Brake system performance requirements of a lightweight electric/hybrid rear wheel drive vehicle

Investigates the braking performance requirements of the UltraCommuter, a lightweight series hybrid electric vehicle currently under development at the University of Queensland. With a predicted vehicle mass of 600 kg and two in-wheel motors each capable of 500 Nm of peak torque, decelerations up to 0.46 g are theoretically possible using purely regenerative braking. With 99% of braking demands less than 0.35 g, essentially all braking can be regenerative. The wheel motors have sufficient peak torque capability to lock the rear wheels in combination with front axle braking, eliminating the need for friction braking at the rear. Emergency braking levels approaching 1 g are achieved by supplementation with front disk brakes. This paper presents equations describing the peak front and rear axle braking forces which occur under straight line braking, including gradients. Conventionally, to guarantee stability, mechanical front/rear proportioning of braking effort ensures that the front axle locks first. In this application, all braking is initially regenerative at the rear, and an adaptive ''by-wire'' proportioning system presented ensures this stability requirement is still satisfied. Front wheel drive and all wheel drive systems are also discussed. Finally, peak and continuous performance measures, not commonly provided for friction brakes, are derived for the UltraCommuter's motor capability and range of operation.

A method of switch selection for an electric vehicle drive

The key to reducing cost of electric vehicles is integration. All too often systems such as the motor, motor controller, batteries and vehicle chassis/body are considered as separate problems. The truth is that a lot of trade-offs can be made between these systems, causing an overall improvement in many areas including total cost. Motor controller and battery cost have a relatively simple relationship; the less energy lost in the motor controller the less energy that has to be carried in the batteries, hence the lower the battery cost. A motor controller’s cost is primarily influenced by the cost of the switches. This paper will therefore present a method of assessing the optimal switch selection on the premise that the optimal switch is the one that produces the lowest system cost, where system cost is the cost of batteries + switches.

Unidentified vehicle in multi-vehicle accident - failure to notify Nominal Defendant no bar to proceedings against it

In Kumar v Suncorp Metway Insurance Limited [2004] QSC 381 Douglas J examined s37 of the Motor Accident Insurance Act 1994 (Qld) in the context of an accident involving multiple insurers when a notice of accident had not been given to the Nominal Defendant

Determinants of second row passenger comfort

China is becoming an increasingly important automotive market. Customer’s vehicle usage, preferences and requirements differ from traditional western markets in a number of aspects – rear seat usage rates are higher, vehicles are used for business purposes as well as for private transport and rear seat usage is generally more important to Chinese customers compared to their western counterparts. The purpose of this project is to dimension and investigate these differences from an ergonomics perspective and use these results to guide the design of future products. The focus for this project will be specific to vehicles in the CD segment. More specifically, this project focuses on the second row ‘ambience’. Ambience refers to the global feeling perceived by second row passengers, and the main factors contributing to ambience are: ingress and egress comfort, seat comfort, roominess, and ease of use of the controls. In order to investigate the aforementioned parameters, an experimental study has been conducted in Shanghai, China. This experiment involved 80 healthy Chinese CD- and D-car customers. These subjects were asked to evaluate different features present in the second row environment of three different cars: A Ford Mondeo, Toyota Camry and Mercedes S-class. Various data has been collected during this experiment: First, the anthropometric dimensions of the subjects have been measured. The subjects were also asked to fill a questionnaire about demographics, their own car usage, and their perception of a various number of features present in the three tested cars. A great amount of technical data was also collected. The first part of this report presents the results given by the questionnaires. It includes Chinese demographics, vehicle usage habits, and the subjective perception of the features present in the tested cars. It also presents the results of the anthropometric measurements. This gives a first insight into Chinese customers’ habits and preferences. The second part deals with the technical data recorded during the experiment: second row seat adjustment ranges, roominess, optimal location of controls, and pressure mapping analysis. Analysis of technical data allows a deeper understanding of the factors contributing to comfort and ambience perception. Using the technical data together with the comfort ratings given by the subjects in the questionnaire, recommendations on several design parameters were provided. Finally, an experimental study of car ingress-egress has been conducted in a University laboratory controlled environment. During this study, the ingress and egress motion of 20 customers from Chinese origin was recorded using a motion capture system. The last part of this report presents the protocol and data processing that led to building an ingress-egress motion database that was provided to Ford.

Socio-cultural influences on vehicle defects in the Omani heavy vehicle industry

With recent economic growth in Oman there is increased use of heavy vehicles, presenting an increase in heavy vehicle crashes, associated fatalities and injuries. Vehicle defects cause a significant number of heavy vehicle crashes in Oman and increase the likelihood of fatalities. The aim of this study is to explore factors contributing to driving with vehicle defects in the Omani heavy vehicle industry. A series of qualitative participants observations were conducted in Oman with 49 drivers. These observations also involved discussion and interviews with drivers. The observations occurred at two road-side locations where heavy vehicle drivers gather for eating, resting, vehicle check-up, etc. Data collection was conducted over a three week period. The data was analysed using thematic analysis. A broad number of factors were identified as contributing to the driving of vehicles with defects. Participants indicated that tyres and vehicle mechanical faults were a common issue in the heavy vehicle industry. Participants regularly reported that their companies use cheap, poor quality standards parts and conducted minimal maintenance. Drivers also indicated that they felt powerless to resist company pressure to drive vehicles with known faults. In addition, drivers reported that traffic police were generally in effective and lacked skill to appropriately conduct roadside inspection on trucks. Further, participants stated that it was possible for companies to avoid being fined during annual or roadside vehicle inspections if members of the company knew the traffic police officer conducting the inspection. Moreover, fines issued by police are generally directed to the individual driver rather than being applied to the company, thus providing no incentive for companies to address vehicle faults. The implications of the findings are discussed.

Safety culture and speeding in the Australian heavy vehicle industry

Inappropriate speed and speeding are among the highest causes of crashes in the heavy vehicle industry. Truck drivers are subjected to a broad range of influences on their behaviour including industrial pressures, company monitoring and police enforcement. Further, drivers have a high level of autonomy over their own behaviour. As such it is important to understand how these external influences interact with commonly shared beliefs, attitudes and values of heavy vehicle drivers to influence their behaviour. The present study uses a re-conceptualisation of safety culture to explore the behaviours of driving at an inappropriate speed and speeding in the heavy vehicle industry. A series of case studies, consisting of interviews and ride-along observations, were conducted with three transport organisations to explore the effect of culture on safety in the heavy vehicle industry. Results relevant to inappropriate speed are reported and discussed. It was found that organisational management through monitoring, enforcement and payment, police enforcement, customer standards and vehicle design factors could all reduce the likelihood of driving at inappropriate speeds under some circumstances. However, due to weaknesses in the ability to accurately monitor appropriate speed, this behaviour was primarily influenced by cultural beliefs, attitudes and values. Truck drivers had a tendency to view speeding as relatively safe, had a desire to speed to save time and increase personal income, and thus often attempted to speed without detection. When drivers saw speeding as dangerous, however, they were more likely to drive safely. Implications for intervention are discussed.

The National Road Safety Partnership Program providing a pathway for any business/organisation to create a positive road safety culture

The National Road Safety Partnership Program (NRSPP) is an industry-led collaborative network which aims to support Australian businesses in developing a positive road safety culture. It aims to help businesses to protect their employees and the public, not only during work hours, but also when their staff are ‘off-duty’. How do we engage and help an organisation minimise work-related vehicle crashes and their consequences both internally, and within the broader community? The first step is helping an organisation to understand the true cost of its road incidents. Larger organisations often wear the costs without knowing the true impact to their bottom line. All they perceive is the change in insurance or vehicle repairs. Understanding the true cost should help mobilise a business’s leadership to do more. The next step is ensuring the business undertakes an informed, structured, evidence-based pathway which will guide them around the costly pitfalls. A pathway based around the safe system approach with buy-in at the top which brings the workforce along. The final step, benchmarking, allows the organisation to measure and track its change. This symposium will explore the pathway steps for organisations using NRSPP resources to become engaged in road safety. The 'Total Cost of Risk' calculator has been developed by Zurich, tested in Europe by Nestle and modified by NRSPP for Australia. This provides the first crucial step. The next step is a structured approach through the Workplace Road Safety Guide using experts and industry to discuss the preferred safe system approach which can then link into the national Benchmarking Project. The outputs from the symposium can help frame a pathway for organisations to follow through the NRSPP website.

Evidence-based perspective on CP rehabilitation : Reviews on physiotherapy, physiotherapy-related motor-based interventions and orthotic devices

This thesis utilises an evidence-based approach to critically evaluate and summarize effectiveness research on physiotherapy, physiotherapy-related motor-based interventions and orthotic devices in children and adolescents with cerebral palsy (CP). It aims to assess the methodological challenges of the systematic reviews and trials, to evaluate the effectiveness of interventions in current use, and to make suggestions for future trials Methods: Systematic reviews were searched from computerized bibliographic databases up to August 2007 for physiotherapy and physiotherapy-related interventions, and up to May 2003 for orthotic devices. Two reviewers independently identified, selected, and assessed the quality of the reviews using the Overview Quality Assessment Questionnaire complemented with decision rules. From a sample of 14 randomized controlled trials (RCT) published between January 1990 and June 2003 we analysed the methods of sampling, recruitment, and comparability of groups; defined the components of a complex intervention; identified outcome measures based on the International Classification of Functioning, Disability and Health (ICF); analysed the clinical interpretation of score changes; and analysed trial reporting using a modified 33-item CONSORT (Consolidated Standards of Reporting Trials) checklist. The effectiveness of physiotherapy and physiotherapy-related interventions in children with diagnosed CP was evaluated in a systematic review of randomised controlled trials that were searched from computerized databases from January 1990 up to February 2007. Two reviewers independently assessed the methodological quality, extracted the data, classified the outcomes using the ICF, and considered the level of evidence according to van Tulder et al. (2003). Results: We identified 21 reviews on physiotherapy and physiotherapy-related interventions and five on orthotic devices. These reviews summarized 23 or 5 randomised controlled trials and 104 or 27 observational studies, respectively. Only six reviews were of high quality. These found some evidence supporting strength training, constraint-induced movement therapy or hippotherapy, and insufficient evidence on comprehensive interventions. Based on the original studies included in the reviews on orthotic devices we found some short-term effects of lower limb casting on passive range of movement, and of ankle-foot orthoses on equinus walk. Long term effects of lower limb orthoses have not been studied. Evidence of upper limb casting or orthoses is conflicting. In the sample of 14 RCTs, most trials used simple randomisation, complemented with matching or stratification, but only three specified the concealed allocation. Numerous studies provided sufficient details on the components of a complex intervention, but the overlap of outcome measures across studies was poor and the clinical interpretation of observed score changes was mostly missing. Almost half (48%) of the applicable CONSORT-based items (range 28 32) were reported adequately. Most reporting inadequacies were in outcome measures, sample size determination, details of the sequence generation, allocation concealment and implementation of the randomization, success of assessor blinding, recruitment and follow-up dates, intention-to-treat analysis, precision of the effect size, co-interventions, and adverse events. The systematic review identified 22 trials on eight intervention categories. Four trials were of high quality. Moderate evidence of effectiveness was established for upper extremity treatments on attained goals, active supination and developmental status, and of constraint-induced therapy on the amount and quality of hand use and new emerging behaviours. Moderate evidence of ineffectiveness was found for strength training's effect on walking speed and stride length. Conflicting evidence was found for strength training's effect on gross motor function. For the other intervention categories the evidence was limited due to the low methodological quality and the statistically insignificant results of the studies. Conclusions: The high-quality reviews provide both supportive and insufficient evidence on some physiotherapy interventions. The poor quality of most reviews calls for caution, although most reviews drew no conclusions on effectiveness due to the poor quality of the primary studies. A considerable number of RCTs of good to fair methodological and reporting quality indicate that informative and well-reported RCTs on complex interventions in children and adolescents with CP are feasible. Nevertheless, methodological improvement is needed in certain areas of the trial design and performance, and the trial authors are encouraged to follow the CONSORT criteria. Based on RCTs we established moderate evidence for some effectiveness of upper extremity training. Due to limitations in methodological quality and variations in population, interventions and outcomes, mostly limited evidence on the effectiveness of most physiotherapy interventions is available to guide clinical practice. Well-designed trials are needed, especially for focused physiotherapy interventions.

Significance of a short-term test drive for prospective plug-in electric vehicle consumers: An exploratory study

The test drive is a well-known step in car buying. In the emerging plug-in electric vehicle (PEV) market, however, the influence of a pre-purchase test drive on a consumer's inclination to purchase is unknown. Policy makers and industry participants both are eager to understand what factors motivate vehicle consumers at the point-of-sale. A number of researchers have used choice models to shed light on consumer perceptions of PEVs, and others have investigated consumer change in disposition toward a PEV over the course of a trial, wherein test driving a PEV may take place over a number of consecutive days, weeks or months. However, there is little written on the impact of a short-term test drive - a typical experience at dealerships or public "ride-and-drive" events. The impact of a typical test drive, often measured in minutes of driving, is not well understood. This paper first presents a synthesis of the literature on the effect of PEV test drives as they relate to consumer disposition toward PEVs. An analysis of data obtained from an Australian case study whereby attitudinal and stated preference data were collected pre- and post- test drive at public "ride-and-drive" event held Brisbane, Queensland in March 2014 using a custom-designed iPad application. Motorists' perceptions and choice preferences around PEVs were captured, revealing the relative importance of their experience behind the wheel. Using the Australian context as a case-study, this paper presents an exploratory study of consumers' stated preferences toward PEVs both before and after a short test drive.

Reforming technology company incentive programs for achieving knowledge-based economic development:a Brazil-Australia comparative study

This doctoral thesis aims to demonstrate the importance of incentives to technology-based firms as a strategy to promote knowledge-based economic development (KBED). To remain competitive, technology-based firms must innovate and seek new markets; therefore, this study aims to propose an incentive model to technology-based firms as a strategy to promote knowledge-based urban development, according to framework described by Yigitcanlar (2011). This is an exploratory and descriptive research with a qualitative approach. Surveys were carried out with national trade associations that represented technology-based firms both in Brazil and Australia. After analysing the surveys, structured interviews were conducted with government representatives, trade associations and businessmen who had used financial support by the federal government. When comparing both countries, the study found the importance of direct incentives through tax incentives, for it is a less bureaucratic, quicker and more direct process for firms. We suggest to include the terms incentives in the framework of knowledge-based urban development, as one of the pillars that contribute to knowledge-based economic development.

Ruumis ja rauta : esseitä esineiden sosiaalisuudesta

"Body and Iron: Essays on the Socialness of Objects" focuses on the bodily-material interaction of human subjects and technical objects. It poses a question, how is it possible that objects have an impact on their human users and examines the preconditions of active efficacy of objects. In this theoretical task the work relies on various discussions drawing from realistic ontology, phenomenology of body, neurophysiology of Antonio Damasio and psychoanalysis to establish both objects and bodies as material entities related in a causal interaction with each other. Out of material interaction emerge a symbolic field, psyche and culture that produce representations of interactions with material world they remain dependent on and conditioned by. Interaction with objects informs the human body via its somatosensory systems: interoseptive and proprioseptive (or kinesthetic) systems provide information to central nervous system of the internal state of the body and muscle tensions and motor activity of the limbs. Capability to control the movements of one's body by the internal "feel" of being a body turns out to be a precondition to the ability to control artificial extensions of the body. Motor activity of the body is involved in every perception of environment as the feel of one's own body is constitutive of any perception of external objects. Perception of an object cause changes in the internal milieu of the body and these changes in the organism form a bodily representation of an external object. Via these "muscle images" the subject can develop a feel for an instrument. Bodily feel for an object is pre-conceptual, practical knowledge that resists articulation but allows sensing the world through the object. This is what I would call sensual knowledge. Technical objects intervene between body and environment, transforming the relation of perception and motor activity. Once connected to a vehicle, human subject has to calibrate visual information of his or her position and movement in space to the bodily actions controlling the machine. It is the machine that mediates the relation of human actions to the relation of her body to its environment. Learning to use the machine necessarily means adjusting his or her bodily actions to the responses of the machine in relation to environmental changes it causes. Responsiveness of the machine to human touch "teaches" its subject by providing feedback of the "correctitude" of his or her bodily actions. Correct actions form a body technique of handling the object. This is the way of socialness of objects. While responding to human actions they generate their subjects. Learning to handle a machine means accepting the position of the user in the program of action materialized in the construction of the object. Objects mediate, channel and transform the relation of the body to its environment and via environment to the body itself according to their material and technical construction. Objects are sensory media: they channel signals and information from the environment thus constituting a representation of environment, a virtual or artificial reality. They also feed the body directly with their powers equipping their user with means of regulating somatic and psychic states of her self. For these reasons humans look for the company of objects. Keywords: material objects, material culture, sociology of technology, sociology of body, mobility, driving

Varities of National Metonymy in Media Accounts of International Mergers and Acquisitions

International mergers and acquisitions (M&As) often invoke national identification and national cultural differences. We argue that metonymy is a central linguistic resource through which national cultural identities and differences are reproduced in media accounts of international M&As. In this paper, we focus on two revealing cases: the acquisition of American IBM Personal Computer Division (PCD) by the Chinese company Lenovo and the acquisition of American Anheuser-Busch (A-B) by the Belgian-Brazilian company InBev. First, we identify the forms, functions and frequencies of national metonymy in media accounts of these cases. We present a typology that classifies varieties of national metonymy in international M&As. Second, we demonstrate how these metonyms combine with metaphor to generate evocative imagery, engaging wit, and subversive irony. Our findings show that national metonymy contributes to the construction of emotive frames, stereotypes, ideological differences, and threats. Combinations of national metonymy with metaphor also provide powerful means to construct cultural differences. However, combinations of metonymy with wit and irony enable the play on meanings that overturns and resists national and cultural stereotypes. This is the first study to unpack the deployment of metonymy in accounts of international M&As. In doing so, it also opens up new avenues for research into international management and the analysis of tropes in management and organization.

Gender and National Identity Constructions in the Cross-Border Merger Context

In this article we explore ways in which vertical gender inequality is accomplished in discourse in the context of a recent chain of cross-border mergers and acquisitions that resulted in the formation of a multinational Nordic company. We analyse social interactions of ‘doing’ gender in interviews with male senior executives from Denmark, Finland and Sweden. We argue that their explanations for the absence of women in the top echelons of the company serve to distance vertical gender inequality. The main contribution of the article is an analysis of how national identities are discursively (re)constructed in such distancing. New insights are offered to studying gender in multinationals with a cross-cultural team of researchers. Our study sheds light on how gender intersects with nationality in shaping the multinational organization and the identities of male executives in globalizing business.