Air flow humidification for air-assisted boom sprayer

The air-assisted ground spray is fairly widespread. However, due to the unpredictable weather conditions, the operational efficiency is impaired by stops on grounds of low humidity and high temperatures. The aim of this work was to assess an air humidification method and evaluate its impact on temperature and air humidity for the air curtain of the air-assisted sprayer. With respect to relative air humidity, it has increased in 6.59%, being the maximum change when inserting 1.92 L min-1. So, it is concluded that the pipeline humidification might significantly reduce temperature and enhance air humidity. The treatments performed in this study consisted of a varied flow of a humidity device, related to weather conditions. Temperature and relative air humidity were measured at 1.0 m height from right to left of middle point of the machine, corresponding to the end of the spray boom, in the middle and end of right spray boom. The readings were also performed at three different distances from the end of the pipeline and at 0.25 and 0.50 m from that to the soil. The results show that 0.48 L min-1 in the humidification system has promoted a better efficiency in reducing air-temperature, on average 2.52 ºC when compared to the non-humidified one.

A simple and rapid screening method for sulfonamides in honey using a flow injection system coupled to a liquid waveguide capillary cell

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Cross linked Poly (4-Vinylpyridine-Ethylene Glycol Dimethacrylate) Used for Preconcentration of Cd(II) and its Determination by Flow Injection Flame Atomic Absorption Spectrometry

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Numerical modeling of flow through an industrial burner orifice

This paper presents numerical modeling of a turbulent natural gas flow through a non-premixed industrial burner of a slab reheating furnace. The furnace is equipped with diffusion side swirl burners capable of utilizing natural gas or coke oven gas alternatively through the same nozzles. The study is focused on one of the burners of the preheating zone. Computational Fluid Dynamics simulation has been used to predict the burner orifice turbulent flow. Flow rate and pressure at burner upstream were validated by experimental measurements. The outcomes of the numerical modeling are analyzed for the different turbulence models in terms of pressure drop, velocity profiles, and orifice discharge coefficient. The standard, RNG, and Realizable k-epsilon models and Reynolds Stress Model (RSM) have been used. The main purpose of the numerical investigation is to determine the turbulence model that more consistently reproduces the experimental results of the flow through an industrial non-premixed burner orifice. The comparisons between simulations indicate that all the models tested satisfactorily and represent the experimental conditions. However, the Realizable k-epsilon model seems to be the most appropriate turbulence model, since it provides results that are quite similar to the RSM and RNG k-epsilon models, requiring only slightly more computational power than the standard k-epsilon model. (C) 2014 Elsevier Ltd. All rights reserved.

Influence of the Extractant on the Complexing Capacity of Humic Substances from Peat for Macro and Micronutrients Using Continuous Flow: Agricultural Application and Environmental Impacts

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A Reproducible Venous Thrombosis Model in Horses Induced by the Combination of an Endothelial Lesion and Blood Flow Stasis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Correlations between ovarian follicular blood flow and superovulatory responses in ewes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Numerical Study of the FENE-CR Model Applied to a Jet Flow Problem

The FENE-CR model is investigated through a numerical algorithm to simulate the time-dependent moving free surface flow produced by a jet impinging on a flat surface. The objective is to demonstrate that by increasing the extensibility parameter L, the numerical solutions converge to the solutions obtained with the Oldroyd-B model. The governing equations are solved by an established free surface flow solver based on the finite difference and marker-and-cell methods. Numerical predictions of the extensional viscosity obtained with several values of the parameter L are presented. The results show that if the extensibility parameter L is sufficiently large then the extensional viscosities obtained with the FENE-CR model approximate the corresponding Oldroyd-B viscosity. Moreover, the flow from a jet impinging on a flat surface is simulated with various values of the extensibility parameter L and the fluid flow visualizations display convergence to the Oldroyd-B jet flow results.

A two-fluid model for refrigerant flow through adiabatic capillary tubes

This work presents a numerical model to simulate refrigerant flow through capillary tubes, commonly used as expansion devices in refrigeration systems. The flow is divided in a single-phase region, where the refrigerant is in the subcooled liquid state, and a region of two-phase flow. The capillary tube is considered straight and horizontal. The flow is taken as one-dimensional and adiabatic. Steady-state condition is also assumed and the metastable flow phenomena are neglected. The two-fluid model, considering the hydrodynamic and thermal non-equilibrium between the liquid and vapor phases, is applied to the two-phase flow region. Comparisons are made with experimental measurements of the mass flow rate and pressure distribution along two capillary tubes working with refrigerant R-134a in different operating conditions. The results indicate that the present model provides a better estimation than the commonly employed homogeneous model. Some computational results referring to the quality, void fraction, velocities, and temperatures of each phase are presented and discussed.

The effect of sets and repetitions of the spirometer by flow in cardiorespiratory parameters

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Endovascular Treatment of Spontaneous Isolated Common and External Iliac Artery Dissections with Preservation of Pelvic Blood Flow

Spontaneous isolated dissection of iliac arteries is very rare, with few reports in the literature. Medical, surgical, and endovascular treatment modalities have all been used to manage iliac artery dissections. We report a case of symptomatic, isolated, spontaneous dissection of the common iliac and external iliac arteries. Both dissections were successfully treated by separate percutaneous stent-graft placement, preserving hypogastric artery flow. This technique is interesting because it provides adequate sealing of proximal and distal dissection sites while preserving hypogastric artery and pelvic flow.

An unequivocal normalization-based paradigm to solve dynamic economic and emission active-reactive OPF (optimal power flow)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Screening and determination of sulphonamide residues in bovine milk samples using a flow injection system

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sensitive flow-injection spectrophotometric analysis of bromopride

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)