaios de gasificação num reator de leito fluidizado de 2MWth, onde um novo método de medição permitiu fechar o balanço de massa ao gasificador e monitorizar o grau de conversão da biomassa. A partir destes resultados tornou-se clara a necessidade de descrever adequadamente a pirólise de biomassa com vista ao projeto e controlo dos processos. Em aplicações de engenharia há particular interesse na estequiometria e propriedades dos principais produtos pirolíticos. Neste trabalho procurou-se responder a esta necessidade, inicialmente através da estruturação de dados bibliográficos sobre rendimentos de carbonizado, líquidos pirolíticos e gases, assim como composições elementares e poderes caloríficos. O resultado traduziu-se num conjunto de parâmetros empíricos de interesse prático que permitiram elucidar o comportamento geral da pirólise de biomassa numa gama ampla de condições operatórias. Para além disso, propôs-se um modelo empírico para a composição dos voláteis que pode ser integrado em modelos compreensivos de reatores desde que os parâmetros usados sejam adequados ao combustível ensaiado. Esta abordagem despoletou um conjunto de ensaios de pirólise com várias biomassas, lenhina e celulose, e temperaturas entre os 600 e 975ºC. Elevadas taxas de aquecimento do combustível foram alcançadas em reatores laboratoriais de leito fluidizado borbulhante e leito fixo, ao passo que um sistema termo-gravimétrico permitiu estudar o efeito de taxas de aquecimento mais baixas. Os resultados mostram que, em condições típicas de processos de combustão e gasificação, a quantidade de voláteis libertada da biomassa é pouco influenciada pela temperatura do reator mas varia bastante entre combustíveis. Uma análise mais aprofundada deste assunto permitiu mostrar que o rendimento de carbonizado está intimamente relacionado com o rácio O/C do combustível original, sendo proposto um modelo simples para descrever esta relação. Embora a quantidade total de voláteis libertada seja estabelecida pela composição da biomassa, a respetiva composição química depende bastante da temperatura do reator. Rendimentos de espécies condensáveis (água e espécies orgânicas), CO2 e hidrocarbonetos leves descrevem um máximo relativamente à temperatura para dar lugar a CO e H2 às temperaturas mais altas. Não obstante, em certas gamas de temperatura, os rendimentos de algumas das principais espécies gasosas (e.g. CO, H2, CH4) estão bem correlacionados entre si, o que permitiu desenvolver modelos empíricos que minimizam o efeito das condições operatórias e, ao mesmo tempo, realçam o efeito do combustível na composição do gás. Em suma, os ensaios de pirólise realizados neste trabalho permitiram constatar que a estequiometria da pirólise de biomassa se relaciona de várias formas com a composição elementar do combustível original o que levanta várias possibilidades para a avaliação e projeto de processos de combustão e gasificação de biomassa.

Reconfigurable transmitters for software-defined radios

Flexible radio transmitters based on the Software-Defined Radio (SDR) concept are gaining an increased research importance due to the unparalleled proliferation of new wireless standards operating at different frequencies, using dissimilar coding and modulation schemes, and targeted for different ends. In this new wireless communications paradigm, the physical layer of the radio transmitter must be able to support the simultaneous transmission of multi-band, multi-rate, multi-standard signals, which in practice is very hard or very inefficient to implement using conventional approaches. Nevertheless, the last developments in this field include novel all-digital transmitter architectures where the radio datapath is digital from the baseband up to the RF stage. Such concept has inherent high flexibility and poses an important step towards the development of SDR-based transmitters. However, the truth is that implementing such radio for a real world communications scenario is a challenging task, where a few key limitations are still preventing a wider adoption of this concept. This thesis aims exactly to address some of these limitations by proposing and implementing innovative all-digital transmitter architectures with inherent higher flexibility and integration, and where improving important figures of merit, such as coding efficiency, signal-to-noise ratio, usable bandwidth and in-band and out-of-band noise will also be addressed. In the first part of this thesis, the concept of transmitting RF data using an entirely digital approach based on pulsed modulation is introduced. A comparison between several implementation technologies is also presented, allowing to state that FPGAs provide an interesting compromise between performance, power efficiency and flexibility, thus making them an interesting choice as an enabling technology for pulse-based all-digital transmitters. Following this discussion, the fundamental concepts inherent to pulsed modulators, its key advantages, main limitations and typical enhancements suitable for all-digital transmitters are also presented. The recent advances regarding the two most common classes of pulse modulated transmitters, namely the RF and the baseband-level are introduced, along with several examples of state-of-the-art architectures found on the literature. The core of this dissertation containing the main developments achieved during this PhD work is then presented and discussed. The first key contribution to the state-of-the-art presented here consists in the development of a novel ΣΔ-based all-digital transmitter architecture capable of multiband and multi-standard data transmission in a very flexible and integrated way, where the pulsed RF output operating in the microwave frequency range is generated inside a single FPGA device. A fundamental contribution regarding the simultaneous transmission of multiple RF signals is then introduced by presenting and describing novel all-digital transmitter architectures that take advantage of multi-gigabit data serializers available on current high-end FPGAs in order to transmit in a time-interleaved approach multiple independent RF carriers. Further improvements in this design approach allowed to provide a two-stage up-conversion transmitter architecture enabling the fine frequency tuning of concurrent multichannel multi-standard signals. Finally, further improvements regarding two key limitations inherent to current all-digital transmitter approaches are then addressed, namely the poor coding efficiency and the combined high quality factor and tunability requirements of the RF output filter. The followed design approach based on poliphase multipath circuits allowed to create a new FPGA-embedded agile transmitter architecture that significantly improves important figures of merit, such as coding efficiency and SNR, while maintains the high flexibility that is required for supporting multichannel multimode data transmission.

Challenges in mercury speciation and fractionation in soil and sediment

This investigation focused on the development, test and validation of methodologies for mercury fractionation and speciation in soil and sediment. After an exhaustive review of the literature, several methods were chosen and tested in well characterised soil and sediment samples. Sequential extraction procedures that divide mercury fractions according to their mobility and potential availability in the environment were investigated. The efficiency of different solvents for fractionation of mercury was evaluated, as well as the adequacy of different analytical instruments for quantification of mercury in the extracts. Kinetic experiments to establish the equilibrium time for mercury release from soil or sediment were also performed. It was found that in the studied areas, only a very small percentage of mercury is present as mobile species and that mobility is associated to higher aluminium and manganese contents, and that high contents of organic matter and sulfur result in mercury tightly bound to the matrix. Sandy soils tend to release mercury faster that clayey soils, and therefore, texture of soil or sediment has a strong influence on the mobility of mercury. It was also understood that analytical techniques for quantification of mercury need to be further developed, with lower quantification limits, particularly for mercury quantification of less concentrated fractions: water-soluble e exchangeable. Although the results provided a better understanding of the distribution of mercury in the sample, the complexity of the procedure limits its applicability and robustness. A proficiency-testing scheme targeting total mercury determination in soil, sediment, fish and human hair was organised in order to evaluate the consistency of results obtained by different laboratories, applying their routine methods to the same test samples. Additionally, single extractions by 1 mol L-1 ammonium acetate solution, 0.1 mol L-1 HCl and 0.1 mol L-1 CaCl2, as well as extraction of the organometallic fraction were proposed for soil; the last was also suggested for sediment and fish. This study was important to update the knowledge on analytical techniques that are being used for mercury quantification, the associated problems and sources of error, and to improve and standardize mercury extraction techniques, as well as to implement effective strategies for quality control in mercury determination. A different, “non chemical-like” method for mercury species identification was developed, optimised and validated, based on the thermo-desorption of the different mercury species. Compared to conventional extraction procedures, this method has advantages: it requires little to no sample treatment; a complete identification of species present is obtained in less than two hours; mercury losses are almost neglectable; can be considered “clean”, as no residues are produced; the worldwide comparison of results obtained is easier and reliable, an important step towards the validation of the method. Therefore, the main deliverables of this PhD thesis are an improved knowledge on analytical procedures for identification and quantification of mercury species in soils and sediments, as well as a better understanding of the factors controlling the behaviour of mercury in these matrices.

Advanced energy efficient coordinated multi-point transmission for OFDMA

The ever-growing energy consumption in mobile networks stimulated by the expected growth in data tra ffic has provided the impetus for mobile operators to refocus network design, planning and deployment towards reducing the cost per bit, whilst at the same time providing a signifi cant step towards reducing their operational expenditure. As a step towards incorporating cost-eff ective mobile system, 3GPP LTE-Advanced has adopted the coordinated multi-point (CoMP) transmission technique due to its ability to mitigate and manage inter-cell interference (ICI). Using CoMP the cell average and cell edge throughput are boosted. However, there is room for reducing energy consumption further by exploiting the inherent exibility of dynamic resource allocation protocols. To this end packet scheduler plays the central role in determining the overall performance of the 3GPP longterm evolution (LTE) based on packet-switching operation and provide a potential research playground for optimizing energy consumption in future networks. In this thesis we investigate the baseline performance for down link CoMP using traditional scheduling approaches, and subsequently go beyond and propose novel energy e fficient scheduling (EES) strategies that can achieve power-e fficient transmission to the UEs whilst enabling both system energy effi ciency gain and fairness improvement. However, ICI can still be prominent when multiple nodes use common resources with di fferent power levels inside the cell, as in the so called heterogeneous networks (Het- Net) environment. HetNets are comprised of two or more tiers of cells. The rst, or higher tier, is a traditional deployment of cell sites, often referred to in this context as macrocells. The lower tiers are termed small cells, and can appear as microcell, picocells or femtocells. The HetNet has attracted signiffi cant interest by key manufacturers as one of the enablers for high speed data at low cost. Research until now has revealed several key hurdles that must be overcome before HetNets can achieve their full potential: bottlenecks in the backhaul must be alleviated, as well as their seamless interworking with CoMP. In this thesis we explore exactly the latter hurdle, and present innovative ideas on advancing CoMP to work in synergy with HetNet deployment, complemented by a novel resource allocation policy for HetNet tighter interference management. As system level simulator has been used to analyze the proposed algorithm/protocols, and results have concluded that up to 20% energy gain can be observed.

Síntese e transformações de compostos do tipo pirazol e 1,2,3-triazol

Compostos do tipo pirazol e 1,2,3-triazol encontram-se presentes em inúmeras moléculas biologicamente ativas. Muitos fármacos atualmente comercializados ou em fase de estudos clínicos contêm na sua estrutura base núcleos de pirazol ou 1,2,3-triazol. Por isso, estes compostos têm sido alvo de intensa pesquisa na procura de novas moléculas com potenciais aplicações medicinais e agroquímicas. Nesta dissertação são descritas novas vias de síntese de novos compostos do tipo pirazol e 1,2,3-triazol. No primeiro capítulo apresenta-se uma breve revisão bibliográfica sobre a atividade biológica, ocorrência natural e métodos de síntese de pirazóis e seus derivados. O segundo capítulo foca-se na síntese de (E)-2-estiril-3-halo-4H-cromen-4-onas e sua transformação em 3(5)-aril-5(3)-[2-(2-hidroxifenil)-2-oxoetil-1H-pirazóis. Em primeiro lugar faz-se uma revisão bibliográfica sobre as (E)-2-estiril-4H-cromen-4-onas e a sua semelhança estrutural com as flavonas, a sua importância e ocorrência natural e métodos de síntese. São ainda abordadas as metodologias mais utilizadas para a síntese de derivados halogenados de (E)-2-estiril-4H-cromen-4-onas. Seguidamente são apresentados e discutidos os resultados da síntese de (E)-3-bromo-2-estiril-4H-cromen-4-onas através da reação de 5-aril-3-hidroxi-1-(2-hidroxifenil)penta-2,4-dien-1-onas com NBS, sob irradiação com micro-ondas, tendo sido estabelecida uma nova metodologia mais eficiente, rápida e regiosseletiva para a síntese de (E)-3-bromo-2-estiril-4H-cromen-4-onas, na ausência de solvente. São igualmente apresentados os resultados da síntese regiosseletiva de (E)-2-estiril-3-iodo-4H-cromen-4-onas através da reação de 5-aril-3-hidroxi-1-(2-hidroxifenil)penta-2,4-dien-1-onas com NIS e TFA/TFAA/NaOAc. Em ambos os métodos de halogenação desenvolvidos, obtiveram-se como produtos secundários as (E)-2-estiril-4H-cromen-4-onas correspondentes. Seguidamente é apresentado o estudo da reação de (E)-2-estiril-3-halo-4H-cromen-4-onas com hidrato de hidrazina. Ao contrário do esperado, obtiveram-se os 3(5)-aril-5(3)-[2-(2-hidroxifenil)-2-oxoetil-1H-pirazóis através de uma reação de adição conjugada 1,6-, de hidrazina à posição C- da cromona com consequente abertura do anel, seguida de uma adição conjugada 1,4- intramolecular. Estes resultados demonstraram que esta reação segue um mecanismo diferente daquele que está reportado na literatura para a reação de (E)-2-estiril-4H-cromen-4-onas não halogenadas em C-3 com hidrato de hidrazina. No terceiro capítulo apresenta-se uma breve revisão bibliográfica sobre as propriedades, aplicações e metodologias de síntese de 1,2,3-triazóis, dando mais relevância às reações de cicloadição 1,3-dipolar e de “click-chemistry”. Seguidamente descrevem-se os resultados obtidos na reação de (E)-5(3)-estiril-3(5)-(2-hidroxifenil)-1H-pirazóis com a azida de sódio para obtenção de díades pirazol-1,2,3-triazol. No entanto esta reação deu origem a novos 5(3)-(2-aril-2-azidoetil)-3(5)-(2-hidroxifenil)-1H-pirazóis e não às díades pirazol-1,2,3-triazol pretendidas. Como o resultado não foi o esperado, desenvolveu-se outra metodologia de síntese, que envolve, num primeiro, a reação de (E)-2-estiril-4H-cromen-4-onas com azida de sódio, dando origem a 5(4)-aril-4(5)-(cromon-2-il)-1H-1,2,3-triazóis. No passo seguinte, efetuou-se a reação destes compostos com hidrato de hidrazina tendo ocorrido a formação das diades 5(4)-aril-4(5)-[3(5)-(2-hidroxifenil)-1H-pirazol-5(3)-il]-1H-1,2,3-triazol pretendidas. No quarto capítulo, estudou-se a reatividade de (E)-5(3)-estiril-3(5)-(2-hidroxifenil)-1H-pirazóis em reações de iodação com vista à obtenção de 4-iodo-1H-pirazóis. Apresenta-se uma breve revisão bibliográfica sobre os diferentes métodos descritos na literatura para a iodação de compostos heterocíclicos aromáticos, nomeadamente para a obtenção de 4-iodo-1H-pirazóis. Dos vários sistemas de iodação testados, o sistema oxidativo I2/CAN foi o que deu melhores resultados na iodação dos (E)-5(3)-estiril-3(5)-(2-hidroxifenil)-1H-pirazóis. Este método permitiu iodar a posição C-4 do núcleo de pirazol apenas para os derivados que possuem o grupo nitro ou o átomo de cloro no anel do grupo estirilo, obtendo-se o 3(5)-(2-hidroxifenil)-4-iodo-5(3)-(4-nitrofenil)vinil-1H-pirazol e o 5(3)-(4-clorofenil)vinil)-3(5)-(2-hidroxi-5-iodofenil)-4-iodo-1H-pirazol; no entanto, para os restantes derivados, verificou-se apenas a iodação nas posições ativadas do anel fenólico. Todos os novos compostos sintetizados foram caraterizados estruturalmente recorrendo a estudos de espetroscopia de ressonância magnética nuclear (RMN) mono e bidimensionais. Sempre que possível, para uma caraterização estrutural mais completa, foram efetuados espetros de massa (EM) e análises elementares ou espetros de massa de alta resolução (EMAR) para todos os novos compostos sintetizados. Finalmente são apresentadas as conclusões gerais deste trabalho e perspetivas futuras.

Electromechanical properties of engineered lead free potassium sodium niobate based materials

K0.5Na0.5NbO3 (KNN), is the most promising lead free material for substituting lead zirconate titanate (PZT) which is still the market leader used for sensors and actuators. To make KNN a real competitor, it is necessary to understand and to improve its properties. This goal is pursued in the present work via different approaches aiming to study KNN intrinsic properties and then to identify appropriate strategies like doping and texturing for designing better KNN materials for an intended application. Hence, polycrystalline KNN ceramics (undoped, non-stoichiometric; NST and doped), high-quality KNN single crystals and textured KNN based ceramics were successfully synthesized and characterized in this work. Polycrystalline undoped, non-stoichiometric (NST) and Mn doped KNN ceramics were prepared by conventional ceramic processing. Structure, microstructure and electrical properties were measured. It was observed that the window for mono-phasic compositions was very narrow for both NST ceramics and Mn doped ceramics. For NST ceramics the variation of A/B ratio influenced the polarization (P-E) hysteresis loop and better piezoelectric and dielectric responses could be found for small stoichiometry deviations (A/B = 0.97). Regarding Mn doping, as compared to undoped KNN which showed leaky polarization (P-E) hysteresis loops, B-site Mn doped ceramics showed a well saturated, less-leaky hysteresis loop and a significant properties improvement. Impedance spectroscopy was used to assess the role of Mn and a relation between charge transport – defects and ferroelectric response in K0.5Na0.5NbO3 (KNN) and Mn doped KNN ceramics could be established. At room temperature the conduction in KNN which is associated with holes transport is suppressed by Mn doping. Hence Mn addition increases the resistivity of the ceramic, which proved to be very helpful for improving the saturation of the P-E loop. At high temperatures the conduction is dominated by the motion of ionized oxygen vacancies whose concentration increases with Mn doping. Single crystals of potassium sodium niobate (KNN) were grown by a modified high temperature flux method. A boron-modified flux was used to obtain the crystals at a relatively low temperature. XRD, EDS and ICP analysis proved the chemical and crystallographic quality of the crystals. The grown KNN crystals exhibit higher dielectric permittivity (29,100) at the tetragonal-to-cubic phase transition temperature, higher remnant polarization (19.4 μC/cm2) and piezoelectric coefficient (160 pC/N) when compared with the standard KNN ceramics. KNN single crystals domain structure was characterized for the first time by piezoforce response microscopy. It could be observed that <001> - oriented potassium sodium niobate (KNN) single crystals reveal a long range ordered domain pattern of parallel 180° domains with zig-zag 90° domains. From the comparison of KNN Single crystals to ceramics, It is argued that the presence in KNN single crystal (and absence in KNN ceramics) of such a long range order specific domain pattern that is its fingerprint accounts for the improved properties of single crystals. These results have broad implications for the expanded use of KNN materials, by establishing a relation between the domain patterns and the dielectric and ferroelectric response of single crystals and ceramics and by indicating ways of achieving maximised properties in KNN materials. Polarized Raman analysis of ferroelectric potassium sodium niobate (K0.5Na0.5)NbO3 (KNN) single crystals was performed. For the first time, an evidence is provided that supports the assignment of KNN single crystals structure to the monoclinic symmetry at room temperature. Intensities of A′, A″ and mixed A′+A″ phonons have been theoretically calculated and compared with the experimental data in dependence of crystal rotation, which allowed the precise determination of the Raman tensor coefficients for (non-leaking) modes in monoclinic KNN. In relation to the previous literature, this study clarifies that assigning monoclinic phase is more suitable than the orthorhombic one. In addition, this study is the basis for non-destructive assessments of domain distribution by Raman spectroscopy in KNN-based lead-free ferroelectrics with complex structures. Searching a deeper understanding of the electrical behaviour of both KNN single crystal and polycrystalline materials for the sake of designing optimized KNN materials, a comparative study at the level of charge transport and point defects was carried out by impedance spectroscopy. KNN single crystals showed lower conductivity than polycrystals from room temperature up to 200 ºC, but above this temperature polycrystalline KNN displays lower conductivity. The low temperature (T < 200 ºC) behaviour reflects the different processing conditions of both ceramics and single crystals, which account for less defects prone to charge transport in the case of single crystals. As temperature increases (T > 200 ºC) single crystals become more conductive than polycrystalline samples, in which grain boundaries act as barriers to charge transport. For even higher temperatures the conductivity difference between both is increased due to the contribution of ionic conduction in single crystals. Indeed the values of activation energy calculated to the high temperature range (T > 300 ºC) were 1.60 and 0.97 eV, confirming the charge transport due to ionic conduction and ionized oxygen vacancies in single crystals and polycrystalline KNN, respectively. It is suggested that single crystals with low defects content and improved electromechanical properties could be a better choice for room temperature applications, though at high temperatures less conductive ceramics may be the choice, depending on the targeted use. Aiming at engineering the properties of KNN polycrystals towards the performance of single crystals, the preparation and properties study of (001) – oriented (K0.5Na0.5)0.98Li0.02NbO3 (KNNL) ceramics obtained by templated grain growth (TGG) using KNN single crystals as templates was undertaken. The choice of KNN single crystals templates is related with their better properties and to their unique domain structure which were envisaged as a tool for templating better properties in KNN ceramics too. X-ray diffraction analysis revealed for the templated ceramics a monoclinic structure at room temperature and a Lotgering factor (f) of 40% which confirmed texture development. These textured ceramics exhibit a long range ordered domain pattern consisting of 90º and 180º domains, similar to the one observed in the single crystals. Enhanced dielectric (13017 at TC), ferroelectric (2Pr = 42.8 μC/cm2) and piezoelectric (d33 = 280 pC/N) properties are observed for textured KNNL ceramics as compared to the randomly oriented ones. This behaviour is suggested to be due to the long range ordered domain patterns observed in the textured ceramics. The obtained results as compared with the data previously reported on texture KNN based ceramics confirm that superior properties were found due to ordered repeated domain pattern. This study provides an useful approach towards properties improvement of KNN-based piezoelectric ceramics. Overall, the present results bring a significant contribution to the pool of knowledge on the properties of sodium potassium niobate materials: a relation between the domain patterns and di-, ferro-, and piezo-electric response of single crystals and ceramics was demonstrated and ways of engineering maximised properties in KNN materials, for example by texturing were established. This contribution is envisaged to have broad implications for the expanded use of KNN over the alternative lead-based materials.

Estudos de síntese e transformação de cromonas e 4-quinolonas

Esta dissertação está dividida em duas partes. Na primeira parte reportam-se métodos de síntese de (E)-3-estirilflavonas e (E)/(Z)-2-aril- 4-cloro-3-estiril-2H-cromenos e estudos de ciclização das (E)-3- estirilflavonas em 5-arilbenzo[c]xantonas. Na segunda parte desenvolveram-se novas rotas de síntese de (E)-2-aril-3-estiril-4- quinolonas e posterior transformação em 5-fenil-12- metilbenzo[c]acridonas e 2,4-diarilfuro[3,2-c]quinolinas. Nesta parte estudou-se também a transformação de 2-aril-4-cloro-1,2-dihidroquinolina- 1,3-dicarbaldeídos em (E)/(Z)-2-aril-4-cloro-3-estiril-1,2- di-hidroquinolina-1-carbaldeídos. A síntese de novos derivados de (E)-3-estirilflavonas, abordada na primeira parte desta dissertação, envolveu estudos de otimização da reação de bromação seguida de ciclização de 3-aril-1-(2- hidroxiaril)propano-1,3-dionas/3-aril-3-hidroxi-1-(2-hidroxiaril)prop-2- en-1-onas em 3-bromoflavonas e o desenvolvimento de uma nova rota de síntese de 3-metilflavonas. As 3-metilflavonas foram sujeitas a bromação e seguidamente transformadas em sais de fosfónio antes de serem utilizadas na síntese de (E)-3-estirilflavonas via reação de Wittig. As 3-bromoflavonas foram também usadas na síntese de (E)-3- estirilflavonas via reação de Heck. A síntese de novos derivados de (E)/(Z)-2-aril-4-cloro-3-estiril-2H-cromenos, via reação de Wittig, envolveu a síntese e formilação de flavanonas. A última transformação reportada na primeira parte desta dissertação é a síntese de 5-arilbenzo[c]xantonas por reação de eletrociclização seguida de oxidação de (E)-3-estirilflavonas. Na segunda parte desta dissertação são estudadas duas vias de síntese de 2-aril-1-metil-4-quinolonas. A primeira via de síntese envolve a síntese de N-(2-acetilfenil)benzamidas, sua ciclização em 4-quinolonas seguida de metilação destas. A segunda via envolve a metilação e ciclização de N-(2-acetilfenil)benzamidas obtendo-se, num só passo, as 2-aril-1-metil-4-quinolonas. Posterior iodação das 2-aril-1-metil-4- quinolonas e subsequente reação de Heck das 2-aril-3-iodo-1-metil-4- quinolonas com estirenos comerciais possibilitaram a síntese de (E)-2- aril-3-estiril-1-metil-4-quinolonas. Estudos de eletrociclização seguidos de oxidação das (E)-2-aril-3-estiril-1-metil-4-quinolonas utilizando uma lâmpada de UV de mercúrio de alta pressão possibilitou a síntese de 5- fenil-12-metilbenzo[c]acridonas, enquanto que o aquecimento em refluxo de 1,2,4-triclorobenzeno deu origem a 2,4-diarilfuro[3,2- c]quinolinas. Nesta segunda parte aborda-se também a síntese de 2-aril-4-cloro-1,2- di-hidroquinolina-1,3-dicarbaldeídos, a partir da formilação de 2-aril- 2,3-di-hidro-4-quinolonas e a sua transformação em (E)/(Z)-2-aril-4- cloro-3-estiril-1,2-di-hidroquinolina-1-carbaldeídos por reação de Wittig. Todos os compostos sintetizados foram caracterizados por espectroscopia de ressonância magnética nuclear de protão e carbono 13C, espectros bidimensionais de correlação heteronuclear (HMBC e HSQC) e, nalguns casos espectros de efeito nuclear Overhauser (NOESY). Os novos produtos foram igualmente caracterizados por espectrometria de massa e sempre que possível análise elementar ou espectrometria de massa de alta resolução.

Concentration of tumor biomarkers using aqueous biphasic systems

According to the World Health Organization, around 8.2 million people die each year with cancer. Most patients do not perform routine diagnoses and the symptoms, in most situations, occur when the patient is already at an advanced stage of the disease, consequently resulting in a high cancer mortality. Currently, prostate cancer is the second leading cause of death among males worldwide. In Portugal, this is the most diagnosed type of cancer and the third that causes more deaths. Taking into account that there is no cure for advanced stages of prostate cancer, the main strategy comprises an early diagnosis to increase the successful rate of the treatment. The prostate specific antigen (PSA) is an important biomarker of prostate cancer that can be detected in biological fluids, including blood, urine and semen. However, the commercial kits available are addressed for blood samples and the commonly used analytical methods for their detection and quantification requires specialized staff, specific equipment and extensive sample processing, resulting in an expensive process. Thus, the aim of this MSc thesis consisted on the development of a simple, efficient and less expensive method for the extraction and concentration of PSA from urine samples using aqueous biphasic systems (ABS) composed of ionic liquids. Initially, the phase diagrams of a set of aqueous biphasic systems composed of an organic salt and ionic liquids were determined. Then, their ability to extract PSA was ascertained. The obtained results reveal that in the tested systems the prostate specific antigen is completely extracted to the ionic-liquid-rich phase in a single step. Subsequently, the applicability of the investigated ABS for the concentration of PSA was addressed, either from aqueous solutions or urine samples. The low concentration of this biomarker in urine (clinically significant below 150 ng/mL) usually hinders its detection by conventional analytical techniques. The obtained results showed that it is possible to extract and concentrate PSA, up to 250 times in a single-step, so that it can be identified and quantified using less expensive techniques.

Concentration of tumor biomarkers using aqueous biphasic systems

According to the World Health Organization, around 8.2 million people die each year with cancer. Most patients do not perform routine diagnoses and the symptoms, in most situations, occur when the patient is already at an advanced stage of the disease, consequently resulting in a high cancer mortality. Currently, prostate cancer is the second leading cause of death among males worldwide. In Portugal, this is the most diagnosed type of cancer and the third that causes more deaths. Taking into account that there is no cure for advanced stages of prostate cancer, the main strategy comprises an early diagnosis to increase the successful rate of the treatment. The prostate specific antigen (PSA) is an important biomarker of prostate cancer that can be detected in biological fluids, including blood, urine and semen. However, the commercial kits available are addressed for blood samples and the commonly used analytical methods for their detection and quantification requires specialized staff, specific equipment and extensive sample processing, resulting in an expensive process. Thus, the aim of this MSc thesis consisted on the development of a simple, efficient and less expensive method for the extraction and concentration of PSA from urine samples using aqueous biphasic systems (ABS) composed of ionic liquids. Initially, the phase diagrams of a set of aqueous biphasic systems composed of an organic salt and ionic liquids were determined. Then, their ability to extract PSA was ascertained. The obtained results reveal that in the tested systems the prostate specific antigen is completely extracted to the ionic-liquid-rich phase in a single step. Subsequently, the applicability of the investigated ABS for the concentration of PSA was addressed, either from aqueous solutions or urine samples. The low concentration of this biomarker in urine (clinically significant below 150 ng/mL) usually hinders its detection by conventional analytical techniques. The obtained results showed that it is possible to extract and concentrate PSA, up to 250 times in a single-step, so that it can be identified and quantified using less expensive techniques.

Development of a sustainable method for the extraction of lycopene and β-carotene from food wastes

The main objective of the present work is the study of a profitable process not only in the extraction and selective separation of lycopene and β-carotene, two compounds present in tomato, but also in its potential application to food industry wastes. This is one of the industries that produce larger amounts of wastes, which are rich in high value biomolecules with great economic interest. However, the conventional methods used to extract this kind of compounds are expensive which limits their application at large scale. Lycopene and βcarotene are carotenoids with high commercial value, known for their antioxidant activity and benefits to human health. Their biggest source is tomato, one of the world’s most consumed fruits, reason for which large quantities of waste is produced. This work focuses on the study of diverse solvents with a high potential to extract carotenoids from tomato, as well as the search for more environmentally benign solvents than those currently used to extract lycopene and β-carotene from biomass. Additionally, special attention was paid to the creation of a continuous process that would allow the fractionation of the compounds for further purification. Thus, the present work started with the extraction of both carotenoids using a wide range of solvents, namely, organic solvents, conventional salts, ionic liquids, polymers and surfactants. In this stage, each solvent was evaluated in what regards their capacity of extraction as well as their penetration ability in biomass. The results collected showed that an adequate selection of the solvents may lead to the complete extraction of both carotenoids in one single step, particularly acetone and tetrahydrofuran were the most effective ones. However, the general low penetration capacity of salts, ionic liquids, polymers and surfactants makes these solvents ineffective in the solid-liquid extraction process. As the organic solvents showed the highest capacity to extract lycopene and βcarotene, in particular tetrahydrofuran and acetone, the latter solvent used in the development process of fractionation, using to this by strategic use of solvents. This step was only successfully developed through the manipulation of the solubility of each compound in ethanol and n-hexane. The results confirmed the possibility of fractionating the target compounds using the correct addition order of the solvents. Approximately, 39 % of the β-carotene was dissolved in ethanol and about 64 % of lycopene was dissolved in n-hexane, thus indicating their separation for two different solvents which shows the selective character of the developed process without any prior stage optimization. This study revealed that the use of organic solvents leads to selective extraction of lycopene and β-carotene, allowing diminishing the numerous stages involved in conventional methods. At the end, it was possible to idealize a sustainable and of high industrial relevance integrated process, nevertheless existing the need for additional optimization studies in the future.

Identification of molecules and pathways regulating mistranslation in Candida albicans

Candida albicans is the major fungal pathogen in humans, causing diseases ranging from mild skin infections to severe systemic infections in immunocompromised individuals. The pathogenic nature of this organism is mostly due to its capacity to proliferate in numerous body sites and to its ability to adapt to drastic changes in the environment. Candida albicans exhibit a unique translational system, decoding the leucine-CUG codon ambiguously as leucine (3% of codons) and serine (97%) using a hybrid serine tRNA (tRNACAGSer). This tRNACAGSer is aminoacylated by two aminoacyl tRNA synthetases (aaRSs): leucyl-tRNA synthetase (LeuRS) and seryl-tRNA synthetase (SerRS). Previous studies showed that exposure of C. albicans to macrophages, oxidative, pH stress and antifungals increases Leu misincorporation levels from 3% to 15%, suggesting that C. albicans has the ability to regulate mistranslation levels in response to host defenses, antifungals and environmental stresses. Therefore, the hypothesis tested in this work is that Leu and Ser misincorporation at CUG codons is dependent upon competition between the LeuRS and SerRS for the tRNACAGSer. To test this hypothesis, levels of the SerRS and LeuRS were indirectly quantified under different physiological conditions, using a fluorescent reporter system that measures the activity of the respective promoters. Results suggest that an increase in Leu misincorporation at CUG codons is associated with an increase in LeuRS expression, with levels of SerRS being maintained. In the second part of the work, the objective was to identify putative regulators of SerRS and LeuRS expression. To accomplish this goal, C. albicans strains from a transcription factor knock-out collection were transformed with the fluorescent reporter system and expression of both aaRSs was quantified. Alterations in the LeuRS/SerRS expression of mutant strains compared to wild type strain allowed the identification of 5 transcription factors as possible regulators of expression of LeuRS and SerRS: ASH1, HAP2, HAP3, RTG3 and STB5. Globally, this work provides the first step to elucidate the molecular mechanism of regulation of mistranslation in C. albicans.

Uma abordagem de matabolómica no estudo comparativo do metabolismo de glucose e galactose no patogénico humano Streptococcus pneumoniae

Dissertação mest., Ciências Biomédicas, Universidade do Algarve, 2010

Application of DPSIR framework integrated with multiple regression model to simulate Guadiana catchment - estuary continuum, south eastern Iberia

Dissertação de Mestrado, Gestão da Água e da Costa, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2010

Modelling underwater acoustic noise as a tool for coastal management

Dissertação de Mestrado, Gestão da Água e da Costa, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2009

Para uma teoria da anedota popular portuguesa

Corpo errático e volátil por excelência, a anedota constitui porventura o género do discurso através do qual uma comunidade (conceito, como se sabe, cada vez mais alargado) mais dinâmica e prontamente comenta os sentidos dos múltiplos fenómenos –éticos, culturais, filosóficos, pragmáticos, etc.– com que a cada passo se confronta e (re)constrói. Operando, antes de mais, em termos de uma concepção lúdica da vida, a anedota distende-se por múltiplas e versáteis conformações de natureza tipológica, tropológica e topológica.